Related Manuals for Centrosolar TFP 288 Professional
Summary of Contents for Centrosolar TFP 288 Professional
- Page 1 Installation Guide TF Plate Professional Installation Guide TFP 288 Professional www.centrosolar.com...
-
Page 3: Table Of Contents
Installation Guide Contents About this guide Site preparation Installation prerequisites Safe Installation Commissioning of the System Maintenance and cleaning Technical Specifications Warranty and guarantee Disclaimer... -
Page 4: About This Guide
Installation Guide 1 About this guide 2 Site preparation Thank you for choosing Centrosolar TF Plate Professional. The TF Plate Professional modules are sensitive techni- If you have questions about the installation or components cal components, which must be handled with utmost care. -
Page 5: Installation Prerequisites
Installation Guide 3 Installation prerequisites Check the roof inclination: To facilitate sufficient drainage from the modules, the roof inclination must be at least 3°. The maximum authorized roof inclination for the TF Plate Professional installation is 60°. How to use the DC-Connect junction box: Fig. 2: Before placing the pallets on the roof check its load ca- The wiring of the modules with each other, with the cor- pacity! responding DC-Connect junction box, and/or with the in-... -
Page 6: Safe Installation
Installation Guide 4 Safe Installation the protection scheme against direct lightning strikes. Country-specific regulations must be observed. Distance between high beading and lining Due to the design of the TF Plate Professional it is not pos- The free distance between the high beadings of the trap- sible to provide the module with a fixed marked grounding ezoidal sheet metal and the lining of the TF Plate Profes- point in advance. - Page 7 Installation Guide Calibrating the TF Plate Professional Accurate sealing with butyl sealing strips. Determine the starting position for the laying of the first To guarantee optimum tightness, the butyl sealing strips module (zero point). Then determine the individual posi- must be cut to 50 mm x 50 mm and bonded to the trap- tions of the screws and butyl sealing strips.
- Page 8 Installation Guide Laying to butt at the edges All subsequent modules are laid to butt at the edges with distances predetermined on site. ~210 mm Fig. 13 Fig. 11 In case a screw connection is located directly on the edge of the trapezoidal metal sheet, fasten the mounting brack- et with the included MS polymer adhesive.
- Page 9 Installation Guide Wiring Information: TF Plate Professional Mounting the cable duct When wiring the TF Plate Professional module, please Apply an approx. 6 mm wide strip of MS polymer adhesive note that there are two electrically independent laminates with a 15 mm distance to the edge of the module carrier applied to the carrier sheet metal.
- Page 10 Installation Guide Sectional view of the TF Plate Professional: Top view: Mounting position cable duct on TF Plate Professional For a better understanding, we have numbered the indi- vidual areas in the overview. The corresponding remarks The example shows an installation with three TF Plate can be found below the figure. Professional modules.
-
Page 11: Commissioning Of The System
Installation Guide 5 Commissioning of the System 6 Maintenance and cleaning The commissioning of a photovoltaic system is part of the This photovoltaic system requires extremely little mainte- proper and professional implementation and installation. It nance and servicing. must only be performed following a careful visual examina- However, do inspect the system regularly and perform tion and a professional electrical inspection. -
Page 12: Technical Specifications
5 years Max. system voltage 1000 V ** According to stipulation of Centrosolar AG Warranty conditions (incl. product and performance warranty). The performance guarantees stated in this document are only valid if the installation has been registered at www.uni-solar.com. Design features... -
Page 13: Warranty And Guarantee
Photovoltaic systems consists of electrical and mechani- cal components, which are assembled to a complete sys- tem on site. CENTROSOLAR AG is not in a position to monitor the adherence to the information and instructions of this installation guide. Therefore CENTROSOLAR AG is... - Page 14 Installation Guide...
- Page 16 Tel.: +49 40 391065-0 Tel.: +1 480 3482555 Tel.: +31 344 767002 hamburg@centrosolar.com info.usa@centrosolar.com info.benelux@centrosolar.com CENTROSOLAR AG CENTROSOLAR FOTOVOLTAICO ESPAÑA S.L. CENTROSOLAR FRANCE SARL Otto-Stadler-Straße 23c Moll de Barcelona s/n Espace Européen 33100 Paderborn Edifici Nord, 7a planta 15, chemin du Saquin, Batiment G...
Need help?
Do you have a question about the TFP 288 Professional and is the answer not in the manual?
Questions and answers