Page 1 LEON Owner’s manual...
Page 2 Foreword This Instruction Manual and its corresponding supplements should be read carefully to familiarise yourself with your vehicle. Besides the regular care and maintenance of the vehicle, its correct handling will help preserve its value. For safety reasons, always note the information concerning accessories, modifications and part replace- ments.
Page 4: Table Of Contents
Emergency locking and unlocking ... . Seat belts .......
Page 5 Table of Contents Trailer Changing tail light bulbs (on rear lid) ..........Changing number plate light bulbs .
Page 6: Manual Structure
Because this is a general manual for the LEON, some of the equipment and For the sake of the environment functions that are described in this manual are not included in all types or Texts preceded by this symbol contain relevant information concerning envi- variants of the model or model year;...
Page 7: Content
2. Operating instructions Information about the distribution of controls in the driver position of your vehicle, about the seat adjustment possibilities, about how to create a suit- able climate in the vehicle interior, etc. 3. Practical Tips Advice relating to the driving, caring and maintenance of your vehicle and certain problems you can solve yourself.
Page 8: Safety First
The following list includes most of the safety equipment in your SEAT: safety and for your passengers' safety.
Page 9 – Assume the correct sitting position. Instruct your passengers al- so to assume a proper sitting position. ⇒ p age 10. – Fasten your seat belt securely. Instruct your passengers also to Before starting every trip fasten their seat belts properly. ⇒ p age 19.
Page 10: Safe Driving
Safe driving – Always reduce your speed as appropriate for road, traffic and weather conditions. – When travelling long distances, take breaks regularly - at least every two hours. – If possible, avoid driving when you are tired or stressed. WARNING When driving safety is impaired during a trip, the risk of injury and acci- dents increases.
Page 11: Sitting Position For Vehicle Occupants
● Always keep your feet on the footwell when the vehicle is moving; WARNING never rest them on the dash panel, on the window or on the seat! An in- ● The front seats, head restraints and seat belts must always be adjus-...
Page 12 25 cm between the steering wheel and the centre of your chest ⇒ F ig. – Move the driver seat forwards or backwards so that you are able to press the accelerator, brake and clutch pedals to the floor with your knees still slightly angled ⇒ .
Page 13 ● An incorrect sitting position of the driver can lead to severe injuries. dash panel so that the airbag can provide the greatest pos- ● Adjust the driver seat so that there is at least 25 cm distance between sible protection in the event that it is triggered.
Page 14 ● Always keep your feet in the footwell when the vehicle is moving; never rest them on the dash panel, out the window or on the seat. An in- – Always keep both feet in the footwell in front of the rear seat.
Page 15 Safe driving Correct adjustment of front seat head restraints Adjust the head restraint correctly in order to achieve maximum protection. Properly adjusted head restraints are an important part of – Adjust the head restraint so that its upper edge is at the same...
Page 16 – The rear head restraints have 2 positions: use and non-use. injury due to incorrect seat belt position. As the driver, you are re- sponsible for all passengers, especially children.
Page 17: Pedal Area
● Never put your feet out of a window. clutch pedals unimpaired to the floor. ● Never put your feet on the dash panel. ● Never put your feet on the surface of a seat. – Ensure that the pedals can return unimpaired to their initial po- sitions.
Page 18: Storing Objects
Safe driving Floor mats on the driver side – Distribute the load evenly in the luggage compartment. – Place heavy objects as far forward as possible in the luggage Only floor mats may be used which can be securely fastened compartment.
Page 19 ● Never transport passengers in the luggage compartment. All vehicle ● If pieces of luggage or other objects are secured to the fastening occupants must have their seat belt fastened ⇒ p age 19. rings with inappropriate or damaged retaining cords, injuries could be sustained in the event of braking manoeuvres or accidents.
Page 20: Seat Belts
Seat belt warning lamp*  WARNING The control lamp acts as a reminder to the driver to fasten ● If seat belts are worn incorrectly or not at all, the risk of severe inju- the seat belt. ries increases. ● Properly worn seat belts can reduce severe injuries in case of sudden Before starting the vehicle: braking manoeuvres or accidents.
Page 21 30 km/h (20 mph). The warning lamp*  is switched off if the driver seat belt is fastened while the ignition is switched on. ...
Page 22: Why Wear Seat Belts
25 km/h (15 mph) to 50 km/h (30 mph), for example, the kinetic energy is multiplied by four. Because the vehicle occupants in our example are not restrained by seat belts, all of the occupants' kinetic energy has to be absorbed at the point of ⇒ ...
Page 23 The airbag system is not a substitute for seat belts. When triggered, airbags provide only additional protection. All occupants (including the driver) must wear seat belts properly at all times during the trip. This will reduce the risk Fig. 8 A driver not wear- of severe injuries in the event of an accident –...
Page 24 Our examples describe frontal collisions. Of course, properly worn seat belts substantially reduce the risk of injury in all other types of accidents. This is why it is so important to fasten seat belts before every trip, even when "just driving around the corner".
Page 25 ● The seat belt should never lie on hard or fragile objects (such as glasses or pens, etc.) because this can cause injuries. ● Do not allow the seat belt to be damaged or jammed, or to rub on any sharp edges.
Page 26: Seat Belts
● Never put the latch plate in the buckle of another seat. If you do this, the seat belt will not protect you properly and the risk of injury is in- Fig.
Page 27 ● An incorrectly worn seat belt can cause severe injuries in the event of an accident. ● The shoulder part of the seat belt must lie on the centre of the shoul- der, never across the neck. The seat belt must lie flat and snugly on the ⇒ ...
Page 28 ● For pregnant women, the lap part of the seat belt must lie as low as possible over the pelvis, never across the stomach, and always lie flat so that no pressure is exerted on the abdomen.
Page 29: Seat Belt Tensioners
WARNING properly and to wear them for the whole journey. Never unbuckle a seat belt while the vehicle is in motion. If you do, you ● Read and always observe information and warnings concerning the increase the risk of sustaining severe or fatal injuries.
Page 30 ● Any work on the belt tensioners and seat belts, including the removal ● If the seat belt tensioners are triggered, a fine dust is produced. This is and refitting of system parts in conjunction with other repair work, must normal and it is not an indication of fire in the vehicle.
Page 31: Airbag System
● If you are not wearing a seat belt, if you lean forward or to the side you critical injuries. Therefore, it is essential that all vehicle occupants as- while travelling or assume an incorrect sitting position, there is a sub- sume a correct sitting position while travelling.
Page 32 WARNING ● To reduce the risk of injury from an inflating airbag, always wear the ● If a child seat is secured to the front passenger seat, the risk to the seat belt properly ⇒ p age 19. child of sustaining critical or fatal injuries in the event of an accident in- ●...
Page 33 Airbag system Types of front passenger front airbag systems There are two different SEAT front passenger front airbag systems: Characteristics of the front passen- Characteristics of the front passen- ger front airbag that can only be dis- ger front airbag that can be disabled manually ⇒ ...
Page 34 Digit Possible cause Solution Have the system checked immediately by a specialised  Instrument panel Fault in airbag system and seat belt tensioners. workshop. Have the system checked immediately by a specialised Fault in the airbag system.   workshop.
Page 35 ● Never mount a child seat in the front passenger seat or remove the mounted child seat! The front passenger front airbag may deploy during ●...
Page 36: Front Airbags
The airbag system is not a substitute for seat belts, but it is an integral part of the vehicle's overall passive safety system. Please bear in mind that the...
Page 37 ● there is a rear-end collision ● the vehicle turns over WARNING ● The seat belts and airbags can only provide maximum protection if the occupants are seated correctly ⇒ p age 10, Sitting position for vehicle occupants. ● If a fault has occurred in the airbag system, have the system checked immediately by a specialised workshop.
Page 38 ● If you are not wearing a seat belt, if you lean forward or to the side while travelling or assume an incorrect sitting position, there is a sub- stantially increased risk of injury.
Page 39: Knee Airbag
● Never not fix objects to the cover or in the deployment area of the knee airbag. ● Adjust the driver seat so that there is a distance of at least 10 cm (4 inches) between your knees and the location of the knee airbag. If you physical constitution prevents you from meeting these requirements, Fig.
Page 40: Side Airbags
Airbag system Side airbags* The airbag system is not a substitute for seat belts, but it is an integral part of the vehicle's overall passive safety system. Please bear in mind that the airbag system can only work effectively when the occupants are wearing their seat belts.
Page 41 ● Any work carried out to the doors should be made in an authorised specialised workshop. ● The seat belts and airbags can only provide maximum protection if the occupants are seated correctly ⇒ p age 10, Sitting position for vehicle occupants.
Page 42 This ● If you do not wear a seat belt, if you lean forward, or are not seated is particularly the case if the child is travelling on the front passenger correctly while the vehicle is in motion, you are at a greater risk of injury seat and the airbag system is triggered in an accident;...
Page 43: Curtain Airbags
Fully inflated airbags reduce the risk of head or chest injury in a side collision. The airbag system is not a substitute for seat belts, but it is an integral part of the vehicle's overall passive safety system. Please bear in mind that the...
