Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric NM-IP1100M
Summary of Contents for Mitsubishi Electric NM-IP1100M
-
Page 1: Installation Guide
NM-IP1100M Installation Guide... - Page 2 INFORMATION TO USER CAUTION RISK OF ELECTRIC SHOCK, DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SEERIVCE PERSONEL. This symbol is intended to alert the user to the presence of un‐insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating ...
-
Page 3: Table Of Contents
NM‐IP1100M Table of Contents 1. FEATURES ....................... 4 2. PACKAGE CONTENTS ....................5 3. PART NAMES ......................6 3.1. Rear View ........................... 6 3.2. Bottom View........................6 4. INSTALLATION ......................8 4.1. Installing a C/CS Mounting lens..................8 4.2. Setting the Image Attribute....................8 4.3. Installing a Wireless USB Adapter (Optional)..............9 5. CONNECTIONS ...................... 10 5.1.Connectors ........................11 6. CONFIGURATION ....................14 6.1.Set up network environment .................... 14 6.2. View video on web page .................... -
Page 4: Features
NM‐IP1100M 1. FEATURES Camera • Box type IP Megapixel Camera • Aptina (Micron) 1/3.2" (4:3) CMOS 2M pixels Streaming • Dual streaming mode (such as different codec/resolution/bit rate and so on.) • De‐interlacing on DSP • Burnt‐in text supported • Unicast/Multicast supported Video/Audio • Megapixel Compression: H.264, MJPEG, Up to 1600 x 1200 • Video compression: H.264/MPEG/MJPEG (Dual Stream@D1) • Audio compression: G.711(µLaw, aLaw)/PCM • Video Motion Detection supported • 2‐way mono audio supported Network • RTSP/ HTTP protocol supported • 10/100 Base‐T Ethernet Additional Features • RS‐485 supported ... -
Page 5: Package Contents
NM‐IP1100M 2. PACKAGE CONTENTS Unpack carefully and handle the equipment with care. The packaging contains: Camera DC power adaptor Mount ring 9 Pin terminal block Rubber cap (for protecting CCD) Hex wrench driver Adaptor for mounting the camera Screws Quick Installation Guide DC Jack Adaptor Cable The above contents are subject to change without prior notice. Note 5 ... -
Page 6: Part Names
NM‐IP1100M 3. PART NAMES 3.1. Rear View ○ 1 ○ 2 RESET RS-485 DO AUDIO ○ 4 ○ 3 - + C 1 C 1 Out In ○ 5 Micro SD ETHERNET ○ 6 3.2. Bottom View ... - Page 7 NM‐IP1100M Reset Reset switch is used for restarting or resetting the camera as Factory Default (FD). Refer to the section “6.3. Reset” for more specific information. USB connector Insert a USB storage device or Wi‐Fi devices. (Ralink RT73 or RT3070 chipset based wireless device is available.) 9 pin terminal block for D/I, D/O, audio, and serial communication Refer to the section “5.1.Connectors” for more specific information. Power Adaptor Connector (DC 12V) The camera needs a DC12V for power supply. Refer to the section “Power Adaptor Connector (DC 12V)” for more specific information. + ‐ Make sure the polarity is correct. Incorrect connection may cause malfunction or damage to the IP device. ...
