Bailey 2002 Series Owner's Manual
  1. Manuals
  2. Brands
  3. Bailey Manuals
  4. Motorhomes
  5. 2002 Series
  6. Owner's manual

Bailey 2002 Series Owner's Manual

2002 series
Hide thumbs
Table of Contents

Advertisement

Quick Links

Bailey of Bristol
2002 Series
Owners Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2002 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Bailey 2002 Series

Summary of Contents for Bailey 2002 Series

  • Page 1 Bailey of Bristol 2002 Series Owners Manual...
  • Page 3 OWNER’S DETAILS Model _________________________________________________ V.I.N. __________________________________________________ Owner’s Name __________________________________________ Address ________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ Tel. No. ________________________________________________ Key Nos: All Doors _____________________________________ Water Filler Cap ________________________________ Retailer’s Name _________________________________________ Address ________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ _______________________________________________________ Tel. No. ________________________________________________...
  • Page 4 THE ESSENTIAL ACCESSORY FOR YOUR NEW CARAVAN! way from the rush of every day life and the ENJOY ALL THESE busy tourist centres, you’ll find our 200 Club BENEFITS OF CLUB Sites in areas of outstanding natural beauty across the country. Some located in National Parks, MEMBERSHIP...

  • Page 5: Table Of Contents

    CONTENTS CHAPTER 1 INTRODUCTION ..............1 INTRODUCTION ....................1 WARRANTY ......................2 CARAVAN REGISTRATION AND IDENTIFICATION SCHEME ....3 SAFETY ......................... 4 CHAPTER 2 THE CARAVAN AND TOW VEHICLE ....... 6 CHAPTER 3 CARAVAN SERVICE SYSTEMS ........26 THE WATER SYSTEM ..................26 THE GAS SYSTEM ....................

  • Page 6: Table Of Contents

    CONTENTS REMI CARE DOOR FLYSCREEN ..............111 REMI CARE HALF DOOR FLYSCREEN ............. 112 REMI TOP FIXED VENTILATION ROOFLIGHT ........107 REMI JOY COMBINATION WINDOW BLINDS ........... 115 REMI FLAIR COMBINATION WINDOW BLINDS ........116 M.E.C. CARAVAN ALARM PAS 2 ............... 117 CHAPTER 5 GENERAL ................

  • Page 7: Chapter 1 Introduction

    INTRODUCTION Chapter 1 INTRODUCTION Bailey of Bristol welcome you to the ranks of Bailey Owners. This Handbook has been designed to enable you to derive the maximum benefits and enjoyment from your caravan, its information will be of benefit to both experienced and new caravanners alike.

  • Page 8: Warranty

    Bailey Caravans cannot enter into any discussions with the purchaser. Bailey retailers sell our products of their own choice and not as agents. They are, therefore, unable to bind Bailey Caravans Ltd or make any representation or undertaking whatsoever on behalf of Bailey Caravans Ltd.

  • Page 9: Caravan Registration And Identification Scheme

    INTRODUCTION Chapter 1 CARAVAN REGISTRATION AND IDENTIFICATION SCHEME (C.R.I.S) This caravan has been security marked and recorded under the Caravan Registration and Identification Scheme that is organised by the Caravan Industry. Shortly after purchasing this caravan you should receive your Touring Caravan Registration Document.

  • Page 10: Safety

    INTRODUCTION Chapter 1 SAFETY This handbook contains the information that you will require for safe enjoyment of your tourer. All of the information contained herein is important. However to draw your attention to specific items we have prefixed them as Cautions and Warnings. Cautions are Items that if ignored can result in the caravan becoming damaged.
  • Page 11 INTRODUCTION Chapter 1 vi) Never use portable cooking or heating equipment, other than electric heaters that are not direct radiant type, as it is a fire and asphyxiation hazard. vii) Your tourer is a compact living environment, and appliances should be treated in the same way as those in the home to prevent any accidental burning scalding - keep young children away from hot surfaces.
  • Page 12 CARAVAN & TOW VEHICLE Chapter 2 Introduction: Choosing the right car and caravan combination for safe and stable towing is both an art and a science. It may seem complicated to the newcomer, but a few minutes spent understanding the basic principles, common terms and definitions in use will be worthwhile in ensuring your enjoyment of our product.
  • Page 13 Caution: The towing vehicle and towing hitch handbooks/manufacturers must be consulted for their specification prior to towing. Warning: the maximum static nose weight for all Bailey caravans is 100Kg. This should never be exceeded regardless of whether the towing vehicle’s upper limit is greater.
  • Page 14 CARAVAN & TOW VEHICLE Chapter 2 Another simple method is to use bathroom scales and a suitable piece of strong timber as a platform to rest the tow hitch on. The timber can be placed vertically between the caravan tow hitch and the bathroom scales. The timber should be of such length that when the caravan tow hitch is lowered onto it, using the jockey wheel, the caravan floor is horizontal.
  • Page 15 CARAVAN & TOW VEHICLE Chapter 2 MAYBE EQUAL...
  • Page 16 CARAVAN & TOW VEHICLE Chapter 2 ii. Above 1600cc petrol or 1800cc diesel such engines should manage a caravan weighing up to 100% of the kerb weight of the towing vehicle and still give adequate performance. The towing vehicle manufacturer’s towing limit is, in some cases, less than the kerb weight.
  • Page 17 CARAVAN & TOW VEHICLE Chapter 2 Secondary braking cable (Break away device) Always ensure this is looped around a secure part of the towing bracket or towing vehicle and secured back on itself with the spring clip provided. Never loop it around the towball. Warning: it is a legal requirement to use this device on the road and it must be used.
  • Page 18 CARAVAN & TOW VEHICLE Chapter 2 LIGHT MEDIUM HEAVY ITEMS ITEMS ITEMS INCORRECT INCORRECT CORRECT...
  • Page 19 CARAVAN & TOW VEHICLE Chapter 2 3. Tyre pressures are correct according to the service handbook (remember to check the spare as well) 4. Ensue all loose articles are stowed securely Caution: do not store heavy items in roof lockers. Televisions must always be secured at floor level when towing.
  • Page 20 CARAVAN & TOW VEHICLE Chapter 2 Warning: all gas appliances and the gas bottles must be turned off whilst towing Warning: it is recommended that a minimum of 2 people work together when hitching up the caravan to the tow vehicle. To hitch the caravan to the tow vehicle Ensure that the caravan is in a suitable position, and secure with the handbrake fully on.
  • Page 21 CARAVAN & TOW VEHICLE Chapter 2 The final positioning should be carried out by maneuvering the caravan by hand. Carefully release the caravan handbrake. Manoeuvre the caravan by hand to position the caravan’s tow hitch directly over the car’s tow ball. Caution: always manoeuvre the caravan by pushing /pulling on the grab handles only.
  • Page 22 CARAVAN & TOW VEHICLE Chapter 2 Connect both the grey and black 7 pin plugs to the car’s relevant sockets ensuring there is enough loose cable for cornering, but not too much which can drag on the ground. Check all car and caravan road lights are working and the operation of the brake lights.
  • Page 23 CARAVAN & TOW VEHICLE Chapter 2 Caravan handling Allow for the caravan being slightly wider than the car. Allow additional distance from the kerb with caravan wheels so that they are not ‘bumped’. When passing other vehicles allow more than the normal clearance for driving solo.
  • Page 24 CARAVAN & TOW VEHICLE Chapter 2 space as is possible between your caravan and the high sided vehicle. Mirrors The Law requires the driver of the towing vehicle to have an adequate view to the rear. If there is no rear view through the caravan windows it may be necessary to have additional exterior towing mirrors fitted to provide a view along both sides of the caravan.
  • Page 25 CARAVAN & TOW VEHICLE Chapter 2 vii. Being overtaken by a high-sided vehicle. viii. Erratic driving. ix. Mixing radial and cross ply tyres. Nose of caravan is towing too high. Insufficient noseweight. For best stability aim at an 85% ratio of weights (see page 10). Stabilisers A stabiliser should never be used to try to improve a caravan/towing vehicle combination that has poor stability as instability may appear at...
  • Page 26 CARAVAN & TOW VEHICLE Chapter 2 Towing vehicles with the 12N &12S plugs wired to accept caravans of any make or model manufactured prior to model year 1999 may need their wiring configuration altered. If the tow car has only a single 13-pin socket, an adapter lead will be required to fit the caravan.
  • Page 27 CARAVAN & TOW VEHICLE Chapter 2 Types of tyres fitted The tyres fitted by Bailey Caravans are suitable for towing at sustained speeds of up to 81 mph (130 kph) to allow for use in countries which permit this speed.
  • Page 28 If a wheel or tyre has to be changed it should be of the same type of construction and size as originally fitted. Warning: Only use a spare wheel and tyre recommended by Bailey Caravans, which should be of the same specification as those fitted to the caravan.
  • Page 29 CARAVAN & TOW VEHICLE Chapter 2 Changing a Wheel Unhitch caravan and ensure handbrake is applied. Lower corner steadies as safety measure to stabilise the caravan. Chock the un-punctured wheel on the opposite side of the caravan to prevent any movement. iii.
  • Page 30 CARAVAN & TOW VEHICLE Chapter 2 Re-clamp it in this position. Operate the locking button on the hitch head and move the handle forward to release the mechanism. Operate the jockey wheel handle until the coupling head is clear of the towing ball. Caution: Serious damage will occur unless the locking button is depressed first and the handle lifted forward before the caravan is lifted manually.
  • Page 31 CARAVAN & TOW VEHICLE Chapter 2 Towing brackets All tow cars registered since 1 August 1998 must be fitted with a European type-approved towing bracket, by law. It is recommended that other cars not affected by this law use only towing brackets designed and tested to British Standard BS (AU) 114b, or ISO 3853.

