Page 1 Upgrade and Maintenance Manual - English FUJITSU Server PRIMERGY TX1320 M1 Upgrade and Maintenance Manual Edition August 2014...
Page 2: Copyright And Trademarks
– The contents of this manual may be revised without prior notice. – Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. – No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.
Page 3 Before reading this manual For your safety This manual contains important information for safely and correctly using this product. Carefully read the manual before using this product. Pay particular attention to the accompanying manual "Safety Notes and Regulations" and ensure these safety notes are understood before using the product.
Page 4 Please consult the sales staff of Fujitsu if intending to use this product for high safety use. Measures against momentary voltage drop This product may be affected by a momentary voltage drop in the power supply caused by lightning.
Page 5 Only for the Japanese market: Although described in this manual, some sections do not apply to the Japanese market. These options and routines include: – CSS (Customer Self Service) – USB Flash Module (UFM) Upgrade and Maintenance Manual TX1320 M1...
Page 6: Version History
Version History Version History Issue number Reason for update 1.0 / August 2014 Initial release Upgrade and Maintenance Manual TX1320 M1...
Page 7: Table Of Contents
Contents Version History ....... 6 Introduction ......19 Notational conventions .
Page 8 Contents 4.1.3.2 Local diagnostic indicators on the system board ..49 Shutting down the server ....52 Opening the server .
Page 9 Contents 5.2.2 Verifying system information backup / restore ..86 5.2.3 Updating RAID controller firmware ....87 5.2.4 Enabling Option ROM scan .
Page 10 Contents Hard disk drives / solid state drives ... . . 115 Basic procedure ......116 2.5-inch hard disk drives / solid state drives .
Page 11 Contents 7.4.1.3 Removing the 2.5-inch HDD SAS / SATA backplane ..143 7.4.1.4 Installing the 2.5-inch HDD SAS / SATA backplane ..145 7.4.1.5 Installing the air duct (if applicable) ... . . 147 7.4.1.6 Concluding steps .
Page 12 Contents 9.2.1.4 Connecting cables to the expansion card ..177 9.2.1.5 Concluding steps ..... . 177 9.2.2 Removing expansion cards .
Page 13 Contents 9.4.1.3 Network adapter D2745 ....203 9.4.1.4 Network adapter D2755 ....205 9.4.2 Handling SFP+ transceiver modules .
Page 14 Contents 11.3 Replacing the processor heat sink ....234 11.3.1 Preliminary steps ......234 11.3.2 Replacing the processor heat sink .
Page 15 Contents 12.4.1.1 Preliminary steps ..... . . 263 12.4.1.2 Removing the backup drive filler cover ... 264 12.4.1.3 Installing the HDD expansion box .
Page 16 Contents 14.3.2.3 Concluding steps ..... . 289 14.3.3 Replacing the UFM ..... . . 290 14.3.3.1 Preliminary steps .
Page 17 Contents 16.1.3 Server interior ......323 16.2 Configuration tables ..... . 324 16.2.1 Mounting order for Hard disk drives / solid state drives .
Page 18 Contents Upgrade and Maintenance Manual TX1320 M1...
Page 19: Introduction
Introduction This Upgrade and Maintenance Manual provides instructions for the following procedures: Upgrading the server configuration by adding optional hardware ● components Upgrading the server configuration by replacing existing hardware ● components with superior ones. Replacing defective hardware components ● This manual focuses on on-site maintenance tasks.
Page 20: Notational Conventions
Introduction Notational conventions The following notational conventions are used in this manual: indicates commands or menu items Text in italics indicates system output fixed font indicates text to be entered by the user semi-bold fixed font "Quotation marks" indicate names of chapters and terms that are being emphasized describes activities that must be performed in the order Ê...
Page 21: Before You Start
Japanese market: http://jp.fujitsu.com/platform/server/primergy/system/ Please contact your local Fujitsu customer service partner for details on how to order expansion kits or spare parts. Use the Fujitsu Illustrated Spares Catalog to identify the required spare part and obtain technical data and order information.
Page 22 For further information, refer to the "ServerView Suite Local Service Concept (LSC)" manual available online at (EMEA market) or http://manuals.ts.fujitsu.com http://jp.fujitsu.com/platform/server/primergy/manual/ (Japanese market). It is recommended to prepare local maintenance tasks using remote diagnostics procedures, as described in the "ServerView Suite Local Service Concept...
Page 23: Classification Of Procedures
At the beginning of each procedure, the involved unit type is indicated by one of the symbols introduced in this section. Please ask your local Fujitsu service center for more detailed information. 2.1.1 Customer Replaceable Units (CRU)
Page 24: Upgrade And Repair Units (Uru)
Before you start 2.1.2 Upgrade and Repair Units (URU) Upgrade and Repair Units (URU) Upgrade and Repair Units are non hot-plug components that can be ordered separately to be installed as options (Upgrade Units) or are available to the customer through customer self service (Repair Units). Server management error messages and diagnostic indicators on the front panel and system board will report defective Upgrade and Repair Units as customer replaceable CSS components.
Page 25: Field Replaceable Units (Fru)
Maintenance procedures involving Field Replaceable Units must be performed exclusively by Fujitsu service personnel or technicians trained by Fujitsu. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. Components that are handled as Field Replaceable Units –...
Page 26: Average Task Duration
Before you start Average task duration Average task duration: 10 minutes The average task duration including preliminary and concluding steps is indicated at the beginning of each procedure next to the procedure class. Refer to table 1 on page 26 for an overview of steps taken into account for calculating the average task duration: Step...
Page 27: Tools You Need At Hand
Before you start Tools you need at hand When preparing the maintenance task, ensure that all required tools are available according to the overview below. You will find a list of required tools at the beginning of each procedure. Screw driver / Screw Usage Type...
Page 28: Documents You Need At Hand
"Quick Start Hardware - PRIMERGY Server TX1320 M1" leaflet Quick installation poster for initial operation, " はじめにお読みください - available only in printed form PRIMERGY TX1320 M1 " リーフレット for the Japanese market "Safety notes and regulations" manual Important safety information, available online or as a printed copy "...
Page 29 Before you start Document Description "FUJITSU Server PRIMERGY available online TX1320 M1 Operating Manual" "D3239 BIOS Setup Utility for FUJITSU Server PRIMERGY Information on configurable BIOS options TX1320 M1 S3 Reference and parameters, available online Manual" Labels inside the side / top cover outlining...
Page 30 Before you start Document Description RAID documentation, online at under x86 Servers http://manuals.ts.fujitsu.com - Expansion Cards - Storage Adapters. Additional documentation For the Japanese market please use the following address: http://jp.fujitsu.com/platform/server/primergy/ manual/ – Operating system documentation, online help Third party documentation –...
Page 31: Important Information
Important information CAUTION! Before installing and starting up a device, please observe the safety instructions listed in the following section. This will help you to avoid making serious errors that could impair your health, damage the device and endanger the data base. Keep all manuals and the other documentation (such as the technical manual, documentation DVD) close to the device.
Page 32 Important information If the device is brought in from a cold environment, condensation may form ● both inside and on the outside of the device. Wait until the device has acclimatized to room temperature and is absolutely dry before starting it up. Material damage may be caused to the device if this requirement is not observed.
Page 33 Important information Ethernet cabling has to comply with EN 50173 and EN 50174-1/2 standards ● or ISO/IEC 11801 standard respectively. The minimum requirement is a Category 5 shielded cable for 10/100 Ethernet, or a Category 5e cable for Gigabit Ethernet. Route the cables in such a way that they do not create a potential hazard ●...
Page 34 Important information Do not damage or modify internal cables or devices. Doing so may cause a ● device failure, fire, or electric shock and will void the warranty and exempt the manufacturer from all liability. Devices inside the server remain hot after shutdown. Wait for a while after ●...
Page 35 Important information Batteries Incorrect replacement of batteries may lead to a risk of explosion. The ● batteries may only be replaced with identical batteries or with a type recommended by the manufacturer. Do not throw batteries into the trash can. ●...
Page 36 Important information High humidity and airborne dust levels are to be avoided. Electric ● shocks and/or server failures may be caused by liquids such as water, or metallic items, such as paper clips, entering a drive. Shocks and vibrations are also to be avoided. ●...
Page 37 Important information You can prevent damage from the optical disk drive and the CDs/DVDs/BDs, as well as premature wear of the disks, by observing the following suggestions: – Only insert disks in the drive when needed and remove them after use.
Page 38: Ce Conformity
Important information The circuit boards and soldered parts of internal options are exposed and ● can be damaged by static electricity. To ensure reliable protection, you must wear an earthing band on your wrist when working with this type of module and connect it to an unpainted, conducting metal part of the system.
Page 39: Fcc Class A Compliance Statement
Consult the dealer or an experienced radio/TV technician for help. ● Fujitsu is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.
Page 40: Environmental Protection
Important information Environmental protection Environmentally-friendly product design and development This product has been designed in accordance with the Fujitsu standard for "environmentally friendly product design and development". This means that key factors such as durability, selection and labeling of materials, emissions, packaging, ease of dismantling and recycling have been taken into account.
Page 41 Details regarding the return and recycling of devices and consumables within Europe can also be found in the "Returning used devices" manual, via your local Fujitsu branch or from our recycling center in Paderborn: Fujitsu Technology Solutions Recycling Center D-33106 Paderborn Tel.
Page 42 Important information Upgrade and Maintenance Manual TX1320 M1...
Page 43: Basic Hardware Procedures
The "FUJITSU Server PRIMERGY TX1320 M1 Operating manual" gives an introduction to server features and provides an overview of available hardware options. Use the Fujitsu ServerView Suite management software to plan the upgrade or replacement of hardware components. ServerView Suite documentation is available online at (EMEA market) or http://manuals.ts.fujitsu.com...
Page 44: Locating The Defective Server
Basic hardware procedures 4.1.1 Locating the defective server Figure 2: Identification button and indicator on front panel Figure 3: Indicators on the connector panel: CSS, Global Error and ID indicators 1 CSS, Global Error and ID indicators (yellow, orange and blue) When working in a datacenter environment, switch on the ID indicator on the front and rear connector panels of the server for easy identification.
Page 45: Determining The Error Class
Manager user interface to switch on the system identification LEDs (2). For further information, refer to the "ServerView Suite Local Service Concept (LSC)" manual available from the ServerView Suite DVD supplied with your PRIMERGY server or online at http://manuals.ts.fujitsu.com (EMEA market) or http://jp.fujitsu.com/platform/server/primergy/manual/ (Japanese market).
Page 46: Global Error Indicator
Basic hardware procedures 4.1.2.1 Global Error indicator Figure 4: Global Error indicator on front panel Ê Check the Global Error indicator (1) on the front or connector panel of the server: Indicator Status Description no critical event (non CSS component) prefailure detected (non CSS component), Global error orange on...
Page 47: Customer Self Service (Css) Indicator
PSU modules allow you to identify the defective component. For further information, refer to the "ServerView Suite Local Service Concept (LSC)" manual available from the ServerView Suite DVD supplied with your PRIMERGY server or online at http://manuals.ts.fujitsu.com (EMEA market) or (Japanese market). http://jp.fujitsu.com/platform/server/primergy/manual/...
