Panasonic KT2 Instruction Manual page 21

Input type (Character indication) and range
: K -200 to 1370
: -199.9 to 400.0
: J -200 to 1000
: R 0 to 1760
: S 0 to 1760
: B 0 to 1820
: E -200 to 800
: T -199.9 to 400.0
: N -200 to 1300
: PL- 0 to 1390
: C(W/Re5-26) 0 to 2315
: Pt100 -199.9 to 850.0
: JPt100 -199.9 to 500.0
: Pt100 -200 to 850
: JPt100 -200 to 500
:
4 to 20mA DC -1999 to 9999
: 0 to 20mA DC -1999 to 9999
Press key for 3sec while holding down the
[Auxiliary function setting mode 2]
Input type • Make a selection with the
, Selection • Default value:
PV/SV
Scaling high limit • Set the value with the
, Set value • Default value: 1370
PV/SV
Scaling low limit • Set the value with the
• Default value: -200
, Set value
PV/SV
Decimal point place • Make a selection with the
• Available only for DC input
, Selection
PV/SV
PV filter time constant
• Set the value with the
, Set value
PV/SV
• Set the value with the
OUT1 (Heating) high limit
• Not available if OUT1 is ON/OFF action
, Set value
PV/SV
OUT1 (Heating) low limit • Set the value with the
• Not available if OUT1 is ON/OFF action
, Set value
PV/SV
OUT1 (Heating)
• Set the value with the
ON/OFF action hysteresis
• Available only when OUT1 is ON/OFF action
, Set value
PV/SV
EV1 output • Make a selection with the
• Not available if Heat/Cool control option is added
, Selection
PV/SV
EV2 output • Make a selection with the
•
, Selection Not available if Serial communication option is added
PV/SV
Overlap/Dead band • Set the value with the
, Set value • Available only when Heat/Cool control option is added
PV/SV
OUT2 (Cooling ) • Set the value with the
• Available when
ON/OFF action hysteresis
,Set value and when OUT2 is ON/OFF action
PV/SV
(1)
A1 type • Make a selection with the
, Selection • Default value:
PV/SV
A2 type • Make a selection with the
, Selection • Default value:
PV/SV
(2)
• Set the value with the
A1 hysteresis
• Not available if
, Set value
is selected during A1 type selection
PV/SV
• Set the value with the
A2 hysteresis
• Not available if
, Set value
is selected during A2 type selection
PV/SV
: K -320 to 2500
: -199.9 to 750.0
: J -320 to 1800
: R 0 to 3200
: S 0 to 3200
: B 0 to 3300
: E -320 to 1500
: T -199.9 to 750.0
: N -320 to 2300
: PL- 0 to 2500
: C(W/Re5-26) 0 to 4200
: Pt100 -199.9 to 999.9
: JPt100 -199.9 to 900.0
: Pt100 -300 to 1500
: JPt100 -300 to 900
: 0 to 1V DC -1999 to 9999
: 0 to 5V DC -1999 to 9999
: 1 to 5V DC -1999 to 9999
: 0 to 10V DC -1999 to 9999
key.
, keys.
, keys.
, keys.
, keys.
, keys.
, keys.
, keys.
, keys.
, keys.
, keys.
, keys.
, keys.
Heat/Cool control option is added
, keys.
, keys.
, keys.
， or
, keys.
or
，
Alarm type
(High limit alarm): The alarm action is a
The alarm is activated if the input value reaches the high limit alarm value.
(Low limit alarm): The alarm action is a
alarm is activated if the input value goes under the low limit alarm value.
(High/Low limits alarm): Combines High limit and Low limit alarm actions. When
input value reaches high limit alarm value or goes under the low limit alarm
value, the alarm is activated.
(High/Low limit range alarm): When input value is between the high limit alarm
value and low limit alarm value, the alarm is activated.
(Process high alarm)
，
of the controller, alarm action points can be set at random and if the input
reaches the randomly set action point, the alarm is activated.
(High limit alarm with standby),
(High/Low limits alarm with standby)
When the power to the controller is turned on, even if the input enters the
alarm action range, the alarm is not activated. (If the controller is allowed
to keep running, once the input exceeds the alarm action point, the standby
function will be released.)
(Timer function): If external signal enters, timer counting starts, and the action
selected during Delay action type selection is outputted after the set delay
time has elapsed.
(Pattern end output): When the program ends normally, pattern end output is
turned on. The output is maintained until it is released with the
(3)
A1 action delayed
timer
, Set value
PV/SV
A2 action delayed
timer
, Set value
PV/SV
(4)
Alarm HOLD function
, Selection
PV/SV
Delay action type
selection
, Selection
PV/SV
Delay time
, Set value
PV/SV
Direct/Reverse control
, Selection
PV/SV
AT bias
, Set value
PV/SV
Setting item not used
, Set value
PV/SV
OUT/OFF key function
, Selection
PV/SV
Step time unit
, Selection
PV/SV
DI (Digital input) function
, Selection
PV/SV
Output status selection
when input abnormal
, Selection
PV/SV
Controller/Converter
, Selection
PV/SV
Reverts to the PV/SV display.
21
deviation setting from the SV.
deviation setting from the SV. The
(Process low alarm): Within the scale range
(Low limit alarm with standby)
• Set the value with the ,
• Not available if
，
is selected during A1 type selection
• Set the value with the ,
• Not available if
，
is selected during A2 type selection
• Make a selection with the ,
• Common setting item for A1 and A2
Not available if ，
is selected during A1 or A2 type selection.
• Make a selection with the ,
• Available only when is selected during
A1 or A2 type selection.
• Set the value with the ,
• Available only when is selected during
A1 or A2 type selection.
• Make a selection with the ,
• Default value: (Reverse control action)
• Set the value with the ,
• Not available for DC input.
• Do not set this item even if
on the PV/SV display.
• Make a selection with the ,
• Selects fixed value control or program control.
• Make a selection with the ,
• Not available if is selected during
OUT/OFF key function selection
• Make a selection with the ,
• Not available if Serial communication option is added
• Make a selection with the ,
• Available only for DC current output type with
DC input
• Make a selection with the ,
• Available only for DC current output type
key.
keys.
or
keys.
or
keys.
or
keys.
keys.
keys.
keys.
is indicated
keys.
keys.
keys.
keys.
keys.