Page 44  ● In order for the side airbags to provide their maximum protection, the prescribed sitting position must always be maintained with seat belts fastened while travelling. ● For safety reasons, the curtain airbag must be disabled in those vehi- cles fitted with a screen dividing the interior of the vehicle.
Page 45: Deactivating Airbags
The deactivation of airbags corresponds only to certain cases, i.e. if: lights up with the word      placed in the centre part of the ● a child seat is required in the front passenger seat with the child facing ⇒ F ig.
Page 46 Airbag system Front passenger front airbag switch – Open the glove compartment on the front passenger side. – Turn the airbag switch slot with the key to the OFF position ⇒ F ig. – Check, with the ignition switched on, that the control lamp  ⇒ ...
Page 47 Airbag system WARNING ● The driver of the vehicle is responsible for disabling or switching on the airbag. ● Always switch off the ignition before disabling the front passenger airbag! Failure to do so could result in a fault in the airbag deactivation system.
Page 48: Child Safety
Depending on their age, height and weight, children trav- elling on the rear seat must use a child seat or a seat belt. For safety rea- Proper use of child seats substantially reduces the risk of in-...
Page 49 However, if it is necessary, in excep- ● Do not allow the seat belt to become twisted or jammed, or to rub on tional cases, to transport a child in the front passenger seat, the front any sharp edges.
Page 50: Child Seats
Child seats that have been tested and approved under the ECE R44 stand- ard bear the test mark on the seat (the letter E in a circle with the test num- Group 0+: Infants up to 13 kg (approx. 18 months) must travel in the direc- ber below it).
Page 51 ⇒ p age 47. logue. These child seats have been designed and tested for use in SEAT ve-  hicles. You can find the right child seat for your model and age group at SEAT dealers. Group 1 child seats...
Page 52 SEAT recommends the use of child seats from the Original Accessories cata- logue. These child seats have been designed and tested for use in SEAT ve- hicles. You can find the right child seat for your model and age group at SEAT dealers.
Page 53: Securing Child Seats
15 to 25 kg Group III You can secure a child seat to the rear seat or front passenger seat in the 22 to 36 kg following ways: Suitable for universal restraint systems for use in this mass group.
Page 54 However, if, in exceptional cases, it is necessary to transport a child in the front passenger seat, the front pas- senger airbag ⇒ p age 44 must always be disabled and the seat adjusted to its backmost highest position, where possible.
Page 55 Two “ISOFIX” retaining rings are fitted on each rear seat. In some vehicles, To understand the compatibility of the "ISOFIX" systems in the vehicle, con- the rings are secured to the seat frame and, in others, they are secured to sult the table below.
Page 56 ● Never secure child seats that do not have the ISOFIX and Top Tether* – Do a test by pulling both sides of the car seat to ensure that it is system, retaining belts or other objects to the securing rings – this could properly anchored.
Page 57 The objective of the retainer strap is to reduce forward movements of the seat is correctly secured to the anchor on the back of the rear child seat in a crash, helping reduce the risk of injuries to the head from hit- seat.
Page 58 Child safety Safety First Operating instructions Practical Tips Technical specifications...
Page 59 Controls and displays Fig. 35 Controls and displays...
Page 60: Operating Instructions
Door handle – SEAT driving modes ........
Page 61 Controls and displays Ignition lock ..........Knee airbag .
Page 62: Instruments And Warning/Control Lamps
Introduction Additional information and warnings: ● Control and warning lamps ⇒ p age 69 ● SEAT information system ● Easy Connect system ● Gear engaged display (automatic gearbox) ⇒ p age 154. ● Instructions for inspection intervals ⇒ B ooklet Maintenance Programme WARNING Any distraction may lead to an accident, with the risk of injury.
Page 63 Instruments and warning/control lamps ⇒ F ig. ● Bonnet, rear lid and doors open CAUTION ● Information and warning texts ● To prevent damage to the engine, the rev counter needle should only re- ● Mileage main in the red zone for a short period of time. ●...
Page 64 Instruments and warning/control lamps ⇒ F ig. 37 Illustration Key to Type of mes- Symbol Description sage colour  Do not continue driving! ⇒ p age 209 The bonnet is open or is not properly Symbol flashing or lit; partly combined with audible warnings.
Page 65 Instruments and warning/control lamps The time can also be set via the key and function button in the Speed warning Setup  Easy Connect system ⇒ p age 79. When the speed setting is exceeded, this will be indicated on the instru- ment panel display.
Page 66 Technical progress has made it possible to considerably reduce servicing re- ● Never rely on the outside temperature indicator! quirements. The technology used by SEAT ensures that your vehicle only has an Interval Service when it is necessary. To establish when the Interval Service is due (max.
Page 67 The service interval display is reset We recommend that you avoid high revs and that you follow the recommen- If the service was not carried out by a SEAT dealership, the display can be dations on the gear-change indicator. Consult the additional information in reset as follows: ⇒ ...
Page 68 Instruments and warning/control lamps Trip recorder Fuel level ⇒ F ig. 36 The display only works when the ignition is switched on. When the display reaches the reserve mark, the lower diode lights up in red and the control lamp  appears ⇒ p age 207. When the fuel level is very low, the lower diode flashes in red.
Page 69 Instruments and warning/control lamps Gear-change indicator Normal temperature If in normal operations, the diodes light up until the central zone, it means This additional indicator function can help to save fuel. that the engine has reached operating temperature. At high outside temper- atures and when making the engine work hard, the diodes may continue lighting up and reach the upper zone.
Page 70: Control Lamps
Depending on the model, additional text messages may be viewed on the instrument panel display. These may be purely informative or they may be  ⇒ p age 19 Driver or passenger has not fastened seat belt.  advising of the need for action ⇒ p age 61, Instruments. Safety First...
Page 71  Rear fog light switched on. Engine oil level insufficient. On the instrument panel display:  Fault in airbag system and seat belt tensioners. ⇒ p age 252 Driving light totally or partially faulty.  On the instrument panel display: ...
Page 72 Instruments and warning/control lamps Symbol Meaning ⇒ Symbol Meaning ⇒ On the instrument panel display:  ⇒ p age 168  ⇒ p age 65 Lane Assist is switched on, but not active. Service interval display. On the instrument panel display: On the instrument panel display: ...
Page 73 Instruments and warning/control lamps WARNING (Continued) ● Before opening the bonnet, switch off the engine and allow it to cool. ● In any vehicle, the engine compartment is a hazardous area and could cause severe injuries ⇒ p age 209. CAUTION Failure to heed the control lamps and text messages when they appear may result in faults in the vehicle.
Page 74: Driver Information System
■ A specialised workshop will be able to programme or modify additional MFD from refuelling ■ functions, according to the vehicle equipment. SEAT recommends visiting a ■ MFD total calculation SEAT Official Service. Assist systems ⇒ t able on page 75 Some menu options can only be read when the vehicle is at a standstill.
Page 75 Driver information system Operating the instrument panel menus ● If managed from the windscreen wiper lever: To display the main menu ⇒ p age 75 or to return to the main menu from another menu, hold the ⇒ F ig. 40 rocker switch down ●...
Page 76 Driver information system Button for the driving assistance systems Menu Function Information instructions from the activated navigation system: When a route guidance is activated, the turning arrows and prox- imity bars are displayed. The appearance is ⇒ B ooklet Navi- similar to the Easy Connect system.
Page 77 Driver information system Multifunction display memory Personalising the displays The multifunction display is equipped with three memories that work auto- In the Easy Connect system you can adjust which of the possible displays of matically: MFD from departure, MFD from refuelling, MFD total calculation. the MFD can be shown on the instrument panel display with the button ...
Page 78 . With the button move to the oil temperature gauge.  When two people use a vehicle, SEAT recommends that each person always uses their own remote control key. When the ignition is switched off, or the Safety First Operating instructions...
Page 79 Driver information system Vehicles with multifunction steering wheel reduce the fuel consumption of your vehicle. The displays appear automatically and will only be shown with the efficiency pro- – To display the engine oil temperature, enter the submenu Jour- gramme. After a time, the saving tips will disappear automatically. and turn the thumbwheel until the oil temperature dis- ney data play appears.
Page 80: Introduction To The Easy Connect System
Introduction to the Easy Connect system* Introduction to the Easy Connect system* System settings (CAR)* Pressing the menu button will always take you to the last menu used. Introduction Function buttons in the vehicle’s settings menu Page ⇒ p age 79 ESC system To select the settings menus, press the Easy Connect button and the...
Page 81 Introduction to the Easy Connect system* – Switch on the Easy Connect system. – Press the button to open the Tyre settings menu. Tyre – Press the Easy Connect button  When the function button check box is activated , the function is active. –...
Page 82 Introduction to the Easy Connect system* – Press the function button to open the Driver as- When the function button check box is activated , the function is active. Driver assistance settings menu. sistance Pressing the menu button will always take you to the last menu used. ...
