Table of Contents
Advertisement
11. General settings
11-5. Demonstration mode setting
You can turn on/off the demonstration mode.
1
Press [Control] knob.
Enters the Function setting mode.
2
Select "DEMO Mode" using [Control] knob.
For how to use [Control] knob, refer to <3-3. How
to select the item> (page 9).
3
Select a setting ("ON" or "OFF") using [Control]
knob.
Returns to the previous item.
Exiting from the Function setting mode
Press and hold [1/6].
11-6. Initial settings
You can configure initial settings of this unit.
1
Press [SRC] and select a Standby ("STANDBY")
using [Control] knob.
Refer to <Source selection> (page 10).
2
Press [Control] knob.
Enters the Function setting mode.
3
Select "Initial Settings" using [Control] knob.
For how to use [Control] knob, refer to <3-3. How
to select the item> (page 9).
4
Select an Initial setting item using [Control]
knob.
Display
Description
"SRC Select"
Set source selection method.
"1": The source switches each time [SRC] is
pressed.
"2": Press [SRC], Turn [Control] knob to select
the source, and then press [Control] knob to
determine it.
"Key Beep"
Setting the operation check sound (beep
sound) ON/OFF.
"ON" / "OFF"
"Function Language"
Changes the display language of items
displayed in the Function setting mode.
"English" / "Français" / "Español"
"Pandora Source"
Sets whether to display Pandora during source
selection.
"ON" / "OFF"
"iHeartRADIO Source" Sets whether to display iHeartRadio during
source selection.
"ON" / "OFF"
"Built-in AUX"
Sets whether to display AUX during source
selection.
"ON" / "OFF"
34
|
KDC-610U
"CD Read"
Sets the method for reading CD.
When unable to play a special format CD, set
this setting to "2" to force playing. Note that
some music CDs may be unplayable even
when set to "2".
In addition, audio files cannot be played when
set to "2". Normally, keep this set to "1".
1: Automatically distinguishes between the
audio file disc and music CD when playing
a disc.
2: Forces playing as a music CD.
"TAG Transfer Setup"
When iPods are connected to both the front
and rear USB terminals, select the iPod to
which the tag stored through iTunes tagging is
to be transferred.
"FRONT" / "REAR"
"Built-in AMP"
Selecting "OFF" turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
"ON" / "OFF"
"Speaker Select"
Sets the speaker type so that the System Q
value is optimal.
"OFF": OFF
"5/4inch": For 5 & 4 in. speaker
"6x9/6inch": For 6 & 6x9 in. speaker
"O.E.M.": For the OEM speaker
"F/W Update"
Upgrades the firmware.
Selecting "YES" and then pressing [Control]
knob starts upgrading the firmware.
For how to update the firmware, access our
web site.
www.kenwood.com/cs/ce/
(Colored text: Factory setting)
5
Select a setting using [Control] knob.
Returns to the previous item.
Exiting from the Function setting mode
Press and hold [1/6].
12. SiriusXM™ Satellite Radio (optional tuner and service required)
12-1. Before use
• SiriusXM Satellite Radio operation requires the
connection of the optional SiriusXM-Connect
Vehicle Tuner. To activate the SiriusXM Vehicle
Connect tuner, you will need the Radio ID.
Make a note of your Radio ID
For each SiriusXM Vehicle Connect tuner, a unique
Radio ID is assigned. To confirm your Radio ID, tune
to channel 0. The letters I, O, S and F are not used in
any Radio ID.
The Radio ID is also located on the label of the
SiriusXM Connect Vehicle Tuner.
How to activate your SiriusXM Service
Go to www.siriusxm.com/activatenow or call 1-866-
635-2349 to activate your SiriusXM Vehicle Connect
Tuner.
To activate SiriusXM Canada service go to www.
xmradio.ca and click on "ACTIVATE RADIO" in the top
right corner, or call 1-877-438-9677
12-2. Listening to the SiriusXM™
Satellite Radio
Selecting a tuner source
1
Press [SRC].
Enters the Source selection mode.
2
Select a SiriusXM ("SiriusXM") source using
[Control] knob.
Selecting a channel
Press [E] or [F].
The seek mode can be changed. Refer to
<Selecting a Seek mode> (refer to below).
Selecting a Seek mode
Press [S].
Display
Operation
"Channel"
Normal manual seeking.
"Preset"
Searches in order of the channels in the preset memory.
Channel preset memory
1
Press [E] or [F] to select the channel.
2
Press [1/6] twice.
3
Turn [Control] knob to select a memory
number ("1" – "24").
4
Press and hold [Control] knob.
Recalling the channels in the memory
1
Press [1/6] twice.
2
Select a preset number ("1" – "24") using
[Control] knob.
About Smart Favorites
• Data for Replay is automatically stored in the station
memory number 1 though 6. (Smart Favorites function)
Smart Favorites brings the following experience;
- Can replay the long duration of radio content stored
immediately after tuning in to the station registered to
the station preset memory. (refer to <12-17. SiriusXM
Replay™> (page 40))
- Tune Start™ (refer to <12-6. Tune Start™> (page 36))
However, the Smart Favorites function may not be available
depending on the system configuration.
In this case, the "Tune Start" items do not appear on the
Function setting. Refer to <12-20. SiriusXM tuner setting>
(page 41).
|
English
35
Hide quick links:
Advertisement
Table of Contents