Page 48: Local Diagnostic Indicators On The Front
Basic hardware procedures 4.1.3.1 Local diagnostic indicators on the front Figure 6: Local diagnostic indicators on front panel Ê Check the local diagnosis indicator lamp (1) - (6) at the front of the server: Indicator Status Description HDD error HDD / SSD, SAS / SATA backplane or yellow on indicator RAID controller failure detected...
Page 49: Local Diagnostic Indicators On The System Board
Basic hardware procedures 4.1.3.2 Local diagnostic indicators on the system board FAN4SYS DIMM1B DIMM2B COM1 DIMM1A DIMM2A SATA POWER Service Management LAN/ USB 9/10 Intel FAN1 Shared LAN/ i210 USB 7/8 Standard LAN/ Intel USB 5/6 i217 FAN2SYS SATA1-4 Micro Slot 4 PCIe x8 Indicate USB1AUX...
Page 50 Basic hardware procedures Ê Remove the server cover as described in section "Opening the server" on page Ê Press the Indicate CSS button (1) to highlight defective components. Component LEDs LEDs A, B and C are visible from the outside on the server rear. All other LEDs are only visible if the server cover has been opened.
Page 51 Basic hardware procedures Indicator Status Description green iRMC S4 management controller is iRMC flashing operational In addition to local diagnostic indicators, CSS or Global Error LEDs indicate, if the defective component is a customer replaceable unit or if a service technician needs to be dispatched to replace the part (see section "Determining the error class"...
Page 52: Shutting Down The Server
Basic hardware procedures Shutting down the server CAUTION! For further safety information, please refer to chapter "Important information" on page This step is only required when upgrading or replacing non-hot plug components. Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality"...
Page 53 Basic hardware procedures Disconnecting power cords Figure 9: Removing the power cord from the PSU cable tie Ê Pull out on the locking lever on the PSU cable tie(s) (1) and loosen the loop (2). Ê Disconnect the power cord from the PSU module and remove it from the cable tie.
Page 54 Basic hardware procedures Removing security cover Figure 10: Removing the security cover Ê Insert the key (1). Ê While pressing the key on the screw turn the key counter-clockwise and remove the screw. Ê Remove the security cover (2). Upgrade and Maintenance Manual TX1320 M1...
Page 55: Opening The Server
In order to comply with applicable EMC regulations (regulations on ● electromagnetic compatibility) and satisfy cooling requirements, the PRIMERGY TX1320 M1 server must not run while the side cover is removed. For further safety information, please refer to chapter "Important ●...
Page 56: Removing The Server Cover
Basic hardware procedures 4.3.1 Removing the server cover Figure 11: Open the lock Ê Turn the key clockwise to unlock the sever cover. Upgrade and Maintenance Manual TX1320 M1...
Page 57 Basic hardware procedures Figure 12: Unlocking the locking bar Ê Slide the locking bar to the left until it rests in place. Figure 13: Removing the server cover Ê Push the server cover to the front. Ê Remove the server cover. Upgrade and Maintenance Manual TX1320 M1...
Page 58: Removing The Drive Cover
Basic hardware procedures 4.3.2 Removing the drive cover Figure 14: Opening the drive cover Ê Turn the key clockwise (1). Depending on the setting of the green hook in the drive cover, you can open the drive cover without turning the key or only with turning the key (For further information, please refer to the Operating Manual section "opening the drive cover").
Page 59: Removing The Hard Disk Drive Cover
Basic hardware procedures 4.3.3 Removing the hard disk drive cover Figure 15: Opening the hard disk drive cover Ê Turn the key clockwise. Ê Remove the key. Ê Open the hard disk drive cover in the direction of the arrow (1). Ê...
Page 60: Opening The Front Cage
Basic hardware procedures Opening the front cage 4.4.1 3.5-inch hard disk drive version Figure 16: Opening the front cage Ê Loosen the captive knurled thumb screw on the front cage (1). Ê Remove the HDD fan cable from the system board (2). Ê...
Page 61: Inch Hard Disk Drive Version
Basic hardware procedures 4.4.2 2.5-inch Hard disk drive version Figure 17: Opening the front cage Ê Loosen the two captive knurled thumb screws on the front cage (1). Ê Remove the HDD fan cable from the system board (2). Ê Remove the SATA cable from the system board. Ê...
Page 62: Closing The Front Cage
Basic hardware procedures Closing the front cage 4.5.1 3.5-inch hard disk drive version Figure 18: Closing the front cage Ê Carefully close the front cage (1). CAUTION! Ensure that none of the cables are strained or trapped! Ê Connect all loose cables to the system board again. Ê...
Page 63: Inch Hard Disk Drive Version
Basic hardware procedures 4.5.2 2.5-inch Hard disk drive version Figure 19: Closing the front cage Ê Carefully close the front cage (1). CAUTION! Ensure that none of the cables are strained or trapped! Ê Tighten the two captive knurled thumb screws on the front cage. Ê...
Page 64: Closing The Server
In order to comply with applicable EMC regulations (regulations on ● electromagnetic compatibility) and satisfy cooling requirements, the PRIMERGY TX1320 M1 server must not run while the side cover is removed. For further safety information, please refer to chapter "Important ●...
Page 65: Mounting The Drive Cover
Basic hardware procedures 4.6.2 Mounting the drive cover Figure 21: Installing drive cover Ê Insert the drive cover to the upper side of the side / top cover (1). Ê Close the drive cover (2). Ê Turn the key anticlockwise (3). Depending on the setting of the green hook in the drive cover, you must turning the key or not (For further information, please refer to the Operating Manual section "opening the drive cover").
Page 66: Mounting The Server Cover
Basic hardware procedures 4.6.3 Mounting the server cover Figure 22: Mounting the server cover Ê Fit the server cover on the chassis, aligning it according to the edge guide markings on the lower server surface. Upgrade and Maintenance Manual TX1320 M1...
Page 67: Connecting The Server To The Mains
Figure 23: closing the server cover Ê Slide the server cover shut by engaging the locking mechanism. Connecting the server to the mains The PRIMERGY TX1320 M1 server is equipped with a standard power supply unit. CAUTION! The power supply automatically adjusts to any mains voltage in the range of 100 V - 240 V.
Page 68 Basic hardware procedures Securing power cords Figure 24: Securing power cord Ê Connect the power cord to the power supply (1). Ê Thread the cable tie through the eye. Ê Pull the cable tie tight to secure the power cable (2). The insulated connector cannot now be disconnected from the server accidentally.
Page 69: Installing The Security Cover
Basic hardware procedures Installing the security cover The PRIMERGY TX1320 M1 can be equipped with an optional security cover. Figure 25: Rear side of the server Ê Connect the data cables to the connectors of the external connector panel (1).
Page 70 Basic hardware procedures Figure 26: Installing the security cover Ê Route the cables through the security cover (1). Ê Insert the screw. Ê Insert the key. Ê While pressing the screw turn it clockwise and fasten the security cover (2). Upgrade and Maintenance Manual TX1320 M1...
Page 71: Switching On The Server
● In order to comply with applicable EMC regulations (regulations on electromagnetic compatibility) and satisfy cooling requirements, the PRIMERGY TX1320 M1 server must not run while the server cover is removed. Follow the safety instructions in chapter "Important information" on ●...
Page 72: Concluding Software Tasks
Basic hardware procedures 4.10 Concluding software tasks Ê Perform the following software tasks to put the server back in operation: – "Resetting the boot retry counter" on page 90 – "Verifying the system time settings" on page 95 – "Viewing and clearing the System Event Log (SEL)" on page 96 –...
Page 73: Basic Software Procedures
Basic software procedures Starting the maintenance task 5.1.1 Disabling BitLocker functionality BitLocker Drive Encryption provides protection for operating system and data drives by encrypting the contents and requiring users to authenticate their credentials to access the information. On the operating system drive, BitLocker uses the compatible Trusted Platform Module (TPM) to detect if the computer's startup process has been modified from its original state.
Page 74: Disabling Svom Boot Watchdog Functionality
BitLocker setup wizard, modify the BitLocker Group Policy settings. For further information on how to disable BitLocker drive encryption, please refer to the Microsoft Knowledge Base. Fujitsu service partners will find additional information (also available in Japanese) on the Fujitsu Extranet web pages. 5.1.2...
Page 75: Configuring Boot Watchdog Settings
Basic software procedures Ê Under Watchdog Settings, you can obtain detailed information about the current watchdog status, time out intervals and actions that are triggered if watchdog time outs are exceeded. For detailed information on iRMC settings, refer to the "Integrated Remote Management Controller"...
Page 76 Basic software procedures Configuring boot watchdog settings using the iRMC web frontend Ê Enter the ServerView iRMC web frontend. Ê Select the Server Management menu. Ê Under Watchdog Settings select Continue from the Boot Watchdog drop down list. Ê Click Apply for the changes to take effect. For detailed information on iRMC settings, refer to the "Integrated Remote Management Controller"...
Page 77: Removing Backup And Optical Disk Media
For further information on "forcible" tape ejection, please refer to the "Tape Facts" guide available to Fujitsu service partners from the following https address: https://partners.ts.fujitsu.com/com/service/ps/Servers/PRIMERGY/Pages/ TapeFacts.aspx...
Page 78: Configuring Lan Teaming
Using Update Manager Express Ê If performing an offline BIOS / firmware update, first of all prepare the ServerView Update DVD or USB stick: Ê Download the latest ServerView Update DVD image from Fujitsu: for the EMEA market ftp://ftp.ts.fujitsu.com/images/serverview for the Japanese market: http://jp.fujitsu.com/platform/server/primergy/products/note/svsdvd/dvd/...
Page 79 Basic software procedures Ê In order to create a bootable USB stick, please proceed as described in the "Local System Update for PRIMERGY Servers" user guide. Ê Before using the ServerView Update DVD or USB stick in an offline environment, properly shut down the server and disconnect all external I/O connections (like LAN or FC cables) from the system.
Page 80 Basic software procedures Using PrimeCollect To start PrimeCollect, proceed as follows: Ê Before using PrimeCollect in an offline environment, properly shut down the server and disconnect all external I/O connections (like LAN or FC cables) from the system. Only keep mouse, keyboard, video cable and AC power cord connected.
Page 81: Switching On The Id Indicator
Basic software procedures 5.1.7 Switching on the ID indicator When working in a datacenter environment, switch on the ID indicator on the front and rear connector panels of the server for easy identification. For further information, refer to section "Locating the defective server" on page 44 or to the "ServerView Suite Local Service Concept (LSC)"...
Page 82: Completing The Maintenance Task
(EMEA market) http://ts.fujitsu.com/support/ http://jp.fujitsu.com/platform/server/primergy/downloads/ (Japanese market) Fujitsu does not assume responsibility for any damage done to the server or for the loss of any data resulting from BIOS updates. 5.2.1.1 Updating or recovering the system board BIOS BIOS flash procedure For the Japanese market, follow the instructions provided separately.
Page 83 Basic software procedures Ê After completion of the flash process, remove the USB stick and restart the server. BIOS recovery procedure For the Japanese market, follow the instructions provided separately. Ê Prepare a USB stick with the following files: – Update tool –...
Page 84: Updating Or Recovering The Irmc
Basic software procedures Ê Disable BIOS recovery mode using the onboard jumpers: For detailed information on jumper settings, refer to section "Onboard settings" on page 327 or the "System Board D3239 Technical Manual". Ê Close the side / top cover as described in section "Closing the server"...