Page 83 Introduction to the Easy Connect system* Pressing the menu button will always take you to the last menu used. – Press the function button to open the Visibility settings Visibility  menu. Menu Submenu Possible setting Description Light Assist, sensitivity, When the function button check box is activated , the function is active.
Page 84 Introduction to the Easy Connect system* – Press the function button to open the Open- – Press the function button to open the Multi- Opening and closing Multifunction Display menu. menu. ing and closing settings function Display settings When the function button check box is activated , the function is active. When the function button check box is activated , the function is active.
Page 85 Introduction to the Easy Connect system* menu menu Date and Time settings Units Settings The menu options will vary depending on the sound system – Switch the ignition on. fitted in the vehicle. – Switch on the Easy Connect system. –...
Page 86 Menu Submenu Possible setting Description multifunction dis- play. Chassis number, date of next SEAT Any changes made using the settings menus are automatically saved on ⇒ p age 61 Service – service inspection, closing those menus. date of next oil change service.
Page 87: Opening And Closing
Opening and closing Opening and closing Central locking system Anti-theft security system (Safelock) The following message is displayed on the instrument panel to remind the driver that when the vehicle is closed from the outside, the anti-theft securi- Description ty system is switched on. ...
Page 88 ⇒ p age 95. the vehicle is locked, the central locking system or anti-theft alarm* is not working properly. You should have the fault repaired at a SEAT Official Serv- Turn signals ice or specialised workshop.
Page 89 Vehicle key The vehicle keys or new spare keys can be obtained from a SEAT Official Service, a specialised workshop or an approved key service qualified to cre- With the vehicle key the vehicle may be locked or unlocked remotely ate this kind of key.
Page 90 Opening and closing Control lamp on the vehicle key CAUTION All of the vehicle keys contain electronic components. Protect the vehicle keys from damage, impacts and humidity. Note ● Only use the key button when you require the corresponding function. Pushing the button unnecessarily could accidentally unlock the vehicle or trigger the alarm.
Page 91 ● Unfold the vehicle key shaft ⇒ p age 88. SEAT recommends you ask a specialised workshop to replace the battery. ● If necessary, remove the cover from the driver door lever ⇒ p age 97.
Page 92 Opening and closing Remote unlocking/Locking The vehicle will be locked again automatically if you do not open one of the doors or the rear lid within 30 seconds after unlocking the car. This function prevents the vehicle from remaining unlocked if the unlocking button is pressed by mistake.
Page 93 Opening and closing Unlocking all the doors, the rear lid and the tank flap Programming the Auto Lock (vehicles with Easy Connect) simultaneously. – Select: control button Systems or Vehicle systems > Vehicle set- – Within 5 seconds, press button on the remote control key >...
Page 94: Anti-Theft Alarm System
Opening and closing Central locking switch WARNING ● The central locking switch also operates when the ignition is switch- ed off and automatically locks all the vehicle doors when the button  pressed. ● The central locking switch does not operate if the vehicle is locked from the outside and the anti-theft security system is switched on.
Page 95 Opening and closing ● When the door is mechanically unlocked using the vehicle key without ● If the driver door is unlocked mechanically with the key, only the driver turning the ignition within the following 15 seconds. door is unlocked, the rest of the doors remain locked. Only when the igni- tion has been turned on will the other doors be available - but not unlocked ●...
Page 96 Opening and closing The vehicle interior monitoring and anti-tow sensor (tilt sensor) are auto- ● The vibration of a mobile phone left inside the vehicle may cause the ve- matically switched on when the anti-theft alarm is switched on. In order to hicle interior monitoring alarm to trigger, as both sensors react to move- activate it, all the doors and the rear lid must be closed.
Page 97: Emergency Locking And Unlocking
Opening and closing – When the vehicle is locked now, the vehicle interior monitoring WARNING and the tow-away protection are switched off until the next time the door is opened. Opening and closing doors carelessly can cause serious injury. ● If the vehicle is locked from outside, the doors and windows cannot If the anti-theft security system (Safelock)* ⇒ ...
Page 98 Opening and closing Unlocking or locking the driver door Unlocking notes: ● The anti-theft alarm will remain active when vehicles are unlocked. How- If the central locking system should fail to operate, the driver ever, the alarm will not yet be triggered ⇒ p age 86. door can still be locked and unlocked by turning the key in ●...
Page 99: Rear Lid (Luggage Compartment)
Opening and closing Opening the rear lid A mechanical locking device (only visible when the door is open) is provided on the front passenger door. ⇒ F ig. – Pull on the release lever and lift the rear lid 54. The rear lid will automatically open.
Page 100 – Insert the key in the opening in the lining of the rear lid be activated or deactivated at a SEAT Authorised Service, which will provide move the key in the direction of the arrow until the lock is re- all of the necessary information.
Page 101: Electric Windows
Opening and closing Electric windows Button for window in rear left door Button for window in rear right door Safety switch for deactivating the electric window buttons in the rear Electronic control of windows* doors The front and rear electric windows can be operated by us- Safety switch * ing the controls on the driver door.
Page 102 Opening and closing – Keep the key in the driver door in the "lock" position until all the WARNING (Continued) windows and the sliding/tilting sunroof* are closed. ● The electric windows will work until the ignition has been switched off and one of the front doors has been opened. Programming convenience opening in the Easy Connect* ●...
Page 103 Opening and closing One-touch opening ● If the window is still obstructed, the window will stop at this point. ● If there is no obvious reason why the window cannot be closed, try to – Push down the window button briefly up to the second position. close it again by pulling the tab within ten seconds.
Page 104: Panoramic Sliding Sunroof
Opening or closing the panoramic sliding sunroof Introduction Additional information and warnings: ● SEAT information system ⇒ p age 73 ● Central locking and locking system ⇒ p age 86 WARNING Careless or uncontrolled use of the panoramic sliding sunroof can cause Fig.
Page 105 Opening and closing Panoramic sliding sunroof: operation Function Switch setting Necessary operations ⇒ F ig. 57 Convenience open/close function To open the sliding The panoramic sliding sunroof can be opened or closed from outside the sunroof completely: vehicle using the vehicle key: To choose the con- venience position Rotate the switch to the re-...
Page 106 Opening and closing Closing without the roll-back function ⇒ F ig. 57 ● The switch should be in the “closed” position ● Within five seconds of triggering the roll-back function, pull the control ⇒ F ig. 58 all the way back (arrow ) until the panoramic sliding sunroof closes fully.
Page 107: Lights And Visibility
Lights and visibility Lights and visibility Lights Control lamps lights up Possible cause Solution Introduction Replace the corresponding bulb ⇒ p age 252. Driving light totally or partially The legal requirements regarding the use of vehicle lights in each country ...
Page 108 Lights and visibility Right turn signal. Right-hand parking light (ignition switched off) WARNING ⇒ p age 109. Left turn signal. Left-hand parking light (ignition switched off) If the warning lamps and messages are ignored, the vehicle may stall in ⇒ p age 109. traffic, or may cause accidents and severe injuries.
Page 109 Lights and visibility Symbol if the ignition is switched off when the ignition is on Note  ● The turn signal only works when the ignition is switched on. The hazard Side light on. Side light on. warning lights also work when the ignition is switched off. Dipped beam off;...
Page 110 Lights and visibility Lights and visibility: functions When the light switch is in position , the vehicle lights and the instru- ment panel and switch lighting switch on and off automatically in the fol- lowing situations ⇒ Parking light When the parking light is switched on, (right or left turn signal), the front Automatic switching on: Automatic switching off: side light and the rear light on the corresponding side of the vehicle stay lit.
Page 111 Lights and visibility Hazard warning lights  WARNING The hazard warning lights are used to draw the attention of If the road is not well lit and other road users cannot see the vehicle well other road users to your vehicle in emergencies. enough or at all, accidents may occur.
Page 112 Lights and visibility 7. Always take the vehicle key with you when you leave the vehi- Note cle. ● The battery will run down if the hazard warning lights are left on for a long time, even if the ignition is switched off. Switch on the hazard warning lights to warn other road users, for example: ●...
Page 113 Lights and visibility Switching the main beam assist on and off WARNING Function Action The convenience features of the main beam assist should not encourage – Switch the ignition on and turn the light switch to position the taking of risks. The system is not a replacement for driver concentra- .
Page 114 The light distribution that the halogen and full-LED headlights of the SEAT – Automatically, if 30 seconds after coming on, a vehicle The system Leon range have, allows the specific “tourist light” values to be met without door or the rear lid remains open. switches off: the need for stickers or changes in the settings.
Page 115 Lights and visibility Headlight range control, lighting of the instrument panel Value Vehicle load status and controls All seats occupied, luggage compartment full With trailer and minimum drawbar load Driver only, luggage compartment full With trailer and maximum drawbar load If the vehicle load does not correspond to those shown in the table, it is possible to select intermediary positions.
