Harman P43 Owner's Manual
Care and operation
Hide thumbs
Also See for P43:
- Owner's manual (44 pages) ,
- Owners manual care and operation (42 pages) ,
- Installation & operating manual (40 pages)
Table of Contents
Advertisement
INSTALLER: Leave this manual with party responsible for use and operation.
OwNER: Retain this manual for future reference.
Contact your local dealer with questions on installation, operation or service.
NOTICE: SAVE THESE INSTRUCTIONS
Model(s):
P43, P61A & P68
Freestanding Pellet Stove
P43
Use & Care Video
Use & Care Video
!
Tested and approved for wood pellets and shelled field
corn fuel only. Burning of any other type of fuel voids
your warranty.
!
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Contact local building or fire officials about restrictions
and installation inspection requirements in your area.
1
Owner's Manual
Care and Operation
P61A
P68
Use & Care Video
CAUTION
CAUTION
Harman® • P-Series Owner's Manual_R1 • 03/14
Please read this entire manual before
installation and use of this pellet fuel-
burning room heater.
Failure to follow these instructions could
result in property damage, bodily injury
or even death.
• Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
• Do not overfire - If any external part starts to glow, you
are overfiring. Reduce feed rate. Overfiring will void
your warranty.
• Comply with all minimum clearances to combustibles
as specified. Failure to comply may cause house fire.
wARNING
HOT SURFACES!
Glass and other surfaces are hot
during operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
stove.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
NOTE
To obtain a French translation of this manual, please
contact your dealer or visit www.harmanstoves.com
Pour obtenir une traduction française de ce manuel, s'il
vous plaît contacter votre revendeur ou visitez www.
harmanstoves.com
wARNING
3-90-436168c
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Harman P43
Summary of Contents for Harman P43
-
Page 1: Care And Operation
• Keep clothing, furniture, draperies and other flammable your warranty. materials away. CAUTION NOTE To obtain a French translation of this manual, please Check building codes prior to installation. contact your dealer or visit www.harmanstoves.com • Installation MUST comply with local, regional, state and national codes and regulations. Pour obtenir une traduction française de ce manuel, s’il • Contact local building or fire officials about restrictions vous plaît contacter votre revendeur ou visitez www. and installation inspection requirements in your area. harmanstoves.com Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 2: Welcome
être placé sous les parties horizontales du tuyau de raccord à la LOOR PROTECTOR DO NOT ReMOVe THIS LABeL / Ne PAS eNLeVeR CeTTe ÉTIQUeTTe cheminée et s’étendre à 51mm ø 2 po. au-delà de la mesure du tuyau. P.N. 3-90-04300 Rev F Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 3: Table Of Contents
P43 ......... -
Page 4: Limited Lifetime Warranty
All parts and material except as covered by Conditions, 1 Year Exclusions, and Limitations listed Igniters, electronic components, and glass 2 years Factory-installed blowers Molded refractory panels 3 years Firepots and burnpots 5 years 1 year Castings and baffles Manifold tubes, 7 years 3 years HHT chimney and termination 1 year Burners, logs and refractory years Limited 3 years Firebox and heat exchanger Lifetime All replacement parts 90 Days beyond warranty period See conditions, exclusions, and limitations on next page. 4021-645F 02-18-13 Page 1 of 2 Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 5: Warranty Conditions
HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Informa- tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider- ation must be given to appliance location and configuration, environmental conditions, insulation and air tightness of the structure. This warranty is void if: • The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling, cracking and discoloration of steel or enamel finishes. • The appliance is subjected to prolonged periods of dampness or condensation. • There is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited to, improper chimney or venting installation. LIMITATIONS OF LIABILITY: • The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE. 4021-645F 02-18-13 Page 2 of 2 Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 6: Product Specific And Important Safety Information