Page 85 Ê Press the Power On / Off button. The system starts the POST process. In iRMC recovery mode, the “FUJITSU” logo does not show up. Ê The system will detect the USB stick.
Page 86: Verifying System Information Backup / Restore
EPROM has been restored to the system board: Chassis IDPROM: Restore successful After replacing the Chassis ID EPROM In case of the PRIMERGY TX1320 M1 server, the Chassis ID EPROM is integrated on the front panel board. Ê Check the SEL log files as described in section "Viewing and clearing the...
Page 87: Updating Raid Controller Firmware
"Local System Update for PRIMERGY Servers" user guide Using the flash tool The latest firmware files are available as ASPs (Autonomous Support Packages) for Windows or as DOS tools from the Fujitsu support web pages at: (EMEA market) http://ts.fujitsu.com/support/ http://jp.fujitsu.com/platform/server/primergy/downloads/ (Japanese market) Ê...
Page 88: Enabling Option Rom Scan
Basic software procedures 5.2.4 Enabling Option ROM scan In order to configure an expansion card that has been installed or replaced, the card’s Option ROM has to be enabled in the system board BIOS. The card’s firmware is called by the system BIOS upon reboot and can be entered and configured.
Page 89: Verifying And Configuring The Backup Software Solution
Procedures may differ depending on the backup software. For details, refer to the dedicated documentation provided separately. Further information on suitable backup software solutions and related documentation is available to Fujitsu service partners from the Fujitsu Extranet pages. Re-enabling backup drives...
Page 90: Resetting The Boot Retry Counter
Basic software procedures 5.2.6 Resetting the boot retry counter The boot retry counter is decremented from its preset value every time the POST watchdog initiates a system reboot. When the value has reached ’0’, the system will shut down and power off. 5.2.6.1 Viewing the boot retry counter The current boot retry counter status is available in the BIOS:...
Page 91 Basic software procedures Resetting the boot retry counter using the ServerView Operations Manager Ê In the ServerView Operations Manager Administration view, select Server Configuration. Ê If more than one server is managed in SVOM, select the target server and click Next. Ê...
Page 92: Enabling Svom Boot Watchdog Functionality
Basic software procedures 5.2.7 Enabling SVOM boot watchdog functionality If ServerView Operations Manager boot watchdog functionality has been disabled for firmware upgrade purposes (see section 5.1.2 on page 74), it has to be re-enabled to complete the maintenance task. Timer settings can be configured in the BIOS or using the ServerView iRMC web frontend: Configuring boot watchdog settings in the BIOS Ê...
Page 93 Basic software procedures Ê Select the Advanced menu. Ê Select the status menu of the desired component: – Processors: CPU Status This option is only available for multi-processor systems. – Memory: Memory Status – Expansion cards: PCI Status Ê Reset replaced components to Enable. Ê...
Page 94: Verifying The Memory Mode
Basic software procedures 5.2.9 Verifying the memory mode If a memory module fails, the server will reboot and the defective module will be disabled. As a result, the current operation mode (e.g. Mirrored Channel mode) may no longer be available due to a lack of identical memory module pairs. In this case, the operation mode will automatically revert to Independent Channel Mode.
Page 95: Verifying The System Time Settings
Basic software procedures 5.2.10 Verifying the system time settings This task only applies to Linux environments. After the system board has been replaced, the system time is set automatically. By default, the RTC (Real Time Clock) time standard is set as the local time. If a Linux OS is used and the hardware clock has been configured as UTC (Universal Time, Coordinated) in the operating system, the BMC local time may not be mapped correctly.
Page 96: Viewing And Clearing The System Event Log (Sel)
Basic software procedures 5.2.11 Viewing and clearing the System Event Log (SEL) 5.2.11.1 Viewing the SEL You can view the System Event Log (SEL) using the ServerView Operations Manager or the ServerView iRMC web frontend: Viewing the SEL in ServerView Operations Manager Ê...
Page 97: Clearing The Sel
Basic software procedures Viewing the SEL using the iRMC web frontend Ê Enter the ServerView iRMC web frontend. Ê Select the Event Log and choose the Internal Event Log submenu. Ê Under Internal Event Log Content the SEL is being displayed. In order to filter the list, select the check boxes next to the desired event types and press Apply for the changes to take effect.
Page 98 Basic software procedures Procedures may differ depending on your Linux OS or the definition file on the client system. Use the following information as reference. Ask the system administrator to change the definition file. Ê After replacing a network controller or the system board, switch on and boot the server as described in section "Switching on the server"...
Page 99: Enabling Bitlocker Functionality
Ê Follow the instructions in the BitLocker Setup wizard. For further information on how to enable BitLocker drive encryption, please refer to the Microsoft Knowledge Base. Fujitsu service partners will find additional information (also available in Japanese) on the Fujitsu Extranet web pages. Upgrade and Maintenance Manual...
Page 100: Performing A Raid Array Rebuild
Basic software procedures 5.2.14 Performing a RAID array rebuild After replacing a hard disk drive that has been combined into a RAID array, RAID rebuild will be performed completely unattended as a background process. Ê Ensure that the RAID array rebuild has started normally. Wait until the progress bar has reached at least one percent.
Page 101: Looking Up Wwn Addresses
Basic software procedures Ê Under Network Inventory, you will find detailed information on each network controller in the managed PRIMERGY server, including its MAC address. This information is only available with the iRMC S4 or above. Only network controllers supporting the Command Line Protocol (CLP) will be displayed.
Page 102: Using The Chassis Id Prom Tool
After replacing the Chassis ID EPROM, system information has to be entered using the Chassis ID Prom tool. The tool and further instructions are available to maintenance personnel from the Fujitsu Technology Solutions Extranet: https://partners.ts.fujitsu.com/com/service/ps/Servers/PRIMERGY/ Ê Select your PRIMERGY system from the main area of the page.
Page 103: After Replacing / Upgrading Lan Controllers
Basic software procedures – LAN Team Statistics: Available statistics about the selected LAN team For more detailed information, refer to the "ServerView Operations Manager - Server Management" user guide. 5.2.17.1 After replacing / upgrading LAN controllers Please note when re-using a replaced LAN controller: Ê...
Page 104: Performing A Fan Test After Replacing A Defective Fan
Basic software procedures Using the iRMC web frontend Ê Enter the ServerView iRMC web frontend. Ê Under System Overview, click Identify LED Off to switch off the ID indicators. Using ServerView Operations Manager Ê In ServerView Operations Manager Single System View and press the Locate button in the title bar to switch off the ID indicator.
Page 105 Basic software procedures Ê Under Daily Fan Test, set the daily fan test time to a few minutes from the current time. (Ensure to note down your previous setting.) Ê Click Save Page. The fan test will be started at the specified time. Ê...
Page 106 Basic software procedures Upgrade and Maintenance Manual TX1320 M1...
Page 107: Power Supply
This chapter provides information on how to handle a standard power supply unit (PSU). About power supply configurations The PRIMERGY TX1320 M1 server is equipped with a standard PSU. CAUTION! The server supports a mains voltage in the range of 100 V - 240 V. You may only operate the server if its rated voltage range corresponds to the local mains voltage.
Page 108: Standard Power Supply Unit
Power supply Standard power supply unit 6.1.1 Replacing the standard power supply unit Field Replaceable Unit Hardware: 10 minutes (FRU) tool-less (preliminary and concluding steps) Tools: Phillips PH2 / (+) No. 2 screw drive (replacing the PSU) 6.1.1.1 Preliminary steps Before replacing the standard PSU, perform the following steps: You are advised to perform this routine with the server in a horizontal position.
Page 109: Disconnecting Internal Power Cables
Power supply 6.1.1.2 Disconnecting internal power cables Figure 29: Disconnecting internal power cables Ê Disconnect the PSU power management connector from system board connector PC2009 (1). Ê While pressing the release latch (see arrow) on the connector, disconnect the PSU ATX power connector from system board connector POWER1 (2) Upgrade and Maintenance Manual TX1320 M1...
Page 110: Removing The Psu
Power supply 6.1.1.3 Removing the PSU Figure 30: Removing the PSU Ê Remove four screws from the PSU (see circles). Ê Slide the defective PSU inward by 3 cm (1) to disengage the locking mechanism. Ê Lift the defective PSU out of the chassis (2). Upgrade and Maintenance Manual TX1320 M1...
Page 111: Installing The Psu
Power supply 6.1.1.4 Installing the PSU Figure 31: Installing the PSU (A) Figure 32: Installing the standard PSU (B) Upgrade and Maintenance Manual TX1320 M1...
Page 112 Power supply Ê Insert the PSU into the chassis leaving a gap of about 3 cm to the rear chassis wall (1) in figure Ê Ensure that the mounting bracket on the chassis (see circle in figure engages with the notch on the lower surface of the PSU. Ê...
Page 113: Reconnecting Internal Power Cables
Power supply 6.1.1.5 Reconnecting internal power cables Figure 34: Connecting internal power cables Ê Connect the PSU ATX power connector to system board connector POWER1 (1). Ê Connect the PSU power management connector to system board connector PC2009 (2). Upgrade and Maintenance Manual TX1320 M1...
Page 114: Concluding Steps
Power supply 6.1.1.6 Concluding steps Perform the following procedures to complete the task: Ê Close the server cover as described in section "Closing the server" on page Ê Reconnect the AC power cord to the PSU. "Performing a fan test after replacing a defective fan" on page 104 Ê...
Page 115: Hard Disk Drives / Solid State Drives
Hard disk drives / solid state drives This chapter provides information on how to install or remove HDD / SSD modules and how to replace the SAS backplane. For information on SAS RAID controllers, please refer to chapter "Expansion cards and backup units" on page 171.
Page 116: Basic Procedure
Hard disk drives / solid state drives For further safety information, please refer to chapter "Important ● information" on page In this chapter – 2.5-inch HDD / SSD subsystem "Installing 2.5-inch HDD / SSD modules" on page 118 ● "Removing 2.5-inch HDD / SSD modules" on page 122 ●...
Page 117: Inch Hard Disk Drives / Solid State Drives
Hard disk drives / solid state drives 2.5-inch hard disk drives / solid state drives 7.2.1 Mounting order for 2.5-inch HDDs / SSDs Maximum configuration: 4x 2.5-inch HDDs / SSDs Figure 35: 2.5-inch HDD / SSD mounting order 7.2.1.1 HDD/SSD naming scheme RAID Manager Channel Logical drive number...
Page 118: Installing 2.5-Inch Hdd / Ssd Modules
Hard disk drives / solid state drives 7.2.2 Installing 2.5-inch HDD / SSD modules Customer Replaceable Unit Hardware: 5 minutes (CRU) Preliminary and concluding steps: tool-less Tools: Installing a 2.5-inch HDD / SSD module: tool-less 7.2.2.1 Preliminary steps Before installing a 2.5-inch HDD / SSD module, perform the following steps: Ê...
Page 119: Removing A 2.5-Inch Hdd / Ssd Dummy Module
Hard disk drives / solid state drives 7.2.2.2 Removing a 2.5-inch HDD / SSD dummy module Figure 36: Removing a 2.5-inch HDD / SSD dummy module Dummy modules have been installed into unused HDD / SSD bays. Before installing an additional HDD / SSD, the dummy module needs to be removed from the desired drive bay.