Page 116: Sun Blind
Lights and visibility Interior and reading lights the radio menu (see Easy Connect > Adjusting Lights > Interior lighting ⇒ p age 81). Button/ Function Note Switch The reading lights switch off when the vehicle is locked using a key or after ...
Page 117: Windscreen Wiper System
Lights and visibility Sun visors Windscreen wiper system Introduction Additional information and warnings: ● Changing wheels round ● Heating, ventilation, cooling ● Caring for and cleaning the vehicle exterior WARNING If the water from the windscreen washer does not contain enough anti- freeze, it may freeze on the windscreen, reducing forward visibility.
Page 118 Lights and visibility Control lamp lights up Possible cause Solution Top up the windscreen wiper Windscreen wiper fluid level  reservoir as soon as possible too low ⇒ p age 121. Several warning and control lamps should light up for a few seconds when the ignition is switched on, signalling that the function is being verified.
Page 119 ● If necessary, remove snow and ice from the windscreen wipers before starting your journey. ● Carefully lift the frozen windscreen wipers from the glass. SEAT recom- mends a de-icer spray for this operation. CAUTION Do not switch on the windscreen wipers if the windscreen is dry. Cleaning Fig.
Page 120 Lights and visibility Windscreen wiper functions Note The wiper will try to wipe away any obstacles that are on the windscreen. Windscreen wiper performance in different situations: The wiper will stop moving if the obstacle blocks its path. Remove the ob- If the vehicle is at a stand- The activated position provisionally changes stacle and switch the wiper back on again.
Page 121 Lights and visibility Lifting and returning windscreen wiper arms ● Place the wiper arms in the service position ⇒ . ● Only hold the wiper arms at the point where the blade is fixed. CAUTION ● To prevent damage to the bonnet and the wiper arms, only leave them in the service position.
Page 122 (arrow). ● To top up, mix water with a window cleaner recommended by SEAT ⇒ . ● To remove wax and coatings, we recommend a window cleaner contain- Please follow the instructions for use found on the packaging.
Page 123: Rear Vision Mirror
CAUTION – In these positions you can adjust the exterior mirrors (left or right) by ● Do not mix cleaning products recommended by SEAT with other prod- moving the control in the desired direction. ucts. This could lead to flocculation and may block the windscreen washer –...
Page 124 Lights and visibility Anti-dazzle rear vision mirrors ● If necessary the right exterior mirror adjustment may need correcting. Turn the knob to position R. Your vehicle is fitted with an interior rear vision mirror with a ● In the Easy Connect system the exterior mirrors can be adjusted using manual or automatic control for anti-dazzle position.
Page 125 Lights and visibility WARNING In the event that an automatic anti-dazzle rear vision mirror breaks, an electrolyte fluid may leak. This could cause irritation to the skin, eyes and respiratory organs. If you come into contact with this liquid, it must be rinsed with large quantities of water.
Page 126: General Notes
Manual seat adjustment ● The front seat backrests must not be reclined for driving. Otherwise, seat belts and the airbag system might not protect as they should, with the subsequent danger of injury.  Front centre armrest The centre armrest can be adjusted to various levels.
Page 127: Seat Functions
The seat cushions can be heated electrically when the ignition is switched on. The backrest is also heated in some versions. The seat heating should not be engaged in any of the following conditions: Introduction ● The seat is unoccupied.
Page 128: Head Restraints
● Do not spill liquid on the seat. CAUTION ● To avoid damaging the heating elements of the seat heating, please do not kneel on the seat or apply sharp pressure at a single point to the seat cushion and backrest. Fig. 73 Front seat: ad- ●...
Page 129 ● Remove the rear head restraints only when it is necessary for the button and move it downwards. placement of a child seat ⇒ p age 47. After removing a child seat, remount the head restraint immediately. Travelling with the head restraints re- Removing the head restraint moved or improperly adjusted increases the risk of severe injuries.
Page 130: Storage
Seats and storage Power socket CAUTION Electrical equipment can be connected to the 12 volt power Always use the correct type of plugs to avoid damaging the sockets. socket. Note The use of electrical appliances with the engine switched off will cause a battery discharge.
Page 131: Glove Compartment
The load of the compartment should not exceed 0.2 kg. ● Coat hooks in the pillar B ⇒ Fig. 77 Glove compart- ● Other storage compartments are found in the rear seat, to the left and ment the right of the seats.
Page 132: Luggage Compartment
 mend roof carriers and structures from the SEAT accessories programme. ● When mounting the roof carrier, be sure to mount only on the points al- ready provided on the roof. The front and rear attachment points are only visible when the doors are open.
Page 133 Seats and storage Luggage compartment cover WARNING The luggage compartment cover blocks the view into the ● The luggage compartment cover must always be fixed properly (risk luggage compartment. of accident). ● The luggage compartment cover should not be used as a storage shelf.
Page 134  ● When returning the backrest to an upright position, make sure that the side seat belts are not caught up and damaged in the catches for the back- rest.  Safety First...
Page 135: Air Conditioning
● Never leave the fresh air fan turned off or use the air recirculation for ● Easy Connect system long periods of time; the air in the vehicle interior will not be refreshed.  ● Seat functions ● Windscreen wipers and washers ● Caring for and cleaning the vehicle exterior...
Page 136 Note ● When the cooling system is turned off, air coming from the outside will not be dried. To prevent fogging of the windows, SEAT recommends leaving the cooling system (compressor) turned on. To do this, press the button ...
Page 137  Air recirculation ⇒ p age 141. Operating by using the Easy Connect* system (valid for   Buttons for seat heating ⇒ p age 126. Radio Entry)  Press the button to switch on or off the cooling system.
Page 138 Air conditioning To switch a function on or off, or to select a submenu, you must press the Function button Function corresponding function button. Adjust the fan level in AUTO mode. You can choose be- Air conditioning profile tween low, medium and high. For more information about functions ⇒ ...
Page 139 Control but- Additional information. Manual air conditioning system. Additional information. Manual air conditioning system. Temper-   Buttons for seat heating ⇒ p age 126. Rotate the control to set the temperature accordingly. ature  ...   Turn the control to the position   to make maximum cooling capacity available.
Page 140 Air conditioning ● Open and direct all the air outlets in the dash panel. Control but- ● Turn the air distribution control to the desired position. Additional information. Heating and fresh air system Rotate the control to adjust the temperature accordingly. The Temper- WARNING desired temperature for the interior cannot be lower than...
Page 141 Air conditioning ● Turn the air distribution control to the required position. Note ● Press the button to switch on the cooling system. The button will  After starting the engine, any residual humidity in the air conditioner could light up. mist over the windscreen.
Page 142: Air Recirculation
Air conditioning There are other additional, non-adjustable air vents in the dash panel , in Functioning mode of manual air recirculation (air conditioning menu) the footwell and in the rear area of the interior. With the automatic air recirculation mode activated, the entry of fresh air in- to the cabin interior is enabled.
Page 143 Air conditioning CAUTION Do not smoke when air recirculation is switched on in vehicles with an air conditioner. The smoke taken in could lie on the cooling system vaporiser and on the activated charcoal cartridge of the dust and pollen filter, leading to a permanently unpleasant smell.
Page 144: Driving
Driving Driving Steering WARNING ● Never adjust the position of the steering wheel when the vehicle is Adjusting the steering wheel position moving, as this could cause an accident. ● Move the lever up firmly so the steering wheel position does not acci- The height and reach of the steering wheel can be freely ad- dentally change during driving.
Page 145: Ignition Lock
Driving Ignition lock Switching the ignition on/off, preheating – Turn the ignition key to position to switch on the ignition. Starting the engine with the ignition key – Turn the ignition key to position to switch off the ignition. Switch on the ignition with the key in the ignition and start Preheating is produced in Diesel vehicles ...
Page 146 Driving Start-Stop System* WARNING If the vehicle is stopped and the Start-Stop system* switches off the engine, the ignition remains switched on. ● Never run the engine in confined spaces, as the exhaust gases are poisonous. Automatic gearbox: Before leaving the vehicle, make sure that the ignition ●...
Page 147: Switching Off Engine With Key
● Never remove the key from the ignition if the vehicle is in motion. * ⇒ p age 172 mode has been selected in SEAT Drive Mode*, and Otherwise, the steering could lock making it impossible to steer the vehi-...
Page 148: Parking
Driving Handbrake Always apply the handbrake as far as it will go in order to prevent yourself from driving with the handbrake applied by mistake ⇒ The handbrake warning lamp  lights up when the handbrake is applied Using the handbrake and the ignition switched on.
Page 149: Hill Hold Assist
Note ● Depending on weather conditions, it may become extremely hot or The SEAT Official Service or a specialised workshop can tell you if your vehi- cold inside the vehicle. This can be fatal. ...
Page 150: Speed Warning Function
Driving Speed warning function Setting speed limit warning You can use the radio or the Easy Connect* to set, alter or Introduction cancel the speed limit warning. The speed warning function can help prevent you exceeding Vehicles with radio a particular pre-set maximum speed. –...
