Bailey Unicorn 2 Service Manual page 14

Fuse MCB Specifications Chart
Fuses
Alarm
Fridge Ignition
Caravan Battery
Fridge Ignition
Caravan Battery
Lights 1
Lights 2
Ignitions
Road Lights
Front Marker Lights
Side Marker Lights (Low Level)
Side Marker Lights (High Level)
Brake Light (High Level)
Number Plate Light
Tail Light
Direction Indicator Light
Reversing Light
Brake Light (Low Level)
Fog Light
Bulb Replacement
Unicorn Tail, Indicator, reverse, brake and fog.
1. Remove the 2 fixing screws whilst supporting
the rear light. Keep the screws safely, ready
for refitting the light. Do not attempt to use
any alternative screws which could damage the
rear light or caravan panel.
2. Pull the rear light towards you from the side
with the fixing holes.
2-hooks which locate into the caravan panel
and will allow you to see the back of
light.
3. Remove the bulb holder with the failed bulb
14
5 amp (yellow)
5 amp (yellow)
15 amp (blue)
15 amp (blue)
15 amp (blue)
15 amp (blue)
15 amp (blue)
5 amp (yellow)
Bulb Type
LED
LED
R5W
LED
Festoon
R10
PY21
P21
P21
P21
from the rear light by turning the bulb holder
anti-clockwise, remove the failed bulb from the
bulb holder and fit the correct replacement.
There is a diagram on the lower part of the light
which shows the bulb type to be fitted. Replace
the bulb holder by inserting into the hole and
turn clockwise to lock into position. Ensure all
seals are correctly located.
This will release the 4. Offer the rear light back into the caravan panel,
ensure the 2-location hooks are engaged and
the rear then replace the rear light fixing screws.
Do not over tighten! Maximum torque is 80
!
Ncm
Pump
Aux Socket
Radio/Aerial
Alde Water heater
Alde central Heating
Refrigerator
Smoke Alarm Battery
CO alarm Battery
PIR alarm Battery
Bulb Rating
12v/ <1 watt
12v/ <1 watt
12v/ 5 watt
12v/ <1 watt
12v/ 10 watt
12v/ 10 watt
12v/ 21 watt
12v/ 21 watt
12v/ 21 watt
12v/ 21 watt
5. Check for correct operation of all light functions.
Pegasus GT65 Tail, Indicator, reverse, Brake and
Fog.
1. Using a Pozi-Drive screwdriver remove carefully
the screws visible on the failed lamps lens,
support the lens so it cannot fall.
Function dependant
2. For the Indicator bulb remove the bulb by
turning anticlockwise with slight pressure on
the bulb.
3. Replace Bulb with a new 12V 21W Clear Bulb
aligning the pins correctly prior to installation.
Install new bulb with slight pressure and turn
clockwise.
4. For the Stop Tail bulb remove the bulb by turning
anticlockwise with slight pressure on the bulb.
5. Replace Bulb with a new 12V 21/5W Clear Bulb
aligning the pins correctly prior to installation.
Install new bulb with slight pressure and turn
clockwise.
6. For the Fog bulb remove the bulb by turning
anticlockwise with slight pressure on the bulb.
7. Replace Bulb with a new 12V 21W Clear Bulb
aligning the pins correctly prior to installation.
Install new bulb with slight pressure and turn
clockwise.
8. For the Reverse bulb remove the bulb by turning
anticlockwise with slight pressure on the bulb.
9 Replace Bulb with a new 12V 21W Clear
Bulb aligning the pins correctly prior to installation.
Install new bulb with slight pressure and turn
clockwise.
Upper Side position lamps
1. Remove lens from base to access bulb.
2. Carefully insert a small flat head screwdriver
into the recess in the lower edge of the lamp
base. Apply pressure to the locking base.
3. Lift lens upwards and away from the lamp base,