Advertisement
3
Press PRESET + or – to select the preset number,
Operating an iPhone
then press DISPLAY/MEMORY.
Example: The following displays appear when you preset FM
1
Set the iPhone on the Dock connector.
89.8 MHz to preset number 2 for FM.
The Dock connector can be tilted slightly.
For details, see "Using an iPhone with the unit. "
2
Press .
"iPhone" appears in the display.
The iPhone begins to play back.
If the iPhone does not start playing back, operate directly on
the iPhone.
You can operate the connected iPhone via this unit or the
iPhone itself.
3
Adjust the volume using VOL + or –.
To operate from a remote
control
Aim the remote at the
(Remote sensor) of the unit.
(Play/Pause)
Start playing the iPhone. Press again to pause/resume playback.
(Forward)
Go to the next track.
Press and hold while listening to the sound to locate a
The display shows the frequency for about
desired point.
10 seconds, then returns to the current time.
(Backward)
Tips
Go back to the previous track. During playback, this
To preset another station, repeat these steps.
operation returns to the beginning of the current track. To
To cancel the preset number setting, press OFF instead of
go back to the previous track, press twice.
DISPLAY/MEMORY in step 3.
Press and hold while listening to the sound to locate a
Note
desired point.
If you store another station with the same preset number, the
MENU
previously stored station will be replaced.
Go back to the previous menu.
(Up)/ (Down)
To tune in to a preset station
Select a menu item or track for playback.
ENTER
1
Follow steps 1 to 2 in "Manual tuning" and
Execute the selected menu item or begin playback.
select the AM or FM band.
2
Press CLOCK/MODE repeatedly to select
Notes
If a pop-up message appears in the display of the iPod touch
"PRESET. "
or iPhone, see "About App. "
When using the remote to operate the unit, you can skip this
Some operations may differ or may not be available on some
step, and directly operate step 3.
models of iPhone.
3
Press PRESET + or – to select the desired
If the iPhone is already playing when set on the unit, the
sound from the iPhone will be output from the unit speaker,
preset number.
even if the unit was playing sound from another function.
4
Adjust the volume using VOL + or –.
If the battery of the iPhone is extremely low, charge it for a
while before operation.
Sony cannot accept responsibility in the event that data
–Auto preset tuning
recorded to an iPhone is lost or damaged when using the
iPhone connected to this unit.
1
Follow steps 1 to 2 in "Manual tuning" and
For details of environmental conditions for operating an
iPhone, check the website of Apple Inc.
select the AM or FM band.
MENU, (Up), (Down), and ENTER button on the main unit
2
Press and hold FM/AM until "AP" flashes in the
and/or on the supplied remote control will only work with the
Apple devices (iPhone/iPod touch) installed up to iOS 6. It will
display.
not work with iOS 7 or later. In such case, please operate on
3
Press DISPLAY/MEMORY.
the screen of Apple devices directly.
The unit automatically presets the available stations in order.
Operating the radio
Tip
To stop auto preset tuning, press FM/AM.
–Manual tuning
To switch the display when listening to
1
Press FM/AM to turn on the radio.
radio
2
Press FM/AM repeatedly to select the desired band.
When listening to radio, press DISPLAY/MEMORY repeatedly to
Each time you press the button, the radio band toggles
show the preset number, the frequency of the current station,
between AM and FM as follows:
the date and month, then the year. The display then returns to
the current time.
Note
3
When listening to a station which has not been preset, no
Press CLOCK/MODE repeatedly to select "TUNING. "
preset number will be displayed.
When using the remote to operate the unit, you can skip this
step, and directly operate step 4.
To improve reception
4
Press TUNE + or – repeatedly to tune to the
FM: Extend the FM wire aerial fully to increase reception
desired station.
sensitivity.
5
Adjust the volume using VOL + or –.
AM: Connect the supplied AM loop aerial to the unit. Rotate the
To turn off the radio, press OFF.
aerial horizontally for optimum reception.