Page 151 ● The driver door must be closed. Vehicles with a manual gearbox ● The driver must have their seat belt fastened. – When the vehicle is stopped, put it into neutral and release the ● The bonnet must be closed.
Page 152 Driving ● After engaging reverse gear. Note ● In case of a very steep gradient. ● You can control whether the engine should switch off or not by reducing or increasing the brake force applied. While the vehicle remains stopped, The indication ...
Page 153: Manual Gearbox
Driving Manually switching on/off the Start-Stop system Driver messages on the instrument panel display If you do not wish to use the system, you can switch it off Start-Stop system deactivated. Start the engine manually manually. This driver message is displayed when certain conditions are not met during the stopping phase and the Start-Stop system cannot restart the engine.
Page 154 Driving ● Press and hold the clutch pedal to the floor. WARNING ● Place the gearbox lever in the required position ⇒ When the engine is running, the vehicle will start to move as soon as a ● Release the clutch pedal to engage clutch. gear is engaged and the clutch released.
Page 155: Automatic Gearbox/Dsg Automatic Gearbox
Driving Automatic gearbox/DSG automatic gearbox* lights come on when the selector lever is in the R position with the ignition N – Neutral (idling) Introduction With the selector lever in this position, the gear is in neutral. Your vehicle is equipped with an electronically controlled manual gearbox. D/S –...
Page 156 Driving Selector lever lock WARNING (Continued) ● With selector lever in any position (except P) the vehicle must always The selector lever lock prevents gears from being engaged be held with the foot brake when the engine is running. This is because inadvertently, so that the vehicle is not set in motion unin- an automatic gearbox still transmits power even at idling speed, and the tentionally.
Page 157: Driving Tips
Driving The selector lever lock only works if the vehicle is stationary or driving at ● When the vehicle does not move in the required direction, the system speeds up to 5 km/h (3 mph). At higher speeds the selector lever lock in may not have the gear range correctly engaged.
Page 158 Driving Stopping/Parking On level ground it is sufficient to move the selector lever to position P. On slopes, first engage the parking brake and then put the selection lever into If the driver door is opened and the selector lever is not in position the P position.
Page 159 Driving mode may be required. In this case, manually reduce the tiptronic to 2nd or CAUTION 1st gear to use the engine brake and reduce the charge on the brakes. ● If you stop the vehicle on a gradient, do not attempt to stop it from roll- Downhill speed control is deactivated as soon as the road levels out again ing by depressing the accelerator when a gear has been selected.
Page 160 Driving Changing gears in tiptronic mode* – To switch to tiptronic mode, move the selector lever from posi- tion D/S to the right. As soon as the change is made, the selec- The tiptronic gives the driver the option to change gears tor lever will be shown in the position G (i.e.
Page 161 – Move the selector lever to position “S” or tiptronic, or select the layed until the engine reaches maximum rpm. driving mode Sport from the SEAT Drive Mode* ⇒ p age 171. WARNING – Press the brake pedal firmly with your left foot and hold it down for at least one second.
Page 162 Driving – Select Eco mode ⇒ p age 171 once in SEAT Drive Mode*. WARNING – Take your foot off the accelerator. ● Always adapt your driving style to the traffic conditions. ● Only use the Launch control programme when road and traffic condi- The driver message Inertia will be displayed.
Page 163 Seek specialist assistance. Failure to do ● Inertia mode is only available in driving mode (SEAT Drive Mode*). so could cause considerable damage to the gearbox. When the warning switches off, the fault should be corrected by a specialised workshop with- ●...
Page 164 Driving  Gearbox: too hot. Adapt your driving accordingly A screwdriver will be needed to carry out the manual release. Use the flat part of the screwdriver blade ⇒ p age 232. Continue driving at moderate speeds. When the warning lamp switches off, you can continue driving in a normal manner.
Page 165: Driver Assistance Systems
Driver assistance systems Driver assistance systems Cruise control system (CCS)* WARNING (Continued) ● It is dangerous to use a set speed which is too high for the prevailing road, traffic or weather conditions. Introduction ● When travelling down hills, the CCS cannot maintain a constant speed.
Page 166 Driver assistance systems Control lamp lights up Possible cause  Cruise control is active Several warning and control lamps should light up for a few seconds when the ignition is switched on, signalling that the function is being verified. They will switch off after a few seconds. Displayed on the CCS screen Status Fig.
Page 167 Driver assistance systems Operating the cruise control system* Fig. 95 On the left of the Fig. 96 On the left of the steering column: steering column: Third 6- switches and controls for position lever for operat- operating the CCS ing the CCS ⇒ ...
Page 168 Driver assistance systems ⇒ F ig. Position of the switch, operating the switch on the turn signal lever 95, or Function Action ⇒ F ig. 96 by using the third lever Depending on equipment fitted: on the turn signal lever in the RES –...
Page 169: Lane Assist System
● When the area of vision of the camera becomes dirty, covered or is Additional information and warnings: damaged, the Lane Assist system function can be affected. ● SEAT information system ⇒ p age 73 ● Accessories, parts replacement, repairs and modifications ⇒ p age 230 CAUTION...
Page 170 Driver assistance systems Note ● The Lane Assist system has been exclusively developed for driving on paved roads only. ● If the Lane Assist system does not work as described in this chapter, do not use it and contact a specialised workshop. ●...
Page 171 Driver assistance systems Operating mode Control lamps flashes or Possible cause Solution lights up The system can not accurately recog-  Lane Assist active but nise the lane. Please see page 170, not available. The Lane Assist system is not availa- (yellow) ble (the control lamp is lit up yellow).
Page 172: Seat Drive Modes
● When the system does not detect any clear and active steering move- ment during a long period of time. SEAT Drive Mode enables the driver to choose between four profiles or ● Temporarily, in the event of very dynamic driving styles.
Page 173  You can select from Normal, Sport, Eco and Individual. Description Depending on the equipment fitted in the vehicle, SEAT Drive Mode can op- erate on the following functions: Engine Depending on the profile selected, the engine responds more spontaneous- ly or more in harmony with the movements of the accelerator.
Page 174: Tiredness Detection (Break Recommendation)
Additional information and warnings: WARNING ● Easy Connect system ⇒ p age 79 When operating SEAT Drive Mode, pay attention to all traffic. Doing oth- ● Accessories, change a part, repairs and adjustments (information stored erwise could cause an accident.
Page 175 15 minutes, when the ignition is switched off or when the driver has ⇒ F ig. unbuckled their seat belt and opened the door. display 101. The message on the instrument panel display is shown for about 5 seconds, and depending on the case, is repeated.
Page 176: Tyre Monitoring Systems
● Driving for the first time with new tyres at a high speed can cause them to slightly expand, which could then produce an air pressure warning. Introduction ● Only replace used tyres with those authorised by SEAT for the corre- sponding type vehicle. Additional information and warnings: ●...
Page 177 Driver assistance systems Several warning and control lamps light up for a few seconds when the igni- WARNING (Continued) tion is switched on while the function is verified. They will switch off after a ● Tyre pressures which are too high or too low reduce the useful life of few seconds.
Page 178 Driver assistance systems Tyre monitoring indicator There may be a delay in the reaction of the tyre monitoring indicator  or it may not indicate anything under certain circumstances (e.g. sporty driving, snow-covered or unpaved roads, or when driving with snow chains). Calibrating the tyre monitoring indicator After changing the tyre pressure or replacing one or more wheels, the tyre monitoring indicator must be recalibrated.
Page 179: Parking Aid
⇒ p age 181. ● In vehicles without a driver information system, these parameters can be modified in a SEAT Official Service or in a specialised workshop. ● Please observe information on towing a trailer ⇒ p age 182.
Page 180 Driver assistance systems Plus parking aid* ● The display on the Easy Connect screen shows a slight time delay. ● To ensure that the parking aid works properly, the sensors must be kept Plus parking aid assists you audibly and visually when park- clean and free of ice and snow.
Page 181 Driver assistance systems Activating/Deactivating Segments of the visual indication The distance of separation from the obstacle can be estimated using the segments around the vehicle. With certain equipment (Radio Standard), the yellow lines* mark the estimated path, depending on the angle of the turned steering wheel.
Page 182 Driver assistance systems ● Switch the ignition on. Rear volume ● Press button Volume in the rear area  ● Press the function button. Setup Rear sound settings ● Press the function button. Parking and Manoeuvring Frequency (tone) of the sound in the rear area. ●...
Page 183 Driver assistance systems Towing bracket If the trailer power socket is occupied, the rear parking aid sensors will not activate when reverse gear is engaged, or when the button  is pressed. This function may not be covered under warranty if the towing bracket is not factory-fitted.
Page 184: Practical Tips
Intelligent technology Practical Tips Intelligent technology Electronic Stability Control (ESC) Traction control system (ASR) In the event of wheelspin, the traction control system reduces the engine torque to match the amount of grip available. This helps the car to start Description moving, accelerate or climb a gradient.
Page 185 Intelligent technology Multi-collision brake Note In an accident, the multi-collision brake can help the driver by braking to ● The ABS and ASR will only operate correctly if the four wheels have iden- avoid the risk of skidding during the accident, which could lead to further tical tyres.