  • Page 32: Chapter 3 Caravan Service Systems

    Chapter 3 CARAVAN SERVICE SYSTEMS THE WATER SYSTEM Water Supply All models are supplied with a 12 volt submersible pump, controlled by a pressure switch. The water inlet is located in the off-side exterior wall, protected by a lift up lid. The Submersible Pump 1.
  • Page 33 Chapter 3 CARAVAN SERVICE SYSTEMS THE WATER SYSTEM (continued) Caution: When refilling your water container always disconnect the plug from the housing and re-submerge the pump in the container before you switch the pump on again. iv. To remove the pump assembly, raise the lid to clear the plug shoulder from the lid recess, hold the pump at the plug whilst retracting it from the socket.
  • Page 34 Chapter 3 CARAVAN SERVICE SYSTEMS THE WATER SYSTEM (continued) v. Service inlet socket annually, (use Whale’s AK8834 service kit containing all serviceable parts). v. Change Aquasource Inline filter (on Pageant/Senator only) once per season positioned beneath kitchen tap. 3. Cleaning Containers and the System Cleaning instructions for both water containers and the water system are detailed in general maintenance section of the handbook.
  • Page 35 Chapter 3 CARAVAN SERVICE SYSTEMS THE WATER SYSTEM (continued) Priming the System Place pump into the container, submerging pump. ii. Place pump plug assembly into inlet socket, close lid ensuring plug assembly shoulder locates into lid recess. iii. Open all kitchen and bathroom taps to release air from system. iv.
  • Page 36 Chapter 3 CARAVAN SERVICE SYSTEMS THE WATER SYSTEM (continued) Adjusting Pressure Switch If the battery voltage is not constant, cycling may occur even at higher flow rates. This can be minimised by adjusting the switch’s diaphragm sensitivity as follows: With the system properly primed, close all taps and showers. ii.
  • Page 37 Chapter 3 CARAVAN SERVICE SYSTEMS THE WATER SYSTEM (continued) The capacity of the inboard water tank is approximately 42 litres (9.2 gallons) Always disconnect the external pump plug once filling operation is completed. Water can now be obtained from the in-board tank by switching pump switch on the control panel to INT position and opening the appropriate tap.
  • Page 38 Aquasource Direct Mains Water Connection: (This is not included as standard equipment, but is available from your nearest Bailey retailer). • The Aquasource fits simply and securely to your Whale socket system. • Comes with 7.5m of foodgrade layflat hose, which is compact for storage.
  • Page 39 Chapter 3 CARAVAN SERVICE SYSTEMS THE WATER SYSTEM (continued) thoroughly. iv. The submersible pump should be shaken out and stored in a dry place. v. Open drain plug on water heater. Caution: It is essential that the lever of ceramic ball mixer taps is fully raised and in the central position.
  • Page 40 Chapter 3 CARAVAN SERVICE SYSTEMS THE WATER SYSTEM (continued) fitted to the wastewater outlets to direct the water into a suitable container. These are both available from your caravan retailer. Caution: ensure that the exit ends of the waste water pipes, that direct the waste water into the holding container, cannot be submerged by the waste water in the holding container at any time.