Page 120: Installing A 2.5-Inch Hdd / Ssd Module
Hard disk drives / solid state drives 7.2.2.3 Installing a 2.5-inch HDD / SSD module Figure 37: Opening the 2.5-inch HDD / SSD module locking lever Ê Pinch the green locking clips (1) and open the locking lever (2). Upgrade and Maintenance Manual TX1320 M1...
Page 121: Concluding Steps
Hard disk drives / solid state drives Figure 38: Inserting the 2.5-inch HDD / SSD module Ê Insert the HDD module into a drive bay and carefully push back as far as it will go (1). Ê Close the locking lever to lock the hard disk drive in place (2). 7.2.2.4 Concluding steps Perform the following procedures to complete the task:...
Page 122: Removing 2.5-Inch Hdd / Ssd Modules
All data on all HDDs / SSDs in the array will be lost! Be sure to back up your data before deleting a RAID array. For further information, please refer to the "ServerView Suite RAID Management" user guide, available online at http://manuals.ts.fujitsu.com (EMEA market) or (Japanese http://jp.fujitsu.com/platform/server/primergy/manual/ market) or from the ServerView Suite DVD supplied with your PRIMERGY server.
Page 123: Removing A 2.5-Inch Hdd / Ssd Module
Hard disk drives / solid state drives 7.2.3.2 Removing a 2.5-inch HDD / SSD module Figure 39: Disconnecting a 2.5-inch HDD / SSD module Ê Pinch the green locking clips (1) and fully open the locking lever (2). Thereby, the HDD / SSD module is pushed out of its drive bay by about 1 cm and disconnected from the SAS / SATA backplane.
Page 124 Hard disk drives / solid state drives Figure 40: Removing a 2.5-inch HDD / SSD module Ê Pull the HDD / SSD module completely out of its bay. Upgrade and Maintenance Manual TX1320 M1...
Page 125: Installing A 2.5-Inch Hdd / Ssd Dummy Module
Hard disk drives / solid state drives 7.2.3.3 Installing a 2.5-inch HDD / SSD dummy module CAUTION! If the removed HDD / SSD module is not replaced immediately, always replace a dummy module into the unused HDD / SSD bay to comply with applicable EMC regulations and satisfy cooling requirements.
Page 126: Replacing A 2.5-Inch Hdd / Ssd Module
Only remove an HDD / SSD module during operation if the drive is ● not currently being accessed. Observe the indicators for the corresponding HDD / SSD modules, see "FUJITSU Server PRIMERGY TX1320 M1 Operating Manual". Under no circumstances should you remove an HDD / SSD module ●...
Page 127: Removing A 2.5-Inch Hdd / Ssd Module
Hard disk drives / solid state drives 7.2.4.2 Removing a 2.5-inch HDD / SSD module Ê Remove the HDD / SSD module to be replaced from the server as described in section "Removing a 2.5-inch HDD / SSD module" on page 123.
Page 128: Inch Hard Disk Drives
Hard disk drives / solid state drives 3.5-inch hard disk drives 7.3.1 Mounting order for 3.5-inch HDDs Maximum configuration: 2x 3.5-inch HDDs Figure 42: 3.5-inch HDD mounting order HDD naming scheme RAID Manager Channel Logical drive number Upgrade and Maintenance Manual TX1320 M1...
Page 129: Installing 3.5-Inch Hdd Modules
Hard disk drives / solid state drives SAS connectivity Controller Channel Connection Drives 1-2 SATA cable (Y3963-V101) from Onboard HDD backplane connector X1 to system board connector SATA MLC 1. 7.3.2 Installing 3.5-inch HDD modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 7.3.2.1...
Page 130: Installing A 3.5-Inch Hdd Module
Hard disk drives / solid state drives 7.3.2.2 Installing a 3.5-inch HDD module Ê Detach and remove the Easyclick rails from the desired 3.5-inch HDD installation bay. Align the three pins on the Easyclick rails with the screw holes on the new hard disk drive.
Page 131 Hard disk drives / solid state drives Figure 44: Inserting the 3.5-inch HDD module Ê Insert the hard disk drive into its installation bay. Upgrade and Maintenance Manual TX1320 M1...
Page 132 Hard disk drives / solid state drives Figure 45: Installing the 3.5-inch HDD module Ê Slide the hard disk drive into its installation bay until the locking latches engage (see circle). Upgrade and Maintenance Manual TX1320 M1...
Page 133: Concluding Steps
Hard disk drives / solid state drives Figure 46: Connecting the cables Ê Connect the 15-pin SATA power connectors on SATA power cable T26139- Y4012-V501 to the hard disk drives (1). Ê Connect the two SATA connectors P1 (2) and P2 (3) on the SATA Y-cable (T26139-Y3964-V201) to the hard disk drives.
Page 134: Removing 3.5-Inch Hdd Modules
All data on all HDDs in the array will be lost! Be sure to back up your data before deleting a RAID array. For further information, please refer to the "ServerView Suite RAID Management" user guide, available online at http://manuals.ts.fujitsu.com (EMEA market) or (Japanese http://jp.fujitsu.com/platform/server/primergy/manual/ market) or from the ServerView Suite DVD supplied with your PRIMERGY server.
Page 135: Removing A 3.5-Inch Hdd Module
Hard disk drives / solid state drives 7.3.3.2 Removing a 3.5-inch HDD module Figure 47: Disconnecting the cables from the a 3.5-inch HDD module Ê Disconnect the power cable (2) and data cable (1). Upgrade and Maintenance Manual TX1320 M1...
Page 136 Hard disk drives / solid state drives Figure 48: Removing a 3.5-inch HDD module Ê Pull the HDD module with the two green handles of the Easyclick rails completely out of its bay. Figure 49: Inserting the Easyclick rails Ê Insert the Easyclick rails into the bay (1). Ê...
Page 137: Concluding Steps
Only remove an HDD module during operation if the drive is not ● currently being accessed. Observe the indicators for the corresponding HDD modules, see "FUJITSU Server PRIMERGY TX1320 M1 Operating Manual". Under no circumstances should you remove an HDD module while ●...
Page 138: Preliminary Steps
All data on all HDDs in the array will be lost! Be sure to back up your data before deleting a RAID array. For further information, please refer to the "ServerView Suite RAID Management" user guide, available online at http://manuals.ts.fujitsu.com (EMEA market) or http://jp.fujitsu.com/platform/server/primergy/manual/ (Japanese market) or from the ServerView Suite DVD supplied with your PRIMERGY server.
Page 139: Installing A 3.5-Inch Hdd Module
Hard disk drives / solid state drives 7.3.4.3 Installing a 3.5-inch HDD module Ê Install the replacement HDD module into the empty drive bay as described in section "Installing a 3.5-inch HDD module" on page 130. 7.3.4.4 Concluding steps Perform the following procedures to complete the task: Ê...
Page 140: Replacing Sas / Sata Backplane
Hard disk drives / solid state drives Replacing SAS / SATA backplane Field Replaceable Unit Hardware: 10 minutes (FRU) Preliminary and concluding steps: tool-less Tools: Replacing the SAS backplane: Phillips PH2 / (+) No. 2 screw driver 7.4.1 Replacing 2.5- inch SAS / SATA backplane 7.4.1.1 Preliminary steps The 2.5-inch HDD SAS / SATA backplane is mounted on the drive cage.
Page 141 Hard disk drives / solid state drives Figure 50: Disconnecting the SATA cables from the system board Ê Disconnect the SATA cable from the system board. Ê Open the front cage as described in section "Opening the front cage" on page Ê...
Page 142: Removing The Air Duct (If Applicable)
Hard disk drives / solid state drives 7.4.1.2 Removing the air duct (if applicable) Figure 51: Lifting up the air duct Ê Lift up the right cant of the air duct. Figure 52: Removing the air duct Ê Remove the air duct in direction of the arrow. Upgrade and Maintenance Manual TX1320 M1...
Page 143: Removing The 2.5-Inch Hdd Sas / Sata Backplane
Hard disk drives / solid state drives 7.4.1.3 Removing the 2.5-inch HDD SAS / SATA backplane Figure 53: Disconnecting cables from the 2.5-inch HDD SAS / SATA backplane Ê Disconnect the SATA cables from the 2.5-inch HDD SAS / SATA backplane. Ê...
Page 144 Hard disk drives / solid state drives Figure 54: Removing the 2.5-inch HDD SAS / SATA backplane Ê At a slight angle, unhinge the 2.5-inch HDD SAS / SATA backplane from the guides on the front cage and remove it. Upgrade and Maintenance Manual TX1320 M1...
Page 145: Installing The 2.5-Inch Hdd Sas / Sata Backplane
Hard disk drives / solid state drives 7.4.1.4 Installing the 2.5-inch HDD SAS / SATA backplane Figure 55: Installing the 2.5-inch HDD SAS / SATA backplane Ê At a slight angle, fit the new 2.5-inch HDD SAS/SATA backplane into the two guides on the drive cage.
Page 146 Hard disk drives / solid state drives Figure 56: Connecting cables from the 2.5-inch HDD SAS / SATA backplane Ê Secure the 2.5-inch HDD SAS/SATA backplane on the drive cage with the two screws (M3 x 4.5 mm). Ê Reconnect the SATA cable to the 2.5-inch HDD SAS/SATA backplane. Upgrade and Maintenance Manual TX1320 M1...
Page 147: Installing The Air Duct (If Applicable)
Hard disk drives / solid state drives 7.4.1.5 Installing the air duct (if applicable) Figure 57: Inserting the air duct Ê Insert the air duct in a slight angle. Figure 58: Positioning the air duct Ê Push the air duct to the chassis as far as possible. Upgrade and Maintenance Manual TX1320 M1...
Page 148: Concluding Steps
Hard disk drives / solid state drives 7.4.1.6 Concluding steps Ê Install the HDD fan as described in section "Installing the HDD fan module" on page 170. For a complete cabling overview, please refer to section "Cabling" on page 319. Ê...
Page 149 Hard disk drives / solid state drives Ê Reconnect the AC power cord to the power supply unit. Ê If BitLocker functionality is used and has been disabled before starting the maintenance task, re-enable BitLocker as described in section "Enabling BitLocker functionality"...
Page 150 Hard disk drives / solid state drives Upgrade and Maintenance Manual TX1320 M1...
Page 151: System Fan And Hdd Fan
This chapter provides information on how to replace the system fan module. Basic information The PRIMERGY TX1320 M1 server features two system fan modules. Additional fans in PSU modules are integral parts of the power supply units and cannot be replaced separately.
Page 152: Replacing The System Fan Module
System fan and HDD fan Replacing the system fan module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 8.1.1 Preliminary steps Before replacing the fan module, perform the following steps: Ê Locate the defective server as described in section "Locating the defective server"...
Page 153: Removing The System Fan Module
System fan and HDD fan 8.1.2 Removing the system fan module Figure 60: Disconnecting the cable of the system fan module Ê Disconnect the fan cable from system board connector FAN1 SYS. Figure 61: Removing the system fan module Ê Pull the locking lever (1). Upgrade and Maintenance Manual TX1320 M1...
Page 154: Removing The Fan From The Holder
System fan and HDD fan Ê Push the fan module in the direction of arrow (2) to disengage the retaining brackets on the server rear. Ê Lift the fan module out of the chassis (3). 8.1.3 Removing the fan from the holder Figure 62: Removing the fan from the holder Ê...