Page 186: Brakes
Intelligent technology Brakes Disable ASR ASR can be disabled through the Easy Connect system ⇒ p age 79 or by pressing the button. The traction control system will be disabled.  New brake pads The control lamp  will light up. For vehicles with a driver information sys- For the first 400 km (250 miles), new brake pads have not yet reached their tem* the driver will be informed that maximum braking capacity, and need to be “run in”...
Page 187: Electro-Mechanical Steering
Intelligent technology Corrosion CAUTION There may be a tendency for corrosion to form on the discs and dirt to build ● Never let the brakes “drag” by leaving your foot on the pedal when it is up on the brake pads if the vehicle is used infrequently or the brakes are not necessary to brake.
Page 188: Power Management
Intelligent technology Power Management If the warning lamp remains on and the driver indication appears, the power steering could be faulty. Do not continue driving. Seek specialist assistance. This system helps to ensure reliable starting  (in yellow) Steering: System fault! You may continue driving. The power management controls the distribution of electri- If the warning lamp comes on, the steering could react with more difficultly cal energy and thus helps to ensure that there is always...
Page 189 Heating systems in particular use a large battery. In these conditions a large amount of power is consumed, but only amount of electrical power. If you notice, for instance, that the seat heating* a small amount is supplied. The situation is also critical if electrical equip- or the heated rear window is not working, they may have been temporarily ment is in use when the engine is not running.
Page 190: Information Recorded In The Control Units
The events re- ● Seat belt check corder should only be read and deleted by a SEAT Official Service or special- The vehicle control units never record conversations held by passengers in ised workshop.
Page 191: Driving And The Environment
Driving and the environment Driving and the environment Running in the engine WARNING After driving through water, mud, sludge, etc., the braking effect can be A new vehicle should be run in over a distance of 1500 km (1000 miles). For delayed slightly due to moisture build-up on the discs and brake pads.
Page 192: Economic And Ecological Driving
Driving and the environment Economic and ecological driving Never drive until the tank is empty; an irregular supply of fuel can cause faulty combustion. In these cases, unburned fuel reaches the exhaust sys- tem, which can overheat and damage the catalytic converter. Fuel consumption, environmental pollution and wear to the engine, brakes Diesel particulate filter and tyres depends largely on driving style.
Page 193: Environmental Friendliness
(at a high Regular servicing helps in saving fuel even before the engine is started. A setting), the rear window heating and the seat heating*.  well-serviced engine gives you the benefit of improved fuel efficiency as well as maximum reliability and an enhanced resale value.
Page 194 Driving and the environment ● Reduced “vapour emissions” from plastics ● CFC-free refrigerant in air conditioner Compliance with the laws prohibiting the use of: Cadmium, asbestos, lead, mercury, chromate. Manufacturing methods ● Recyclable material for the manufacturing of plastic components ●...
Page 195: Trailer
Trailer Trailer Trailer towing The figures for trailer weights and drawbar loads that are given on the data plate of the towing bracket are for certification purposes only. The correct figures for your specific model, which may be lower than these figures for the towing bracket, are given in the vehicle documentation or in ⇒ ...
Page 196 Trailer Speed Note The stability of the vehicle and trailer is reduced with increasing speed. For ● Towing a trailer places additional demands on the vehicle. We recom- this reason, it is advisable not to drive at the maximum permissible speed mend additional services between the normal inspection intervals if the ve- in an unfavourable road, weather or wind conditions.
Page 197: Retrofitting A Towing Bracket
Trailer Retrofitting a towing bracket* 1040 mm 317 mm It is possible to fit a towing bracket to the rear of the vehicle. 339 mm Fitting a towing bracket ● Driving with a trailer involves an extra effort for the vehicle. Therefore, before fitting a towing bracket, please contact a Technical Service to check whether your cooling system needs modification.
Page 198 In certain versions this may entail fitting a heat insulating plate, which is why it is recommended that you go to a SEAT Dealer. In the event that the plate is not installed correctly, SEAT is exempt from any liability.
Page 199: Care And Cleaning
SEAT Official Services and specialist retailers carry stocks of suitable car High temperatures (for instance due to strong sunlight) further intensify the care materials.
Page 200 Care and cleaning Washing the car by hand ● Never wash tyres with a jet that sprays the water out in a direct stream. This could damage the tyres even if the spray is kept at a distance and only When washing the car by hand, use plenty of water to soften the dirt first, used for a very short time.
Page 201: Plastic Parts
Minor damage to the paint, such as scratches or stone chips, should be touched up without delay before the metal starts to corrode. Suitable touch- up brushes or sprays for your car can be obtained from a SEAT Official Serv- Trims ice.
Page 202 Never leave the cleaning agent on the rims for any lon- with a special cleaner. Your SEAT Official Service will be able to provide you ger than specified in the instructions before rinsing it off. If the wheel clean- with more detailed information.
Page 203: Care Of The Vehicle Interior
Note larly with a vacuum cleaner. This will remove surface dirt which could other- Open Velcro fasteners on clothes can damage the seat upholstery. Make wise be rubbed into the textile material during use. Do not use steam clean- sure that Velcro fasteners are closed.
Page 204: Natural Leather
Natural leather To maintain the value of natural leather you should note the following points: SEAT does everything possible to preserve the genuine qual- ities of this natural product. CAUTION ● Avoid exposing leather to direct sunlight for long periods, otherwise it General information may tend to lose some of its colour.
Page 205 Removing dust and dirt – Treat fat-based, dried-in stains with grease-dissolving spray. – Moisten a cloth just a little and wipe down the seat covers. – Treat less common stains such as ball-pen and other inks, felt- Removing stains tip pens, nail polish, dispersion paint, shoe cream etc.
Page 206 ● Do not remove the seat belts from the vehicle to clean them. ● Do not use chemical cleaning agents on the seat belts, as this can dam- age the webbing. Ensure that the seat belts do not come into contact with corrosive fluids.
Page 207: Checking And Refilling Levels
The correct grade of petrol is listed inside the fuel tank flap. ditives would seriously impair the efficiency of the catalytic converter. ● Only use fuel additives that have been approved by SEAT. Octane boost- The vehicle is equipped with a catalytic converter and must only be run on ing or anti-knock additives may contain metal additives that could seriously unleaded petrol.
Page 208: Diesel Fuel
Checking and refilling levels Diesel Fuel Filling the tank Please note the information on the inside of the fuel tank Filling the tank flap. We recommend the use of Diesel fuel which complies to European standard EN 590. If diesel fuel which meets European standard EN 590 is not availa- ble, the Cetane number (CZ) must, at minimum, be 51.
Page 209 Checking and refilling levels – Close the tank flap. Make sure you hear it click into place. WARNING (Continued) – If the spare fuel canister is made of metal, the filling nozzle must If the automatic filler nozzle is operated correctly, it will switch itself off as be in contact with the canister during filling.
Page 210: Bonnet
Checking and refilling levels WARNING (Continued) Note ● Apply the handbrake. Diesel vehicles are fitted with a protective device that prevents the insertion of the wrong fuel hose . It is only possible to refuel with Diesel nozzles. ● If the vehicle has a manual gearbox, place the lever in neutral; if it has an automatic gearbox, place the selector lever in position P.
Page 211 Checking and refilling levels Check that the windscreen wiper arms are not unfolded. Otherwise CAUTION the paint may be damaged. When changing or topping up service fluids, make absolutely certain that you fill the fluids into the correct reservoirs. Using the wrong fluids could The bonnet can only be unlocked when the driver door is open.
Page 212: Engine Oil
Checking and refilling levels Service intervals WARNING Service intervals can be flexible (LongLife service) or fixed (dependent on time/distance travelled). ● For safety reasons the bonnet must always be completely closed when the vehicle is moving. Therefore, after closing the bonnet, always If the PR code that appears on the back of the “Maintenance Programme”...
Page 213 Checking and refilling levels Vehicles with diesel particulate filter* Engine oil additives The “Maintenance Programme” states whether your vehicle is fitted with a No type of additive should be mixed with the engine oil. The deterioration diesel particulate filter. caused by these additives is not covered by the warranty. Only VW 507 00 engine oil, with reduced ash formation, may be used in die- Note sel engines equipped with particulate filter.
Page 214 Checking and refilling levels – Briefly run the engine at idle speed until the operating tempera- CAUTION ture is reached and then stop. If the oil level is above the area do not start the engine. This could result in damage to the engine and catalytic converter. Contact a Technical Serv- –...
Page 215 Checking and refilling levels – As soon as the oil level is in area , carefully close the cap. WARNING The position of the oil filler opening is shown in the corresponding engine Only change the engine oil yourself if you have the specialist knowledge compartment illustration ⇒ ...
Page 216: Cooling System
