Knob 1 (Beat Stretch) Test; Display Of Test Results; Test End; Foot Sw Test - Yamaha RM1x Service Manual

Display Of Test Results

NG
05: Panel Switch
Push [MODE ]

Test End

After displaying the test result when the check
to the [TAP] switch end and the test will be
finished.
After Pressing the [F4] to exit the test, press the
[+1] switch to proceed with the next test and
then the [ENTER] switch to execute the next test.
Refer to " B PROCEEDING THROUGH THE
TESTS " if the " NG " occurs while testing.
C-6 ENCODER 1 [ F1 ] TEST
06: Encoder 1
RIGHT 00
Confirm the Encoder corresponding to the
switch are working properly from the left side.
When you rotate the Encoder clockwise according
to the LCD display, the value at the right of the
LCD simply increases from 0 to 30. When you
rotate the Encoder counterclockwise, the value
at the right of the LCD simply increases from 0
to 30. After that, confirm that the OK appears on
the LCD.
06: Encoder1
RIGHT xx
06: Encoder1
LEFT xx
(where xx= current ENCODER 1 value)
Display Of Test Results
OK
06: Encoder1
LEFT 00
NG Not appearing
Test End
After displaying the test result and the test will
be finished.
After Pressing the [F4] to exit the test, press the
[+1] switch to proceed with the next test and
then the [ENTER] switch to execute the next test.
Refer to " B PROCEEDING THROUGH THE
TESTS " if the " NG " occurs while testing.
C-7 ENCODER 2 [ F2 ] TEST
C-8 ENCODER 3 [ F3 ] TEST
C-9 ENCODER 4 [ F4 ] TEST
These tests can be performed in the same manner
as the test C-6, " ENCODER 1
NG
[F1]
OK
TEST " .
[F2]
C-10 KNOB 1 (BEAT STRETCH) TEST
10: Knob 1
xxx 64
(where xxx= current KNOB 1 value)
According to the target value displayed on the
LCD, slowly rotate the KNOB 1.
Check that the value changes from 64 to 128
then to 00 and back to 64 (in other words, center
to top then to bottom and back to center). After
that, confirm that the " OK " appears on the LCD.
10: Knob 1
xxx yyy
(where xxx= current KNOB 1 value and
yyy= target value)
Display Of Test Results
OK
10: Knob1
064 064
NG Not appearing
When the value of the display passes 64 after
64-128-00 and passes 64 , OK is displayed.
Test End
After displaying the test result and the test will
be finished.
After Pressing the [F4] to exit the test, press the
[+1] switch to proceed with the next test and
then the [ENTER] switch to execute the next test
Refer to " B PROCEEDING THROUGH THE
TESTS " if the " NG " occurs while testing.
C-11 KNOB 2 (CLOCK SHIFT) TEST
C-12 KNOB 3 (GATE TIME) TEST
C-13 KNOB 4 (VELOCITY) TEST
C-14 KNOB 5 (CUTOFF) TEST
C-15 KNOB 6 (RESONANCE) TEST
C-16 KNOB 7 (EG DECAY) TEST
C-17 KNOB 8 (PITCH BEND) TEST
These tests can be performed in the same
manner as the test ,
C-10
C-18 FOOT SW TEST
18: FOOT SW
0
Connect a foot switch and press it on and off.
Check that the display on the LCD changes
from off to on then back to off and verify that to
the " OK " result is displayed.
OK
" KNOB 1 (BEAT) TEST "
RM1x
29