Heater (A) “Air to Fuel Ratio]. The P43 is EPA certified to comply with July 1990 particulate emission standards. B. Mobile Home Approved This appliance is approved for mobile home installations when not installed in a sleeping room and when an outside combustion air inlet is provided. The structural integrity of the mobile home floor, ceiling, and walls must be maintained. The appliance must be properly grounded to the frame of the mobile home and use only listed pellet vent, Class “PL” connector pipe. A Harman® Outside Air Kit must be installed in a mobile home installation. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 7: Btu & Efficiency Specifications
E. BTU & Efficiency Specifications *BTU output will vary, depending on the brand of fuel you use in your appliance. Consult your Harman® dealer for P43 Freestanding Pellet Stove: best results. Particulate WARNING! Risk of Fire! Hearth & Home Technologies Average Emissions - 1.4 g/h Emissions Rating: disclaims any responsibility for, and the warranty and agency... -
Page 8: General Information
• Never leave children alone near a hot stove, whether operating or cooling down. • Teach children to NEVER touch the stove. • Consider not using the stove when children will be present. • Use only specified components as replacement parts. Other components may not allow your stove to operate as it was intended. Contact your dealer for more information, or visit: www. hpba.org/safety-information. To prevent unintended operation when not using your stove for an extended period of time (summer months, vacations, trips, etc): • Unplug stove from receptacle. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 9: Control Explanation
Mode, or OFF. Also allows you to constant burn setting, while in Constant burn Mode, Dealers exclusively. vary the distribution blower speed using the inner scale marked from 1 to 7. by turning the knob to the high or low side of each mode. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 10: Fuel Specification
Minerals and other non-combustible materials, like sand, will turn into a hard glass-like substance when heated. Trees from different areas will vary in mineral content. For NOTICE this reason, some fuels will produce more clinkers than others. Hearth & Home Technologies is not responsible for stove performance or extra maintenance required as a result of Moisture using fuel with higher ash or mineral content. Always burn dry fuel. Burning fuel with high moisture content takes energy to dry and tends to cool the appliance thus, robbing heat from your home. Damp pellet fuel could turn back into sawdust which does not flow properly through the feed system. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 11: General Operating Information
AS GASOLINE, NAPHTHA OR ENGINE OIL. settings, it will run quieter but take longer to heat up an area • DO NOT USE CHEMICALS OF FLUIDS TO START THE than if it were set at a higher burn rate. FIRE. Regardless of the burn rate, when the area is warm enough • Combustible materials may ignite. to satisfy the room sensor, the appliance will shut off. E. Before Your First Fire 1. Make sure your appliance has been properly installed and that all safety requirements have been met. Pay particular attention to the fire protection and venting instructions. 2. Double check that the ash pan and firebox are empty! 3. Close the front door. Figure 3.1 Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 12: Operating Instructions
