Do you have a question about the POWER SCRUB and is the answer not in the manual?
Questions and answers
al haeberle
January 19, 2025
how to remove brushes on model fh50134
1 comments:
Mr. Anderson
February 4, 2025
To remove the brushes on the Hoover Power Scrub model FH50134, follow these steps:
1. Align the post of the brush block with the hole on the base of the unit. 2. Press firmly on the brush block to release it from its position. 3. Ensure the brushes turn freely before reinstallation.
If reattaching, align the post with the hole, press firmly until the brushes click into place.
This answer is automatically generated
Darla Eggert
February 21, 2025
I'm not real sure how to connect the hose up when I do I get no water to spray.and no suction
1 comments:
Mr. Anderson
February 21, 2025
To connect the hose on a Hoover Power Scrub and ensure water sprays and suction works:
1. Ensure the hose connector is firmly attached to the hose solution port. 2. Open the Accessory Hose Suction Port and insert the hose end, aligning the indicator. 3. Secure the hose in place to prevent leaks or disconnection. 4. Prime the hose by holding down the hose trigger until it begins spraying water. 5. Check that the hose port door is completely shut for proper suction. 6. Turn on the Power Scrub, tilt the handle back, and squeeze the trigger to prime the pump for about 30 seconds to remove trapped air.
Following these steps ensures proper water flow and suction.
This answer is automatically generated
Cindy
February 26, 2025
Cleaner won't **** up the water
2 comments:
Mr. Anderson
February 26, 2025
The Hoover Power Scrub Carpet Cleaner may not be picking up water due to several possible reasons:
1. Dirty Water Tank Full – If the tank is full, empty it and reattach it securely. 2. Dirty Water Tank Lid Not Sealed – Ensure the lid is properly latched and sealed. Clean any debris before reattaching. 3. Nozzle Blockage – Check the nozzle for clogs, remove it, and rinse under running water. 4. Solution Tube Disconnected – Ensure the solution tube is properly connected. 5. Brushes Not Rotating – If brushes are not moving, clean them to remove debris or tangled hair.
Following these troubleshooting steps can help restore proper suction.
This answer is automatically generated
Cindy
February 26, 2025
The cleaner sprays but will not **** up the water. I've checked underside and cleaned all of the parts.
Charles
February 28, 2025
Hello and ty for your help.
My Hoover vacuum cleaner is not releasing water mixed with vacuum cleaning liquid? Tried to squeeze the button and move/ advance the các cleaner forward slowly? Very grateful,
1 comments:
Mr. Anderson
February 28, 2025
Your Hoover Power Scrub may not be releasing water mixed with cleaning liquid due to the following possible reasons:
1. Clean Water Tank Not Secure – Ensure the clean water tank is firmly locked in place. 2. Mode Knob in "Rinse" Mode – Turn the mode knob to "Wash" to allow solution dispensing. 3. Pump Not Primed – Hold the trigger for up to 1 minute to prime the pump. 4. Obstruction or Faulty Linkage – If the button does not engage properly, inspect the linkage mechanism and consider adding a small spacer to improve contact. 5. Internal Component Issues – If leaking or other mechanical issues are present, disassemble and inspect internal parts for blockages or misalignment.
Check these steps to resolve the issue.
This answer is automatically generated
Robin M Nesland
March 11, 2025
I fill the fill tank to the line with the right amount of carpet shampoo and the dirty water tank only fills up halfway before it shuts down when I **** shampooing my carpet . What is the problem
1 comments:
Mr. Anderson
March 11, 2025
The Hoover POWER SCRUB may shut down when the dirty water tank is only halfway full due to the automatic shut-off feature. The yellow float disk inside the dirty water tank rises as water fills the tank. If it gets stuck or moves too early, it can trigger the suction shut-off prematurely. To fix this, check if the float disk is moving freely and ensure the tank is properly positioned. Also, inspect the clean water/solution tank, as it may need refilling.
