Contens 1. Precautions 2. Product specifications 3. Disassembly and Reassemble 4. Troubleshooting 5. Exploded View & Part List 6. Wiring Diagram P2070H / P2270H Refer to the service manual in the GSPN (see the rear cover) for the more information.
3. Disassembly and Assembly 3. Disassembly and Assembly This section describes the disassembly and reassembly sequences for this monitor. Warning: As this monitor has parts that are sensitive to static electricity, be careful when handling them. 3-1. Disassembly Caution: 1. Turn the monitor off before beginning the disassembly process. 2.
Page 5
3. Disassembly and Assembly Description Photo Screws 3. Separate the other side in the same way. 4. Lift the REAR-COVER up to separate it. 5. Remove the FFC cable, the LED driver wire, the function wire and the two hex-head screws, and separate the DVI shield.
Page 6
3. Disassembly and Assembly Description Photo Screws 7. Separate the inverter and the main PBA from the PBA bracket. P2070H P2270H ※The assembly is in the reverse order of disassembly.
1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1. Precautions 1-2. Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1. Precautions 1-4. Installation Precautions For safety reasons, more than two people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
2. Product specifications 2-2. Spec Comparison to the Old Models Model P2070H / P2270H T (T240) Design 20” 250cd/m2 Brightness 300cd/m2 22” 300cd/m2 Contrast 1000:1 1000:1 20” 50,000:1 20,000:1 22” 70,000:1 Response Time 5ms ( W to B) & 2ms (G to G)
• When the raster does not appear: Function PBA, Main PBA, Inverter, Adapter • When 5V is generated but a blank screen is displayed : Main PBA • When 12V (P2070H) / 14V (P2270H) is not Generated : Adapter “Press the MENU button and hold down the, “...
4. Troubleshooting 4-2. When the power does Not Turn on - When turning on the power button after connecting Adaptor, the LED at the front of the monitor Symptom does not operate. - Check the Adaptor power fuse and the Adaptor output power. - Check the connections for Adaptor and the Main board inside the monitor.
Page 30
4. Troubleshooting 4-2-1. Circuit diagrams when the power does not turn on...
4. Troubleshooting 4-3. When the screen is blank (Analog) - Even though the LED power turns on, the screen is blank when connecting the DVI-I to D-sub Symptom cable. - Check the DVI-I to D-sub cable connections. Major checkpoints - Check whether the LVDS(FFC) cable is connected correctly to the panel. - Check whether the lamp connector of the panel is connected correctly to the Inverter.
Page 32
4. Troubleshooting 4-3-1. When a blank screen is displayed (Analog)
Page 33
4. Troubleshooting 4-3-2. Waveforms when no screen is displayed (Analog) ① ③ ④...
4. Troubleshooting 4-4. When a blank screen is displayed (Digital) Symptom - Even though the LED power turns on, the screen is blank when connecting the DVI cable. - Check the DVI cable connections. Major checkpoints - Check whether the LVDS(FFC) cable is connected correctly to the panel. - Check whether the lamp connector of the panel is connected correctly to the Inverter.
Page 35
4. Troubleshooting 4-4-1. Circuit diagrams when a blank screen is displayed (Digital)
Page 36
4. Troubleshooting 4-4-2. Waveforms when a blank screen is displayed (Digital)
4. Troubleshooting 4-5. When a blank screen is displayed (HDMI) Symptom - Even though the LED power turns on, the screen is blank when connecting the HDMI cable. - Check the HDMI cable connections. Major checkpoints - Check whether the LVDS(FFC) cable is connected correctly to the panel. - Check whether the lamp connector of the panel is connected correctly to the Inverter.
Page 38
4. Troubleshooting 4-5-1. Circuit diagrams when a blank screen is displayed (HDMI) 4-11...
Page 39
4. Troubleshooting 4-5-2. Waveforms when a blank screen is displayed (HDMI) 4-12...
4. Troubleshooting 4-6. Error Examples and Actions Error Appearance Symptoms and Actions Remarks Symptom: DVI signals are not recognized. *On how to input DDC, refer to the training manual. Cause: This error occurs because the PC cannot recognize the mode information since the DVI DDC is not input to the monitor.
1) Use when updating the AD board code. 2) Download the WinDDC program, DDC Input program, and Hex and DDC files appropriate to the model through the Quality Control department of Samsung Electronics. Install the jig and input the data, as shown in the figure. Monitor needing...
Page 42
4. Troubleshooting 4-7-2. Service Function Specifications Checking the Code Version 1. Check the MCU code version and checksum after entering SVC Mode. 2. Entering SVC Mode - Adjust the Brightness and Contrast values to 0. - Hold down the Enter button for five (5) seconds. - The SVC Function OSD is displayed.
Page 43
4. Troubleshooting When replacing the panel After replacing the panel, select the Panel Ch. No. item and press the MENU key for five seconds. The Panel Ch. No. will then increment by one and the panel’s time information will be set to 0. At the same time, the panel cycle will be set to 0.
Page 44
DDC MANAGER Connect to MAIN board CN102 - Connect DDC Manager Jig to P2070H / P2270H with DVI-I to D-Sub cable and DVI cable. - Execute Winddc.exe Program on PC. - Click the Winddc icon. 1. Click the Open [F5] icon 2.
Page 45
4. Troubleshooting 5. Enter the serial number and then press the Enter button. If you using old version. -> When inputting digital data after inputting analog data, repeat steps 2 to 5. 4-18...
Page 46
4. Troubleshooting Inputting the MCU Data 1) Check the following options. - Manufacture : MSTAR - Device Type :TSUMxx - Communication Por t: DSUB15(Analog) - External Memory : PMC25LV020 2) Click the LoadFile button, select an MCU code file, and then click the Open [O] button. 4-19...
Page 47
4. Troubleshooting 3) Click the Auto Program button. 4) When programming and verification are complete, hard power the monitor off and then on again. 4-20...
Page 48
4. Troubleshooting Inputting the Code (HDCP) 1. Run the service.exe file. 2. Click the HDCP button. 4-21...
Page 49
4. Troubleshooting 3. Click the HDCP Write button and select MStar_HDCPKEY. 4. Inputting the HDCP key is completed. 4-22...
* Upon occurrence of a fault: No Digital Output (No TMDS output) error may occur. CN700 Supplies 14V (12V for P2070H) from the adapter to the main board. * Upon occurrence of a fault: No Power and Blank Screen errors may occur.