Erbauer ERB900 Manual
  1. Manuals
  2. Brands
  3. Erbauer Manuals
  4. Power Tool
  5. ERB900
  6. Manual
Erbauer ERB900 Manual

Erbauer ERB900 Manual

Biscuit jointer
Hide thumbs
Table of Contents

Advertisement

Quick Links

WARRANTY
YEARS
ERB900
BISCUIT JOINTER

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ERB900 and is the answer not in the manual?

Questions and answers

Related Manuals for Erbauer ERB900

Summary of Contents for Erbauer ERB900

  • Page 1 WARRANTY YEARS ERB900 BISCUIT JOINTER...
  • Page 3 Congratulations on your purchase of a quality power tool from Screwfix Direct Ltd. This product should give you reliable service but for your peace of mind this power tool does carry a 24-month guarantee, the terms of which are detailed below. If this product develops a fault within the guarantee period contact Screwfix Direct Ltd on Freephone 0500 41 41 41.

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. SAVETHESE INSTRUCTIONS 1. Work area. a. Keep work area clean and well lit. Cluttered and dark areas invite accidents.

  • Page 5: Health Advice

    on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f.

  • Page 6: Double Insulation

    You are advised to consider the risks associated with the materials you are working with and to reduce the risk of exposure.You should: - Work in a well-ventilated area. -Work with approved safety equipment, such as those dust masks that are specially designed to filter microscopic particles.

  • Page 7: Important Note

    barriers between the electrical and mechanical components making it unnecessary for the tool to be earthed. Important note: Remove the main plug from socket before carrying out any adjustment or servicing. Ensure your mains supply voltage is the same as your tool rating plate voltage. SYMBOLS Read the manual Warning...
  • Page 8 � � � � � � � � �� �� �� �� � �� �� �� �� �� �� 1. AUXILIARY HANDLE 2. CLAMPING LEVER FOR ANGLE ADJUSTMENT 3. CLAMPING LEVER FOR HEIGHT ADJUSTMENT 4. FENCE 5. KNOB FOR ADJUSTING HEIGHT...

  • Page 9: Technical Data

    6. ANGLE INDICATOR 7. BASE PLATE 8. LOCK KNOB FOR BLADE COVER 9. ON/OFF SWITCH 10. MAIN HANDLE 11. DUST ADAPTOR 12. STOP PIN FOR CUTTING DEPTH 13. SPINDLE LOCKING BUTTON 14. ADJUSTING KNOB FOR CUTTING DEPTH 15. DUST BAG 16.

  • Page 10: Adjusting The Cutting Depth

    OPERATION INSTRUCTIONS 1. ADJUSTING THE CUTTING DEPTH Marking Thickness of material Biscuit dowel Cutting depth 8-12mm No.0 8.0mm 12-15mm No.10 10.0mm >15mm No.20 12.3mm simplex 13.0mm duplex 14.7mm Max. 18.0mm Move the motor base as far as possible backward. Set the cutting depth by turning the cutting depth adjustment knob.
  • Page 11 procedure! Tighten Loosen Remove the outer flange from the spindle using the spanner supplied. Position the saw blade on the inner flange. Place the outer flange on the Spindle and tighten it fully with the spanner. Take care that the outer flange is placed with the correct side to the spindle Release the spindle lock and check that the spindle is unlocked by rotating it.
  • Page 12 SMALL WORKPIECE Place the machine near the workpieces. The side of the machine must be facing the side of the workpiece. WORKPIECES THINNER THAN 16 MM Place the machine near the workpiece. Place the adjustment plate on the angle stop. Take care for setting the height, the groove for the biscuit dowel must be in the middle of the workpiece.

  • Page 13: Setting The Cutting Depth

    12. SETTING THE CUTTING DEPTH When the cutting depth is not correct, it can be adjusted as follows: Move the motor base as far as possible backwards. Set the cutting depth by turning the knob(14) , the knob is positioned at the back of the pin. Repeat the procedure till the cutting depth is correct.

  • Page 14: Plug Replacement

    PLUG REPLACEMENT The fuse in the main plug of your power tool should always be replaced with one of identical rating. Check the voltage given on your power tool matches the supply voltage. The power tool is supplied with a fitted plug, however if you should need to fit a new plug follows the instruction below.

  • Page 15: Declaration Of Conformity

    Yeovil BA 22 8RT Declare that the product BISCUIT JOINTER ERB900 Complies with the essential health and safety requirements of the following directives: 89/336 EEC, 93/68 EEC – EMC Directive. 73/23 EEC, 93/68 EEC – Low Voltage Directive 98/37 EC – Machinery Directive.

Table of Contents