Note
Notes on radio reception
When the FM frequency step is 0.05 MHz, the frequency
Do not place the AM loop aerial near the unit, power supply or
display is accurate to within 0.1 MHz. For example, 88.00 MHz
other AV equipment during use, as noise may result.
or 88.05 MHz will be displayed as "88.0 MHz. " In this case, press
Keep digital music players or mobile phones away from the
TUNE + or - once to change the frequency step, twice to
AM loop aerial or the FM aerial, as this may lead to reception
change the frequency display.
interference.
When you are listening to the radio with an iPhone connected
–Scan tuning
to the unit, interference with radio reception may occur.
When you are listening to the radio while charging an iPhone,
The unit automatically scans for AM or FM stations.
interference with radio reception may occur.
1
Follow steps 1 to 3 in "Manual tuning. "
Setting the alarm
2
Press and hold TUNE + or –.
+ : scans upward through the frequency bands.
– : scans downwards through the frequency bands.
This unit is equipped with 3 alarm modes—iPhone, radio and
Scanning starts from the currently-tuned frequency. When a
buzzer. Set the clock to the current time before setting the alarm,
station is received, scanning stops.
so that the alarm will sound at the correct time. (See "To set the
clock for the first time. " )
3
Adjust the volume using VOL + or –.
To set the alarm
–Preset tuning
1
Press and hold ALARM A or B.
You can preset up to 20 FM stations and 10 AM stations.
"WAKE UP" appears and the hour flashes in the display.
To preset a station
2
Press ALARM TIME SET + or – repeatedly until
1
Follow steps 1 to 5 in "Manual tuning" and
the desired hour appears.
To cycle the hour rapidly, press and hold ALARM TIME SET
manually tune into the station you wish to preset.
+ or –.
2
Press and hold DISPLAY/MEMORY for at least
3
Press ALARM A or B.
2 seconds.
The minute flashes.
4
Repeat step 2 to set the minute.
5
Press ALARM A or B.
The days of the week flash.
6
Repeat step 2 to set the days of the week.
You can select the days from the following three options by
pressing ALARM TIME SET + or –:
Week day: MON TUE WED THU FRI
Weekend: SAT SUN
Every day: MON TUE WED THU FRI SAT SUN
7
Press ALARM A or B.
The alarm mode setting is entered.
8
Press ALARM TIME SET + or – repeatedly until
the desired alarm mode flashes.
You can choose one of 4 settings: "iPhone, " "FM, " "AM" or
"BUZZER. " Set the alarm mode as follows:
– iPhone: see " To set the alarm as iPhone. "
– FM or AM: see " To set the radio alarm. "
– BUZZER: see " To set the buzzer alarm. "
Notes on the alarm in the event of a power
To set the alarm as iPhone
interruption
1
Perform steps 1 to 8 in "To set the alarm. "
In the event of a power interruption, the buzzer alarm will last
2
Press ALARM A or B to select alarm mode for
about 5 minutes if the battery is not weak. However, certain
functions will be affected as follows:
"iPhone. "
The backlight will not light up.
The volume level flashes in the display.
If the alarm mode is set to iPhone or radio, it will change to
3
buzzer automatically.
Press ALARM TIME SET + or – to adjust the
If OFF on the unit is not pressed, the alarm will sound for
volume.
about 5 minutes.
If "" appears in the display, the alarm will not sound in the
4
Press ALARM A or B.
event of a power interruption. Replace the battery if ""
The setting is entered. "A" or "B" appears in the display
appears.
indicating that the alarm has been activated.
The snooze function cannot be set during a power
The iPhone will sound at the set time.
interruption.
During a power interruption, each alarm will sound at the set
Notes
time only once.
To wake up to music stored in an iPhone, connect the iPhone
to the unit before the alarm sounds.
Setting the sleep timer
Even if the alarm setting for iPhone is complete, if you turn the
iPhone power off after setting the iPhone on the unit, the
alarm will be the buzzer.
You can fall asleep to music, etc. using the sleep timer. The unit
stops playback or radio automatically after a preset duration.
To set the radio alarm
1
Press SLEEP while playing music or listening to
1
Perform steps 1 to 8 in "To set the alarm. "
radio.
2
Press ALARM A or B to select radio band ("FM"
"SLEEP" appears and the sleep time flashes in the display.