  • Page 41: The Gas System

    Chapter 3 CARAVAN SERVICE SYSTEMS THE GAS SYSTEM All gas appliances fitted to your Bailey caravan are suitable for operation on both Butane and Propane without the need for adjustment. General information Gas Cylinders: Bottled Liquid Petroleum Gas (LPG) is the most convenient portable source of fuel for your caravan.
  • Page 42 Chapter 3 CARAVAN SERVICE SYSTEMS THE GAS SYSTEM (continued) All gas appliances in your tourer can have their gas supply individually isolated by turning off the relevant tap. The tap is either located on the centrally positioned gas manifold or directly beside the appliance. Regularly check flexible gas hose, joints and connections for tightness.
  • Page 43 Chapter 3 CARAVAN SERVICE SYSTEMS THE GAS SYSTEM (continued) iv. remove regulator from cylinder v. fit plastic protecting cap to cylinder With the full cylinder i. remove plastic protector from cylinder ii. connect regulator iii. place cylinder in cradle in gas locker. Avoid tension on rubber gas hose iv.
  • Page 44 Chapter 3 CARAVAN SERVICE SYSTEMS THE GAS SYSTEM (continued) electrical switches. Open all doors and windows to disperse any gas escape. Butane/Propane gas is heavier than air, any escaping gas will therefore collect at a low level. The strong unpleasant smell of gas will enable the general area of the leak to be detected.
  • Page 45 Chapter 3 CARAVAN SERVICE SYSTEMS THE GAS SYSTEM (continued) There is no danger when adequate ventilation is provided. Warning: Under no circumstances caravan’s ventilation be blocked or obstructed in any way High level ventilation is via the roof lights. The low level ventilation is via the vents in the floor at the front of the caravan living area directly behind the front bulkhead.
  • Page 46 Chapter 3 CARAVAN SERVICE SYSTEMS THE GAS SYSTEM (continued) Appliances such as cookers with naked flames should never be used for room heating. No appliance shall be used inside when being connected to the external (BBQ) socket.(Senator only)

  • Page 47: The Electrical System – 230 Volts

    Chapter 3 CARAVAN SERVICE SYSTEMS THE ELECTRICAL SYSTEM – 230 VOLT As in the home, care must be exercised when handling mains electricity. Your attention is drawn to the following notice as laid down by the Institute of Electrical Engineers. Instructions for electricity supply - low voltage (230 v) On arrival at caravan site Warning: Before connecting the caravan installation to the main supply...
  • Page 48 Chapter 3 CARAVAN SERVICE SYSTEMS THE ELECTRICAL SYSTEM – 230 VOLT (continued) ii. then disconnect the pitch lead. In case of difficulty consult an approved electrical installation contractor (who may be the local electricity board). It is dangerous to attempt modifications and additions yourself.
  • Page 49 Chapter 3 CARAVAN SERVICE SYSTEMS THE ELECTRICAL SYSTEM – 230 VOLT (continued) It is always advisable to have at least one other mains appliance switched on with the charger unit to minimise the chance of damage to it. Caution: Do not connect the 12 volt output of the generator to the battery terminals.
  • Page 50 Chapter 3 CARAVAN SERVICE SYSTEMS THE ELECTRICAL SYSTEM – 230 VOLT (continued) The unit gives overload and earth leakage protection for the 230v electrical supply in your caravan. For normal operation all switches on the unit need to be in the ON position. The switches on the left of the unit are known as M.C.B.’s (miniature circuit breakers).
  • Page 51 Chapter 3 CARAVAN SERVICE SYSTEMS THE ELECTRICAL SYSTEM – 230 VOLT (continued) Warning: Always disconnect the electrical connector between the towing vehicle and the caravan before connecting a 230v supply to the caravan and before charging the caravan battery by any other means. It is possible that all of the 230v mains electrical equipment may not be able to be operated simultaneously.
  • Page 52 Chapter 3 CARAVAN SERVICE SYSTEMS...

  • Page 53: The Electrical System – 12 Volts

    Chapter 3 CARAVAN SERVICE SYSTEMS THE ELECTRICAL SYSTEM – 12 VOLT These units provide, via 230 volt AC, a 12 volt DC supply to the 12 volt equipment and charging of the caravan battery. Maximum is 10 amps and incorporates full automatic charging regulation. This means only the current the battery needs will be supplied, overcharging will not occur.
  • Page 54 Chapter 3 CARAVAN SERVICE SYSTEMS THE ELECTRICAL SYSTEM – 12 VOLT (continued) The BCA 1212 Unit The system is fitted with an automatic relay to select the power source. When the car is connected via the ‘s’ plug the car power will be used. When the car is not connected the battery and or the power supply will be used to power the caravan.
  • Page 55 Chapter 3 CARAVAN SERVICE SYSTEMS THE ELECTRICAL SYSTEM – 12 VOLT (continued) ii) Water pumping light, is only activated when the pump is running iii) Water pump isolation switch. Selects either interior (up position) Senator only or exterior (down position). Off is central The 12-volt electrical system fuses are located in the caravan bed box.
  • Page 56 Chapter 3 CARAVAN SERVICE SYSTEMS Auxiliary Battery storage/mains inlet The battery and 230V mains inlet are located in a special locker mounted in the side of the caravan. The door frame has a cable recess allowing the door to be locked when the mains cable is connected. This locker will accommodate a battery up to 90 amperes/hours capacity.
  • Page 57 Chapter 3 CARAVAN SERVICE SYSTEMS CONTROL PANEL SPB2...

  • Page 58: Chapter 4 Caravan Equipment

    CARAVAN EQUIPMENT Chapter 4 THE TRUMA ULTRASTORE WATER HEATER Operating Instructions Filling the Truma Ultrastore with water Check that the safety/drain valve in the cold water intake is closed. Lever should be in the horizontal position, position (e). ii. Open the hot tap in bathroom or kitchen with pre-selecting mixing taps or single lever fittings set to hot.