The original additives should never be mixed with coolants which are not ways be at least 40 %, even in warm climates where anti-freeze protection is approved by SEAT. Otherwise, you run the risk of causing severe damage to not required.
Page 217 Checking and refilling levels Topping up coolant – Top up the coolant only if there is still coolant in the expansion tank, otherwise you could damage the engine. If there is no Top up coolant when the level is below the MIN (minimum) coolant in the expansion tank, do not continue driving.
Page 218: Brake Fluid
218). These functions will require resetting after the battery is re- in the Service Plan. We recommend you have the brake fluid replaced at a connected. SEAT Official Service, during an Inspection Service. Deactivate the anti-theft alarm* before you disconnect the battery Other- wise the alarm will be triggered.
Page 219 ● Ensure that the vent hose is always connected to the battery. ● Never use damaged batteries. This could cause an explosion! Replace All work on batteries requires specialist knowledge. Please refer to a SEAT a damaged battery immediately. Official Service or a workshop specialising in batteries: risk of burns or ex-...
Page 220 Checking and refilling levels Charging the battery WARNING Terminals for charging the battery are fitted in the engine Never charge a battery that has frozen: replace battery! Failure to do so compartment. may lead to an explosion. – Note the warnings ⇒ in Important safety warnings for han- Note dling a vehicle battery on page 218 and ⇒ ...
Page 221: Windscreen Washer Reservoir And Wiper Blades
Checking and refilling levels ● Before starting any work on the battery, always observe the warnings lis- The windscreen washer reservoir  contains the cleaning fluid for the wind- ted under ⇒ p age 218, Important safety warnings for handling a vehicle ⇒ ...
Page 222 Checking and refilling levels Cleaning and changing the wiper blades of the windscreen ite layer is damaged, the noise of the water as it is wiped across the wind- screen will be louder. and rear window Check the condition of the wiper blades regularly. If the wipers scrape across the glass they should be changed if they are damaged, or cleaned if they are dirty ⇒ ...
Page 223 Checking and refilling levels ● Insert a new blade of the same length and type in the rear wiper arm in the opposite direction to the arrow and hook into place button ● Replace the wiper arm on the rear window. WARNING Worn or dirty wiper blades reduce visibility and increase the risk of acci- dent and serious injury.
Page 224: Wheels And Tyres
– Keep grease, oil and fuel off the tyres. If you wish to change or fit wheels, rims or wheel trims, we recommend that you consult with a SEAT Official Service centre for advice regarding current – Replace any missing valve caps as soon as possible.
Page 225 If you notice excessive tyre wear, you should check wheel Tyre pressure values are indicated on the inside of the fuel tank flap. alignment at a SEAT Official Service. Insufficient or excessive pressure greatly reduces the useful life of the tyres WARNING and adversely affects vehicle performance and ride.
Page 226 Wheels and tyres Indications of wear WARNING Tread wear indicators indicate if a tyre is worn. The tyres must be replaced at the latest when the tread is worn down to the tread wear indicators. Failure to do so could result in an accident. ●...
Page 227 The tyres and wheel rims are an essential part of the vehicle's design. The When replacing the tyres, it is therefore important to make sure that the tyres and rims approved by SEAT are specially matched to the characteris- actual size of the new tyres does not exceed the dimensions of the factory- tics of the vehicle and make a major contribution to good roadholding and approved makes of tyre.
Page 228 Wheels and tyres If you use tyres that are approved by SEAT you can be sure that the actual Note tyre dimensions will be correct for your vehicle. If you decide to fit a differ- ent type of tyre, you must obtain the appropriate manufacturer's certificate ●...
Page 229 4 mm. being used. It is best to contact a SEAT Official Service to check the maximum speed The performance of winter tyres is also severely impaired by ageing, even if the tread is still much deeper than 4 mm.
Page 230 Wheels and tyres Only use snow chains with fine-pitch links. The links must not protrude For the sake of the environment more than 13.5 mm from the tyres (including tensioner). Summer tyres should be fitted again as soon as possible; they give better Remove wheel covers and trim rings before fitting snow chains.
Page 231: Accessories And Modifications To The Vehicle
Your vehicle is designed to offer a high standard of active and passive safe- Unauthorised modifications to the electronic components, software, wiring ty. For this reason, we recommend that you ask a SEAT Official Service for or data transfer in the vehicle may cause malfunctioning. Due to the way the advice before fitting accessories or replacement parts.
Page 232 ● the effective transmitting power does not exceed 10 Watts at the aerial netic fields that could cause a health hazard. base. A SEAT Official Service and specialised workshop will be able to inform you Note about options for installing and operating radio transmitters with a higher transmitting power.
Page 233: Emergencies
Emergencies Emergencies General information Equipment – If you have a flat tyre or puncture, park the car as far away from Reflective vests the flow of traffic as possible in a safe place. If you have a punc- ture, stop the vehicle on a horizontal surface. If you are on a Wearing a reflective vest makes you more visible to other road slope, take extra care.
Page 234: Tyre Repair Kit
Emergencies Tyre repair kit The tyre repair kit is designed to repair your tyre provisionally only. The dam- aged tyre should be replaced as soon as possible ⇒ If the tyre has been damaged by a nail, for example, remove the nail from What to do first the tyre.
Page 235 ● Observe the expiry date stated on the sealing compound can. Have the – Remove the sealing plug from the filling hose and insert the sealing compound changed by a specialised workshop or SEAT Service. hose into the tyre valve.
Page 236: Changing A Wheel
If you change the wheel on a slope, block the wheel on the opposite side You can dispose of the used bottle of sealing compound at a SEAT Official of the car with a stone or similar to prevent the vehicle from moving.
Page 237 Emergencies Wheel covers* Removing the wheel bolt caps* The wheel covers must be removed for access to the wheel bolts Fig. 120 Wheel: wheel bolts with caps Removal – Fit the plastic clip (vehicle tools) over the cap until it clicks into ⇒ ...
Page 238 Make a note of the code number of the anti-theft wheel bolt and keep it in a safe place, but not in your vehicle. If you need a new adapter, you can ob- tain it from the SEAT Official Service, indicating the code number. ...
Page 239 Emergencies WARNING Slightly loosen the wheel bolts (one turn) before raising the vehicle with the jack*. If not, an accident may occur.  Raising the vehicle Fig. 124 Strut: mount- ing the jack on the ve- hicle – Place the jack* (vehicle tools) on a firm surface. If necessary use a large, strong board or similar support.
Page 240 Emergencies Putting on the spare wheel WARNING When fitting tyres with a compulsory rotation direction, observe ● Make sure that the jack* remains stable. If the surface is slippery or the instructions in ⇒ p age 239. soft, the jack* could slip or sink, respectively, with the resultant risk of injury.
Page 241: Spare Wheel
Have the tyres checked, and if necessary, replaced ⇒ p age 175. as soon as possible at a SEAT Official Service or at a specialised workshop. – The wheel bolts should be tightened to 120 Nm. Check the tor- que as soon as possible with a torque wrench.
Page 242: Jump Starting
Emergencies Jump starting – Take out the temporary spare wheel. Chains Jump leads For technical reasons, snow chains must not be used on the temporary spare wheel. The jump lead must have a sufficient wire cross section. If you have a puncture on one of the front wheels when using snow chains, fit the temporary spare wheel in place of one of the rear wheels.
Page 243 Emergencies How to jump start: description – Connect one end of the red jump lead to the positive termi- ⇒ F ig. nal of the vehicle with the flat battery 126. – Connect the other end of the red jump lead to the positive ter- minal in the vehicle providing assistance –...
Page 244 Emergencies Starting WARNING (Continued) 5. Start the engine of the vehicle with the boosting battery and let ● Never use jump leads when one of the batteries is frozen. Danger of it run at idling speed. explosion! Even after the battery has thawed, battery acid could leak and cause chemical burns.
Page 245: Towing And Tow-Starting The Vehicle
Emergencies Towing and tow-starting the vehicle – Ensure that the tow rope remains taut at all times. Tow rope or tow bar General information It is easier and safer to tow a vehicle with a tow bar. You should only use a tow rope if you do not have a tow bar.
Page 246 Emergencies – Take the towline anchorage out of the vehicle tool kit Note ⇒ p age 232. ● Please observe legal requirements when doing so. – Screw the towline anchorage into the screw connection as far as ● Switch on the hazard warning lights of both vehicles. However, observe ⇒ ...
Page 247 Emergencies Rear towline anchorage Vehicles with towline anchorage On the right of the rear bumper there is a cover which covers a The rear towline anchorage should only be mounted if you threaded hole. wish to tow another vehicle. – Take the towline anchorage out of the vehicle tool set ⇒ ...
Page 248 Emergencies Tow-starting Towing vehicles with a manual gearbox As a general rule, tow-starting is not recommended. Towing is relatively straightforward. Please observe the relevant instructions ⇒ p age 244. – Engage 2nd or 3rd gear before moving off. The vehicle can be towed using a tow bar or tow rope in the normal way, –...
Page 249 Emergencies Note ● If it is not possible to tow the vehicle in the normal way, or if it has to be towed further than 50 km (30 miles), it must be transported on a special car transporter or trailer. ●...
Page 250: Fuses And Bulbs
Fuses and bulbs Fuses and bulbs Electrical fuses Changing fuses A blown fuse can be identified by the blown metal strip. Fig. 132 Engine com- partment, left-hand side: fuse cover Fuses in the steering column area – Switch off the ignition and component concerned. –...
