Page 1
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No. 769-10302A...
See How-to Maintenance and Parts Installation Videos at www.cubcadet.com/tutorials ◊ Call a Customer Support Representative at (800) 965-4CUB ◊ Locate your nearest Cub Cadet Dealer at (877) 282-8684 ◊ Write to Cub Cadet LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019...
Important Safe Operation Practices WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.
Page 4
Slope Operation A missing or damaged discharge cover can cause blade contact or thrown object injuries. Slopes are a major factor related to loss of control and tip-over Stop the blade(s) when crossing gravel drives, walks, or accidents which can result in severe injury or death. All slopes roads and while not cutting grass.
Page 5
Service Children Tragic accidents can occur if the operator is not alert to the Safe Handling of Gasoline: presence of children. Children are often attracted to the machine and the mowing activity. They do not understand To avoid personal injury or property damage use extreme the dangers.
Do not modify engine Periodically check to make sure the blades come to complete stop within approximately (5) five seconds after To avoid serious injury or death, do not modify engine in any operating the blade disengagement control. If the blades way.
Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate DANGER —...
Assembly & Set-Up Contents of Crate • One Tractor • One Operator’s Manual • One Engine Operator’s Manual NOTE: This Operator’s Manual covers several models. Tractor Install Operator’s Seat (If necessary) features may vary by model. Not all features in this manual are WARNING! Before operating the tractor, make applicable to all tractor models and the tractor depicted may...
Page 10
Lower Deck Discharge Chute Deflector Rotate the seat into position and secure the seat into place with the previously removed shoulder screws and flange WARNING! Never operate the mower deck lock nuts. Be careful not to crimp or damage the wire without the chute deflector installed and in the harness while installing the seat.
Page 11
Installing the Dash Cap (If necessary) Secure the steering wheel with the hex bolt from under the cap and torque to 18-22 ft./lbs. To install the dash cap (1), line up the tabs (2) on the dash cap (1) Place the steering wheel cap over the center of the steering with the holes in the upper dash as shown in Figure 3-7.
Page 12
Adjusting the Seat Remove the plastic cover, if present, from the positive battery terminal and attach the red cable to the positive battery To adjust the position of the seat, lift the seat adjustment lever terminal (+) with the bolt and hex nut. See Figure 3-11. up.
Page 13
Setting the Deck Wheels Gas & Oil WARNING!: Keep hands and feet away from the The fuel tank is located at the outer/left of the dash and holds discharge opening of the cutting deck. 3 gallons of gas. Remove the fuel cap by turning it counter- clockwise.
Controls & Features Fuel Tank Cap Throttle/Choke Hour Meter Control Lever Ignition Module or Throttle Control Lever (If so equipped) Forward Drive Pedal Reverse Drive Pedal PTO Switch (If Choke Control Brake Pedal so equipped) PTO Handle (If so equipped) Park Brake/Cruise Control Lever Deck Lift Lever...
Page 15
Throttle/Choke Control Lever Ignition Module (If so equipped) WARNING! Never leave a running The throttle/choke control lever is located on the left machine unattended. side of the tractor’s dash panel. This lever controls the Always disengage speed of the engine and, when pushed all the way PTO, set parking brake, stop forward, past the detent position closes the choke for engine and remove key to prevent...
Maintenance section of the Engine Operator’s Manual air filter, blades or battery. Cub Connect™ also enables you to locate and contact Cub Cadet Service Centers, access step-by- step instructions to perform routine maintenance and purchase replacement parts directly from your mobile device.
Doing so will result in a “rich” fuel mixture protection of the operator. If the interlock system should ever and cause the engine to run poorly and can damage the malfunction, do not operate tractor. Contact your Cub Cadet dealer. engine. •...
Reverse Caution Mode The REVERSE CAUTION MODE will remain activated until: The REVERSE CAUTION MODE position of the ignition The key is placed in either the NORMAL MOWING module allows the tractor to be operated in reverse with the blades (PTO) engaged. position or STOP position or NOTE: Mowing in reverse is not recommended.
Driving On Slopes Release pressure from the parking brake/cruise control lever . After completing step 3, the forward drive pedal should remain Refer to the SLOPE GAUGE on page 8 to help determine slopes in the down position and the tractor will maintain the same where you may operate the tractor safely.
Page 20
Engaging the PTO (Manual PTO tractors) Slowly press the forward drive pedal with your right foot until the desired speed is achieved. Engaging the PTO transfers power to the cutting deck or other NOTE: The speed of the tractor will affect the quality of the (separately available) attachments.