  • Page 59: Caravan Equipment

    CARAVAN EQUIPMENT Chapter 4 THE TRUMA ULTRASTORE WATER HEATER (continued) Switching off (gas operation) Switch off the water heater at the side switch (a). Mount Cowl cover. Drain the water if there is a risk of frost. Close quick-acting valve in the gas supply line if the appliance is not to be used for an extended period of time and close the gas cylinder.
  • Page 60 CARAVAN EQUIPMENT Chapter 4 THE TRUMA ULTRASTORE WATER HEATER (continued) Draining the water heater e = Lever position “Closed” f = Lever position “Drain” Disconnect power for water pump (main switch or pump switch). ii. Open hot water taps in bathroom and kitchen. iii.
  • Page 61 CARAVAN EQUIPMENT Chapter 4 THE TRUMA ULTRASTORE WATER HEATER (continued) The water tank in the Truma-Ultrastore is of high quality food-grade stainless steel. The special equipment available below, water hose connections and the safety/drain valve fulfil the EC guideline for quality in plastic parts (90/396/EEC).
  • Page 62 CARAVAN EQUIPMENT Chapter 4 THE TRUMA ULTRASTORE WATER HEATER (continued) General Safety Notes: In the event of leaks in the gas systems or if there is a smell of gas: Extinguish all naked flames Do not smoke Switch off the appliance and the gas cylinder Open the windows Do not operate any electrical switches Have the entire system checked by an expert...
  • Page 63 CARAVAN EQUIPMENT Chapter 4 THE TRUMA ULTRASTORE WATER HEATER (continued) vi. If the burner makes an unusual noise or if the flame lifts off, it is likely that the regulator is faulty and it is essential to have it checked. Technical Data Water contents: 10 litres...
  • Page 64 CARAVAN EQUIPMENT Chapter 4 THE TRUMA S 3002 EL SPACE HEATER Gas Operation a = Control knob b = Integrated control panel for Trumavent fan TEB c = Piezo ignitor d = Flame observation window e = Name plate (remove casing) f = Thermostat probe In case of left-handed installation, the parts are arranged on the other side.
  • Page 65 CARAVAN EQUIPMENT Chapter 4 THE TRUMA S 3002 EL SPACE HEATER (continued) Always wait at least 2 minutes before attempting to re-ignite, otherwise there is a risk of blowbacks (misfiring)! This also applies if a working heater goes out and has to be re-lit. v.
  • Page 66 CARAVAN EQUIPMENT Chapter 4 THE TRUMA S 3002 EL SPACE HEATER (continued) iii. Any alteration to the appliance (including exhaust duct and cowl) or the use of spare parts and accessories which are important to the function of the heater and which are not original Truma parts, as well as the non-observance of the installation and operating instructions, will lead to the cancelling of the guarantee and exclusion of liability claims.
  • Page 67 CARAVAN EQUIPMENT Chapter 4 THE TRUMA S 3002 EL SPACE HEATER (continued) from overheating. Do not place flammable objects near the heater. Please follow these guidelines in the interest of your own safety. ix. If the burner makes an unusual noise or if the flame lifts off while burning, it is likely that the regulator is faulty, and it is essential to have it checked.
  • Page 68 CARAVAN EQUIPMENT Chapter 4 THE TRUMA S 3002 EL SPACE HEATER (continued) iv. Always connect the pressure regulator to the gas cylinder with great care. Inspect the regulator connection hoses regularly for signs of weakness. Caravanning gas cylinders must always be upright. Technical data Type of Gas : Liquid gas (propane/butane)
  • Page 69 CARAVAN EQUIPMENT Chapter 4 THE TRUMA S 3002 EL SPACE HEATER (continued) Switching on Caution: before switching on, ensure that the fuse protection for the power supply of the camp site is sufficient for the selected power setting (b) – see technical data. Warning: the pitch lead for the caravan must be fully unwound prior to use.
  • Page 70 CARAVAN EQUIPMENT Chapter 4 THE TRUMA S 3002 EL SPACE HEATER (continued) 5. Any alteration to the appliance (including exhaust duct and cowl) or the use of spare parts and accessories which are important to the function of the heater and which are not original Truma parts, as well as the non-observance of the installation and operating instructions, will lead to the cancelling of the guarantee and exclusion of liability claims.
  • Page 71 CARAVAN EQUIPMENT Chapter 4 a = Manual control (e.g. for ventilation) Adjust desired output at the control knob. b = Off (or automatic operation/heating with heaters Trumatic S 3002 K and S 5002 K) c = Automatic operation (heating) The output steadily adjusts to the respective heat emission of the heater. The maximum output can be limited at the control knob, as required.
  • Page 72 CARAVAN EQUIPMENT Chapter 4 THE TRUMA S 3002 EL SPACE HEATER (continued) Warm air distribution The warm air system is designed individually for each type of vehicle on a modular basis. There is an extensive expansion programme available with accessories for retrofitting (see brochure). You can obtain diagrams free of charge from the Truma Service Centre, showing optimal installation suggestions for warm air systems in all current-type caravans and mobile homes.
  • Page 73 CARAVAN EQUIPMENT Chapter 4 THE TRUMA S 3002 EL SPACE HEATER (continued) Note: If the air output drops or the operating noise increases, the fan impeller wheel may be severely soiled. Cleaning (with switched off appliance!). Caution: We recommend removing dust which has collected on the heat exchanger and base plate of the heater and on the impeller wheel of the Trumavent fan, once every 12 months.

  • Page 74: Truma Triomatic Automatic Gas Change-Over System

    CARAVAN EQUIPMENT Chapter 4 TRUMA TRIOMATIC AUTOMATIC GAS CHANGE-OVER SYSTEM Operating instructions Warning: Always ensure that the gas cylinders are in an upright position and secured against tipping over. The operating and reserve cylinder regulators (6+7) have combination fittings for the cylinders. Always assemble the regulators (6+7) in such a way that the blue safety caps are facing upwards.
  • Page 75 CARAVAN EQUIPMENT Chapter 4 AUTOMATIC GAS CHANGE-OVER SYSTEM (continued) regardless as to whether the gas is supplied from the operating cylinder or the reserve cylinder. The two medium pressure regulators are the operating cylinder regulator (green type plate) and the reserve cylinder regulator (red type plate). The gas cylinder that is supplying the caravan at a given time is indicated by the gauge (8).
  • Page 76 CARAVAN EQUIPMENT Chapter 4 AUTOMATIC GAS CHANGE-OVER SYSTEM (continued) 4. If the pressure gauge indicates the same pressure after a period of 10 minutes there are no leaks. If the pressure drops the gas system is leaking. The gas system should then be inspected and repaired by a competent person.

  • Page 77: Country Leisure Cooking Appliances

    CARAVAN EQUIPMENT Chapter 4 THE COUNTRY LEISURE COOKING APPLIANCES Operating Instructions Ensure the gas cylinder is turned on. In the event of a gas smell turn off at the cylinder and contact supplier. THE ARGENT HOB Hotplate Burners Warning: Glass lids may shatter when heated. Turn off all burners and grill before shutting the lid.
  • Page 78 CARAVAN EQUIPMENT Chapter 4 COOKING APPLIANCES (continued) For simmering, turn the knob further anti-clockwise to the low rate position. To turn the burner off, rotate knob fully clockwise until the line on the knob lines up with the dot on the control panel. The burners on this appliance have fixed aeration and no adjustment is required.
  • Page 79 CARAVAN EQUIPMENT Chapter 4 COOKING APPLIANCES (continued) Oven 1. Ensure the gas cylinder is connected and turned on. In the event of a gas smell turn off at gas cylinder and contact supplier. 2. Remove all accessories and packing that may be in the oven and clean the interior before using it for the first time.
  • Page 80 CARAVAN EQUIPMENT Chapter 4 COOKING APPLIANCES (continued) 8. Oven shelves : the oven shelves have been designed to allow good circulation at the rear of the oven and are also fitted with a raised bar to prevent trays or dishes making contact with the back of the oven. To remove a shelf, pull forward until it stops, raise at front and remove.
  • Page 81 CARAVAN EQUIPMENT Chapter 4 COOKING APPLIANCES (continued) DISH GAS MARK SHELF POSITION COOKING TIME scones 8-15 mins small cakes 15-25 mins victoria sandwich 20-30 mins puff 15-30 mins flaky 15-30 mins shortcrust 15-55 mins shortbread fingers 25-30 mins rice pudding 100-120 mins baked custard 50-60 mins...
  • Page 82 CARAVAN EQUIPMENT Chapter 4 COOKING APPLIANCES (continued) Do Not allow children near the cooker when in use. Turn pan handles away from the front so that they cannot be caught accidentally Do Not allow fats or oils to build up in the oven trays or base Do Not use abrasive cleaners or powders that will scratch the surfaces of the hotplate and oven.

