1. Manuals
  2. Brands
  3. JVC Manuals
  4. VCR
  5. HR-S8009UM
  6. Instructions manual

JVC HR-S8009UM Instructions Manual

Jvc video cassette recorder instructions
Hide thumbs
Table of Contents

Advertisement

Quick Links

/37$
&23<5,*+7 ‹  9,&725 &203$1< 2) -$3$1 /7'
Dear Customer,
Thank you for purchasing the JVC VHS video cassette recorder.
Before use, please read the safety information and precautions to
ensure safe use of your new VCR.
CAUTIONS
WARNING: DANGEROUS VOLTAGE INSIDE
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
The POWER 1 button does not completely shut off mains
power from the unit, but switches operating current on and off.
"`" shows electrical power standby and " ! " shows ON.
This unit is produced to comply with Standard IEC 60065.
POWER SYSTEM:
This set operates on voltage of AC 110 – 220Vd, 50/60 Hz
with automatic switching.
Use the conversion plug (provided) depending on the type of
your AC WALL outlet.
The rating plate and safety caution are on the rear of the unit.
IMPORTANT:
It may be unlawful to record or play back copyrighted material
without the consent of the copyright owner.
9,'(2 &$66(77( 5(&25'(5
+5680
— 1 —
,16758&7,216
CAUTION
When you are not using the VCR for a long period of time, it
is recommended that you disconnect the power cord from the
AC outlet.
Dangerous voltage inside. Refer internal servicing to qualified
service personnel. To prevent electric shock or fire hazard,
remove the power cord from the AC outlet prior to
connecting or disconnecting any signal lead or aerial.
Changes or modifications not approved by JVC could void
user's authority to operate the equipment.
Caution on Replaceable lithium battery
The battery used in this device may present a fire or chemical
burn hazard if mistreated. Do not recharge, disassemble, heat
above 100°C or incinerate.
Replace battery with Panasonic (Matsushita Electric), Sanyo,
Sony or Maxell CR2025. Danger of explosion or Risk of fire if
the battery is incorrectly replaced.
Dispose of used battery promptly.
Keep away from children.
Do not disassemble and do not dispose of in fire.
● Cassettes marked "S-VHS" and "VHS" can be used with this
video cassette recorder. However, S-VHS recordings are
possible only with cassettes marked "S-VHS".
By using S-VHS ET it is possible to record and play back with
S-VHS picture quality on VHS cassettes with this VCR.
3ULQWHG LQ &KLQD
 019f3-f%-

Advertisement

Table of Contents
loading

Related Manuals for JVC HR-S8009UM

Summary of Contents for JVC HR-S8009UM

  • Page 1 /37$ &23<5,*+7 ‹  9,&725 &203$1< 2) -$3$1 /7' Dear Customer, Thank you for purchasing the JVC VHS video cassette recorder. Before use, please read the safety information and precautions to ensure safe use of your new VCR. CAUTIONS WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
  • Page 2 Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the VCR’s power turned on for a few hours to let the moisture dry. How to use the Remote...

  • Page 3: Buttons, Connectors And Indicators

    VIDEO/AUDIO input connectors Display panel Play indicator Record indicator Rear Panel AC power cord Cassette loading slot Remote sensor Timer mode indicator Channel and auxiliary input/Clock time Lithium battery compartment — 3 — VCR mode indicator S-VHS mode indicator S-VIDEO...

  • Page 4: On-Screen Display

    If you press OK on the Remote when “SUPERIMPOSE” is set to “ON”( pg. 12), you can see the current VCR status on the TV screen. To clear the time counter, press OK again. The indications are not recorded even if the VCR is in the recording mode.

  • Page 5: Basic Connections

    S-VIDEO Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. If you connect the TV and the VCR only using the RF connection, press TV/VCR on the Remote so that the VCR mode indicator lights on the display panel.

  • Page 6: Initial Settings

    “SCAN COMPLETED” will be displayed on the screen. If “SCAN COMPLETED–NO SIGNAL–” is displayed on the screen, make sure that the antenna cable is connected to the VCR properly and press OK or on the Remote. The VCR will try Auto Channel Set again.

  • Page 7: Tuner Setting

    AUTO CHANNEL SET Do not apply too much pressure when inserting. MANUAL CHANNEL SET The VCR turns on, and the counter on the on-screen display is reset, automatically. SELECT WITH ( , ) AND (OK) If the cassette’s record safety tab has been removed, playback PRESS (MENU) TO END begins automatically.

  • Page 8: Playback Features

    Locating beginning of timer recordings — Instant Review After ensuring that the VCR is turned off and that the timer mode is disengaged, press REVIEW on the Remote. The VCR turns on, and rewinds to the index code indicating the beginning of the last timer-recorded program, then begins playback automatically.

  • Page 9: Recording Features

    If the tape reaches its end during recording, the recording stops and “ ” and “ $” on the display panel blink. Press STOP/EJECT (0) on the VCR to eject the cassette or press REW (3) on the Remote to rewind the tape. Recording Features Specifying recording length —...

  • Page 10: Express Timer Programing

    To use the VCR while it is in timer recording standby mode Press #, then press 1. After you use the VCR, press # again to put the VCR into timer recording standby mode. Checking, canceling or changing...

  • Page 11: Program Overlap Warning Display

    5 minutes if you are not in the timer recording standby mode at that time. Press # to put the VCR into timer recording standby mode. To clear the display, press & (CANCEL) on the Remote.

  • Page 12: Function Settings

    (on-screen display) appears on the screen. NOTE: When you use this VCR as the playback VCR for editing a tape, be sure to set this function to “OFF”; otherwise, the VCR status information (on-screen display) will be recorded on the edited See below) tape.

  • Page 13: Child Lock

    This Remote can control some functions of remote controllable TVs, cable boxes or DBS (Direct Broadcast Satellite) receivers listed below. Without setting, you can control a JVC TV. NOTES: Some unit’s brands have more than one code. If the unit does not function with a specified code, try other codes.

  • Page 14: Changing Remote Control Code

    VCR is initially set to respond to A code signals. You can easily modify your VCR and the Remote to respond to B code signals. When using two JVC VCRs, set two VCRs and their Remotes to different codes, so that you can operate these VCRs separately.
  • Page 15 Editing You can use your VCR as the playback or recording VCR. You can use a camcorder as the playback VCR and your VCR as the recording VCR. Refer also to the other components’ instruction manuals for connection and its operations.

  • Page 16: Specifications

    Specifications GENERAL Power requirement : AC 110 V – 220 V Power consumption Power on : 18 W Power off : 3.0 W Temperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (W x H x D) : 435 mm x 94 mm x 247 mm Weight : 2.7 kg Format...

Table of Contents