Figure 4.3. This insures that plenty of allow 15 minutes for feed adjustment to take effect. fuel enters the burn pot for proper ignition. 4. Flip toggle switch to desired mode “auto or manual”. Figure CAUTION 4.4. Set feed limit knob to desired setting and turn mode dial to “Room Temp” or “Constant burn” Figure 4.5. Note: Odors and vapors released during initial operation. Feed rate of #4 is a good starting point. Adjustments may • Curing of high temperature paint. need to be made depending on fuel quality and/or heat • Open windows for air circulation. output desired. Odors may be irritating to sensitive individuals. 5. The fuel feed system and the igniter should now be on. 6. Once the appliance has ignited, let it burn for approximately 7-10 minutes. After this time, the igniter light should turn off and the unit should begin to operate per the settings at the control. Figure 4.2 Figure 4.3 Figure 4.4 Figure 4.5 Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 13: Ignition Cycles
• Within space required for loading or ash in accordance to what temperature the room sensor is removal. reading. When the room sensor is satisfied the blower will shut down until the room sensor sees a demand for heat. 3. Occasionally the appliance may run out of fuel and shut itself down. When this happens, the unit will need to be turned to the off position and restarted. If needed, follow the instructions in Section A “Starting Your First Fire”. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 14: Automatic Ignition
1" or less ash bed is not obtainable, it is not a problem. The 1" ash bed is only at maximum burn rate and during normal operation, the ash bed will be larger. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... - Page 15 To kill the fire or stop burning the stove, turn the Mode Selector to “OFF”. This will cause the fire to diminish and burn out. When the fire burns out and the stove cools down everything will stop. If you pull the plug to shut down the stove, all motors will stop. This may cause incomplete combustion and smoke in the firebox. If the load door is opened, the smoke may escape. The best way to shut down the stove is simply let it run out of pellets, then the stove will shut down automatically. This setting will produce continuous maximum heat output with the distribution blower at full speed. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
-
Page 16: Manual Ignition
IN THIS HEATER. KEEP ALL SUCH LIQUIDS wELL a problem. The 1" ash bed is only at maximum burn rate and AwAY FROM THE HEATER, wHILE IN USE. during normal operation, the ash bed will be larger. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... - Page 17 NOTE: During the use of this mode, if you keep increasing the temperature dial setting to increase the fire size, the distribution blower will automatically come on when the ESP Temperature reaches 350 F, or 81% output. ° Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
-
Page 18: Proper Shutdown Procedure
Exhaust Path More frequently depending on ash build-up Firebox - Prepare for Non-Burn Season At end of heating season Burnpot - Burning pellets - hardwood Every 3 bags Burnpot - Burning pellets - softwood Every 5 bags Glass When clear view of burnpot becomes obscure Hopper / Hopper Lid Gasket Every 50 bags of fuel or when changing fuel types Venting System More frequently depending on the fuel type NOTICE: These are recommendations. Clean more frequently if you encounter heavy build-up of ash at the recommended interval or you see soot coming from the vent. Not properly cleaning your appliance on a regular basis will void your warranty. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 19: Glass Maintenance
Carefully remove damaged glass, gasket material, and hold down clips (set aside). Install the self adhesive 1/4”” gasket material around the front face of the glass. Set the glass panel and gasket gently onto the door. Install the hold down clips and tighten with bolts. Glass - Cleaning Sometimes it will be necessary to clean accumulated ash from the glass surface; allowing this ash to remain on the glass for long periods can result in “etching” due to the acidity of the ash. Never clean the glass while it is hot, and do not use abrasive substances. Wash the surface with cool water, and rinse thoroughly. You may wish to use a non-abrasive cleaner specifically designed for use on stove glass. In any case, dry thoroughly before relighting your stove. P43 & P61A Freestanding Pellet Stove Replace glass only with high temperature mirrored ceramic glass. Inspect door gasket during cleaning and inspection Glass Gasket P68 Freestanding Pellet Stove... -
Page 20: Burnpot Maintenance