This answer is automatically generated
Iggy wozniak
March 23, 2025
I want to rinse and dry carpet only, any help?
2 comments:
Iggy wozniak
March 23, 2025
If not that, just use as wet vac, can it do that?
Mr. Anderson
March 23, 2025
To rinse and dry the carpet using the Hoover Power Scrub:
1. Set to Rinse Mode: Adjust the Wash/Rinse Selector to "Rinse." 2. Rinse the Carpet: Move the cleaner forward and backward over the carpet, following the same steps as washing. 3. Use Dry Strokes: Keep the nozzle flat on the floor and perform additional dry strokes to aid in drying. 4. Repeat if Necessary: For heavily soiled areas, repeat the process but avoid over-saturating the carpet. 5. Monitor Dirty Water Tank: Empty the tank when the motor sound becomes higher pitched or suction decreases. 6. Allow Carpet to Dry: Keep children and pets away until the carpet is completely dry. If walking on damp carpet is necessary, place towels or white cloths on high-traffic areas.
This answer is automatically generated
Susan Jackson
April 3, 2025
What cleaning solution do I use?
1 comments:
Mr. Anderson
April 3, 2025
The recommended cleaning solution for the Hoover Power Scrub is a Hoover® solution.
This answer is automatically generated
Jan
April 13, 2025
Fresh water tank leaks as soon as attaching to the machine
1 comments:
Mr. Anderson
April 13, 2025
The fresh water tank leaks when attached to the Hoover Power Scrub because it may not be securing properly into the machine. Users report that the tank is loose, wobbly, and does not click into place, which can cause water and solution to pour out when the unit is turned or moved.
Page 1
Operating and Servicing Instructions Español - página E ⁄ Frances - pag F www.hoover.com Please visit Hoover.com for video instructions for this cleaner. IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE. Questions or concerns? For assistance, please call Customer Service at 1-800-944-9200 Mon-Fri 8am-7pm EST before returning this product to the store.
Warranty ........................19 If you need assistance: Visit our website at hoover.com for more information or for video instruction fot this carpet washer. Follow the authorized dealer locator link to find the Hoover authorized dealer nearest you or call 1-800- ®...
• Operate cleaner only at voltage specified on data plate on lower handle of cleaner. • Do not leave appliance when plugged in. Unplug from outlet when not in use and before cleaning or servicing. • Use indoors only. • Do not immerse. Use only on carpet moistened by cleaning process. • Use only HOOVER cleaning products intended for use with this machine. (See ® the “Cleaning Products” section of this manual.) • Do not allow to be used as a toy. Not intended for use by children age 12 and under. Close supervision is necessary when used near children. To avoid injury or damage, keep children away from product, and do not allow children to place fingers or other objects into any openings.
CAUTION - TO REDUCE THE RISK OF DAMAGE: • Avoid picking up hard, sharp objects with this product, as they may cause damage. • Store appropriately indoors in a dry place. Do not expose machine to freezing temperatures. • Do not use sharp objects to clean out hose as they can cause damage. • To assist in reducing drying time, be certain the area is well ventilated when using detergents and other cleaners with this machine. • To help prevent matting and resoiling, avoid contact with carpets until they are dry. Keep children and pets away from carpets until they are completely dry. • Do not store extractor with solution in tanks. • With brushes on, do not allow cleaner to sit in one location for an extended period of time, as damage to the floor can result.
REMOVE ALL PARTS FROM CARTON AND IDENTIFY EACH ITEM SHOWN. MAKE SURE ALL PARTS ARE LOCATED BEFORE DISPOSING OF PACKING MATERIALS. *Available on select models only. Accessories not included with your model may be purchased separately by visiting hoover.com. A. Carpet Washer Tools Included in Mesh Bag B.
HOW TO ASSEMBLE NOTE: PHILLIPS SCREWDRIVER NEEDED FOR ASSEMBLY. STORE TOOLS ATTACH HANDLE 1. Position upper handle and slide down into carpet 6. Place tools and hose into Mesh Tool Storage washer base (Fig. 2) bag provided. 2. Insert both screws and tighten with screwdriver 7.