  • Page 83: Fire Sentry Smoke Alarm

    CARAVAN EQUIPMENT Chapter 4 THE FIRE SENTRY SMOKE ALARM The Smoke Alarm is operational once the battery is connected. When products of combustion are sensed, the unit sounds a loud pulsating alarm until the air is cleared. False Alarms ‘Hush’ Control Units with the ‘hush’...
  • Page 84 CARAVAN EQUIPMENT Chapter 4 ELECTROLUX REFRIGERATOR When using your refrigerator for the first time, it is advisable to wash the interior and its accessories. When the caravan is on tow, the refrigerator should be operated electrically, i.e. from the 12v battery in the towing vehicle and not by means of bottled gas.

  • Page 85: Refrigerator Models

    CARAVAN EQUIPMENT Chapter 4 ELECTROLUX REFRIGERATOR MODEL RM 4270 (continued) this, the toggle switch (F) should be ‘ON’ during gas operation. An indicator lamp in the switch flashes when the automatic igniter attempts to light the burner. Otherwise this lamp is off. LP Gas Operation –...
  • Page 86 CARAVAN EQUIPMENT Chapter 4 ELECTROLUX REFRIGERATOR MODEL RM 4270 (continued) 12v Operation Only operate your refrigerator on 12v when the engine of your vehicle is running otherwise your battery will soon become discharged. Before operating the refrigerator on 12v it should be pre-cooled together with its contents by running it on bottled gas or mains for a few hours before starting a journey.
  • Page 87 CARAVAN EQUIPMENT Chapter 4 ELECTROLUX REFRIGERATOR MODEL RM 6291L & 6271 RM 6291L A = energy selector switch B = gas/electric thermostat D = “automatic ignition” indicator Automatic ignition 1. Set energy selector switch (A) to Gas. 2. Press and hold rotary switch. 3.
  • Page 88 CARAVAN EQUIPMENT Chapter 4 MODEL RM 6291L & 6271 (continued) with automatic flame protection, which automatically cuts off the supply of gas approximately 30 seconds after the flame goes out. When using for the first time, and after changing the gas cylinder, the gas pipes may contain air.
  • Page 89 CARAVAN EQUIPMENT Chapter 4 MODEL RM 6291L & 6271 (continued) gas. The desired power option is selected by means of energy selector switch (A). Energy selector switch (A) has four settings: AC mains power, DC (12V), gas (liquid gas), O (off). Electrical operation 1.
  • Page 90 CARAVAN EQUIPMENT Chapter 4 MODEL RM 6291L & 6271 (continued) Manual ignition 1. Set energy selector switch (A) to gas 2. Press and hold rotary switch. A = energy selector switch B = gas/electric thermostat C = “Piezo ignition” 3. Activate Piezo ignition (C) several times at intervals 1-2 seconds. 4.
  • Page 91 CARAVAN EQUIPMENT Chapter 4 MODEL RM 6291L & 6271 (continued) Useful Hints Make sure that : The refrigerator is not operating in 12v when the vehicle is parked, otherwise you may drain the car battery. ii. Defrosting is carried out periodically. iii.
  • Page 92 CARAVAN EQUIPMENT Chapter 4 MODEL RM 6291L & 6271 (continued) periodically but make sure that the refrigerator is switched off when doing this. Travel Catch All models are fitted with a travel catch to keep the refrigerator door securely closed when the vehicle is on the move. Remember always to push the catch down so that its lower end fully engages the plastic bush in the top of the door, before moving off.
  • Page 93 CARAVAN EQUIPMENT Chapter 4 THE THETFORD CASSETTE PORTA POTTI C2 Preparing for use Open access door on the side of the Caravan and swing out fresh water fill funnel. ii. Fill freshwater tank using a hose or jerry can until water funnel level reaches neck (Senator Only: A power supply is provided adjacent to the Porta Potti access door for use with an external pump).
  • Page 94 CARAVAN EQUIPMENT Chapter 4 THE THETFORD CASSETTE PORTA POTTI C2 (continued) vii. Slide the Cassette, pour out spout facing outside into the Caravan through access door. Never force insertion or removal of the Cassette tank, damage to system can occur. viii.
  • Page 95 CARAVAN EQUIPMENT Chapter 4 THE THETFORD CASSETTE PORTA POTTI C2 (continued)
  • Page 96 CARAVAN EQUIPMENT Chapter 4 THE THETFORD CASSETTE PORTA POTTI C2 (continued) xiii. Remove spout cap. Grasp unit by upper carrying handle nearest to pour out spout. Place other hand on upper rear hand grip so that the air relief valve button can be depressed with thumb while emptying, to ensure smooth outflow of tank contents.
  • Page 97 CARAVAN EQUIPMENT Chapter 4 THE THETFORD CASSETTE C-200 CW / CWE The unit consists of two sections, a permanently installed toilet system and a slide out waste holding tank. The toilet section of the C-200 CW includes a rotatable bowl, removable seat and cover, a console with flush handle, a built in flush water tank and a waste level warning indicator.
  • Page 98 CARAVAN EQUIPMENT Chapter 4 THE THETFORD CASSETTE C-200 CW / CWE (continued) v. Slide holding tank into position through access door (fig.5). Never force insertion as this can cause severe damage to the toilet. vi. Make sure the holding tank is secured by the retaining clip (fig.6). vii.
  • Page 99 CARAVAN EQUIPMENT Chapter 4 THE THETFORD CASSETTE C-200 CW / CWE (continued)
  • Page 100 CARAVAN EQUIPMENT Chapter 4 THE THETFORD CASSETTE C-200 CW (continued) authorised disposal point. Place the holding tank in the vertical position and rotate the pour-out spout upwards (fig.13). xiv. Remove the measuring cap. Grasp the unit by upper carrying handle nearest pour-out spout.
  • Page 101 CARAVAN EQUIPMENT Chapter 4 THE THETFORD CASSETTE C-200 CW / CWE (continued) pour-out spout and leave the blade open so the cassette can dry. Caution: Never use washing-up liquids which contain chlorine, solvents or other aggressive substances to clean the toilet. Winterising / Storage The Thetford Cassette is easily winterised for storage.

