Table of Contents
Advertisement
Sectional and Tilting Door Opener
Installation Instructions and User Guide
SDO 800
SDO1000
S/N
WARNING
Please read the manual carefully before installation and use. The installation of your
new door opener must be carried out by a technically qualified or licensed person.
Attempting to install or repair the door opener without suitable technical qualification
may result in severe personal injury, death and / or property damage.
Advertisement
Table of Contents
Related Manuals for Napoleon SDO1000
Summary of Contents for Napoleon SDO1000
- Page 1 Sectional and Tilting Door Opener Installation Instructions and User Guide SDO 800 SDO1000 WARNING Please read the manual carefully before installation and use. The installation of your new door opener must be carried out by a technically qualified or licensed person.
-
Page 2: Table Of Contents
CONTENTS Important Safety Recommendations...…………………………….……………………………..1-2 Basic function introduction………………………………………………………………………..2 Special function introduction………….……………………..……………………………………..2 Installation (aluminum track)………………………………………….…………………………..3-4 Installation (steel track)………………………………………….…………………………….…….5 Installation recommendations……………………………………………………………………..6 Basic function setting and applying………………………………………………………………7-8 Special function introduction and application………………………………………….……….9-10 PCB structure………………..…………………………………………………………..………..10 Aluminum, steel & sectional steel accessory list…………………..…………………….……...11 Manual disengagement…………………………………………………………………………….12 Maintenance………………………………………………………………………………………...12 Technical specifications…………………………………………………………………………….13 Final note….………………………………………………………………………………………...13... -
Page 3: Important Safety Recommendations
Important safety recommendations FAILURE TO COMPLY WITH THE FOLLOWING SAFETY RECOMMENDATIONS MAY RESULT IN SERIOUS PERSONAL INJURY, DEATH AND / OR PROPERTY DAMAGE. 1. PLEASE READ CAREFULLY AND ADHERE TO ALL SAFETY AND INSTALLATION RECOMMENDATIONS. 2. The opener is designed and manufactured to meet local regulations. The installer must be familiar with local regulations required in respect of the installation of the opener. -
Page 4: Basic Function Introduction
due to weak or broken springs, or being out of balance. Frequently examine the installation, in particular check cables, springs and mountings for signs of wear, damage or imbalance. Do not use if repair or adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury. -
Page 5: Installation (Aluminum Track)
Referring to Fig. 2 for recommended installation 1) Sectional door rail 5) O/S/C button 2) 24V DC flash light (optional part ) 6) Power socket 3) Wall switch(optional part ) 7) Door opener 4) Photo beam (RX/TX Type) CHA IN SHUTTLE A SSEMBLY As for the ease of the chain, it is delivered with the chain and chain shuttle already assembled in the track. - Page 6 Before attaching the motor brackets (E) (FIG 4) screw an inverted nut (6mm) (D) on each stud then position the brackets (E) on the studs and secure them in-place using a second 6mm-nut and then lock the brackets to the rail by tightening the inverted lock nuts (D).
-
Page 7: Installation (Steel Track)
Installation (steel track) Fig. 1 1. Fixing the track bracket. Fixing the track bracket to the wall 2cm-15cm over the shaft or intermediate bracket (depend on the actual installation space). 2. Fixing the steel track to the bracket with copper pin. (Fig. 1) 3. -
Page 8: Installation Recommendations
Installation recommendations there are specific standards that have to be strictly followed regarding the safety Remember rules of electrical installations and automatic gates and doors. As for the legal requirements and standards that must be adhered to, please take notice of the following points to ensure maximum safety and reliability of your installation. -
Page 9: Basic Function Setting And Applying
Basic function setting and applying 1. Travel limit setting Opening & closing force self-learning 1. Press ‘SET’ button and hold on until the LED displays figure ‘1’, 2. Then adjust the up limit by pressing ‘LIM-1’ button. Fine-tuning ‘LIM-1’ or ‘LIM-2’ button to determine the final up limit position then press ‘set’... - Page 10 3. Safety reverse force adjustment 1. Press ‘SET’ button and hold on until the LED displays ‘3’. It’s under force adjustment mode. 2. Press ‘LIM-1’ button to increase the force and ‘LIM-2’ button to decrease the force. 3. The maximum force is 9 and the minimum is 1. Press ‘SET’...
-
Page 11: Special Function Introduction And Application
Special function introduction and application The following functions are made to order in accordance with the special needs of customers: 1. The O/S/C interfaces available Add another O/S/C button to open or close the door. 2. Auto safety reverse function This special function is for safety consideration. -
Page 12: Pcb Structure
Fig. 3 PCB structure... -
Page 13: Aluminum, Steel & Sectional Steel Accessory List
Steel track accessory list (Chain Drive & Belt Drive) Item Quantity Clutch Components Bracket for door panel Bracket for Wall Clutch cord Cord pendant ø 1.8×38 Cotter pin M6X14 hexagon head bolt M6 flange nut ø 8×25 axis pin M8X16 hexagon head bolt M8 flange nut Motor bracket Ø6*90 axis pin... -
Page 14: Manual Disengagement
Manual disengagement The opener is equipped with a manual release cord to disengage shuttle and move door by hand while holding the handle down (Fig 12). Pull on the handle to disengage the shuttle. To re-engage the door simply run opener in automatic mode or move door by hand until the trolley engages in the chain shuttle. -
Page 15: Final Note
Final notes This manual is only used by technical persons who are qualified to carry out the installation. No given information in this manual can be considered of any interest to the end user. It is important for the installer to show their clients correct operation using of the opener including the using of manual disengagement cord.
Need help?
Do you have a question about the SDO1000 and is the answer not in the manual?
Questions and answers