FEATURES BACK FRONT LIST OF FEATURES 1. Solution Trigger: Press to release 8. Nozzle cleaning solution 9. Accessory Hose Connection Port 2. ON/OFF Pedal 10. Cord Storage Hook 3. Wash/Rinse Selector 11. Cord Storage Hook 4. Clean Water/Solution Tank (Does not rotate) 5.
Do not fill with water above 140°F (60°C). for use with this machine. (See the “Cleaning Solutions” section in this manual for details) They 4. Fill Solution Tank (Fig. 19) with Hoover ® are specially formulated for use with your cleaner.
DIRTY WATER TANK The Dirty Water Tank holds the dirty water that is picked up from the surface being cleaned. When the Dirty Water Tank is full, the automatic shut-off will engage, suction will stop and the tank must be emptied (see Automatic Shut-Off section). How to Empty 1.
BEFORE YOU BEGIN CLEANING 4. When cleaning entire floor, move furniture out of area to be cleaned (may not be necessary if only 1. Vacuum thoroughly - For carpet, use a HOOVER ® high traffic areas are to be cleaned). For furniture vacuum cleaner with an agitator for best results.
Page 11
4 times = 2 while squeezing the trigger and 2 without). NOTE: For best results, use straight, parallel 10. For best cleaning results, Hoover recommends strokes. Overlap strokes by 1 inch to help prevent to rinse the carpet with water only. This will streaking.
TOOLS CONNECT HOSE FOR TOOL USE CAUTION Always turn off appliance before connecting or disconnecting hose. How to Attach 1. Open Accessory Hose Suction Port (A, Fig. 31). Insert hose end, aligning the indicator with the unlock arrows. 2. Rotate clockwise to lock position (B, Fig. 31). 3.
Page 13
3. Place handle in upright position. SpinScrub brushes will not rotate while handle is in upright position. 4. Fill Clean Water Tank according to instructions. 5. Fill Solution Tank with HOOVER solution ® according to instructions. 6. Attach tool to end of hose.
CLEANING UPHOLSTERY Read “Before You Begin Cleaning” instructions. Be sure to check Hoover Cleaning Guide on page 10 and the cleaning code on your upholstery. Use your cleaner only on upholstery marked “W” or “W/S”. 1. Attach hose and solution tube as instructed.
MAINTENANCE Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure continued cleaning effectiveness. Any other servicing should be done by an authorized service representative. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a service center prior to continuing use.
Warranty Service Dealer (Depot) by: • Checking the Yellow Pages under “Vacuum Cleaners” or “Household”. • Visit our website at hoover.com (U.S. Customers) or hoover.ca (Canadian customers). Follow the service center link to find the service outlet nearest you. • For an automated referral of authorized service outlet locations call 1-800-944-9200.
TROUBLESHOOTING If a minor problem occurs, it usually can be solved quite easily when the cause is found by using the checklist below. Any other servicing should be done by an authorized service representative. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a service center prior to continuing use.
CLEANING SOLUTIONS WARNING: To reduce the risk of fire and electric shock due to internal component damage, use only Hoover cleaning products intended for use with the appliance as noted below. ® Hoover Cleaning Solution Guide or optimal performance use Hoover brand Clean...
United States, including its full two year from date of purchase (the “Warranty territories and possessions, outside a U.S. Military Period”). During the Warranty Period, Hoover will ® Exchange and outside of Canada. This warranty...
Si este producto no se ajusta a las condiciones Período de Garantía no se prorrogará en función garantizadas, llévelo a un Concesionario autor- de ningún reemplazo o reparación realizados en izado de servicio de garantía de Hoover junto ® virtud de esta Garantía.
Page 22
ADVERTENCIA: Para reducir el riesgo de incendio y descarga eléctrica debido a da os de los componentes en los espacios provistos. internos, use nicamente productos de limpieza de Hoover y accesorios para suelos duros dise ados para 1-800-944-9200 uso con este aparato (véase abajo).