Maintenance & Adjustments Maintenance Schedule Before After First Every 10 Every 25 Every 50 Every 100 Prior to Engine Each use 5 Hours Hours Hours Hours Hours Storing Manual Check & Clean Engine Cooling Fans for Debris Check Engine Oil Level Check Air Filter for Dirty, Loose or Damaged Parts Clean Battery Terminals Grease All Lubrication Points...
If the tractor creeps forward or rearward when neither the forward To complete an oil change, proceed as follows: nor reverse pedal is depressed, contact your local Cub Cadet Run the engine for a short time to warm the engine oil. The dealer to have the neutral setting properly adjusted.
Cleaning the Tractor Turn the water off and detach the hose coupler from the water port on your deck’s surface. Any fuel or oil spilled on the machine should be wiped off promptly. NOTE: On 50” and 54” decks there are two water ports; one on each side of the deck.
Deck Wheels To lower the front of the deck, loosen the outer nut then loosen (thread outward) the nut, away from the front The wheels on the deck which are spherical shaped (50” and 54” hanger bracket. See Figure 6-5. When proper adjustment is decks have 4) are equipped with a grease fitting.
Measure the distance from the outside of the left blade Engines stored between 30 and 90 days need to be treated with a gasoline stabilizer such as STA-BIL® and engines stored over tip to the ground and the distance from the outside of the 90 days need to be run empty of fuel to prevent deterioration right blade tip to the ground.
Connect positive (+) cable to positive (+)post of your Cub Cadet Service Dealer. tractor’s discharged battery. Cutting Deck Removal Connect the other end of the cable to the positive (+) post of the jumper battery.
Page 27
Slide the rod to the right to remove it. Looking at the cutting deck from the left side of the tractor, locate the bow-tie pin on the rear left side of the deck. See NOTE: Be careful not to damage the wire harness when Figure 7-4.
Cutting Blades To properly sharpen the cutting blades, remove equal amounts of metal from both ends of the blades along the cutting edges, parallel to the trailing edge, at a 25°- to 30° WARNING! Shut the engine off and remove angle.
Page 29
Changing the Transmission Drive Belt Several components must be removed and special tools used in order to change the tractor’s transmission drive belt. See your Cub Cadet dealer to have the transmission drive belt replaced. 7 — S ection ervice...
Page 34
FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS MTD Consumer Group Inc, the United States Environmental Protection Agency (EPA), and for those products certified for sale in the state of California, the California Air Resources Board (CARB) are pleased to explain the evaporative emission control system (ECS) warranty on your 2014-2015 small off-road equipment (outdoor equipment).
Page 35
WARRANTED PARTS: The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if MTD Consumer Group Inc demonstrates that the outdoor equipment has been abused, neglected, or improperly maintained, and that such abuse, neglect, or improper maintenance was the direct cause of the need for repair or replacement of the part.
Page 36
No other express warranties Frame and Front Axle — Cub Cadet warrants the frame, and front cast iron beyond those mentioned above, given by any person or entity,...
Page 37
LEA Y CUMPLA TODAS LAS REGLAS Y LAS INSTRUCCIONES DE SEGURIDAD DE ESTE MANUAL ANTES DE INTENTAR OPERAR ESTA MÁQUINA. SI NO RESPETA ESTAS INSTRUCCIONES PUEDE PROVOCAR LESIONES PERSONALES. CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Impreso en EE.UU. Formulario Nº 769-10302A...
Page 38
◊ Llame a un representante de Asistencia al Cliente al (800) 965-4CUB ◊ Localice a su distribuidor Cub Cadet más cercano llamando al (877) 282-8684 ◊ Escriba a Cub Cadet LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019...
Page 39
Importantes medidas de seguridad ¡ADVERTENCIA! La presencia de este símbolo indica que se trata de instrucciones de seguridad importantes que debe respetar para evitar poner en riesgo su seguridad personal y/o material y la de los demás. Lea y cumpla todas las instrucciones de este manual antes de intentar operar esta máquina.
Page 40
Funcionamiento en pendiente Una cubierta de descarga faltante o dañada puede provocar lesiones por contacto con la cuchilla o por objetos arrojados. Las pendientes son un factor importante relacionado con Detenga las cuchillas al cruzar sendas, senderos o caminos de accidentes por pérdida de control y vuelcos que pueden producir grava y cuando no corte césped.
Page 41
Servicio Niños Pueden ocurrir accidentes trágicos si el operador no está Manejo seguro de la gasolina: atento a la presencia de niños. Por lo general, los niños se sienten atraídos por la máquina y su actividad. No entienden Para evitar lesiones personales o daños materiales tenga los riesgos ni los peligros.