Page 155: Installing The Fan Into The Holder
System fan and HDD fan 8.1.4 Installing the fan into the holder Figure 63: Inserting the fan into the 3.5-inch holder Ê Route the cable as shown (see circle). Ê Insert the fan into the holder (see arrow). Upgrade and Maintenance Manual TX1320 M1...
Page 156: Installing The System Fan Module
System fan and HDD fan 8.1.5 Installing the system fan module Figure 64: Installing the system fan module (A) Upgrade and Maintenance Manual TX1320 M1...
Page 157 System fan and HDD fan Figure 65: Installing the system fan module (B) Ê Fit the four hooks on the fan module into the slots in the chassis (see blue circles). Ê Slide the system fan holder to the right as far as it will go until its hooks engage with the narrow ends of the keyhole slots in the chassis (circles).
Page 158: Concluding Steps
System fan and HDD fan Figure 66: Connecting the system fan cable Ê Connect the fan cable to system board connector FAN1 SYS. 8.1.6 Concluding steps Ê Close the server cover as described in section "Closing the server" on page Ê...
Page 159: Replacing The Hdd Fan Module
System fan and HDD fan Replacing the HDD fan module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 8.2.1 Replacing the HDD fan module for 3.5-inch version 8.2.1.1 Preliminary steps Before replacing the HDD fan module, perform the following steps: Ê...
Page 160: Removing The Hdd Fan Module
System fan and HDD fan 8.2.1.2 Removing the HDD fan module Figure 67: Removing the HDD fan module Ê Pull the locking lever (1). Ê Push the fan module in the direction of arrow (2) to disengage the retaining brackets on the server rear. Ê...
Page 161: Removing The Fan From The Holder
System fan and HDD fan 8.2.1.3 Removing the fan from the holder Figure 68: Removing the fan from the 3.5-inch holder Ê Unlock the fan (see circles). Ê Remove the fan from the holder (see arrow). Upgrade and Maintenance Manual TX1320 M1...
Page 162: Installing The Fan Into The Holder
System fan and HDD fan 8.2.1.4 Installing the fan into the holder Figure 69: Inserting the fan into the 3.5-inch holder Ê Route the cable as shown (see circle). Ê Insert the fan into the holder (see arrow). Upgrade and Maintenance Manual TX1320 M1...
Page 163: Installing The Hdd Fan Module
System fan and HDD fan 8.2.1.5 Installing the HDD fan module Figure 70: Regarding the retaining bracklets Ê Regard the 3 retaining bracklets on the rear side of the front cage (see blue circles). Upgrade and Maintenance Manual TX1320 M1...
Page 164: Concluding Steps
System fan and HDD fan Figure 71: Installing the HDD fan module Ê Insert the HDD fan module so that the three hooks on the fan module fit into the slots in the chassis (1). Ê Slide the HDD fan module as far as it will go until its hooks engage with the narrow ends of the keyhole slots in the chassis (2).
Page 165: Replacing The Hdd Fan Module For 2.5-Inch Version
System fan and HDD fan 8.2.2 Replacing the HDD fan module for 2.5-inch version Figure 72: Position of the additional air duct 8.2.2.1 Required tools Preliminary and concluding steps: tool-less ● Replacing the fan module: tool-less ● 8.2.2.2 Preliminary steps Before replacing the HDD fan module, perform the following steps: Ê...
Page 166: Removing The Hdd Fan Module
System fan and HDD fan 8.2.2.3 Removing the HDD fan module Figure 73: Removing the HDD fan module Ê Push on the locking lever (1) to disengage the HDD fan module holder out of the retaining brackets. Ê Lift the HDD fan module holder with the fan module out of the chassis (2). Upgrade and Maintenance Manual TX1320 M1...
Page 167 System fan and HDD fan Figure 74: Removing the power cable from the HDD fan module Ê Remove the power cable from the SAS/SATA backplane. Upgrade and Maintenance Manual TX1320 M1...
Page 168: Removing The Fan From The Holder
System fan and HDD fan 8.2.2.4 Removing the fan from the holder Figure 75: Removing the fan from the 2.5-inch holder Ê Unlock the fan (see circles). Ê Remove the fan from the holder (see arrow). Upgrade and Maintenance Manual TX1320 M1...
Page 169: Installing The Fan Into The Holder
System fan and HDD fan 8.2.2.5 Installing the fan into the holder Figure 76: Inserting the fan into the 3.5-inch holder Ê Route the cable as shown through the slot (see circle). Ê Insert the fan into the holder (see arrow). Upgrade and Maintenance Manual TX1320 M1...
Page 170: Installing The Hdd Fan Module
System fan and HDD fan 8.2.2.6 Installing the HDD fan module Figure 77: Inserting the HDD fan module holder Ê Insert the hooks of the HDD fan module holder (see blue circles). Ê Fold the fan module holder back to the front cage and press it down so that the retaining bracket engages.
Page 171: Expansion Cards And Backup Units
Expansion cards and backup units This chapter provides information on how to install, remove or replace expansion cards and backup units. For information on SAS / SATA backplanes, please refer to chapter "Hard disk drives / solid state drives" on page 115.
Page 172: Basic Procedure
Expansion cards and backup units In this chapter "Installing expansion cards" on page 174 ● "Removing expansion cards" on page 178 ● "Replacing expansion cards" on page 181 ● "Mounting expansion card slot brackets" on page 199 ● "Handling SFP+ transceiver modules" on page 207 ●...
Page 173: Expansion Cards And Backup Units
Riser Card for 32-bit PCI cards with PCI adapter board For the latest information on supported expansion cards, refer your server’s hardware configurator available online at the following address: for the EMEA market: http://ts.fujitsu.com/products/standard_servers/tower/primergy_tx1320m1.html for the Japanese market: http://jp.fujitsu.com/platform/server/primergy/system/ Upgrade and Maintenance Manual TX1320 M1...
Page 174: Expansion Cards
Expansion cards and backup units Expansion cards 9.2.1 Installing expansion cards Hardware: 5 minutes Upgrade and Repair Unit (URU) Software: 5 minutes Tools: tool-less 9.2.1.1 Preliminary steps Before installing an expansion card, perform the following steps: Ê Disable BitLocker functionality as described in section "Disabling BitLocker functionality"...
Page 175: Removing A Pci Slot Bracket
Expansion cards and backup units 9.2.1.2 Removing a PCI slot bracket Figure 79: Opening the PCI slot bracket clamp Ê Fold up the slot bracket clamp. Figure 80: Removing the PCI slot bracket Ê Remove the slot bracket. CAUTION! Keep the slot bracket for further use. Always replace slot brackets into unused PCI slot openings to comply with applicable EMC regulations and satisfy cooling requirements.
Page 176: Installing An Expansion Card
Expansion cards and backup units 9.2.1.3 Installing an expansion card Ê Remove the expansion card from its protective packaging. For further instructions regarding controller settings, please refer to the accompanying documentation. Ê If applicable, attach the required slot bracket to the expansion card as described in section "Mounting expansion card slot brackets"...
Page 177: Connecting Cables To The Expansion Card
Expansion cards and backup units 9.2.1.4 Connecting cables to the expansion card Ê If applicable, connect internal cables to the expansion card. For a complete cabling overview, please refer to section "Cabling" on page 319. 9.2.1.5 Concluding steps Perform the following procedures to complete the task: Ê...
Page 178: Removing Expansion Cards
Expansion cards and backup units 9.2.2 Removing expansion cards Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 9.2.2.1 Preliminary steps Before removing an expansion card, perform the following steps: Ê Locate the defective server as described in section "Locating the defective server"...
Page 179: Removing An Expansion Card
Expansion cards and backup units 9.2.2.2 Removing an expansion card Figure 82: Removing an expansion card Ê Fold up the locking handle on the slot bracket clamp. Ê If applicable, remove SFP+ transceiver modules from the expansion card, as described in section "Replacing SFP+ transceiver modules"...
Page 180: Installing A Pci Slot Bracket
Expansion cards and backup units 9.2.2.3 Installing a PCI slot bracket CAUTION! Always replace slot brackets into unused PCI slot openings to comply with applicable EMC regulations and satisfy cooling requirements. Figure 83: Installing a PCI slot bracket Ê Insert a PCI slot bracket into the unused PCI slot opening. Ê...
Page 181: Replacing Expansion Cards
Expansion cards and backup units Ê If BitLocker functionality is used and has been disabled before starting the maintenance task, re-enable BitLocker as described in section "Enabling BitLocker functionality" on page 9.2.3 Replacing expansion cards Hardware: 5 minutes Upgrade and Repair Unit (URU) Software: 5 minutes Tools: tool-less...
Page 182: Removing An Expansion Card
Expansion cards and backup units 9.2.3.2 Removing an expansion card Ê If applicable, remove SFP+ transceiver modules from the expansion card to be removed, as described in section "Replacing SFP+ transceiver modules" on page 214. Ê Remove the defective expansion card as described in section "Removing expansion cards"...
Page 183 Expansion cards and backup units Ê If applicable, reconfigure your network settings in the operation system according to the original configuration of the replaced controller (expansion card or onboard). Ê If applicable, restore LAN teaming configurations as described in section "After replacing / upgrading LAN controllers"...
Page 184: Replacing Tfm
Expansion cards and backup units 9.2.4 Replacing TFM Upgrade and Repair Unit Hardware: 5 minutes (URU) Preliminary and concluding steps: tool-less Tools: Replacing an TFM: Phillips PH1 / (+) No.1 screw drive 9.2.4.1 Preliminary steps Before replacing a TFM, perform the following steps: Ê...
Page 185: Installing The New Tfm
Expansion cards and backup units Figure 84: Removing the TFM Ê Remove the three screws (1). Ê Remove the TFM (2). 9.2.4.3 Installing the new TFM Ê Install the new TFM as described in section "Installing TFM to the RAID controller (if applicable)"...
Page 186: Backup Units
Expansion cards and backup units Backup Units The Backup Unit backs up the memory contents of the connected SAS RAID controller in the event of a power failure. 9.3.1 Installing an FBU Upgrade and Repair Unit Hardware: 5 minutes (URU) Preliminary and concluding steps: tool-less Tools: Installing an FBU: tool-less...
Page 187: Installing Tfm To The Raid Controller (If Applicable)
Expansion cards and backup units 9.3.1.2 Installing TFM to the RAID controller (if applicable) Figure 85: TFM kit Screws Figure 86: Installing TFM Ê Fit the spacer bolts of the TFM on the RAID controller (1). Ê Fasten the TFM on the RAID controller with the three screws from the TFM kit (screw torque: 0.4 Nm)(2).
Page 188: Preparing The Fbu
Expansion cards and backup units 9.3.1.3 Preparing the FBU Figure 87: Installing the FBU in the FBU holder (A) Ê At a slight angle, fit the FBU under both retaining brackets of the FBU holder as shown. Ê Push in the FBU until it locks in place. Figure 88: Installing the FBU in the FBU holder (B) Ê...
Page 189: Installing The Fbu Holder Into The Chassis
Expansion cards and backup units Figure 89: Connecting the FBU adapter cable to the FBU Ê Connect the cable end on the FBU to the FBU adapter cable as shown. 9.3.1.4 Installing the FBU holder into the chassis Figure 90: Installing the FBU holder Upgrade and Maintenance Manual TX1320 M1...