Note: The hot lead/cold lead connection must always be pulled to the rear of the feeder body before operation. Igniter hot lead wires (High temperature) Figure 5.3 Viewed from below through the ash pan opening. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 21: Combustion Blower Chamber
The exhaust passage may need cleaned as well. Keep in mind the ESP Sensor is located just inside the exhaust Intake Retainer passage Figure 5.7. Be sure not to damage the ESP Sensor Combustion Intake Cover Figure 5.4 while cleaning this area. Exhaust Passage ESP Sensor Pull up on Intake Retainer Figure 5.5 Figure 5.7 Pull and slide to the right Figure 5.6 Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 22: Pellet Feeder Chamber
5.9. • Reinstall the cover making certain it is seated properly on the feeder body and tighten as tightly as you can by hand. NOTE: views are shown with the rear motor covers removed. Feeder clean out cover 5/16" wing Nut Figure 5.9 Pellet Metering Possible pellet fines Slide Plate buildup area. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 23: Troubleshooting And Frequently Asked Questions
4 Blinks: Can occur only in Room Temp Mode and on to the desired mode. If the unit was not out of pellets, see indicates Room Sensing Probe failed or not installed. If a Troubleshooting section for more details. Room Sensing Probe is then installed, the status light will automatically reset. * Manual reset- disconnect power cord for a few seconds and reconnect. If error still occurs call your Dealer. NOTE: Unit will not start in "AUTO" with this status error. 5 Blinks (In Igniter Auto. Mode Only): Indicates that the unit has failed to light within the 36 minute start cycle. To reset - Turn Mode Selector to "OFF", then turn to either mode again.) Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 24: Frequently Asked Questions
7. Large flame at start-up. 7. This is normal. Flame will settle down once the fire is established. Contact your dealer for additional information regarding operation and troubleshooting. visit www.harmanstoves. com to find dealer. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 25: Troubleshooting
Fuel should not be stored within the stove installation FIRE HAS GONE OUT- Check for status light. clearances or within the space required for cleaning and 1. No fuel in hopper. ash removal. 2. Draft is too low, blocked flue. 3. Something is restricting fuel flow. 4. Hopper lid not closed properly. 5. Feed motor or combustion blower has failed. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 26: Reference Materials
Reference Material A. Safety Reminders When operating your Harman® P-Series Pellet Stove, WARNING respect basic safety standards. Read these instructions carefully before you attempt to operate the P-Series Pellet Stove. Failure to do so may result in damage to property or MOBILE/MANUFACTURED HOME GUIDELINES DO personal injury and may void the product warranty. NOT ALLOw INSTALLATION IN A SLEEPING ROOM. CAUTION: This appliance must be vented to the outside. -
Page 27: Motor And Component Location
(Draft) in the firebox. If the high limit and one backup high limit. The control has an automatic draft becomes too low for proper combustion, the switch opens, diagnostic circuit that continuously monitors the ESP and Room cutting power to the feed motor and the igniter circuits. This switch Sensor for faults. If a fault should occur, the control sends a status is connected into the AC (high voltage) wiring. alert and at the same time the unit goes down to minimum feed/ minimum burn as a safety condition. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... -
Page 28: Loss Of Power Addendum
Contact your dealer if you have questions about UPS compatibility with your appliance. Harman® Surefire 512H Battery Back-up The 512H connects to a 12 volt deep cycle battery that will run your appliance for up to eight (8) hours. It includes a trickle charge feature that keeps your battery charged when power is available. -
Page 29: Service Parts