-
Page 8: Installation
NM‐IP1100M 4. INSTALLATION CCW Set Screw SET SCREW *Lens is optional. We recommend that use a megapixel lens with manual iris to support the full resolution of megapixel camera. Note 4.1. Installing a C/CS Mounting lens 1. Remove the protective rubber cap from the front of the camera. 2. Install the mount ring for lens and adjust the mount ring to fit C or CS lens. 3. Tighten the setscrews using the hex wrench in the package. 4.2. Setting the Image Attribute You can set the image attribute of camera through the webpage. The menu of image attribute can be seen under Setup > Video & Audio > Video‐in > Image Signal Processing. The following features can be adjusted: • Brightness ... -
Page 9: Installing A Wireless Usb Adapter (Optional)
NM‐IP1100M 4.3. Installing a Wireless USB Adapter (Optional) A wireless USB adapter is sold separately as an optional kit. Please contact UDP Technology Ltd. to purchase a wireless USB adapter. Note The kit includes: • USB cable • 3M Double‐coated tape • Wireless USB adapter Perform the following steps to install a wireless USB adapter: 1. Connect one end of the USB cable to the camera. 2. Connect the other end of the USB cable to a wireless USB adapter. 3. Use the enclosed double‐coated tape to attach the wireless USB adapter to the desired area. You can attach the adapter on the body (side, top, or bottom) of the camera, ceiling, or wall. 9 ... -
Page 10: Connections
NM‐IP1100M 5. CONNECTIONS DC Jack Adaptor RESET RS-485 AUDIO - + C 1 Out In Micro SD Power Adaptor LAN Cable ETHERNET When connecting the DC power supply, make sure the polarity is correct. Incorrect connection may cause malfunction or damage to the camera. Caution 10 ... -
Page 11: Connectors
NM‐IP1100M 5.1.Connectors 9 pin terminal block RESE T RS-485 DO DI AUDI O C 1 C 1 In ut Micro SD ETHERN ET RS‐485 The RS‐485 serial port consists of TRX+(RX+) and TRX‐(RX‐) as following the following image. <RS-485 Application> TRX+(RX+) TRX-(RX-) 485 Devices PTZ Device RS‐485 Connection Sensor (DI) connection The camera provides 1 channel D/I. It can be connected to either a voltage type sensor or a relay type sensor as the following figures. It can be selected by software. ... - Page 12 NM‐IP1100M Internal +5V Internal Output of Output of Sensor Sensor DI DI 1 ‐ ‐ COM + ‐ COM Relay Type Voltage Type Alarm (DO) connection Only the relay type is supported. Relay Rating: Max 24VAC 500mA or 12VDC 1A Do not exceed the maximum relay rating. Caution Internal Device Relay Type Audio connection The camera has a mono audio input and a mono audio output. As the output power for the audio is low, amplifier speaker is needed. (Do not use a headphone or earphone directly to the camera.) Aout ...
- Page 13 NM‐IP1100M Power Adaptor Connector (DC 12V) Power adaptor connector connects to DC Jack adapter cable. ‐ + ‐ RED Make sure the polarity is correct. Incorrect connection may cause malfunction or damage to the IP device Caution Power Adaptor Connector (DC 12V) Caution 13 ...
-
Page 14: Configuration
NM‐IP1100M 6. CONFIGURATION 6.1.Set up network environment The default IP address of your IP device is 192.168.XXX.XXX. You can find the available IP address from the MAC address of your device. Please make sure the device and your PC are on the same network segment before running the installation. If the network segment between your PC and the device is different, change your PC’s settings as below. IP address : 192.168.xxx.xxx Subnet mask: 255.255.0.0 6.2. View video on web page View the live video on a web page using your IP device and its IP address. You can use the IPAdminTool or enter the IP address on the web page. ... - Page 15 NM‐IP1100M To use the IPAdminTool and view the live video on a web page: 1. Start IPAdminTool. Names and info of currently activated devices appear as a list. 2. Right‐click on the desired device and select Web view. 3. Select Continue to this website on the Security Certificate Alert page. (The explanation and captured images at this manual are mainly on the basis of Internet Explorer 7.0) 4. Click pop‐up blocked and install the ActiveX control by clicking the Install button. You need to install the ActiveX for displaying the images. 15 ...
- Page 16 NM‐IP1100M 5. Wait for a few seconds while the web page loads. Then the live video is displayed on the main page of the web browser. 6. If the live video is not displayed and “Can not Create XMLDOMDocument Install MSXML4.0” message is shown as below, please download and Install from the link below. http://www.microsoft.com/downloads/details.aspx?familyid=3144B72B‐B4F2‐46DA‐ B4B6‐C5D7485F2B42&displaylang=en (VCA Library requires MS XML 4.0 library which is an xml parser made by Microsoft.) 16 ...
