Jandy AquaLink RS Owner's Manual
All button control panel
Hide thumbs
Also See for AquaLink RS:
- Owner's manual (68 pages) ,
- Installation manual (40 pages) ,
- Troubleshooting manual (28 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Jandy AquaLink RS
Summary of Contents for Jandy AquaLink RS
- Page 1 ® All Button Control Panel...
- Page 2 Safety Precautions Filter Pump Button Spa Button AUX Buttons Heater Buttons Display Hold/Release Button Program Review Set Temperature Set Time Lockouts Program Groups Display Light Label Aux Spa Side Switch SpaLink RS Freeze Protection Air Temperature Degrees F/C Temperature Calibration Assign JVA Set Dimmers Diagnostics...
- Page 3 Read and follow all instructions. Lire la notice technique. DANGER- To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times. WARNING- Water temperature in excess of 100°F/38°C may be injurious to your health. AVERITSSEMENT: Des Températures de l'eau supérieures à...
- Page 4 Display Rotates between messages indicating time/date/ temperature and status of equipment. Display Hold/ Filter Pump Release Button Stops or starts the Turns on the filter display rotating pump and starts through messages water circulation. (i.e., time, date, temperature). Auxiliary Spa Button Buttons Turns on the filter Turns on and off...
- Page 5 Press the DISPLAY HOLD/RELEASE button once to The DISPLAY HOLD/RELEASE button locks the AquaLink RS lock the AquaLink RS display on the desired message display that cycles through displays of time, date, temperature and or readout. Press it again to release it, allowing the equipment status (i.e., PUMP OFF).
- Page 6 The MENU button on the AquaLink RS allows you to control and customize the features of the unit. Below is a brief list of things you can do with the menu button: Program equipment (set times for equipment to automatically go on and off)
- Page 7 If you have more than one program (i.e., more than one on and off time) for a piece of equipment, when you enter a second program, the AquaLink RS display will read 1 PROGRAM TIME ALREADY EXISTS. If more than one program time already exists, the AquaLink RS will display how many program times exist.
- Page 8 Press the MENU button. Use the FORWARD and BACK buttons The SET TIME Menu lets you set the AquaLink RS’s internal clock. to move to the SET TIME Menu and press ENTER. The It is important to set the correct time and date so that AquaLink RS display will read YEAR 1998 <—>* .
- Page 9 Program groups are useful for setting specific programs for summer Press the MENU button. Use the FORWARD and BACK buttons to and winter use, or for vacation and at-home. The AquaLink RS will move to the PGM GROUP Menu and press ENTER. The AquaLink store separate programs for each group.
- Page 10 Spa Side Switch (e.g., press the Spa button). Repeat this process for each remaining button on the Spa Side Switch. When you are finished, the AquaLink RS display will show the settings for each button. NOTE: If there is more than one Spa Side Switch on the...
- Page 11 Default freeze protection activation temperature is 38º F. Normal items to assign to freeze protection are spa jet pump or waterfall If you are assigning items , the AquaLink RS display will read pump. ENTER DEVICE TO ADD TO FREEZE PROTECTION. Press ENTER when done.
- Page 12 Use the FORWARD and BACK buttons to bump the temperature display up or down. NOTE: This will not change the temperature of the water, only the display of the temperature on the AquaLink RS Display. Press ENTER when the desired temperature is displayed.
- Page 13 (usually gas heater) will take over to bring the water up to the thermostat setting. When the AquaLink RS is setup to control this feature, the "Solar Under SYSTEM SETUP, use the forward or back arrow to move to IN JVA"...
- Page 14 3. If there is only one program , press ENTER. The program will be canceled. 4. If there are more than one programs, the AquaLink RS display will tell you how many programs there are (for example, if there are three programs, the AquaLink RS display will read 3 PROGRAMS EXIST).
- Page 15 The optional Spa Side Switch is a four button remote unit that duplicates the functions of four buttons of your choice from the indoor AquaLink RS Controller. To set which functions the Spa Side Switch will control, please see page 9. To use the Switch, simply press the buttons.
- Page 16 Spillover Rev. "I" - Rev. "I" of the AquaLink RS software corrects the operation of the return valve on Aux. 3 from the power center override switches. When Dip Switch 3 is in the ON position, the Aux. 3 relay socket is activated and the return valve actuator turns. The spillover is disabled while the spa is on, message is displayed when the spa spillover is in spa mode (water circulation is to spa).
- Page 17 5 minutes. PUMP WILL TURN ON AFTER DELAY - This message is displayed during pool/spa switching. The AquaLink RS waits 35 seconds while the valves turn from pool position to spa position (or vice-versa) before activating the filter pump.
- Page 19 CANCEL SOME Select device to PROGRAMS be canceled CANCEL ALL Press enter to remove all devices except pump from FRZ PROTECT freeze protection, or cancel to abort Select AUX to AUX LABEL Label removed remove label from CANCEL BUTTON Press enter to Select AUX to cancel dimmers, DIMMERS*...
- Page 21 Listed 4J3 Swimming Pool & Spa Controller 6000 Condor Drive, Moorpark, CA, USA 93021 • 707.776.8200 FAX 707.763.7785 480 S. Service Road West, Oakville, Ontario, Canada L6K 2H4 • 905.844.8233 FAX 905.844.2635 Litho in U.S.A. © Water Pik Technologies, Inc. 2001 Sheet #6593 Rev.
Need help?
Do you have a question about the AquaLink RS and is the answer not in the manual?
Questions and answers
I have an RS8 controller, I can’t seem to operate the spa heat independent of the pool, the spillover feature doesn’t turn off, so the pool and spa filter and heat together ( just moved into the home with this pool have a RS6 at previous home)
To operate the spa heat independently from the pool using the Jandy AquaLink RS8 controller, follow these steps:
1. Ensure Proper Valve Actuation – The Intake and Return Jandy Valve Actuators (JVAs) must be synchronized to switch water circulation properly between the pool and spa when Spa Mode is activated.
2. Use One-Touch Macro Settings – Configure custom one-touch settings in the web interface to control the Solar and Gas heating functions separately.
3. Activate Spa Mode – Press the Spa button on the AquaLink RS controller to switch circulation to the spa.
4. Turn On the Spa Heater – Once in Spa Mode, enable the spa heater through the interface. This should start heating the spa independently.
5. Check Heater Activation – If both heaters turn on in Spa Mode, verify system wiring and settings, as some setups may automatically activate both heaters.
6. Adjust Scheduling – If needed, assign heating functions to a schedule for automatic activation.
If the spa heater does not operate independently or the pool heater turns on when not desired, further configuration or system adjustments may be required.
This answer is automatically generated
Reset the clock and now the pool doesn’t come on and off automatically also does the lockout need to be on or off
To reset the Jandy AquaLink RS for automatic pool operation, follow these steps:
1. Ensure the system is powered on.
2. Check if the lockout feature is enabled. If it is, disable it, as it may prevent manual or automatic operation.
3. Verify that the control panel buttons are responsive.
4. If the system is not functioning correctly, try cycling the power by turning it off and then back on.
5. Ensure that the pool mode settings are correctly configured for automatic operation.
The lockout feature should be off to allow normal automatic operation.
This answer is automatically generated
What does the AUX6 button control
The AUX6 button on the Jandy AquaLink RS controls the auxiliary function assigned to it in the system setup. It only works when the panel is in service mode and must be assigned in the “Label Auxiliaries” screen.
This answer is automatically generated