2
Press SLEEP to set the sleep timer duration.
or "AM").
Each time you press SLEEP, the duration (in minutes)
Preset number flashes in the display.
changes as follows:
3
Press ALARM TIME SET + or – to select the
desired preset number or "– –" of the
corresponding band.
The display returns to the current time for about
"– –" is the last station you listened to before the alarm
4 seconds after you have finished the duration setting and
sounds.
released SLEEP, then the sleep timer starts.
4
Press ALARM A or B.
The unit plays for the duration you set, then stops.
The volume level flashes in the display.
Note
5
Press ALARM TIME SET + or – to adjust the
Any currently-playing optional component connected to the
volume.
AUDIO IN jack will continue playing back, although its sound
will be muted.
6
Press ALARM A or B.
The setting is entered. "A" or "B" appears in the display
To stop listening before the
indicating that the alarm has been activated.
The radio will turn on at the set time.
preset time
To set the buzzer alarm
Press OFF.
To change the sleep timer setting
1
Perform steps 1 to 8 in "To set the alarm. "
2
Press ALARM A or B to select "BUZZER" alarm
You can press SLEEP repeatedly to select the desired sleep timer
mode.
setting, even after the sleep timer has been activated.
The setting is entered. "A" or "B" appears in the display
To deactivate the sleep timer
indicating that the alarm has been activated.
The buzzer will sound at the set time.
Press SLEEP repeatedly to set the sleep timer to "OFF" in step 2.
Note
Note
The volume of the buzzer is not adjustable.
When the alarm time is set during the sleep timer duration,
To confirm an alarm time setting
the sleep timer will be deactivated automatically when the
alarm sounds.
Press ALARM TIME SET + or –. The setting will be displayed for
Connecting optional
about 4 seconds.
To change an alarm setting
components
Press and hold ALARM TIME SET + for at least 2 seconds to
To listen to sound
move the alarm time forwards. Press and hold ALARM TIME SET
– for at least 2 seconds to move the alarm time back.
You can enjoy sound from an optional component, such as a
When you release the button, the changed time will flash for
portable digital music player, through the speaker of this unit. Be
about 2 seconds. To change the alarm time again, press ALARM
sure to turn off the power of all components before making any
TIME SET + or – within these 2 seconds, otherwise the setting
connections.
change will be set as displayed.
1
Firmly connect the line output jack of a
Tips
portable digital music player (or other
"A" or "B" appears in the display indicating that the alarm time
component) to the AUDIO IN jack on the rear
has been changed and activated.
of the unit, using a suitable audio connecting
Even if the alarm has been set to off, the alarm will be
switched on when you change the alarm setting.
cable (not supplied).
2
Press AUDIO IN to activate the Audio-in
To doze for a few more minutes
function.
Press SNOOZE/BRIGHTNESS.
"AUDIO IN" appears in the display.
The sound turns off but will automatically come on again after
3
about 10 minutes.
Turn the connected component on.
You can change the snooze time by pressing SNOOZE/
4
Play the connected component.
BRIGHTNESS repeatedly within 4 seconds.
Sound from the connected component is output from the
The maximum length of the snooze time is 60 minutes.
speaker of this unit.
5
Adjust the volume using VOL + or –.
To stop the snooze timer, press OFF.
To return to the radio
To stop the alarm
Press FM/AM.
The preset number followed by the frequency of the last station
Press OFF to turn off the alarm.
appears in the display.
Press , FM/AM, or AUDIO IN to stop the alarm and activate
the corresponding function at the same time.
To return to the iPhone
The alarm will sound again at the same time the next day.
Press .
To deactivate the alarm
To stop listening
Press ALARM A or B to turn off the alarm A or B indicator in the
display.
Press OFF, and stop playback on the connected component.
To activate the alarm
Notes
The necessary type of audio connecting cable depends on the
Press ALARM A or B to turn on the alarm A or B indicator in the
optional component. Be sure to use the correct type of cable.
display.
If the volume level is low, adjust the volume of the unit first. If
the volume is still too low, adjust the volume of the connected
Notes
component.
