Broseley Winchester Installation And Operation Manual
  1. Manuals
  2. Brands
  3. Broseley Manuals
  4. Stove
  5. WINCHESTER
  6. Installation and operation manual

Broseley Winchester Installation And Operation Manual

Gas stove
Hide thumbs Also See for Winchester:
Table of Contents

Advertisement

Quick Links

Download this manual
Installation and Operation Manual
Winchester
Gas Stove
Revision: 200707_2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Winchester and is the answer not in the manual?

Questions and answers

Related Manuals for Broseley Winchester

Summary of Contents for Broseley Winchester

  • Page 1 Installation and Operation Manual Winchester Gas Stove Revision: 200707_2...

  • Page 2: Table Of Contents

    Page 2 of 20 The Winchester Gas Stove Installation, Servicing and User Instructions. Technical Information Natural Gas Propane G20/1 G31/I Heat Input (Gross) 6.9 kW/hr 6.9kW/hr Supply Pressure 20 mbar 37mbar Gas Rate 0.66 M 0.25M Injector Size Contents Page...
  • Page 3 Page 3 of 20 Winchester Gas Dimensions Height 595mm Height to centre of rear flue spigot 455mm Depth 465mm Width 590mm Centre of top flue to rear of stove 150mm Flue spigot diameter 127mm Weight 116kg Maximum heat output (approx.)

  • Page 4: Important Information

    Page 4 of 20 THANK YOU FOR PURCHASING A GAS FIRED STOVE Broseley Fires Ltd, a family run company, was founded as an appliance and design development company in 1975. Since then we have built up an enviable reputation for the quality, reliability and fuel efficiency of our stoves.
  • Page 5 Page 5 of 20 SITING THE APPLIANCE The gas supply connection to the appliance is at the rear right hand side. The connection requires an 8mm-diameter semi-rigid pipe, not more than 1 metre in length. The appliance can be installed in any adequate area suitable for solid fuel fires and stoves.
  • Page 6 Page 6 of 20 Before installing the stove, ensure the gas to be used i.e. natural (Mains) gas or LPG (Propane) corresponds with the identification plate on the burner. Unscrew the M6 x 18 Hex Bolt and open the main stove door to retrieve the box containing the 4 Legs, Handle and Allen Key.

  • Page 7: Flue Connection / Ventilation

    An adapter may well be required to do this. Please note: Broseley Fires do not provide flue pipes or accessories, please consult your flue pipe provider or local builders / plumber merchants for a suitable adapter.
  • Page 8 Page 8 of 20 GAS CONNECTION A minimum 15mm-diameter gas supply pipe must be used to within 1 metre of the installation with the final connection to the stove to be completed with the suitable 8mm semi-rigid gas pipe. The 8mm pipe should be connected to the inlet of the gas valve using the nut and 8mm olive provided.
  • Page 9 Replacement ceramics are available from your dealer. Whilst arranging the ceramics, ensure that the pilot is not obstructed. Broseley Fires Ltd accepts no responsibility for any injury sustained whilst handling hot ceramics. Before any ceramics are placed in position ensure that the burner is operating correctly.
  • Page 10 Page 10 of 20 IMPORTANT Please follow these instructions carefully. Ceramics that are positioned wrongly could seriously alter the performance of your appliance. Winchester Coal Fitting Instructions Stage 1 Stage 2 Stage 3 Stage 4...
  • Page 11 Page 11 of 20 Log Ceramic Fitting Instructions THE CERAMIC LOGS HAVE LOCATION POINTS ON THEM THAT WILL HELP YOU LOCATE THEM IN THE CORRECT POSITION. PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY AND USE THE DIAGRAMS TO ASSIST YOU. Stage 1 Position the largest ceramic on top of the burner and push it firmly against the rear of the stove.

  • Page 12: Extinguishing The Stove Fully

    Page 12 of 20 OPERATING THE STOVE It is important to read these instructions thoroughly before lighting the stove. The gas stove operates with a traditional permanent pilot light. The knobs for ignition and power control are located on the lower right hand side of the stove.

  • Page 13: The Remote Control

    Page 13 of 20 THE REMOTE CONTROL POSITIONING THE RECEIVER After fitting the batteries in the receiver and the hand set, place the receiver anywhere on the hearth. There is a long lead on the receiver to allow you to position the receiver towards the front of the hearth, if you wish to see the light come on when the handset is in use.
  • Page 14 Page 14 of 20 Transmitter Function Set the Display • After connecting the battery or by simultaneously pressing AUTO and TIMER, the display flashes. You are in set mode. • From set mode, press AUTO to switch from °F (and 12 hour clock) to °C (and 24 hour clock) or vice versa.
  • Page 15 Page 15 of 20 • Briefly press AUTO. The set temperature will appear briefly before the display reverts to the room temperature. Timer Mode (TIMER in display) • During heating periods P1* and P2*, the temperature is controlled in the same manner as in automatic mode.

  • Page 16: Test For Spillage / Monitoring

    Page 16 of 20 TEST FOR SPILLAGE A Spillage Test MUST be made before the installed fire is left with the customer. Carry out the test by first closing all doors and windows in the room containing the fire. Insure that the fire is burning at full rate for a minimum of 10-15 minutes. Using a lighted smoke match run it along the top edge of the draught diverter on the rear of the stove, observing the smoke being drawn into the dilution box, after 10 minutes repeat the test...
  • Page 17 Page 17 of 20 TROUBLESHOOTING THE GAS PILOT WILL NOT IGNITE OR STAY LIT • Ensure the gas is turned on at the appliance and the meter / cylinder. • Hold the pilot gas button for at lest 20 seconds once the pilot is alight to ensure the operation of the safety thermocouple valve.
  • Page 18 Page 18 of 20 • Check the condition of the coals. Any damaged ones will affect the efficient operation of the stove and should be replaced with new ones available from your stove supplier. • All gas supply joints should be checked to make sure they are completely sealed and that the gas supply and pressure is to specification.

  • Page 19: Specification And Information

    Page 19 of 20 SPECIFICATION & INFORMATION THIS SECTION TO BE COMPLETED AND SIGNED BY THE INSTALLATION ENGINEER Type gas supply (please tick) Natural (mains) Gas LPG supply in bulk LPG supply in cylinder Size of Governor setting: (i.e.) Natural Gas 20mbar. LPG 37mbar) Length and size of gas supply: Meter pressure Fire on only: Other appliances, All on:...

  • Page 20: Guarantee

    The rights given in this guarantee are limited to the UK mainland and are in addition to any to which you may have a statutory entitlement. Please retain your purchase receipt. We will need to see this in the event of a claim under warranty. Broseley Fires Ltd Knights Way Battlefield Enterprise Park Shrewsbury...

Table of Contents