  • Page 102: Omnivent Rooflight Mounted Extractor Fan

    CARAVAN EQUIPMENT Chapter 4 OMNIVENT ROOFLIGHT MOUNTED EXTRACTOR FAN Use Ventilator (only for OMNIVENT 12V) The ventilator is started by the red switch; or “blowing” or “suction”. The airflow is adjusted by the black switch: position 1 = 7m /min. (245 cft/min.) (15W - 1.2 A) position 2 = 12m /min.

  • Page 103: Al-Ko Caravan Chassis

    CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS Chassis members The ALKO lightweight chassis has been perfected by many years of research and development, supported by an exhaustive test programme. Manufactured from high quality steel, the chassis has extra deep sections to provide strength at points of maximum stress.
  • Page 104 CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS (continued) The galvanised chassis should not be painted or subjected to any other protective treatment. Should the galvanising become superficially damaged exposing the steel core, this should be cleaned and treated with a cold galvanising spray obtainable from vehicle accessory outlets.
  • Page 105 160) must be engaged first and the handle lifted forward. Brake drum/hub assembly The Euro Axle fitted to your Bailey caravan comes complete with maintenance-free wheel bearings greased and serviced for life. Adjustment is not required during the design life of the sealed bearing (100,000 km).
  • Page 106 CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS (continued) Couplings Clean and grease spherical seat, bearing parts and pivot pins regularly. ii. Thoroughly examine all moving parts for wear and correct functioning. iii. AKS Stabiliser heads must NEVER be greased. AKS 2000 coupling Caution: When using a caravan fitted with an AKS 2000 hitch the tow ball must be free of grease and any foreign matter prior to coupling with the caravan...
  • Page 107 CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS (continued) Then pull the coupling handle up and push it forward in the direction of the arrow. The hitch can then be lowered onto the vehicle tow ball by unwinding the jockey wheel. Put the opened coupling on the tow-ball of the towing vehicle and undo the coupling handle (2).
  • Page 108 CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS (continued) on its own. However, press down with your hand as well. Closure and fastenings are automatic. Warning: the ball coupling is fully coupled (correctly connected) when the green band of the safety button is visible. Press the stabilising handle (1) down until it is over centre and against the end stop.
  • Page 109 CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS (continued) Caution: during opening and closing, the AKS 2000 must be operated one person only. Caution: never close the stabilising handle with a lever or your foot. Do not pull on the Stabilising handle to manoeuvre the caravan. Warning: When opening or closing the stabilising handle do not leave your hand on the coupling handle.
  • Page 110 CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS (continued) How to Check the Efficiency of the AKS 2000: (i) Couple the AKS 2000 on (ii) Pull stabilizing handle in off position 1 (iii) Close stabilising handle till resistance is felt (friction linings are in contact with the tow ball - but not under pressure).
  • Page 111 CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS (continued) Storing To reduce the possibility of contamination of component parts of the AKS 2000 the stabilising handle should be closed. Towing ball The automobile towing ball should measure 50mm maximum and 49mm minimum diameter (DIN 74058).
  • Page 112 CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS (continued) Braking system adjustment (At 500 miles, then every 3,000 miles or 1 year) Ensure the towing shaft with coupling heads is pulled fully forward (fig. 1). ii. Release the handbrake to the fully off position. If the handbrake will not go down the whole way because of the fairing or any other obstruction;...
  • Page 113 CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS (continued) direction of the arrow embossed on the backplate until there is resistance in the wheel rotation (fig. 2). vi. Slacken off the starwheel adjuster until the road wheel turns freely in the forward direction (fig.
  • Page 114 CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS (continued) Fig. 3 never bent or curved under any fittings. On tandem axles, using the double balance bar, a brake rod support tube (Part No. 228827) must always be fitted on the end of the brake rod, passing through the centre aperture on the abutment.
  • Page 115 CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS (continued) xiii. Adjust the two locking nuts, forward of the spring cylinder (fig. 3), (on some chassis a single Nyloc nut is used) to give 1mm of clearance on the spring cylinder. This cylinder (the energy store for the handbrake operation) must be able to rotate only, not slide on the brake rod.
  • Page 116 CARAVAN EQUIPMENT Chapter 4 THE ALKO CARAVAN CHASSIS (continued) Warning: The torque settings should be rechecked after 50 miles. Wheel bolts should never be lubricated.

  • Page 117: Remi Care Door Flyscreen

    CARAVAN EQUIPMENT Chapter 4 REMI CARE DOOR FLYSCREEN Operating Instructions To close REMIcare: Pull handle/crossbar across door aperture until hook engages on closing profile. ii. To open REMIcare: a) From inside. To release hook, pull handle/crossbar slightly toward you then, still holding the handle/crossbar, allow the tension to pull the flyscreen back into the cassette.
  • Page 118 CARAVAN EQUIPMENT Chapter 4 REMIpart DOOR FLYSCREEN Operating Instructions The screen is designed to be used when the upper half of the stable door is open. Using the lower bar finger grip gently pull the screen downwards and around the curve towards the closed section of the door. Push firmly and the bar will clip onto and guide the screen back to the top position.

  • Page 119: Remi Top Fixed Ventilation Rooflight

    CARAVAN EQUIPMENT Chapter 4 REMI TOP FIXED VENTILATION ROOFLIGHT Operating Instructions Caution: Before towing please open the blinds and ensure the REMItop is completely closed and both handles/locks are engaged. To open RemiTop: a) Unlock by pressing buttons in centre of both handles/locks and turning both through 90 degrees.
  • Page 120 CARAVAN EQUIPMENT Chapter 4 REMI TOP FIXED VENTILATION ROOFLIGHT (continued) v. Cleaning: Use a damp cloth, and if necessary, a normal household cleaner without abrasives or solvents. Caution: DO NOT spray water under the cover. There is an air gap between the frame and the cover (for fixed air ventilation) through which water deliberately sprayed under the cover would enter the interior.

  • Page 121: Remi Joy Combination Window Blinds

    CARAVAN EQUIPMENT Chapter 4 REMIjoy combination window blinds (Senator Only) Operating Instructions The sun screen may be adjusted to any level by pulling gently upwards using the finger grip in the centre of the lower bar. This will also have the effect of giving visual privacy.

