How To Set The Spa Side Switch Buttons; How To Set The Spalink Rs Buttons - Jandy AquaLink RS Owner's Manual
All button control panel
Hide thumbs
Also See for AquaLink RS:
- Owner's manual (68 pages) ,
- Installation manual (40 pages) ,
- Troubleshooting manual (28 pages)
Table of Contents
Advertisement
The SPA SIDE SWITCH Menu allows you to define which equipment
is controlled by the buttons (4 buttons per Spa Side Switch) on the
optional Spa Side Switch(es).
You may want to write down your spa side switch button assignments
so that you can label the buttons on the switch with the label pack
provided.
The SPA LINK Menu allows you to define which equipment is
controlled by the buttons (8 buttons per SpaLink RS) on the optional
SpaLink(s).
You may want to write down your SpaLink RS button assignments so
that you can label the buttons on the switch with the label pack
provided.
1.
Press the MENU button, then press the FORWARD button
and scroll through until you reach SYSTEM SETUP. Hit
ENTER then FORWARD to SPA SWITCH. Hit ENTER again.
The display will read 1 SWITCH <—>*. Use the FORWARD
and BACK arrows to move between 1 SWITCH, 2 SWITCHES
and 3 SWITCHES. Depending on how many Spa Side
Switches you have, choose an option and press ENTER.
2.
The AquaLink RS display will read SELECT DEVICE FOR
BUTTON 1. Press the button on the Controller for the piece
of equipment that you want to control from the first button of
the Spa Side Switch (e.g., press the Spa button).
3.
Repeat this process for each remaining button on the Spa
Side Switch. When you are finished, the AquaLink RS display
will show the settings for each button.
NOTE: If there is more than one Spa Side Switch on the
system, the buttons on the second switch will be buttons
5-8, and the buttons on the third Spa Side Switch will be
buttons 9-12.
1.
Press the MENU button, then press the FORWARD button
and scroll through until you reach SYSTEM SETUP. Hit
ENTER then FORWARD to SPA LINK. Hit ENTER again.
The display will read 1 SPA LINK <—>*. Use the FORWARD
and BACK arrows to move between 1 SPA LINKS, 2 SPA
LINKS and 3 SPA LINKS. Depending on how many SpaLinks
you have, choose an option and press ENTER.
2.
The AquaLink RS display will read SELECT DEVICE FOR
BUTTON 1. Press the button on the Controller for the piece
of equipment that you want to control from the first button of
the SpaLink RS (e.g., press the Spa button).
3.
Repeat this process for each remaining button on the
SpaLink RS. When you are finished, the AquaLink RS display
will show the settings for each button.
NOTE: If there is more than one SpaLink RS on the system,
the buttons on the second switch will be buttons
5-8, and the buttons on the third SpaLink will be buttons 9-12.
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the AquaLink RS and is the answer not in the manual?
Questions and answers
I have an RS8 controller, I can’t seem to operate the spa heat independent of the pool, the spillover feature doesn’t turn off, so the pool and spa filter and heat together ( just moved into the home with this pool have a RS6 at previous home)
To operate the spa heat independently from the pool using the Jandy AquaLink RS8 controller, follow these steps:
1. Ensure Proper Valve Actuation – The Intake and Return Jandy Valve Actuators (JVAs) must be synchronized to switch water circulation properly between the pool and spa when Spa Mode is activated.
2. Use One-Touch Macro Settings – Configure custom one-touch settings in the web interface to control the Solar and Gas heating functions separately.
3. Activate Spa Mode – Press the Spa button on the AquaLink RS controller to switch circulation to the spa.
4. Turn On the Spa Heater – Once in Spa Mode, enable the spa heater through the interface. This should start heating the spa independently.
5. Check Heater Activation – If both heaters turn on in Spa Mode, verify system wiring and settings, as some setups may automatically activate both heaters.
6. Adjust Scheduling – If needed, assign heating functions to a schedule for automatic activation.
If the spa heater does not operate independently or the pool heater turns on when not desired, further configuration or system adjustments may be required.
This answer is automatically generated
Reset the clock and now the pool doesn’t come on and off automatically also does the lockout need to be on or off
To reset the Jandy AquaLink RS for automatic pool operation, follow these steps:
1. Ensure the system is powered on.
2. Check if the lockout feature is enabled. If it is, disable it, as it may prevent manual or automatic operation.
3. Verify that the control panel buttons are responsive.
4. If the system is not functioning correctly, try cycling the power by turning it off and then back on.
5. Ensure that the pool mode settings are correctly configured for automatic operation.
The lockout feature should be off to allow normal automatic operation.
This answer is automatically generated
What does the AUX6 button control
The AUX6 button on the Jandy AquaLink RS controls the auxiliary function assigned to it in the system setup. It only works when the panel is in service mode and must be assigned in the “Label Auxiliaries” screen.
This answer is automatically generated