Honeywell ADEMCO 5828 Installation And Setup Manual

GENERAL INFORMATION
The 5828 and 5828V are wireless, bidirectional, fixed-word,
nonaddressable keypads that are used in conjunction with
LYNX Series control panels or VISTA Series control panels
that are using a 6160RF Keypad transceiver.
Both keypads provide:
•
Four programmable special function keys
•
Wall-mount plate allowing easy removal of the keypad
and battery replacement
•
Optional Desktop mount /AC adapter kit,
(ADEMCO P/N 5828DM)
•
Battery powered with 3-AA batteries
In addition to the above features, the 5828V keypad provides
the following:
•
Memo/Message center
•
Voice Response – system status, zone information, and
alarms with zone information
•
Stored Message LED indication
•
Built-in microphone and speaker
NOTES:
•
The 5828/5828V cannot be used as a primary keypad to
program and/or test any security system. All systems
require a hard-wired keypad to do so. Once programmed
and tested, the 5828/5828V can be used to initiate all
other keypad functions in both the VISTA and LYNX
series systems. However, you must have at least one
hard-wired keypad permanently connected on VISTA
series control panels.
A
ARMED
B
READY
C
D
5828 Keypad with Front Cover Removed
A
ARMED
B
READY
C
D
5828V Keypad with Front Cover Removed
Wireless Bidirectional Fixed-Word Keypads
INSTALLATION AND SETUP GUIDE
1 2 3
OFF AWAY STAY
4 5 6
MAX TEST BYPASS
8 9
7
CODE CHIME
INSTANT
0 #
READY
MIC
MESSAGE
1 2 3
OFF AWAY STAY
RECORD VOLUME PLAY
4 5 6
MAX TEST BYPASS
7 8 9
INSTANT CODE CHIME
0 #
READY
STATUS VOICE FUNCTION
ADEMCO 5828/5828V
Operation (See NOTE below)
1. Battery-Powered Operation:
battery, the keypads activate when any key is pressed.
When the key is pressed, the keypad sends a status request
to the control. The keypad displays and/or annunciates the
present system status transmitted by the system.
2. AC-Powered Operation:
keypad remains active at all times
status will cause the display to automatically turn on (if
blank) and display/annunciate the new status.
If AC power is lost, the keypad will revert to battery-powered
operation until AC power is restored and a new status
request is made.
NOTE: Whether the unit is powered by battery or AC, the
5828/5828V may take up to 5 seconds to display and/or
annunciate the new status after pressing the [✱] key.
WALL MOUNTING
Before mounting the 5828 & 5828V permanently,
determine a good RF location as follows:
•
If interfacing to a LYNX panel, try communicating
with the panel from different locations.
•
If interfacing to a VISTA panel, perform a Go/No
Go test from the panel. Refer to the Go/No Go test
mode in the Installation and Setup Guide for the
panel.
Avoid mounting locations on or near large metal objects,
since these can decrease the transmission range or block
transmissions.
•
Secure the mounting plate to the wall, using proper sized
hardware through the six mounting holes.
•
Route the wires from the optional power pack through
the wire guides on the back of the keypad and into the
hole in the back of the keypad.
•
Plug the AC adaptor connector into the keypad's DC
input connector.
•
Position the keypad over the mounting plate and slide
down, engaging the four retaining clips on the plate with
the receptacles on the keypad.
DESKTOP MOUNTING
For full portability, the keypad may be placed in any conve-
nient, RF-suitable location and operated in its battery-
powered mode, or near an AC outlet to be powered by the
optional Power Pack/Desktop Mounting Kit, ADEMCO P/N
5828DM.
BATTERY INSTALLATION OR REPLACEMENT
CAUTION: Remove the AC/DC power connector from the
keypad (if applicable), before attempting to install or replace
the batteries.
Separate the keypad from its mounting plate by sliding the
keypad up and away from the mounting plate.
Open the battery compartment door to expose the batteries.
K0020V1 7/04 Rev. A
When powered by
When powered by AC, the
. Any change in system