When you are watching TV or listening to the radio with an
When alarm is set as iPhone, only the buzzer alarm will sound
optional component connected to the unit, the reception may
if there is no iPhone on the Dock connector, music is not
be poor.
stored in the iPhone, or the iPhone is turned off.
Disconnect the audio connecting cable from the unit when it
The alarm function works as usual on the first and last day of
is not in use.
daylight saving time (summer time). As a result, if the Auto
When you listen to the radio with an optional component
DST/summer time adjustment is set and the alarm is set at a
connected, turn off the connected component to prevent
time skipped when the daylight saving time begins, the alarm
noise. If noise occurs, even when the component is turned off,
will sound; if the alarm is set to a time that overlaps when
disconnect and place the optional component away from the
daylight saving time ends, the alarm will sound twice.
unit.
If the same alarm time is set for both alarm A and B, alarm A
takes priority.
If no operation is performed while the alarm is sounding, the
alarm will stop after about 60 minutes.
Other useful functions
General information
Setting the brightness of
Replacing the battery of
the display
the unit
Four levels of brightness are available by pressing SNOOZE/
1
Keep the AC adaptor connected to the wall
BRIGHTNESS.
outlet and unit, then remove the screw of the
battery compartment on the bottom of the
unit, then open the battery compartment lid.
Even if brightness level is set to Off, it will change to Low while
the alarm is sounding.
Press and hold SNOOZE/BRIGHTNESS to turn off the display
directly.
About App
A dedicated Dock App for iPod touch/iPhone available at Apple
App Store.
Search for "D-Sappli" and download the free App to find out
more about the functions.
2
Remove the old battery and insert a new one
Features
in the battery compartment with the side
D-Sappli includes various timer functions: Music Play Timer
and Sleep Timer.
facing up.
Music Play Timer allows you to play/pause desired music at a
desired time. Sleep Timer allows you to specify a time at which
to stop music playback.
Music Play Timer and Sleep Timer are available only when D-
Sappli is activated.
D-Sappli can display a list of Radio Preset Stations
programmed in this unit.
CR2032
You can rename the Radio Preset Stations, and change their
preset numbers on the D-Sappli. Preset numbers and order
will also be changed accordingly in the unit.
D-Sappli also includes a clock display enlarge feature.
You can synchronize time and date from the iPhone by simply
setting it on the Dock connector when D-Sappli is activated.
Notes
If the App to link with this unit is not downloaded to your iPod
3
Replace the battery compartment lid and
touch/iPhone, a pop-up message prompting you to download
D-Sappli may appear repeatedly.
tighten the screw.
Deactivate the App's link function to stop the pop-up
4
Press , FM/AM, AUDIO IN or SNOOZE/
message.
To deactivate the App's link function: Remove your iPod
BRIGHTNESS on the unit to turn "
touch/iPhone from the Dock connector. Press (to enter
the function for iPhone). Press and hold then OFF on the
display.
unit at the same time for at least 2 seconds. ("OFF" appears in
the display to show that the App's link function has been
Notes
deactivated.)
To re-activate the App's link function, repeat the above steps.
When you replace the battery, do not disconnect the plug
("On" appears in the display to show that the App's link
from the AC outlet. Otherwise, the current date, current time,
function has been activated.)
alarm and station presets will be erased.
If you are not going to use the remote for a long time, remove
the battery to avoid any damage that may be caused by
leakage or corrosion.
Troubleshooting
Should any problem persist after you have made the following
checks, consult your nearest Sony dealer.
General
The power does not turn on when the AC
adaptor is connected.
Make sure the AC adaptor is connected to the wall outlet
firmly.
There is no sound.
Make sure that the unit is connected to the AC power, and the
optional component is turned on.
Adjust the volume using VOL + or –.
Make sure that the optional component is correctly connected
to the unit.
The sound is low.
Adjust the volume using VOL + or –.
The sound is distorted.
Deactivate the equalizer function of the connected optional
component.
Lower the volume of the unit.
Sound skips or noise is heard.
Make sure that the optional component is correctly connected
to the unit.
Make sure that the optional component is not near a
television.
When the optional component is not in use with the unit,
disconnect the audio connecting cable from the AUDIO IN
jack.