• Visite nuestro sitio web en hoover.com (clientes incluyendo las siguientes: estadounidenses) o hoover.ca (clientes canadienses). Siga el enlace del centro de servicio para LEA TODAS LAS INSTRUCCIONES ANTES DE USAR ESTE APARATO encontrar el centro de servicio más cercano.
Page 24
• No limpie las partes del piso en las que haya tomacorrientes. SOLUCIÓN DE PROBLEMAS • No aspire ningún objeto que se esté quemando o que libere humo, como cigarrillos, fósforos o cenizas calientes. Si ocurre un problema menor, generalmente puede resolverse con bastante facilidad cuando se • No use sin filtros y tanques. halla la causa, usando esta lista de verificación. • ADVERTENCIA: Este producto contiene sustancias químicas reconocidas por el esta- Cualquier otra tarea de mantenimiento debe ser realizada por un representante de mantenimiento autorizado. do de California como causantes de cáncer, defectos congénitos o daño reproductivo.
*Disponible sólo en algunos modelos. Los accesorios no incluidos con su modelo pueden comprarse por cojinete del motor. aire. separado, visitando www.hoover.com. • Verifique que la puerta de la tapa y el émbolo del depósito se mueven libremente. Deje secar al aire los cepillos y la parte de...
ENSAMBLADO DE LA ASPIRADORA MANTENIMIENTO NOTA: SE NECESITA UN DESTORNILLADOR PHILLIPS PARA EL ENSAMBLADO Familiarícese con estas tareas de mantenimiento en el hogar, ya que el uso y cuidado apropiados de su aspiradora asegurarán una limpieza continuamente eficaz. GUARDE LOS ACCESORIOS PARA COLOCAR EL MANGO Cualquier otra tarea de mantenimiento debe ser realizada por un representante de mantenimiento autorizado.
Lea las instrucciones “Antes de comenzar a limpiar” que se encuentran. Asegúrese de consultar la guía de limpieza de Hoover en la página 10 y el código de limpieza de su tapizado. Utilice la limpiadora únicamente en tapizado marcado con “W” o “W/S”.
11. Coloque el accesorio contra la parte vertical ® solución Hoover® Clean Plus 2X o con cualquier 15 y “Después de usar el accesorio” que máquina y anular la garantía. del escalón y presiónelo levemente en el pelo de otro detergente de Hoover (consulte la página...
TANQUE DE RECUPERACIÓN ACCESORIOS El tanque de agua sucia contiene el agua sucia que se recoge desde la superficie que se está limpiando. PARA CONECTAR LA MANGUERA Cuando el tanque de agua sucia está lleno, se activará el cierre automático, se detendrá la succión y se PRECAUCIÓN deberá...
1. Llene el tanque de agua limpia de acuerdo con las instrucciones (página 8). DESPUÉS DEL USO IMPORTANTE 2. Llene el recipiente de solución con solución Hoover® de acuerdo con las Deje secar la alfombra o el tapizado. Para ayudar a instrucciones (página 8).
Need help?
Do you have a question about the POWER SCRUB and is the answer not in the manual?
Questions and answers
how to remove brushes on model fh50134
To remove the brushes on the Hoover Power Scrub model FH50134, follow these steps:
1. Align the post of the brush block with the hole on the base of the unit.
2. Press firmly on the brush block to release it from its position.
3. Ensure the brushes turn freely before reinstallation.
If reattaching, align the post with the hole, press firmly until the brushes click into place.
This answer is automatically generated
I'm not real sure how to connect the hose up when I do I get no water to spray.and no suction
To connect the hose on a Hoover Power Scrub and ensure water sprays and suction works:
1. Ensure the hose connector is firmly attached to the hose solution port.
2. Open the Accessory Hose Suction Port and insert the hose end, aligning the indicator.
3. Secure the hose in place to prevent leaks or disconnection.
4. Prime the hose by holding down the hose trigger until it begins spraying water.
5. Check that the hose port door is completely shut for proper suction.
6. Turn on the Power Scrub, tilt the handle back, and squeeze the trigger to prime the pump for about 30 seconds to remove trapped air.
