Troubleshooting - Hoover POWER SCRUB Owner's Manual
Carpet washer
Hide thumbs
Also See for POWER SCRUB:
- User manual ,
- Owner's manual (20 pages) ,
- Owner's manual (19 pages)
Table of Contents
Advertisement
Available languages
Available languages
TROUBLESHOOTING
If a minor problem occurs, it usually can be solved quite easily when the cause is found by using the
checklist below.
Any other servicing should be done by an authorized service representative.
If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take
it to a service center prior to continuing use.
WARNING
!
To reduce risk of personal injury - Unplug before cleaning or servicing.
PROBLEM
POSSIBLE CAUSE
Cleaner won't run. 1. Not firmly plugged in.
2. No voltage in wall plug.
3. Blown fuse or tripped
breaker.
4. Fuse in cleaner blown.
Low suction.
1. Dirty Water Tank full/
automatic shut off engaged.
2. Blockage In tool on end of
hose.
3. Dirty Water Tank lid not on
correctly.
4. Dirty Water Tank Debris Filter
Clogged.
5. Blockage in nozzle.
6. Recovery Tank not properly
secured.
Hose nozzle stops
1. Clean Water Tank or
spraying liquid
Detergent Container is empty.
during use.
Hose nozzle will
1. Air is trapped in the pump
not spray after
and hose.
filling the Clean
Water Tank or
Detergent Con-
tainer.
Hose nozzle will
1. Pump is defective.
not spray after
priming pump.
Clean water won't
1. Clean Water Tank not firmly
dispense.
in place.
2. Clean Water Tank or solution
container empty.
Solution won't
1. Mode knob is in "Rinse
dispense
Mode".
Brushes won't
1. Dirty filter screen on front of
rotate during floor
unit behind nozzle.
cleaning.
!
POSSIBLE SOLUTION
1. Plug unit in firmly.
2. Check fuse or breaker in home.
3. Replace fuse or reset breaker in home.
4. Take to service center.
1.Remove and empty Dirty Water Tank. See
"How to Empty" page 9.
2. Remove tool and clear blockage.
3. Make sure lid is on securely. See "How to
Use" on page 9.
4. See "How to Clean" page 5.
5. See "How to Clean" page 15.
6. Replace Recovoery Tank as per instructions
on page 9.
1. Turn off cleaner and fill Clean Water Tank
and Detergent Container.
1. Turn on the cleaner. If hose does not spray,
prime the pump by lowering the hose down to
the floor and hold the trigger for up to 1 minute.
1. Call for service: 1-800-944-9200
1. Make sure tank is securely locked in
position.
2. Refill container according to instructions for
surface being cleaned.
1. Turn Knob to "Wash".
1. Clean screen.
Actual model may vary from images shown.
17
Hide quick links:
Advertisement
Chapters
Table of Contents
Need help?
Do you have a question about the POWER SCRUB and is the answer not in the manual?
Questions and answers
how to remove brushes on model fh50134
To remove the brushes on the Hoover Power Scrub model FH50134, follow these steps:
1. Align the post of the brush block with the hole on the base of the unit.
2. Press firmly on the brush block to release it from its position.
3. Ensure the brushes turn freely before reinstallation.
If reattaching, align the post with the hole, press firmly until the brushes click into place.
This answer is automatically generated
I'm not real sure how to connect the hose up when I do I get no water to spray.and no suction
To connect the hose on a Hoover Power Scrub and ensure water sprays and suction works:
1. Ensure the hose connector is firmly attached to the hose solution port.
2. Open the Accessory Hose Suction Port and insert the hose end, aligning the indicator.
3. Secure the hose in place to prevent leaks or disconnection.
4. Prime the hose by holding down the hose trigger until it begins spraying water.
5. Check that the hose port door is completely shut for proper suction.
6. Turn on the Power Scrub, tilt the handle back, and squeeze the trigger to prime the pump for about 30 seconds to remove trapped air.
Following these steps ensures proper water flow and suction.
This answer is automatically generated
Cleaner won't **** up the water
The Hoover Power Scrub Carpet Cleaner may not be picking up water due to several possible reasons:
1. Dirty Water Tank Full – If the tank is full, empty it and reattach it securely.
2. Dirty Water Tank Lid Not Sealed – Ensure the lid is properly latched and sealed. Clean any debris before reattaching.
3. Nozzle Blockage – Check the nozzle for clogs, remove it, and rinse under running water.
4. Solution Tube Disconnected – Ensure the solution tube is properly connected.
5. Brushes Not Rotating – If brushes are not moving, clean them to remove debris or tangled hair.
Following these troubleshooting steps can help restore proper suction.
This answer is automatically generated
The cleaner sprays but will not **** up the water. I've checked underside and cleaned all of the parts.
Hello and ty for your help. My Hoover vacuum cleaner is not releasing water mixed with vacuum cleaning liquid? Tried to squeeze the button and move/ advance the các cleaner forward slowly? Very grateful,
Your Hoover Power Scrub may not be releasing water mixed with cleaning liquid due to the following possible reasons:
1. Clean Water Tank Not Secure – Ensure the clean water tank is firmly locked in place.
2. Mode Knob in "Rinse" Mode – Turn the mode knob to "Wash" to allow solution dispensing.
3. Pump Not Primed – Hold the trigger for up to 1 minute to prime the pump.
4. Obstruction or Faulty Linkage – If the button does not engage properly, inspect the linkage mechanism and consider adding a small spacer to improve contact.
5. Internal Component Issues – If leaking or other mechanical issues are present, disassemble and inspect internal parts for blockages or misalignment.
Check these steps to resolve the issue.
This answer is automatically generated
I fill the fill tank to the line with the right amount of carpet shampoo and the dirty water tank only fills up halfway before it shuts down when I **** shampooing my carpet . What is the problem
The Hoover POWER SCRUB may shut down when the dirty water tank is only halfway full due to the automatic shut-off feature. The yellow float disk inside the dirty water tank rises as water fills the tank. If it gets stuck or moves too early, it can trigger the suction shut-off prematurely. To fix this, check if the float disk is moving freely and ensure the tank is properly positioned. Also, inspect the clean water/solution tank, as it may need refilling.
This answer is automatically generated
I want to rinse and dry carpet only, any help?
If not that, just use as wet vac, can it do that?
To rinse and dry the carpet using the Hoover Power Scrub:
1. Set to Rinse Mode: Adjust the Wash/Rinse Selector to "Rinse."
2. Rinse the Carpet: Move the cleaner forward and backward over the carpet, following the same steps as washing.
3. Use Dry Strokes: Keep the nozzle flat on the floor and perform additional dry strokes to aid in drying.
4. Repeat if Necessary: For heavily soiled areas, repeat the process but avoid over-saturating the carpet.
5. Monitor Dirty Water Tank: Empty the tank when the motor sound becomes higher pitched or suction decreases.
6. Allow Carpet to Dry: Keep children and pets away until the carpet is completely dry. If walking on damp carpet is necessary, place towels or white cloths on high-traffic areas.
This answer is automatically generated
What cleaning solution do I use?
The recommended cleaning solution for the Hoover Power Scrub is a Hoover® solution.
This answer is automatically generated
Fresh water tank leaks as soon as attaching to the machine
The fresh water tank leaks when attached to the Hoover Power Scrub because it may not be securing properly into the machine. Users report that the tank is loose, wobbly, and does not click into place, which can cause water and solution to pour out when the unit is turned or moved.
This answer is automatically generated
Leaking from bottom