Page 42
Si no lo hace, pueden producirse su unidad debe ser reparada por su distribuidor de servicio accidentes, lesiones o la muerte. autorizado Cub Cadet. No modifique el motor Controle el funcionamiento de los frenos con frecuencia, ya que está...
Page 43
Símbolos de seguridad En esta página se presentan y describen los símbolos de seguridad que en este producto puede tener. Lea, entienda y siga todas las instrucciones incluidas en la máquina antes de intentar armarla y hacerla funcionar. Símbolo Descripción LEA LOS MANUALES DEL OPERADOR Lea, entienda y siga todas las instrucciones incluidas en los manuales antes de intentar armarla y hacerla funcionar.
Page 44
2 — i ección mportanteS medidaS de Seguridad...
Page 45
Montaje y Configuración Contenido del cajón • Un Tractor • Un Manual del operador • Un Manual de operación del motor Instale el asiento del operador (si corresponde) NOTA: Este manual de operación cubre distintos modelos. Las características del tractor pueden variar según los modelos. No todas las Para instalar el asiento proceda de la siguiente manera: características en este manual se aplican a todos los modelos de tractor y la máquina que se ilustra aquí...
Page 46
Baje el deflector del canal de descarga de la plataforma Gire el asiento hasta la posición deseada y asegúrelo en su lugar con los tornillos de reborde y las tuercas de seguridad con brida ¡ADVERTENCIA! que extrajo antes. Tenga cuidado de no doblar o dañar el cableado Nunca opere la plataforma de corte sin el deflector del canal de descarga instalado y en mientras instala el asiento.
Page 47
Instalación de la cubierta del tablero (si corresponde) Fije el volante con el perno hexagonal de debajo de la tapa y apriete a 18-22 ft. / Lbs. Para instalar la cubierta del tablero (1), alinear las lengüetas (2) de la Coloque la tapa del volante encima del centro del volante y empuje cubierta del tablero (1) con los orificios de la parte superior del tablero hacia abajo hasta que haga clic al calzar en su lugar.
Page 48
Ajuste del asiento Retire la cubierta plástica, si es que está presente, del borne positivo de la batería y una el cable rojo al borne positivo de la Para ajustar la posición del asiento, levante la palanca de ajuste del batería (+) utilizando el perno y la tuerca hexagonal.
Page 49
Ajuste de las ruedas de la plataforma Gasolina y aceite ¡ADVERTENCIA! El depósito de combustible se encuentra en el exterior/izquierdo del Mantenga las manos y pies alejados tablero y contiene 3 galones de gas. Extraiga la tapa de combustible de la abertura de descarga de la plataforma de corte. girándola hacia la izquierda.
Controles y Características Tapón del depósito de combustible Medidor Acelerador/Cebador horario Palanca de control o palanca de control Módulo de encendido del acelerador (si está equipada) Pedal de la transmisión marcha adelante Pedal de la transmisión Interruptor de hacia atrás Control del la PTO (si está...
Page 51
Palanca de control del acelerador/ Módulo de encendido cebador (si está equipada) ¡ADVERTENCIA! Nunca deje la máquina La palanca de control del regulador / cebador se encuentra funcionando sin en el lado izquierdo del panel de instrumentos del tractor. vigilancia. Siempre Esta palanca controla la velocidad del motor y, cuando se desconecte la toma de empuja totalmente hacia adelante, más allá...
Page 52
Cub Connect™ también le permite localizar y ponerse en contacto con los Cub Cadet Centros de Servicio, Acceso, paso a paso las instrucciones para realizar piezas de mantenimiento y de reemplazo compra de rutina directamente desde su dispositivo móvil.
Page 53
Si el sistema de bloqueo llegara a funcionar mal, (rápida). Funcionar con el acelerador a menos de máxima velocidad no opere el tractor. Póngase en contacto con su distribuidor Cub Cadet. puede acortar la vida útil de la batería.
Page 54
Modo marcha atrás con precaución El MODO DE MARCHA ATRÁS CON PRECAUCIÓN mantendrá activado hasta que: La posición MODO MARCHA ATRÁS CON PRECAUCIÓN La llave se coloque ya sea en la posición CORTE NORMAL módulo de encendido permite operar el tractor marcha atrás con las cuchillas (PTO) acopladas.
Page 55
Operación en pendiente Después de completar el paso 3, el pedal de marcha adelante debe permanecer en la posición hacia abajo y el tractor mantendrá la misma no está Consulte la sección INDICADOR DE PENDIENTE en la página 8 para velocidad de avance.