Page 190: Connecting The Fbu Adapter Cable To The Tfm
Expansion cards and backup units Ê Insert the holder into the chassis so that the three shoulder screw caps on the chassis floor rest in the wide ends of the keyhole slots on the holder (1). Ê Slide the holder to the right as far as it will go. The shoulder screw caps on the chassis floor will lock in the narrow ends of the keyhole slots on the holder (2).
Page 191: Concluding Steps
Expansion cards and backup units Figure 92: Cabling of the FBU Ê Run the FBU adapter cable through the middle cable bracket as shown (see circle) (1). Ê Connect the FBU adapter cable to the TFM module on the SAS RAID controller D3116 (2).
Page 192: Removing An Fbu
Do not throw FBUs into the trash can. Batteries must be disposed of in accordance with local regulations concerning special waste. For further safety information, please refer to section "Environmental protection" in the FUJITSU Server PRIMERGY TX1320 M1 Operating Manual. 9.3.2.1...
Page 193: Disconnecting The Fbu Adapter Cable From The Tfm
Expansion cards and backup units 9.3.2.2 Disconnecting the FBU adapter cable from the TFM Figure 93: Disconnecting the FBU adapter cable from the TFM Ê Disconnect the FBU adapter cable from the TFM. Ê Remove the FBU adapter cable from the cable clamp. 9.3.2.3 Removing the FBU holder from the chassis Figure 94: Removing the FBU holder...
Page 194: Concluding Steps
Expansion cards and backup units Ê Remove the FBU cable from the cable clamp (1).. Ê Carefully disconnect the FBU cable from the RAID controller (2). Figure 95: Installing the FBU holder Ê Lift up the green locking handle on the FBU holder and slide the FBU holder to the left as far as it will go (1).
Page 195: Replacing An Fbu
Do not throw FBUs into the trash can. Batteries must be disposed of in accordance with local regulations concerning special waste. For further safety information, please refer to section "Environmental protection" in the FUJITSU Server PRIMERGY TX1320 M1 Operating Manual. 9.3.3.1...
Page 196: Removing The Fbu From The Fbu Holder
Expansion cards and backup units 9.3.3.3 Removing the FBU from the FBU holder Figure 96: Disconnecting the FBU adapter cable from the FBU Ê Press down on the locking latch on the FBU cable (see close-up) and disconnect the FBU adapter cable. Upgrade and Maintenance Manual TX1320 M1...
Page 197: Installing A Replacement Fbu
Expansion cards and backup units Figure 97: Removing the FBU from the FBU holder Ê At a slight angle, slide the FBU from under the retaining brackets of the FBU holder and remove it. 9.3.3.4 Installing a replacement FBU Ê Install the new FBU into the FBU holder as described in section "Preparing the FBU"...
Page 198: Concluding Steps
Expansion cards and backup units 9.3.3.5 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in section "Closing the front cage" on page Ê Close the server cover as described in section "Closing the server"...
Page 199: Additional Tasks
Expansion cards and backup units Additional tasks This section provides additional expansion card related information on how to install slot brackets and SFP+ transceiver modules. For further instructions regarding controller settings, please refer to the accompanying documentation. 9.4.1 Mounting expansion card slot brackets Customer Replaceable Unit Hardware: 5 minutes (CRU)
Page 200: General Instructions
Expansion cards and backup units 9.4.1.1 General instructions Ê Place the controller on the mounting tabs on the slot bracket (1). Ê Secure the slot bracket to the controller with two M3 x 4.5 mm screws. Use the following slot bracket for the ModularRAID controllers based on LSI MegaRAID: –...
Page 201: Network Adapter D2735
Expansion cards and backup units 9.4.1.2 Network adapter D2735 Figure 99: Network adapter D2735 - Mounting the slot bracket (A) Ê Place the controller on the mounting tabs on the slot bracket (1). Ê Carefully shift the slot bracket towards the controller (2) until the plug shells engage with the cut-outs in the slot bracket connector panel (see circle).
Page 202 Expansion cards and backup units Figure 100: Network adapter D2735 - Mounting the slot bracket (B) Ê Secure the slot bracket to the controller with two M3 x 4.5 mm screws. Figure 101: Network adapter D2735 - Mounting the slot bracket (C) Assembled network adapter D2735 Upgrade and Maintenance Manual TX1320 M1...
Page 203: Network Adapter D2745
Expansion cards and backup units 9.4.1.3 Network adapter D2745 Figure 102: Network adapter D2745 - Mounting the slot bracket (A) Ê Hinge the slot bracket to the plug shell as shown (1). Ê Fold the slot bracket towards the controller until the threaded mounting tab is aligned with the screw hole on the controller (2).
Page 204 Expansion cards and backup units Figure 103: Network adapter D2745 - Mounting the slot bracket (B) Ê Secure the slot bracket to the controller with one M3 x 4.5 mm screw. Figure 104: Network adapter D2745 - Mounting the slot bracket (C) Assembled network adapter D2745 Upgrade and Maintenance Manual TX1320 M1...
Page 205: Network Adapter D2755
Expansion cards and backup units 9.4.1.4 Network adapter D2755 Figure 105: Network adapter D2755 - Mounting the slot bracket (A) Ê Place the controller on the mounting tabs on the slot bracket (1). Ê Carefully shift the slot bracket towards the controller until the plug shells engage with the cut-outs in the slot bracket connector panel (2).
Page 206 Expansion cards and backup units Figure 106: Network adapter D2755 - Mounting the slot bracket (B) Ê Secure the slot bracket to the controller with two M3 x 4.5 mm screws. Figure 107: Network adapter D2755 - Mounting the slot bracket (C) Assembled network adapter D2755 Upgrade and Maintenance Manual TX1320 M1...
Page 207: Handling Sfp+ Transceiver Modules
Expansion cards and backup units 9.4.2 Handling SFP+ transceiver modules For Fiber Channel over Ethernet (FCoE) configurations, the Ethernet server adapter is equipped with one or two SFP+ (small form-factor pluggable) transceiver modules. 9.4.2.1 Installing SFP+ transceiver modules Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less...
Page 208 Expansion cards and backup units Ê Remove the SFP+ transceiver module from its protective packaging. Ê Remove the optical port plug from the new / additional SFP+ transceiver module. CAUTION! – Always keep the protective port plugs attached to the transceiver optical bores and fiber-optic cable connectors until you are ready to make a connection.
Page 209 Expansion cards and backup units Inserting the SFP+ transceiver module Figure 110: Inserting the SFP+ transceiver module Ê Insert and slide the SFP+ transceiver module into the socket connector as far as it will go. If only one slot is equipped with a SFP+ transceiver module, use the primary connector as shown.
Page 210 Expansion cards and backup units Figure 111: Latching the locking bail Ê Carefully fold up and latch the locking bail. Figure 112: Attaching the protective optical port plug Ê If the SFP+ transceiver module is not immediately connected to an LC connector, attach the protective optical port plug to the transceiver optical bores.
Page 211 Expansion cards and backup units Installing the secondary SFP+ transceiver module Figure 113: Installing the secondary SFP+ transceiver module Ê If applicable, install the secondary SFP+ transceiver module accordingly. Upgrade and Maintenance Manual TX1320 M1...
Page 212: Removing An Sfp+ Transceiver Module
Expansion cards and backup units 9.4.2.2 Removing an SFP+ transceiver module Customer Replaceable Unit Hardware: 10 minutes (CRU) Tools: tool-less For Fiber Channel over Ethernet (FCoE) configurations, the ethernet server adapter is equipped with one or two SFP+ (small form-factor pluggable) transceiver modules.
Page 213 Expansion cards and backup units Figure 115: Unlatching the locking bail Ê Carefully unlatch and fold down the locking bail on the SFP+ transceiver module to eject the transceiver from the socket connector. Figure 116: Removing the SFP+ transceiver Ê Pull the SFP+ transceiver module out of its socket connector. Ê...
Page 214: Replacing Sfp+ Transceiver Modules
Expansion cards and backup units 9.4.2.3 Replacing SFP+ transceiver modules Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less For Fiber Channel over Ethernet (FCoE) configurations, the ethernet server adapter is equipped with one or two SFP+ (small form-factor pluggable) transceiver modules.
Page 215: Main Memory
Main memory This section provides information on how to install, remove or replace memory modules. Safety notes CAUTION! Do not install unsupported third party memory modules. For further ● information on supported memory modules, refer to section "Basic information" on page 216.
Page 216: Basic Information
Main memory 10.1 Basic information – The system board is equipped with four memory slots. – The system has to be equipped with at least one memory module. – Supported memory modules: DDR3L 1333 or 1600 unbuffered single rank (SR) or dual rank (DR) UDIMMs with ECC –...
Page 217: Memory Sequence
Main memory 10.1.1 Memory sequence – Populate memory slot 1 / channel A (DIMM-1A) first. – Within both channels, memory slot 1 must be populated prior to slot 2. – If memory modules with different capacities are used: – Install modules with higher capacities first. –...
Page 218: Operation Modes
Main memory 10.1.2 Operation modes – The maximum performance can be achieved in a symmetric dual-channel configuration. Therefore both channels have to be populated with the same amount of memory. The DRAM device technology (1 Gbit / 2 Gbit / 4 Gbit) may vary from one channel to the other.
Page 219: Removing A Memory Module
Main memory 10.2.2 Removing a memory module Ê Identify the desired memory slot see section "Memory sequence" on page 217. CAUTION! Ensure to maintain an operational configuration when removing memory modules. For additional information, please refer to section "Basic information" on page 216.
Page 220: Installing Memory Modules
Main memory 10.3 Installing memory modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 10.3.1 Preliminary steps "Disabling BitLocker functionality" on page 73 Ê "Disabling SVOM boot watchdog functionality" on page 74 Ê "Shutting down the server" on page 52 Ê...
Page 221: Concluding Steps
Main memory Ê Align the notch on the bottom of the module with the crossbar in the slot (see close-up). Ê Press down on the memory module until the securing clips snap into the cutouts at each end of the module (2). 10.3.3 Concluding steps "Installing the system fan module"...
Page 222: Removing The Defective Memory Module
Main memory "Disconnecting power cords" on page 53 Ê "Opening the server" on page 55 Ê "Removing the system fan module" on page 153 Ê Ê Locate the defective memory module using the onboard Local Diagnostic LEDs (see section "Onboard indicators and controls" on page 328).
Page 223: Processors
Processors This section provides information on how to replace the processor and processor heat sink. Safety notes CAUTION! Do not install unsupported processors. For further information on ● supported processors, refer to section "Basic information" on page 224. Circuit boards and soldered parts of internal options are exposed and ●...
Page 224: Basic Information
Processors 11.1 Basic information Supported processors The system board is equipped with one LGA 1150 socket for dual and quad Core Intel Xeon E3-1200v3 processor series CPUs. 11.2 Upgrading or replacing the processor Field Replaceable Unit Hardware: 15 minutes (FRU) Software: 5 minutes Tools: Phillips PH2 / (+) No.
Page 225: Removing The Processor Heat Sink
Processors 11.2.2 Removing the processor heat sink Figure 120: Removing the processor heat sink Ê Loosen the four captive screws on the heat sink in a crossover pattern (1-4). Ê Carefully turn the heat sink back and forth to detach it from the processor. This may be necessary due to the adhesive quality of the thermal paste located between the heat sink and processor.