  • Page 122: Remi Flair Combination Window Blinds

    CARAVAN EQUIPMENT Chapter 4 REMIflair Combination Window Blinds. Operation and Care The cassette contains a sun screen and a fly screen blind. The fly screen is operated by gently pulling down the handle nearest the window. It is designed to be either fully up or fully down. Push the handle towards the window until the crossbar hooks into the catch.

  • Page 123: M.e.c. Caravan Alarm Pas 2

    CARAVAN EQUIPMENT Chapter 4 M. E. C. CARAVAN ALARM PAS 2 Operating the alarm The PAS 2 is simple to arm and disarm using the same procedures for both operations. The functions of the alarm can be operated by entering the correct code into the keypad, which should be done, in the following sequence.
  • Page 124 CARAVAN EQUIPMENT Chapter 4 M. E. C. CARAVAN ALARM PAS 2 (continued) To DISARM the alarm, follow this sequence. Press * To activate the control panel, the red LED will now be illuminated to indicate the key pad is active, and the green LED will be illuminated to show that the alarm is set.
  • Page 125 CARAVAN EQUIPMENT Chapter 4 M. E. C. CARAVAN ALARM PAS 2 (continued) The keypad will now be set at new code (example 5678) Factory set entry time: 18 seconds. exit time: 18 seconds.

  • Page 126: Chapter 5 General

    Warning: The use of high pressure water jets to clean your caravan will invalidate your warranty. Acrylic Windows The windows fitted to your Bailey caravan are manufactured from high quality acrylic using the latest plastic processing methods. For cleaning, use only generous amounts of water to wash away dust and road grit etc.
  • Page 127 GENERAL Chapter 5 GENERAL MAINTENANCE (continued) Window Catches and Stays Turn catch arm to the vertical position to open. A night vent position is available by locking the catch into the outer catchplate slot. The windows are held open by an adjuster knob, tightening off the knob in a clockwise direction will hold the window open in the desired position.
  • Page 128 GENERAL Chapter 5 GENERAL MAINTENANCE (continued) ii. Sponge the affected area with warm soapy water taking care not to soak the material. iii. Leave to dry in normal conditions. These actions will not affect the FR treatment of the fabric. Heavy soiling will require professional cleaning.
  • Page 129 GENERAL Chapter 5 GENERAL MAINTENANCE (continued) Cleaning should be carried out immediately after use using warm soapy water and a soft cloth. Stubborn stains may be removed using diluted lemon juice. Thetford bathroom cleaner is suitable for cleaning the shower and vanity unit plastic items (sinks, shower trays, thetford toilets etc).
  • Page 130 GENERAL Chapter 5 GENERAL MAINTENANCE (continued) 4. The container should then be totally filled with water containing an appropriate disinfectant/sterilant solution and allowed to stand for the recommended contact time (e.g. Milton for 15 minutes). 5. The solution should be emptied from the container. 6.
  • Page 131 GENERAL Chapter 5 GENERAL MAINTENANCE (continued) Suitable sterilising chemicals are available from your caravan dealer, accessory shop, chemists or home-brew shops. It is not, however, recommended to use bleach or sodium metabisulphite. This guidance has been prepared with the kind co-operation and assistance of The Environmental Health Department of The Borough Council of King’s Lynn and West Norfolk.

  • Page 132: Fire And Safety Precautions

    GENERAL Chapter 5 FIRE AND SAFETY PRECAUTIONS Warning: Your attention is drawn to the notice affixed in the caravan advising on fire prevention, ventilation and what to do in case of fire. Ensure that the occupants are familiar with escape routes, in case of a fire.
  • Page 133 GENERAL Chapter 5 FIRE AND SAFETY PRECAUTIONS (Continued) Ventilation All ventilation complies with EN 721 and vents should not be obstructed in any manner as this could lead to insufficient fresh air. In this case the confined atmosphere becomes depleted of oxygen which leads to the formation of the highly poisonous gas ‘carbon monoxide’.
  • Page 134 GENERAL Chapter 5 FIRE AND SAFETY PRECAUTIONS (Continued) Portable Appliances Warning: Never use portable cooking or heating equipment, other than electric heaters that are not of the direct radiant type, as it is a fire and asphyxiation hazard. Modifications Warning: Never allow modification of electrical or LPG systems and appliances except by qualified persons.
  • Page 135 GENERAL Chapter 5 ASSEMBLING THE BUNKS...
  • Page 136 GENERAL Chapter 5 ASSEMBLING THE BUNKS (continued) Lift up Bunk Remove cushions and draw the curtains. ii/iii. Holding bunk in both hands pull it inwards whilst lifting upwards. iv. The bunk mechanism will automatically lock in the up position. v. Release retaining straps on the underside of bunk base. The second half of the bunk base can now be hinged open.
  • Page 137 GENERAL Chapter 5 ASSEMBLING THE BUNKS (continued) Slatted Bed (Fig. 1) Grasp front rail. ii. Walk backward holding rail until bed is fully extended. iii. Arrange seat cushions to suit. Side Dinette Bed (Fig. 2) Remove table from support leg. Fig.

  • Page 138: Fault Finding

    GENERAL Chapter 5 WATER SYSTEM - FAULT FINDING FAULT - Water not flowing from any tap when operated but pump runs Cause Cure Freshwater tank empty Check Pump wired in reverse Check wiring, refer to pump manufacturers’ instructions Pump not primed Refer to pump manufacturers’...
  • Page 139 GENERAL Chapter 5 WATER SYSTEM - FAULT FINDING (continued) FAULT - Water flows from hot tap but has reduced flow from cold Cause Cure Cold water pipe kinked preventing flow Check and re-route if necessary Blockage in cold pipe line Disconnect pipes after 1st Y connector and check up to tap Cold tap not connected...
  • Page 140 GENERAL Chapter 5 WATER SYSTEM - FAULT FINDING (continued) FAULT - Warm water flow out of cold tap Cause Cure Hot water back feeding into cold line, Fit non-return valve in cold supply near tap usually if mixer tap or single outlet hot and cold taps are being used FAULT - Water Heater pressure relief valve venting water Cause...
  • Page 141 GENERAL Chapter 5 ROOM HEATER - FAULT FINDING FAULT - Heater will not light Symptoms Cause Cure Spark visible No gas. Bottle temperature too low Check bottle and taps. See gas supply notes. Regulator malfunction. See gas supply notes. Overgassed. Refer to lighting instructions.
  • Page 142 GENERAL Chapter 5 BRAKE FAULT FINDING CHART — AL-KO FAULT - Braking is one-sided Cause Cure Incorrect adjustment at wheel. Adjust as described. Brake cable seized. Free off cable or replace. Brake lining contaminated with grease. Replace brake shoe assemblies. FAULT - The trailer brakes during mild decelerations Cause Cure...
  • Page 143 GENERAL Chapter 5 BRAKE FAULT FINDING CHART — AL-KO (continued) FAULT - Trailer brakes inoperative Cause Cure Brakes underadjusted. Check action and rectify. Lining contamination. Replace brake shoe assemblies. Seized cables. Free off or replace. Linings worn out. Replace brake shoe assemblies. FAULT - Hot brakes Cause Cure...