Hearth and Home Technologies does not sell directly to consumers. Provide model number Stocked and serial number when requesting service parts from your dealer or distributor. at Depot ITEM Description COMMENTS PART NUMBER 1-10-09537A Pre 008084166 1-00-232108 Hopper Assembly Post 008084166 1-10-09537A Hopper Knob Post 008168147 1-00-02000-1 Hopper Lid w/Hinge, Swell Latch Pre 008168147 1-10-08518 Hopper Lid w/Hinge, Knob Post 008168147 1-10-773900 Hopper Switch 48” Post 008084166 3-20-232108 Hopper Extension Switch Kit 1-00-06826 Additional service parts on following page. 2/14 Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... - Page 30 2-00-677138-10 Gasket, UL Feeder 1-00-677122 2.11 2.12 Slide Plate Assembly 1-10-677121A UL Feeder Auger Assembly 3-50-00565 2.13 2.14 Bearing Flange w/Hardware 1-00-04035 2.15 UL Feeder Gear Motor Bracket w/Grommet 1-00-247406 2.16 UL Feeder Cam Block 3-00-677154 Hopper Switch Feeder Fitting Pkg of 2 1-00-142818 Motor Bracket Grommet Pkg of 12 3-31-2761-12 Pillow Block Pkg of 4 3-31-3614087-4 Silicone Tubing, 1/8” 5 Ft 1-00-5113574 Additional service parts on following page. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
- Page 31 Pkg of 10 3-31-782108-10 Fire Brick 4-1/2 x 9 x 1-1/4” Pkg of 7 1-00-900450125 Firebrick, Full Skid 414 Pcs 3-40-900450-414 Hopper Heat Shield 2-00-773854B Feeder Cover 2-00-773826L Circuit Board w/Knobs & Shafts 1-00-05886 Control Board Label 3-90-07766 Circuit Board Plate, Studded w/label 1-10-08327 Knob, Contol Board/D-Shaft 25 Sets 1-00-015605 Airwash O-Rings Pkg of 10 1-00-939639 Arrow Burn Pot Scraper Pkg of 10 2-00-773850-10 Cradle Assembly Igniter Holder, Cradle, & Flat Bottom 3 Sets 1-00-06620 Additional service parts on following page. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
- Page 32 Touch up Paint, Black Post 008164569 3-42-19905 Wiring Harness 3-20-08727 Gold 3-43-06802-4 LeafDoor Trim Brushed Stainless 3-43-06802-7 Bright Nickel 3-43-06802-8 Modern Door trim Brushed Stainless 3-43-06839-7 Gold 3-43-08400 Ash Lip Trim Brushed Stainless 3-43-08400-7 Bright Nickel 3-43-08400-8 Gold 3-43-06729-4 Tile Frame Brushed Stainless 3-43-06729-7 Bright Nickel 3-43-06729-8 Spring Clips (Required for installation of Tile Frame) Pkg of 20 3-31-232547-20 Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
-
Page 33: P61A
Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor. at Depot ITEM Description COMMENTS PART NUMBER Pre 008085092 1-10-08622 Hopper Assembly Post 008085092 1-10-09546A Hopper Extension Switch Kit 1-00-06826 Hopper Knob Post 008093438 1-00-02000-1 Hopper Switch 48” Post 008087704 3-20-232108 Additional service parts on following page. 3/14 Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... - Page 34 3-50-00465 Cam Bearing 3-31-3014 Bearing Flange w/Hardware 1-00-04035 2.10 Bracket, Gear Motor Pkg of 2 1-00-01534 2.11 Gear Motor, 4 RPM 3-20-60906 Gear Motor Fan Blade Pkg of 3 3-20-2046399-3 2.12 Cast Cam Block 3-00-00153 Feeder Air Crossover Kit 1-00-67900 Feeder Repair kIt 1-00-677150 Gasket, Feeder, Air Intake Pkg of 6 3-44-72224-6 Motor Bracket Grommet Pkg of 12 3-31-2761-12 Pillow Block Pkg of 4 3-31-3614087-4 Additional service parts on following page. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
- Page 35 1-00-677122 Slide Plate Assembly 1-10-677121A 3.12 3.13 UL Feeder Auger Assembly 3-50-00565 3.14 Pellet Feeder Bearing Retainer w/Hardware Pkg of 2 1-00-04035 UL Feeder Gear Motor Bracket w/Grommet 1-00-247406 3.15 3.16 UL Feeder Cam Block 3-00-677154 Gasket, Hopper Throat 3-44-677185 Hopper Switch Feeder Fitting Pkg of 2 1-00-142818 Motor Bracket Grommet Pkg of 12 3-31-2761-12 Pillow Block Pkg of 4 3-31-3614087-4 Silicone Tubing, 1/8” 5 Ft 1-00-5113574 Additional service parts on following page. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
- Page 36 2 Sets 1-00-00247 Burn Pot Weldment 1-10-05802 Flame Guide 3-00-08534 Clean Out Cover 2 Sets 1-00-06623 Thumb Screw Pkg of 10 3-31-782108-10 Fire Brick 4-1/2 x 9 x 1-1/4" Pkg of 7 1-00-900450125 Fire Brick , Full Skid 414 Pcs 3-40-900450-414 Hopper Heat Shield 2-00-06471B Feeder Cover 2-00-773826L Circuit Board w/Knobs & Shafts 1-00-05886 Circuit Board Plate, Studded w/label 1-10-08327 Control Panel Label 3-90-07766 Knob, Contol Board/D-Shaft 25 Sets 1-00-015605 Additional service parts on following page. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