-
Page 17: View Video Using Ip Address
NM‐IP1100M 6.2.2. View video using IP address View the live video on a web page using your IP device and its IP address. To have the correct IP address ready and use it on a web page: 1. Convert a MAC address to an IP address or check the IP address on the IPAdminTool. (The MAC address is attached on the side or bottom of the device.) MAC address = 00‐13‐23‐01‐14‐B1 → IP address = 192.168.20.177 the Hexadecimal number to Decimal number. 2. Open a web browser and enter the IP address of the device. 3. Click Continue to this website on the Security Certificate Alert page. 4. Click pop‐up blocked and install the ActiveX control. You need to install the ActiveX for displaying the images. 5. -
Page 18: Appendix (A): Specifications
NM‐IP1100M APPENDIX (A): SPECIFICATIONS Summary Camera Module Image Sensor Aptina (Micron) 1/3.2" (4:3) CMOS 2M Effective Pixels 1600 x 1200 (UXGA, 2M) Scanning system Progressive Scan Dynamic Range 71dB SNR Max 42.3dB Minimum Illumination 0.5 Lux(50IRE), 0.1 Lux(DSS x5 ON) Lens (Optional) 3~8 mm, F1.0 Manual Iris Lens, CS Mount Day & Night S/W Video Megapixel Compression H.264 and MJPEG Compression Format H.264, MPEG‐4, and MJPEG Number of Streams Dual Stream, Configurable Resolution See Resolutions table below 5 fps@UXGA (1600 x 1200) Compression FPS 8 fps@SXGA (1280 x 1024) H.264 (In case of VCA or Burnt In 12 fps@HD720 (1280 x 720) ... -
Page 19: Resolutions Per Codec Frame Rate
NM‐IP1100M Resolutions per Codec Frame rate Codec MPEG4 H.264 MJPEG Resolution UXGA (1600x1200) Not available 5 fps SXGA (1280x1024) Not available 8 fps HD720 (1280x720) Not available 12 fps XGA (1024x768) Not available D1 (720x) 15 fps 4CIF (704x) VGA (640x) 15 fps 15 fps CIF (352x) QVGA (320x) QCIF (176x) Electrical Characteristics Audio Input Linein, 1.43Vp‐p(Min 1.35Vp‐p, max 1.49 Vp‐p), 39 KΩ Audio Output Lineout, 46mW Power, 16 Ω ... -
Page 20: Vca (Video Content Analysis)
NM‐IP1100M VCA (Video Content Analysis) VCA Presence (Included as Standard) High Performance Advanced Tracking Algorithm, Low False Alarm Rate Easy to Use Intuitive Web Browser Interface Detection Zones Multi‐segment Polygons and Lines On‐screen Display Real‐time Display of Tracking Data and Events Burnt‐in Annotation Stream VCA Surveillance (Option) Camera Tampering, Direction, Stopping, Loitering, Entering, Detection Behavior Exiting, Appear, and Disappear Filters 3D Behavior Perspective Corrected Size and Speed Filters Statistics Counting Functions and Other Statistics Meta Data Binary XML Format Image Stabilization (Option) Electronic Stabilization Removes Camera Sway 20 ... -
Page 21: Appendix (B): Power Over Ethernet
NM‐IP1100M APPENDIX (B): POWER OVER ETHERNET The Power over Ethernet(PoE) is designed to extract power from a conventional twisted pair Category 5 Ethernet cable, conforming to the IEEE 802.3af Power‐over‐Ethernet (PoE) standard. IEEE 802.3af allows for two power options for Category 5 cables. The PoE module signature and control circuit provides the PoE compatibility signature and power classification required by the Power Sourcing Equipment (PSE) before applying up to 15W power to the port. The high efficiency DC/DC converter operates over a wide input voltage range and provides a regulated low ripple and low noise output. The DC/DC converter also has built‐in overload and short‐circuit output protection. ... -
Page 22: Appendix (C): Dimensions
NM‐IP1100M APPENDIX (C): DIMENSIONS 55 Front view Top view RESET RS-485 DI AUDIO - + C 1 C 1 Out In Micro SD ETHERNET Rear view H.264 Megapixel IP Camera Right side view UNIT: mm 22 ... -
Page 23: Revision History
NM‐IP1100M REVISION HISTORY MAN# DATE(M/D/Y) Comments 01A.01 01/11/2010 Created. 01B.00 01/22/2010 Fixed Resolution table 01B.01 02/25/2010 Modified for end users 01B.02 04/05/2010 Added LAN cable specification for PoE 02A.00 04/20/2010 FW v1.02.04 updated 02A.01 05/14/2010 Added a notice about AVI recording feature via SD card slot 23 ...