The radio function of a connected optional
component does not work.
When an optional component equipped with radio or one
segment tuner is connected to the unit, its reception
sensitivity may be poor, resulting in no radio function.
Noise is heard.
Ensure that the unit is not near in-use portable phones, etc.
Disconnect the audio connecting cable from the AUDIO IN
jack when not in use.
The clock flashes "0:00" or "AM 12:00" due to
a power interruption.
The battery is low. Replace the battery. Remove the old
battery and install a new one.
The alarm of radio, iPhone or buzzer does
not sound at the preset alarm time.
Check that alarm "A" or alarm "B" is properly displayed.
The alarm of radio or iPhone is activated but
no sound comes on at the preset alarm time.
Check the alarm volume setting.
When daylight saving time (summer time)
begins, the clock does not employ the
daylight saving time (summer time)
automatically.
Make sure the clock is set correctly.
Press and hold OFF and DISPLAY/MEMORY on the unit
simultaneously for at least 2 seconds to activate the Auto DST/
summer time function.
When using an iPhone
There is no sound.
Make sure the iPhone is connected firmly.
Make sure that the connected iPhone is playing music.
Make sure that the function for iPhone is activated.
Check that the iPhone is compatible with this unit. (See
"Compatible iPod/iPhone models. " )
Operation is not performed.
Make sure the iPhone is connected firmly.
Check that the iPhone is compatible with this unit. (See
"Compatible iPod/iPhone models. " )
The iPhone does not charge.
Make sure the iPhone is connected firmly.
Make sure the AC adaptor is connected firmly.
Check that the iPhone is compatible with this unit. (See
"Compatible iPod/iPhone models. " )
Audio-in
There is no sound.
Make sure the audio connecting cable is connected firmly.
Make sure that the connected optional component is in
playback mode.
Increase the volume of the optional component without
causing sound distortion. To adjust the volume of the optional
component, refer to its user guide.
Make sure that the Audio-in function is activated.
The sound is low.
Check the volume of the connected optional component.
Increase the volume of the optional component without
causing sound distortion. To adjust the volume of the optional
component, refer to its user guide.
The sound is distorted.
Lower the volume of the optional component till the
distortion is not heard. To adjust the volume of the optional
component, refer to its user guide.
Remote control
The remote does not function.
" off in the
Replace the battery in the remote with a new one if it is weak.
Make sure that you are pointing the remote at the remote
sensor on the unit.
Do not cover or place any objects directly in front of the
remote sensor.
Remove any obstacles in the path between the remote and
the unit.
Make sure the remote sensor is not exposed to strong light,
such as direct sunlight or fluorescent lamp light.
If the problem persists, consult your nearest Sony dealer.
Specifications
Time display
Switching between 24-hour system (default) and 12-hour
system.
iPhone
DC out: 5 V
MAX: 1 A
Radio
Frequency range
Band
Frequency
Frequency step
FM
87.5 MHz - 108 MHz
0.05 MHz
AM
531 kHz - 1,602 kHz
9 kHz
General
Speaker
Approx. 40 mm dia.
Input
AUDIO IN jack (ø 3.5 mm stereo minijack)
Power output
Mono 0.8 W (at 10% harmonic distortion)
Power source
DC IN 6V (with supplied AC adaptor (AC 230 V, 50 Hz))
For clock back up: 3 V DC, CR2032 battery (1)
Dimensions
Approx. 126 mm × 92 mm × 100 mm (w/h/d)
including projecting parts and controls
Mass
Approx. 482 g
Supplied accessories
Remote control (with a lithium battery) (1)
AC adaptor (1)
AM loop aerial (1)
Startup Guide (1)
Reference Guide (this document) (1)
Compatible iPod/iPhone models
The compatible iPod/iPhone models are as follows.
Update the software of the iPod/iPhone to the latest version
before using it with this unit.
iPhone 5s
iPhone 5c
iPhone 5
iPod touch (5th generation)
iPod nano (7th generation) *
* The remote command of "MENU," "," "," and "ENTER" will
only work with iPhone and iPod touch.
Design and specifications are subject to change without notice.
Advertisement