Page 226: Removing The Processor
Processors 11.2.3 Removing the processor Figure 121: Unlatching the socket lever Ê Unlatch the socket lever by pushing it down and away from the socket (1). Ê Fold back the socket release lever (2). Figure 122: Removing the processor Ê Rotate the socket lever to lift the load plate away from the socket (1). Upgrade and Maintenance Manual TX1320 M1...
Page 227: Installing The Processor
Processors Ê Make sure that the load plate is in the fully open position. Ê Carefully remove the defective processor from its socket in a vertical motion (2). CAUTION! Be careful not to touch or bend the spring contacts on the processor socket.
Page 228 Processors Figure 124: Closing the load plate (A) Ê Lower the load plate over the processor while leaving the socket lever in the open position. Figure 125: Closing the load plate (B) Ê Lower the socket lever while making sure that the front edge of the load plate slides under the shoulder screw cap (see close-up) as the lever is lowered.
Page 229: Applying Thermal Paste
Processors Figure 126: Latching the socket lever Ê Latch the socket lever under the load plate tab. 11.2.5 Applying thermal paste For the Japanese market, the service engineer must follow the instruction provided separately. If the processor upgrade or replacement kit contains a new CPU heat sink, a thin layer of thermal compound has already been pre-applied to its lower surface.
Page 230 Processors Figure 127: Thermal paste syringe One thermal compound syringe (FTS-FSP:P304000004) contains thermal paste for three processors. In order to determine the correct amount of thermal paste (equal to 1.0 gram), divide the grey area of the syringe up into three equal segments. Add graduation marks to the syringe using a permanent marker to help you apply the thermal paste.
Page 231: Installing The Processor Heat Sink
Processors Figure 128: Applying thermal paste Ê Apply a small point-shaped amount of thermal paste (1.0 gram, see description above) to the center of the processor surface as shown. CAUTION! Do not mix different types of thermal paste. 11.2.6 Installing the processor heat sink Figure 129: Installing the heat sink (A) Ê...
Page 232 Processors CAUTION! – Ensure that the screws on the heat sink are properly seated on the threaded holes. – Ensure that the heat sink cooling fins match the direction of the airflow! Figure 130: Installing the heat sink (B) Ê Fasten the four captive screws on the heat sink in a crossover pattern (screw torque: 0.6 Nm, not applicable for the Japanese market) (1-4).
Page 233: Concluding Steps
Processors Figure 131: Installing the heat sink (B) Ê Connect the CPU fan cable to the FAN1 SYS connector on the system board. 11.2.7 Concluding steps "Installing the system fan module" on page 156 Ê "Closing the server" on page 64 Ê...
Page 234: Replacing The Processor Heat Sink
Processors 11.3 Replacing the processor heat sink Field Replaceable Unit Hardware: 15 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 11.3.1 Preliminary steps "Locating the defective server" on page 44 Ê "Shutting down the server" on page 52 Ê...
Page 235: Accessible Drives
Accessible drives This chapter provides information on how to install, remove or replace SATA optical disk drives and USB backup drives. Safety notes CAUTION! Before installing an accessible drive, acquaint yourself with the ● drive's user documentation. When inserting an accessible drive into the server, ensure not to ●...
Page 236: Basic Procedure
Accessible drives 12.1 Basic procedure Mounting order for accessible drives PRIMERGY TX1320 M1 server offers a 5.25-inch slimline SATA optical drive bay and 2.5-inch USB backup drive bay: Figure 132: Accessible drives mounting order Accessible drive Max. # 3.5-inch bay 5.25-inch bay2...
Page 237: Optical Disk Drive (Odd)
Accessible drives 12.2 Optical disk drive (ODD) 12.2.1 Installing optical disk drive (ODD) Upgrade and Repair Unit Hardware: 10 minutes (URU) Preliminary and concluding steps: Slotted screw driver (only for Tools: removing the optical disk drive filler cover Installing accessible drives: tool-less 12.2.1.1 Preliminary steps Before installing an accessible drive, perform the following steps: Ê...
Page 238: Removing The Optical Disk Drive Filler Cover
Accessible drives 12.2.1.2 Removing the optical disk drive filler cover Figure 133: Removing the ODD filler cover Ê Using a slotted screw driver, pry the ODD filler cover out of its bay and remove it from its installation bay. CAUTION! Save the ODD filler cover for future use.
Page 239 Accessible drives Figure 134: Removing the ODD installation bracket Ê Slide the ODD installation bracket out of the ODD installation bay. Upgrade and Maintenance Manual TX1320 M1...
Page 240: Installing The Optical Disk Drive
Accessible drives 12.2.1.3 Installing the optical disk drive Figure 135: Installing the optical disk drive Ê Attach the installation bracket to the optical drive as shown. Upgrade and Maintenance Manual TX1320 M1...
Page 241 Accessible drives Figure 136: Installing the optical disk drive Ê Ensure that the hooks on the installation bracket properly engage with the screw holes on the optical drive (see circles). Upgrade and Maintenance Manual TX1320 M1...
Page 242 Accessible drives Figure 137: Installing the optical disk drive Ê Insert the optical disk drive into its installation bay and carefully push in until it locks in place. Upgrade and Maintenance Manual TX1320 M1...
Page 243 Accessible drives Figure 138: Connecting cables to the optical disk drive Ê Connect cables to the optical disk drive. SATA cable Y3928-V205 Power cable Y4012-V501 connector P5 Upgrade and Maintenance Manual TX1320 M1...
Page 244: Concluding Steps
Accessible drives Figure 139: Routing cables Ê Run the SATA ODD cable Y3928-V205 through the cable clamps (see circle) as shown. Ê Ensure that the SATA ODD cable is connected to system board connector SATA 5. 12.2.1.4 Concluding steps Perform the following procedures to complete the task: Ê...
Page 245: Removing An Optical Disk Drive (Odd)
Accessible drives 12.2.2 Removing an optical disk drive (ODD) Field Replaceable Unit Hardware: 10 minutes (FRU) Preliminary and concluding steps: Slotted screw driver (only for Tools: removing the optical disk drive filler cover) Installing accessible drives: tool-less 12.2.2.1 Preliminary steps Before installing an accessible drive, perform the following steps: Ê...
Page 246: Removing An Optical Disk Drive
Accessible drives 12.2.2.2 Removing an optical disk drive Figure 140: Disconnecting cables from the optical disk drive Ê Disconnect all cables from the optical disk drive. SATA cable Y3928-V205 Power cable Y4012-V501 connector P5 Upgrade and Maintenance Manual TX1320 M1...
Page 247 Accessible drives Figure 141: Unlocking the optical disk drive Ê Press the green touch point to disengage the optical disk drive. Upgrade and Maintenance Manual TX1320 M1...
Page 248 Accessible drives Figure 142: Removing the optical disk drive Ê Pull the optical disk drive out of its bay. Figure 143: Inserting the installation bracket Ê Insert he installation bracket into the 5.25 installation bay. Upgrade and Maintenance Manual TX1320 M1...
Page 249: Concluding Steps
Accessible drives Figure 144: Inserting the ODD filler cover. Ê Insert the ODD filler cover into the recess on the right side (1). Ê Fold the ODD filler cover back (2). 12.2.2.3 Concluding steps Perform the following procedures to complete the task: Ê...
Page 250: Replacing An Optical Disk Drive (Odd)
Accessible drives 12.2.3 Replacing an optical disk drive (ODD) Field Replaceable Unit Hardware: 15 minutes (FRU) Preliminary and concluding steps: Slotted screw driver (only for Tools: removing the optical disk drive filler cover) Installing accessible drives: tool-less 12.2.3.1 Preliminary steps Before installing an accessible drive, perform the following steps: Ê...
Page 251: Concluding Steps
Accessible drives Figure 145: Removing the installation bracket Ê Remove installation bracket. Ê Install the replacement ODD as described in section "Installing optical disk drive (ODD)" on page 237. 12.2.3.3 Concluding steps Perform the following procedures to complete the task: Ê...
Page 252: Backup Drive
Accessible drives 12.3 Backup drive 12.3.1 Installing backup drive Upgrade and Repair Unit Hardware: 10minutes (URU) Preliminary and concluding steps: tool-less Tools: Removing accessible drives: Phillips PH2 / (+) No. 2 screw driver 12.3.1.1 Preliminary steps Before installing an accessible drive, perform the following steps: Ê...
Page 253 Accessible drives Figure 146: Removing the dummy cover Ê Disengage the hooks of the dummy cover on the internal side of the side / top cover (1). Ê Remove the dummy cover outward from the front of the side / top cover in the direction of the arrow (2).
Page 254: Removing The Backup Drive Filler Cover
Accessible drives 12.3.1.3 Removing the backup drive filler cover Figure 147: Removing the backup drive filler cover Ê Hold the backup drive filler cover by its two handle recesses (1) and pull it out of the installation bay (2). CAUTION! Save the backup drive filler cover for future use.
Page 255: Installing The Backup Drive
Accessible drives 12.3.1.4 Installing the backup drive Figure 148: Installing the backup drive Ê Insert the backup drive into its installation bay. Ê Carefully push back until the backup drive cover plate is flush with the front panel. Figure 149: Inserting the screw Upgrade and Maintenance Manual TX1320 M1...
Page 256 Accessible drives Ê Secure the backup drive to the drive cage with one screw (M3 x 4.5 mm). Use the screw hole marked "1st". Ê Open the front cage as described in section "Opening the front cage" on page Figure 150: Connecting cables to the backup drive Ê...
Page 257: Concluding Steps
Accessible drives 12.3.1.5 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in "Closing the front cage" on page Ê Close the server cover as described in section "Closing the server" on page Ê...
Page 258: Removing The Backup Drive
Accessible drives 12.3.2.2 Removing the backup drive Figure 151: Disconnecting cables from the backup drive Ê Disconnect all cables from the backup drive. USB cable Y3973-V91 Type B connector (1) SATA power cable T26139-Y4012-V501 connector P2 (2) Ê Remove the SATA power cable from the cable clamps (see circle) and (see circle).
Page 259 Accessible drives Figure 152: Removing screw from the backup drive Ê Remove the screw. Figure 153: Removing the backup drive Ê Pull the backup drive out of its bay. Upgrade and Maintenance Manual TX1320 M1...
Page 260: Inserting The Backup Drive Filler
Accessible drives 12.3.2.3 Inserting the backup drive filler Figure 154: Inserting the backup drive filler cover Ê Insert the backup drive filler cover. 12.3.2.4 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in "Closing the front cage"...
Page 261: Replacing A Backup Drive
Accessible drives 12.3.3 Replacing a backup drive Field Replaceable Unit Hardware: 10minutes (FRU) Preliminary and concluding steps: tool-less Tools: Removing accessible drives: Phillips PH2 / (+) No. 2 screw driver 12.3.3.1 Preliminary steps Before installing an accessible drive, perform the following steps: Ê...
Page 262: Concluding Steps
Accessible drives 12.3.3.3 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in "Closing the front cage" on page Ê Close the server cover as described in section "Closing the server" on page Ê...
Page 263: Hdd Expansion Box
Accessible drives 12.4 HDD expansion box 12.4.1 Installing a HDD expansion box Upgrade and Repair Unit Hardware: 10 minutes (URU) Preliminary and concluding steps: tool-less Tools: Removing accessible drives: Phillips PH2 / (+) No. 2 screw driv 12.4.1.1 Preliminary steps Before installing an accessible drive, perform the following steps: Ê...