Page 251 Fuses and bulbs ⇒ F ig. Fuses in the vehicle interior – Unlock the fuse cover 132. – Remove the clips from the fuse cover. Electrical consumer Amps – Use the plastic clip to pull out the fuse and replace the blown Vacant fuse with a fuse of the same rating.
Page 252: Fuses On Left Side Of Engine
Fuses and bulbs Electrical consumer Amps Note Vacant Please note that the above list, while correct at the time of printing, is sub- Vacant ject to alterations.  Left lights Parking aid control unit Airbag Fuses on left side of engine compartment Reverse switch, clima sensor, electrochromic mirror Electrical consumer...
Page 253: Changing A Bulb
Fuses and bulbs Full-LED headlight system* Electrical consumer Amps Full-LED headlights handle all light functions (daylight, side light, turn sig- nal, dipped beam and route light) with light emitting diodes (LEDs) as a Vacant light source. Vacant Full-LED headlights are designed to last the lifetime of the car and light Vacant bulbs cannot be replaced.
Page 254 Fuses and bulbs LED rear light Type Reverse lights P21W LL The remaining functions work with LEDs WARNING ● Take particular care when working on components in the engine com- partment if the engine is warm. Risk of burns. ● Bulbs are highly sensitive to pressure. The glass can break when you touch the bulb, causing injury.
Page 255: Changing Bulbs In Headlight Unit
Fuses and bulbs ⇒ F ig. 134 Changing bulbs in headlight unit – Unclip the retainer spring pressing inwards to the right. Dipped beam bulb – Extract the bulb and fit the replacement so that the rim of the attachment plate is on the reflector cut-out. ...
Page 256 Fuses and bulbs Turn signal bulb Main beam bulb Fig. 138 Main beam Fig. 136 Turn signal bulb bulb Fig. 139 Main beam Fig. 137 Turn signal bulb bulb – Raise the bonnet – Raise the bonnet ⇒ F ig. 136 ⇒ ...
Page 257: Changing Bulb For Front Fog Light
Fuses and bulbs ⇒ F ig. 140 Changing bulb for front fog light – Remove the bolt from the fog light grille with a screwdriver. ⇒ F ig. 141 Front fog light bulb – Remove the bolts (3x) to remove the fog light. –...
Page 258: Changing Tail Light Bulbs (On Side Panel)
Fuses and bulbs Remove the bulb holder Changing tail light bulbs (on side panel) Overview of tail lights Rear lights on the side panel Turn signal PY21W NA LL Side light and brake light P21W LL  Fig. 142 Front fog light ⇒ ...
Page 259 Fuses and bulbs Removing tail light – Remove the cover by prying the flat side of a screwdriver into ⇒ F ig. 143 the recess and remove the cover from the opening – Carefully loosen the screw located behind the cover with a ⇒ ...
Page 260: Changing Tail Light Bulbs (On Rear Lid)
Fuses and bulbs Remove the bulb holder Note When changing a bulb, you must first remove the bulb hold- In the case of LED lights, change only the turn signal bulb.  Changing tail light bulbs (on rear lid) Overview of tail lights Rear lid lights Left side Side lights...
Page 261 Fuses and bulbs Remove the bulb holder – Unlock the retaining tabs of the bulb holder, following the ⇒ F ig. direction of arrows 147. The rear lid must be open to change the bulbs. – Remove the bulb holder by turning it in the direction of arrow ⇒ ...
Page 262: Changing Number Plate Light Bulbs
Fuses and bulbs Note For LED pilots, you can only change the fog or reverse bulb, on the left or right guide.  Fitting the bulb holder ⇒ F ig. 147 – Install the bulb holder making sure that locking clips are properly clipped on.
Page 263 Fuses and bulbs 7. Plug the connector into the bulb holder. ...
Page 264: Technical Specifications
Technical specifications Technical specifications Technical specifications Important Abbreviations used in the Technical Specifications section Abbrevia- Meaning The information in your vehicle's official documents always tion take precedence over the information in the current instruc- Kilowatt, engine power measurement. tion manual. Pferdestärke (horsepower), formerly used to denote engine power.
Page 265: Vehicle Identification Data
Technical specifications Vehicle identification data Vehicle data sticker The vehicle data sticker is under the carpet trim in the luggage compart- ment, in the spare wheel well. A sticker with the vehicle data is attached to the inside cover of the Maintenance Programme. ⇒ ...
Page 266: Information On Fuel Consumption
Technical specifications Information on fuel consumption Weights Kerb weight refers to the basic model with a fuel tank filled to 90% capacity Fuel consumption and without optional extras. The figure quoted includes 75 kg to allow for the weight of the driver. The consumption and emission details shown on the vehicle For special versions and optional equipment fittings or for the addition of data sticker differ from one vehicle to another.
Page 267: Wheels
Technical specifications Drawbar loads Snow chains The maximum permitted drawbar load on the ball joint of the towing bracket Snow chains may be fitted only to the front wheels, and only for the follow- must not exceed 80 kg. ing tyres: In the interest of road safety, we recommend that you always tow approach- 175/70R14 Chains with links not exceeding 15 mm (including the chain...
Page 268: Engine Specifications
Technical specifications Engine specifications Overview You will find further explanations, instructions and restrictions on the tech- nical specifications as of ⇒ p age 263.  Checking fluid levels From time to time, the levels of the different fluids in the ve- hicle must be checked.
Page 269 Technical specifications Petrol engine 1.2 63 kW (85 PS) Engine specifications Power output in kW (PS) 63 (85)/ 4300-5300 Maximum torque in Nm at rpm 160/ 1400-3500 No. of cylinders/capacity in cm 4/ 1197 Fuel Super 95 RON Research Octane Number = Anti-detonation rating of the petrol. Performance Maximum speed in km/h (mph)
Page 270 Technical specifications Petrol engine 1.2 77 kW (105 PS) Engine specifications Power output in kW (PS) 77 (105)/ 4500-5500 Maximum torque in Nm at rpm 175/ 1400-4000 No. of cylinders/capacity in cm 4/ 1197 Fuel Super 95 RON Research Octane Number = Anti-detonation rating of the petrol. Performance Manual Start-Stop...
Page 271 Technical specifications Petrol engine 1.4 90 kW (122 PS) Start-Stop Engine specifications Power output in kW (PS) 90 (122)/ 5000-6000 Maximum torque in Nm at rpm 200/ 1400-4000 No. of cylinders/capacity in cm 4/ 1395 Fuel Super 95 RON Research Octane Number = Anti-detonation rating of the petrol. Performance Maximum speed in km/h (mph)
Page 272 Technical specifications Petrol engine 1.4 103 kW (140 PS) Start-Stop Engine specifications Power output in kW (PS) 103 (140)/ 5000 Maximum torque in Nm at rpm 250/ 1500-3500 No. of cylinders/capacity in cm 4/ 1395 Fuel Super 95 RON /Normal 91 RON Research Octane Number = Anti-detonation rating of the petrol.
Page 273 Technical specifications Petrol engine 1.8 132 kW (180 PS) Start-Stop Engine specifications Power output in kW (PS) 132 / 5100-6200 Maximum torque in Nm at rpm 250/ 1250-3900 No. of cylinders/capacity in cm 4/ 1798 Fuel Super 95 RON Research Octane Number = Anti-detonation rating of the petrol. Performance Manual Automatic...
Page 274 Technical specifications Diesel engine 1.6 66 kW (90 PS) Engine specifications Power output in kW (PS) 66 (90) /2750-4800 Maximum torque in Nm at rpm 230/1400-2750 No. of cylinders/capacity in cm 4/1598 Fuel Diesel according to standard EN 590, Min. 51 CN Performance Maximum speed in km/h (mph)
Page 275 Technical specifications Diesel engine 1.6 77 kW (105 PS) Engine specifications Power output in kW (PS) 77 (105) /3000-4000 Maximum torque in Nm at rpm 250/1500-2750 No. of cylinders/capacity in cm 4/1598 Fuel Diesel according to standard EN 590, Min. 51 CN Performance Manual Start-Stop...
Page 276 Technical specifications Diesel engine 2.0 110 kW (150 PS) Engine specifications Power output in kW (PS) 110 (150) /3500-4000 Maximum torque in Nm at rpm 320/1750-3000 No. of cylinders/capacity in cm 4/1968 Fuel Diesel according to standard EN 590, Min. 51 CN Performance Manual Start-Stop...
Page 277: Dimensions And Capacities
Technical specifications Dimensions and capacities Dimensions Length, width 4263 mm/1816 mm Height at kerb weight 1459 mm Front and rear projection 853 mm/774 mm Wheelbase 2636 mm Turning circle 10.9 m Front Rear Track width 1533 mm 1504 mm 1549 mm 1520 mm Capacities Fuel tank...
Page 278: Index
Index Index Anti-dazzle rear vision mirrors Automatic gearbox ..... . 154 ........123 Backup programme .
Page 279 Rims ......201 Changing main headlight Seat belts ......205 Braking main beam .
Page 280 Convenience closing senger seat ......31 With a trailer ....194, 195 Panoramic sliding sunroof .
Page 281 Index Emergency locking and unlocking ..96 Environmental tip Faulty bulbs Leaks ......210 Changing a bulb .
Page 282 Index Gearshift paddles (automatic gearbox) ..159 Increase capacity of luggage compartment ....132 General overview of the engine compartment 267 Indicator Glass Driver messages (mechanical contact) .
Page 283 Index Leather Care Longlife inspection service ....211 Multi-collision Brake ....184 Natural leather .
Page 284 Index Outside temperature ..... 64 Passenger Remote control key see Correct sitting position ..11, 12, 13 Unlocking/Locking .
Page 285 See "Lamps" ......69 Seat belts ......19 Snow chains .
Page 286 Vehicle identification data ... . . 264 The danger of not using the seat belt ..22 Tyre monitoring indicator ....177 Vehicle battery Tightening torque of wheel bolts .
Page 287 Heated windscreen washer jets ..119 Why wear seat belts? ....19, 21, 30 Salt on the roads ....121 Windows Winter tyres .
Page 288 SEAT S.A. is permanently concerned about continuous development of its types and models. For this reason we ask you to under- stand, that at any given time, changes regarding shape, equipment and technique may take place on the car delivered. For this reason no right at all may derive based on the data, drawings and descriptions in this current handbook.

This manual is also suitable for:

Leon se370 2012

Seat Leon Owner's Manual

Manual Structure

Content

Safety First

Operating Instructions

Practical Tips

Technical Specifications

Index

Quick Links

Need help?

Questions and answers

Related Manuals for Seat Leon

Summary of Contents for Seat Leon

This manual is also suitable for:

Table of Contents