- Page 37 Touch up Paint, Black, 12 oz Can Post 008092412 3-42-19905 Wiring Harness 3-20-08727 Gold 3-43-06802-4 Leaf Door Trim Brushed Stainless 3-43-06802-7 Bright Nickel 3-43-06802-8 Modern Door Trim Brushed Stainless 3-43-06839-7 Gold 3-43-08400 Ash Lip Trim Brushed Stainless 3-43-08400-7 Bright Nickel 3-43-08400-8 Gold 3-43-06729-4 Tile Frame Brushed Stainless 3-43-06729-7 Bright Nickel 3-43-06729-8 Spring Clips (Required for installation of Tile Frame) Pkg of 20 3-31-232547-20 Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
-
Page 38: P68
Hearth and Home Technologies does not sell directly to consumers. Provide model number and serial number when requesting service parts from your dealer or distributor. at Depot ITEM Description COMMENTS PART NUMBER Pre 008280309 1-10-06709 Hopper Assembly Post 008280309 1-10-09547A Hopper Extention Switch Kit 1-00-06826 Hopper Knob Post 008295042 1-00-02000-1 Hopper Switch Post 008284286 3-20-232108 Additional service parts on following page. 3/14 Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c... - Page 39 3-50-00465 Cam Bearing 3-31-3014 Bearing Flange w/Hardware 1-00-04035 2.10 Bracket, Gear Motor Pkg of 2 1-00-01534 2.11 Gear Motor, 4 RPM 3-20-60906 Pkg of 3 3-20-2046399-3 Fan Blade, Feed Motor 2.12 Cast Cam Block 3-00-00153 Feeder Air Crossover Kit 1-00-67900 Feeder Repair Kit 1-00-677150 Gasket, Feeder, Air Intake Pkg of 6 3-44-72224-6 Motor Bracket Grommet Pkg of 12 3-31-2761-12 Pillow Block Pkg of 4 3-31-3614087-4 Additional service parts on following page. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
- Page 40 1-00-677122 3.11 3.12 Slide Plate Assembly 1-10-677121A UL Feeder Auger Assembly 3-50-00565 3.13 Bearing Flange w/Hardware 1-00-04035 3.14 UL Feeder Gear Motor Bracket w/Grommet 1-00-247406 3.15 UL Feeder Cam Block 3-00-677154 3.16 Gasket, Hopper Throat 3-44-677185 Hopper Switch Feeder Fitting Pkg of 2 1-00-142818 Motor Bracket Grommet Pkg of 12 3-31-2761-12 Pillow Block Pkg of 4 3-31-3614087-4 Silicone Tubing, 1/8" 5 Ft 1-00-5113574 Additional service parts on following page. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
- Page 41 Contains: Handle, 6 mm Washer, SHCS, handle, Dowel, Plunger, SSS, Bhcs Ball Plunger Pkg of 3 3-31-5500-3 Front Door Latch 3-00-249119P Latch Ball Spring Bracket 2-00-06714 Wooden Handle , Load Door Pkg of 2 1-00-00247 Burn Pot Weldment 1-10-06723 Flame Guide 3-00-03000 Clean Out Cover 2 Sets 1-00-06623 Thumb Screw Pkg of 10 3-31-782108-10 Fire Brick 4-1/2 x 9 x 1-1/4” Pkg of 7 1-00-900450125 Fire Brick , Full Skid 414 Pcs 3-40-900450-414 Hopper Heat Shield 2-00-06715B Feeder Opening Cover 2-00-773826L Additional service parts on following page. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
- Page 42 1-00-199110 Rubber Spacer Pkg of 10 3-31-901311-10 Load Door Hinge 2-00-06707L Hopper Muffl er and Fittings 1 set 1-00-18186618 Outside Air Termination Cap 1-10-09542 Room Sensor 3-20-00906 Power Cord 3-20-39685 Pre 008281295 3-20-11744 Thermister Probe (ESP Probe) Post 008281295 3-20-00844 Thermostat Extension 3-20-00607 Pre 008293174 3-42-1990 Touch up Paint, Black, 12 oz Can Post 008293174 3-42-19905 Wiring Harness 3-20-08727 Additional service parts on following page. Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
- Page 43 ITEM Description COMMENTS PART NUMBER Gold 3-43-06717-4 Leaf Door Trim Brushed Stainless 3-43-06717-7 Bright Nickel 3-43-06717-8 Modern Door Trim Brushed Stainless 3-43-06797-7 Gold 3-43-08400 Ash Lip Trim Brushed Stainless 3-43-08400-7 Bright Nickel 3-43-08400-8 Gold 3-43-06729-4 Tile Frame Brushed Stainless 3-43-06729-7 Bright Nickel 3-43-06729-8 Pkg of 20 3-31-232547-20 Spring Clips (Required for the installation of Tile Frame) Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
-
Page 44: Contact Information
DO NOT DISCARD THIS MANUAL • Read, understand and follow • Important operating • Leave this manual with a n d m a i n t e n a n c e these instructions for safe party responsible for use instructions included. installation and operation. and operation. Printed in U.S.A. - Copyright 2012 Harman® • P-Series Owner’s Manual_R1 • 03/14 3-90-436168c...
Need help?
Do you have a question about the P43 and is the answer not in the manual?
Questions and answers