Page 56
Acople de la PTO (Tractores con PTO manual) Baje la plataforma de corte al ajuste de altura deseado usando la manija de elevación de la plataforma. Al conectar la PTO se suministra energía a la plataforma de corte y a otros Presione lentamente el pedal de marcha adelante con el pie accesorios (disponibles por separado).
Mantenimiento y Ajustes Programa de mantenimiento Después de Consulte el Antes de Cada 10 Cada 25 Cada 50 Cada 100 Antes de las primeras manual del cada uso horas horas horas horas almacenar 5 horas motor Revise y limpie de residuos los ventiladores de refrigeración del motor Revise el nivel de aceite del motor.
Page 58
Para realizar el cambio de aceite, proceda de la siguiente manera: local Cub Cadet que realice el ajuste neutral correctamente ajustado. Haga funcionar el motor por un período corto para calentar el aceite del motor.
Page 59
Limpieza del tractor Desconecte el agua y retire el acoplador de la manguera desde el puerto de agua que se encuentra en la superficie de la plataforma. Si se derrama combustible o aceite sobre la máquina, debe limpiarse NOTA: En las plataformas de 50 y 54 pulgadas hay dos puertos de de inmediato.
Page 60
Ruedas de la plataforma bajar Para el frente de la plataforma, afloje la tuerca exterior y afloje (rosca hacia afuera) la tuerca, lejos del soporte de suspensión Las ruedas de la cubierta, que son de forma esférica (50“ y 54” cubiertas delantera.
Page 61
(y la válvula de descarga hidrostática abierta) el freno necesita ajustes. Consulte con su distribuidor Cub Cadet para Lubrique todos los puntos de lubricación. realizar un ajuste del freno.
Page 62
Hay varios interruptores de seguridad en el sistema eléctrico. Si una No permita que las pinzas de los cables se toquen. función del sistema de bloqueo de seguridad descrito antes no funciona adecuadamente, haga que el distribuidor Cub Cadet revise el sistema eléctrico. Conecte el cable positivo ( ) al borne positivo ( ) de la batería...
Trabajando en el lado derecho del tractor, inserte una llave de Tire del pasador de chaveta hacia afuera de la varilla de elevación ajustar delantera de la plataforma que la sujeta a la plataforma. Consulte trinquete de 3⁄8” pulgadas para , en el orificio cuadrado de la Figura 7-4.
Page 64
Coloque un bloque de madera entre el deflector del alojamiento Pruebe el equilibrio de la cuchilla usando un compensador de de la plataforma y la cuchilla de corte para que actúe como cuchillas. Afile el metal del lado pesado hasta que quede bien estabilizador.
Page 65
Cambio de la correa de transmisión Para cambiar la correa de transmisión del tractor, se deben retirar varios componentes y se necesitan herramientas especiales. Solicite a su distribuidor Cub Cadet que realice el reemplazo de la correa de transmisión. Figura 7-9 NOTA: Use una llave de trinquete de ¹/2 de pulgada como se indica...
Page 66
Solución de Problemas Problema Causa Solución Vibración excesiva 1. Cuchilla de corte floja. 1. Apriete la cuchilla y el husillo. 2. Cuchilla de corte dañada, desbalanceada o 2. Reemplace la cuchilla. doblada. Corte desigual 1. La plataforma no está correctamente 1.
Page 70
DECLARACIÓN FEDERAL y/o DE CALIFORNIA SOBRE GARANTÍAS EN EL CONTROL DE EMISIONES SUS DERECHOS Y OBLIGACIONES EN CUANTO A LA GARANTÍA MTD Consumer Group Inc, la Agencia de Protección Medioambiental de los Estados Unidos (EPA), y para aquellos productos certificados para su venta en el estado de California, el Departamento de los Recursos del Aire de California (CARB) se complacen en explicar la garantía que evaporativo sistema de control de emisiones (ECS) de su equipo (equipos de exteriores) de encendido por chispa para todo terreno, pequeño, de exteriores del año 2014-2015.
Page 71
Durante la totalidad del período de garantía del motor y equipo para todo terreno arriba mencionado, MTD Consumer Group Inc mantendrá un suministro de piezas bajo garantía suficiente para satisfacer la demanda esperada de tales piezas. Cualquier pieza de reemplazo se podrá usar para el cumplimiento del mantenimiento o las reparaciones bajo garantía y se suministrarán sin cargo para el propietario.
Page 72
únicamente por el resto del período de garantía original. mencionado de garantía escrita expresa. Ninguna otra garantía expresa Chasis y eje delantero — Cub Cadet garantiza que el chasis y el eje de pivote excepto la mencionada anteriormente, extendida por personas físicas delantero de hierro forjado están libres de defectos en los materiales y la...