Following these steps ensures proper water flow and suction.
This answer is automatically generated
Cleaner won't **** up the water
The Hoover Power Scrub Carpet Cleaner may not be picking up water due to several possible reasons:
1. Dirty Water Tank Full – If the tank is full, empty it and reattach it securely.
2. Dirty Water Tank Lid Not Sealed – Ensure the lid is properly latched and sealed. Clean any debris before reattaching.
3. Nozzle Blockage – Check the nozzle for clogs, remove it, and rinse under running water.
4. Solution Tube Disconnected – Ensure the solution tube is properly connected.
5. Brushes Not Rotating – If brushes are not moving, clean them to remove debris or tangled hair.
Following these troubleshooting steps can help restore proper suction.
This answer is automatically generated
The cleaner sprays but will not **** up the water. I've checked underside and cleaned all of the parts.
Hello and ty for your help. My Hoover vacuum cleaner is not releasing water mixed with vacuum cleaning liquid? Tried to squeeze the button and move/ advance the các cleaner forward slowly? Very grateful,
Your Hoover Power Scrub may not be releasing water mixed with cleaning liquid due to the following possible reasons:
1. Clean Water Tank Not Secure – Ensure the clean water tank is firmly locked in place.
2. Mode Knob in "Rinse" Mode – Turn the mode knob to "Wash" to allow solution dispensing.
3. Pump Not Primed – Hold the trigger for up to 1 minute to prime the pump.
4. Obstruction or Faulty Linkage – If the button does not engage properly, inspect the linkage mechanism and consider adding a small spacer to improve contact.
5. Internal Component Issues – If leaking or other mechanical issues are present, disassemble and inspect internal parts for blockages or misalignment.
Check these steps to resolve the issue.
This answer is automatically generated
I fill the fill tank to the line with the right amount of carpet shampoo and the dirty water tank only fills up halfway before it shuts down when I **** shampooing my carpet . What is the problem
The Hoover POWER SCRUB may shut down when the dirty water tank is only halfway full due to the automatic shut-off feature. The yellow float disk inside the dirty water tank rises as water fills the tank. If it gets stuck or moves too early, it can trigger the suction shut-off prematurely. To fix this, check if the float disk is moving freely and ensure the tank is properly positioned. Also, inspect the clean water/solution tank, as it may need refilling.
This answer is automatically generated
I want to rinse and dry carpet only, any help?
If not that, just use as wet vac, can it do that?
To rinse and dry the carpet using the Hoover Power Scrub:
1. Set to Rinse Mode: Adjust the Wash/Rinse Selector to "Rinse."
2. Rinse the Carpet: Move the cleaner forward and backward over the carpet, following the same steps as washing.
3. Use Dry Strokes: Keep the nozzle flat on the floor and perform additional dry strokes to aid in drying.
4. Repeat if Necessary: For heavily soiled areas, repeat the process but avoid over-saturating the carpet.
5. Monitor Dirty Water Tank: Empty the tank when the motor sound becomes higher pitched or suction decreases.
6. Allow Carpet to Dry: Keep children and pets away until the carpet is completely dry. If walking on damp carpet is necessary, place towels or white cloths on high-traffic areas.
This answer is automatically generated
What cleaning solution do I use?
The recommended cleaning solution for the Hoover Power Scrub is a Hoover® solution.
This answer is automatically generated
Fresh water tank leaks as soon as attaching to the machine
The fresh water tank leaks when attached to the Hoover Power Scrub because it may not be securing properly into the machine. Users report that the tank is loose, wobbly, and does not click into place, which can cause water and solution to pour out when the unit is turned or moved.
This answer is automatically generated
Leaking from bottom