  • Page 144: Chapter 6 Technical Information

    Chapter 6 TECHNICAL INFORMATION...
  • Page 145 Chapter 6 TECHNICAL INFORMATION...
  • Page 146 Chapter 6 TECHNICAL INFORMATION...
  • Page 147 Chapter 6 TECHNICAL INFORMATION...
  • Page 148 Chapter 6 TECHNICAL INFORMATION DIMENSIONS & SPECIFICATIONS MODEL BERTHS INTERNAL SHIPPING OVERALL OVERALL MAXIMUM TYRE TYRE BODY LENGTH BODY HEIGHT HEADROOM SIZES PRESSURE LENGTH WIDTH (P.S.I/BAR) RANGER 380/2 3.759m 5.249m 2.19m 2.71m* 1.90m 185 R14 LI90 35/2.46 RANGER 460/2 4.547m 6.037m 2.19m 2.71m*...
  • Page 149 Chapter 6 TECHNICAL INFORMATION DIMENSIONS & SPECIFICATIONS (continued) MODEL AWNING MAXIMUM M.R.O. MASS OF PAYLOAD PAYLOAD TOTAL SIZE TECHNICAL ESSENTIAL ALLOWANCE ALLOWANCE USER PERMISSIBLE HABITATION PAYLOAD LADEN MASS EQUIPMENT PERSONAL OPTIONAL EFFECTS EQUIPMENT EQUIPMENT RANGER 380/2 794cm 1027kg 830kg 81kg 94kg 22kg 197kg...
  • Page 150 Chapter 6 TECHNICAL INFORMATION DIMENSIONS & SPECIFICATIONS (continued) MODEL BERTHS INTERNAL SHIPPING OVERALL OVERALL MAXIMUM TYRE TYRE BODY LENGTH BODY HEIGHT HEADROOM SIZES PRESSURE LENGTH WIDTH (P.S.I/BAR) SENATOR VERMONT 4.842m 6.488m 2.19m 2.71m* 1.90m 195 R14 LI96 37/2.61 SENATOR ARIZONA 5.508m 7.080m 2.19m...
  • Page 151 Chapter 6 TECHNICAL INFORMATION DIMENSIONS & SPECIFICATIONS (continued) MODEL AWNING MAXIMUM M.R.O. MASS OF PAYLOAD PAYLOAD TOTAL SIZE TECHNICAL ESSENTIAL ALLOWANCE ALLOWANCE USER PERMISSIBLE HABITATION PAYLOAD LADEN MASS EQUIPMENT PERSONAL OPTIONAL EFFECTS EQUIPMENT EQUIPMENT SENATOR VERMONT 907cm 1293kg 1086kg 102kg 105kg 207kg SENATOR ARIZONA...

  • Page 152: Awning Sizes

    Chapter 6 TECHNICAL INFORMATION AWNING SIZES The following are the ground to ground dimensions through the awning channel. These dimensions are issued as a guideline only, please refer to your dealer for the correct awning size to suit your particular caravan. RANGER 380/2 794 cms...
  • Page 153 Chapter 6 TECHNICAL INFORMATION BULB, TUBE & FUSE SPECIFICATION ROAD LIGHTS (All Models) Front Marker light 12 volt 5 watt Push in (QH) Side Marker light 12 volt 5 watt Brake lights 12 volt 21 watt Road lights 12 volt 10 watt Fog lights 12 volt 21 watt Indicator lights...
  • Page 154 Chapter 6 TECHNICAL INFORMATION FUSES Caravan Battery - 10 amp blade (red) Caravan Battery + 15 amp blade (red) Charger + 15 amp blade (blue) Permanent live supply from car + 10 amp blade (red) Permanent live supply from car - 10 amp blade (red) Fridge 15 amp blade (blue)
  • Page 155 ANNUAL SERVICE To qualify for the factory backed warranty your caravan must be serviced /moisture tested by an approved Bailey Service Centre every 12 months (or within 6 weeks of each anniversary of purchase) in accordance with the NCC recommended service schedule and the following moisture test.
  • Page 156 Readings greater than 20% will identify areas needing further investigation and possibly remedial work. THERMAL INSULATION HEATING GRADE All Bailey caravans are manufactured and approved by the National Caravan Council to EN1645–1 thermal insulation and heating classification grade 2. Grade 2 is classified as being able to achieve an average temperature difference of 20°C between inside and outside the caravan when the...
  • Page 157 Chapter 6 TECHNICAL INFORMATION...
  • Page 158 Chapter 6 TECHNICAL INFORMATION 3000 MILES OR 12 MONTHS 6000 MILES OR 2 YEARS AFTER DELIVERY AFTER DELIVERY STANDARD DAMP CHECK STANDARD DAMP CHECK DEALER STAMP DEALER STAMP DATE DATE VIN No. VIN No. 9000 MILES OR 3 YEARS 12000 MILES OR 4 YEARS AFTER DELIVERY AFTER DELIVERY STANDARD DAMP CHECK...
  • Page 159 Chapter 6 TECHNICAL INFORMATION 15000 MILES OR 5 YEARS 18000 MILES OR 6 YEARS AFTER DELIVERY AFTER DELIVERY STANDARD DAMP CHECK STANDARD DAMP CHECK DEALER STAMP DEALER STAMP DATE DATE VIN No. VIN No. 21000 MILES OR 7 YEARS 24000 MILES OR 8 YEARS AFTER DELIVERY AFTER DELIVERY STANDARD DAMP CHECK...
  • Page 160 Chapter 6 TECHNICAL INFORMATION NOTES...
  • Page 161 Chapter 6 TECHNICAL INFORMATION NOTES...
  • Page 162 Chapter 6 TECHNICAL INFORMATION NOTES Designed and Produced by Preset Graphics Rayburn House, 1 Parcel Terrace, Derby DE1 1LY Tel: 01332 205136. Fax: 01332 206356...
  • Page 164 Bailey of Bristol South Liberty Lane, Bristol BS3 2SS, England www.bailey-caravans.co.uk...

This manual is also suitable for:

2002 ranger 380/22002 ranger 460/22002 ranger 470/42002 ranger 500/52002 ranger 510/42002 ranger 520/4 ... Show all

Table of Contents

Save PDF