Advertisement
DURA-GLAS
Sta-Rite Pool/Spa Group
293 Wright Street, Delavan, WI 53115
North America: 800-752-0183, FAX 800-582-2217
International: 414-728-5551, FAX: 414-728-4461, TELEX: ITT 4970245
Oxnard, CA • Union City, TN • Delavan, WI • Mississauga, Ont.
© 1996, Sta-Rite Industries, Inc. Printed in U.S.A.
CENTRIFUGAL PUMPS
TM
WITH INTEGRAL TRAP
O
W
N
E
R '
INSTALLATION, OPERATION & PARTS
P2R and P2RA Series MODELS
HP
1/2
–
3/4
P2R52D3-124
1
P2R52E3-125
1-1/2
P2R52F3-126
2
P2R52G3-122
2-1/2
–
S
M
A
N
P2R Series
U
A
L
P2RA Series
P2RA52C3-119
P2RA52D3-120
P2RA52E3-124
P2RA52F3-125
P2RA52G3-126
P2RAA52G3-122
This manual should be furnished to
the end user of this pump; its use
will reduce service calls and chance
of injury and will lengthen pump life.
S138 (Rev. 11/18/96)
Advertisement
Table of Contents
Related Manuals for STA-RITE DURA-GLAS
Summary of Contents for STA-RITE DURA-GLAS
- Page 1 293 Wright Street, Delavan, WI 53115 North America: 800-752-0183, FAX 800-582-2217 International: 414-728-5551, FAX: 414-728-4461, TELEX: ITT 4970245 Oxnard, CA • Union City, TN • Delavan, WI • Mississauga, Ont. S138 (Rev. 11/18/96) © 1996, Sta-Rite Industries, Inc. Printed in U.S.A.
-
Page 2: Table Of Contents
To avoid unneeded service calls, prevent possible injuries, and get the most out of your pump, READ THIS MANUAL CAREFULLY! The Sta-Rite ‘P2R’ and ‘P2RA’ Series Self-priming Centrifugal pump: • Is designed for use with swimming pools or as a centrifugal pump. -
Page 3: Safety Instructions
Check all clamps, bolts, lids, and system accessories before testing. Release all air in system before testing. Tighten Sta-Rite trap lids to 30 ft. lbs. (4.1 kg-m) torque for testing. Water pressure for test must be less than 25 PSI (7.5 kg/cm Water Temperature for test must be less than 100 F. -
Page 4: Installation
FIGURE 1 INSTALLATION Only qualified, licensed personnel should install pump and wiring. Pump mount must: Be solid - Level - Rigid - Vibration free. (To reduce vibration and pipe stress, bolt pump to mount.) Allow pump suction inlet height to be as close to water level as possible. Allow use of short, direct suction pipe (To reduce friction losses). - Page 5 Piping: Use at least 1-1/2" IPS PVC pipe with 5” trap. Use at least 2” pipe with 6” trap. Increase size if a long run is needed. To avoid strains on the pump, support both suction and discharge pipes independently. Place these supports near the pump. To avoid a strain left by a gap at the last connection, start all piping at the pump and run pipe away from the pump.
-
Page 6: Electrical
ELECTRICAL Ground motor before connecting to electrical power supply. Failure to ground motor can cause severe or fatal electrical shock hazard. Do not ground to a gas supply line. To avoid dangerous or fatal electrical shock, turn OFF power to motor before working on electrical connections. -
Page 7: Operation
OPERA TION NEVER run pump dry! Running pump dry may damage seals, causing leakage and flooding! Fill pump with water before starting motor. Before removing trap cover: 1. STOP PUMP before proceeding. 2. CLOSE GATE VALVES in suction and discharge pipes. 3. -
Page 8: Pump Service
3. Remove trap cover and use low pressure (5 PSI or less) air to blow accu- mulated water from the piping system. Use a Sta-Rite U79-11 Lid Wrench to remove trap covers that have been overtightened or have taken a set and cannot be removed by hand. - Page 9 2. Be sure there is no pressure in trap body; remove cover (unscrew by turn- ing counterclockwise). 3. Remove clamp holding pump halves together. 4. Remove pump base mounting bolts, if used. Motor and seal plate assem- bly can now be pulled away from pump body. 5.
-
Page 10: Troubleshooting Guide
TROUBLESHOOTING GUIDE Read and understand safety and operating instructions in this manual before doing any work on pump! Only qualified personnel should electrically test pump motor! FAILURE TO PUMP; REDUCED CAPACITY OR DISCHARGE PRESSURE Suction leaks/lost prime: 1. Pump must be primed; make sure that pump volute and trap are full of water. -
Page 11: Repair Parts List
REPAIR PARTS LIST P2R SERIES DURA-GLAS POOL PUMP ® 3/4 through 2 H.P. Models Part Part Description Qty. Motor Chart at Right Screw #10-32 x 1/2” U30-856ZP 1831 0695 Bonding Lug U17-568 Water Slinger C69-2 Seal Plate C203-137P1 O-Ring U9-228A... - Page 12 REPAIR PARTS LIST P2RA SERIES DURA-GLAS POOL PUMP ® 1/2 through 2-1/2 H.P. Models Part Part Description Qty. Motor Chart at Right Screw #10-32 x 1/2” U30-856ZP Bonding Lug U17-568 1831 0695 Water Slinger C69-2 Seal Plate* C203-137P1 O-Ring U9-228A...
- Page 13 5” TRAP/ADAPTER ASSEMBLY PKG. 115 REPAIR PARTS LIST - 5” and 6” TRAPS* Part No. Part Pkg. 115 Pkg. 161 Description 5” Trap 6” Trap Trap Cover C3-139P1 16920-0011 O-Ring - Cover U9-229 16920-0012 Strainer Basket C108-33P 16920-0017 Trap Body C153-53P1 C153-58P Gasket...
-
Page 14: Warranty
Retain Warranty Certificate (upper portion) in a safe and convenient location for your records. DETACH HERE: Fill out bottom portion completely and mail within 10 days of purchase/installation to: Sta-Rite, Attn: Warranty Dept., 293 Wright St., Delavan, WI 53115 Warranty Registration Card...
Need help?
Do you have a question about the DURA-GLAS and is the answer not in the manual?
Questions and answers