Page 264: Removing The Backup Drive Filler Cover
Accessible drives 12.4.1.2 Removing the backup drive filler cover Figure 155: Removing the backup drive filler cover Ê Hold the backup drive filler cover by its two handle recesses (1) and pull it out of the installation bay (2). CAUTION! Save the backup drive filler cover for future use.
Page 265: Installing The Hdd Expansion Box
Accessible drives 12.4.1.3 Installing the HDD expansion box Figure 156: Installing the HDD expansion box Ê Insert the backup drive into its installation bay. Ê Carefully push back until the backup drive cover plate is flush with the front panel. Figure 157: Installing the HDD expansion box Ê...
Page 266: Concluding Steps
Accessible drives Ê Use the screw hole marked “1st”. Figure 158: Installing the HDD expansion box Ê Connect the SATA cable to the HDD expansion box connector (1). Ê Connect the power connector P2 on SATA power cable T26139-Y4012- V501 to the HDD expansion box (2). Ê...
Page 267: Removing A Hdd Expansion Box
Accessible drives Ê Reconnect the AC power cord to the power supply unit. Ê If BitLocker functionality is used and has been disabled before starting the maintenance task, re-enable BitLocker as described in section "Enabling BitLocker functionality" on page Ê Verify if your backup software solution requires additional configuration after installing, removing or replacing an accessible drive as described in section "Verifying and configuring the backup software solution"...
Page 268: Removing The Hdd Expansion Box
Accessible drives 12.4.2.2 Removing the HDD expansion box Figure 159: Removing the HDD expansion box Ê Disconnect the SATA cable from the HDD expansion box connector (1). Ê Disconnect the power connector P2 on SATA power cable T26139-Y4012- V501 from the HDD expansion box (2). Ê...
Page 269 Accessible drives Figure 160: Screw of the HDD expansion box Ê Loosen the screw of the HDD extension box from the drive cage. Figure 161: Removing the HDD expansion box Ê Remove the HDD expansion box from its installation bay. Upgrade and Maintenance Manual TX1320 M1...
Page 270: Inserting The Backup Drive Filler
Accessible drives 12.4.2.3 Inserting the backup drive filler Figure 162: Inserting the backup drive filler cover Ê Insert the backup drive filler cover. 12.4.2.4 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in "Closing the front cage"...
Page 271: Replacing A Hdd Expansion Box
Accessible drives 12.4.3 Replacing a HDD expansion box Upgrade and Repair Unit Hardware: 10 minutes (URU) Preliminary and concluding steps: tool-less Tools: Removing accessible drives: Phillips PH2 / (+) No. 2 screw driv 12.4.3.1 Preliminary steps Before installing an accessible drive, perform the following steps: Ê...
Page 272: Concluding Steps
Accessible drives 12.4.3.3 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in "Closing the front cage" on page Ê Close the server cover as described in section "Closing the server" on page Ê...
Page 273: Front Panel
Front panel This chapter provides information on how to replace the front panel module and optional front LAN connector board. Safety notes CAUTION! When inserting the front panel module into the server, ensure not to ● pinch or strain any connected cables. Circuit boards and soldered parts of internal options are exposed and ●...
Page 274: Replacing The Front Panel Module
Front panel 13.1 Replacing the front panel module Field Replaceable Units (FRU) Average hardware task duration: 10 minutes Average software task duration: 5 minutes Note on system information backup / restore The front panel module contains the Chassis ID EPROM that contains system information like server name and model, housing type, serial number and manufacturing data.
Page 275: Removing The Front Panel Module
Front panel Ê Disable boot watchdog functionality as described in section "Disabling SVOM boot watchdog functionality" on page Ê Locate the defective server as described in section "Locating the defective server" on page Ê Shut down the server as described in section "Shutting down the server"...
Page 276 Front panel Figure 164: Removing the front panel module Ê Disconnect the front panel cable from the front panel module (1). Ê Disengage the retention hooks of the front panel module (2). Ê Remove the defective front panel module. Ê Fold down the front cage. Upgrade and Maintenance Manual TX1320 M1...
Page 277: Installing The Front Panel Module
Front panel 13.1.4 Installing the front panel module Figure 165: Inserting the front panel module Ê Insert the new front panel module as shown and carefully push in until it locks in place. Ê Open the front cage. Upgrade and Maintenance Manual TX1320 M1...
Page 278 Front panel Figure 166: Connecting the front panel cable to the front panel module Ê Connect the front panel cable to the front panel module. Figure 167: Connecting the front panel cable to the system board Ê Connect the front panel cable Y4015-V4 to the system board connector FRONTPANEL.
Page 279: Concluding Steps
Front panel 13.1.5 Concluding steps Perform the following procedures to complete the task: Ê Close the front cage as described in section "Closing the front cage" on page Ê Close the server cover as described in section "Closing the server" on page Ê...
Page 280 Front panel Upgrade and Maintenance Manual TX1320 M1...
Page 281: System Board And Components
System board and components This chapter provides information on how to replace the system board and system board components as its CMOS battery, the USB Flash Module (UFM) and the Trusted Platform Module (TPM). Safety notes CAUTION! Devices and components inside the server remain hot after ●...
Page 282: Basic Information
System board and components 14.1 Basic information This section provides instructions for the system board and the following components: CMOS battery ● CMOS memory (volatile BIOS memory) and the real-time clock are powered by a lithium coin cell (CMOS battery). This cell lasts up to ten years, depending on ambient temperature and use.
Page 283: Preliminary Steps
System board and components Do not throw batteries into the trash can. Lithium batteries must be ● disposed of in accordance with local regulations concerning special waste. For further safety information, please refer to section "Environmental ● protection" in the operating manual of your server. Ensure to insert the CMOS battery the with the positive pole ●...
Page 284 System board and components Ê Press out on the locking spring to eject the depleted CMOS battery (1). Ê If the CMOS battery cannot be ejected this way, use a toothpick (recommended) or similar tool as a lever: Insert the toothpick between the battery and locking spring as shown (2).
Page 285: Concluding Steps
System board and components Ê Fold down the CMOS battery (2) until it locks in place. Ê Ensure that the locking spring (3) is properly engaged. 14.2.3 Concluding steps Ê Dispose of the CMOS battery in accordance with local regulations concerning special waste.
Page 286: Installing The Ufm
System board and components 14.3.1.2 Installing the UFM Figure 170: UFM kit USB Flash Module (UFM) UFM spacer UFM nylon screw Figure 171: UFM mounting location Figure 172: Installing the UFM Upgrade and Maintenance Manual TX1320 M1...
Page 287: Concluding Steps
System board and components Ê Connect the UFM to the system board, snapping in the UFM spacer. 14.3.1.3 Concluding steps "Closing the server" on page 64 Ê "Connecting the server to the mains" on page 67 Ê "Switching on the server" on page 71 Ê...
Page 288: Software Configuration
System board and components 14.3.1.4 Software configuration The UFM delivery set includes the "Recovery Tool CD" to setup the ESXi configuration. Proceed as follows: Ê Switch on the server. Ê Right after switching on the server, insert the "Recovery Tool CD" into the DVD drive and close the drive tray.
Page 289: Removing The Ufm
System board and components 14.3.2.2 Removing the UFM Figure 173: Removing the UFM (A) Ê Remove the nylon screw (1). Ê Disconnect and remove the UFM (2). Figure 174: Removing the UFM (B) Ê The UFM spacer remains on the system board. 14.3.2.3 Concluding steps "Closing the server"...
Page 290: Replacing The Ufm
System board and components 14.3.3 Replacing the UFM Field Replaceable Unit Hardware: 10 minutes (FRU) Software: 5 minutes Tools: – Phillips PH1 / (+) No. 1 screw driver – combination pliers and flat nose pliers 14.3.3.1 Preliminary steps "Disabling BitLocker functionality" on page 73 Ê...
Page 291: Installing The New Ufm
System board and components 14.3.3.3 Installing the new UFM Figure 175: Preparing the new UFM Ê Remove the nylon screw from the new UFM (1). Ê Remove the UFM spacer (2). Figure 176: Installing the UFM Ê Fit the UFM on the UFM connector and the remaining UFM spacer (1). Ê...
Page 292: Concluding Steps
System board and components Destroying the defective UFM CAUTION! The UFM contains customer information (e.g. IP address, license numbers). After replacing the UFM, hand the defective UFM over to the customer. If the customer requests disposal of the defective UFM, proceed as follows: Figure 177: Destroying the defective UFM Ê...
Page 293: Software Configuration
System board and components 14.3.3.5 Software configuration The UFM delivery set includes the "Recovery Tool CD" to setup the ESXi configuration. Proceed as follows: Ê Switch on the server. Ê Right after switching on the server, insert the "Recovery Tool CD" into the DVD drive and close the drive tray.
Page 294: Installing The Tpm
System board and components 14.4.1.2 Installing the TPM Figure 178: TPM kit TPM (Trusted Platform Module) Special screw for TPM TPM spacer TPM bit insert for TPM special screw The black TPM spacer is not used in this server. Figure 179: TPM mounting location Figure 180: Installing the TPM spacer Ê...
Page 295 System board and components Figure 181: Installing the TPM Ê Connect the TPM to the system board. Figure 182: TPM bit insert Ê Attach the TPM bit insert or TPM module fixing tool (Japanese market) to a bit screw driver. Upgrade and Maintenance Manual TX1320 M1...
Page 296: Concluding Steps
System board and components Figure 183: Securing the TPM Ê Secure the TPM with the TPM screw using the TPM bit insert. Do not fasten the screw too firmly. Stop as soon as the head of the screw lightly touches the TPM. 14.4.1.3 Concluding steps "Closing the server"...
Page 297: Removing The Tpm
System board and components 14.4.2 Removing the TPM Field Replaceable Unit Hardware: 30 minutes (FRU) Tools: Removing the system board: – Phillips PH2 / (+) No. 2 screw driver Installing the TPM: – Bit screw driver – TPM bit insert For the Japanese market: –...
Page 298: Removing The Tpm
For further information on how to disable BitLocker drive encryption, please refer to the Microsoft Knowledge Base. Fujitsu service partners will find additional information (also available in Japanese) on the Fujitsu Extranet web pages. Ê Disable TPM in the system board BIOS. Proceed as follows: Ê...
Page 299 System board and components Figure 184: Removing the TPM screw Ê Locate the slotted lower end of the TPM screw (1). Ê Carefully loosen the TPM screw using a thin slotted screw driver (e.g. watchmaker's screw driver) or the dedicated TPM screw driver (Japanese market) (2).
Page 300: Concluding Steps
System board and components Figure 185: Removing the TPM spacer Ê Using a small pair of combination pliers, press together the hooks on the TPM spacer (1, see close-up) and remove it from the system board (2). If the TPM is to be replaced, the TPM spacer may remain on the system board.
Page 301: Replacing The Tpm
System board and components 14.4.3 Replacing the TPM Field Replaceable Unit Hardware: 40 minutes (FRU) Tools: Removing the system board: – Phillips PH2 / (+) No. 2 screw driver Replacing the TPM: – Bit screw driver – TPM bit insert –...
Page 302: Removing The Defective Tpm
System board and components 14.4.3.2 Removing the defective TPM Ê Remove the TPM as described in section "Removing the TPM" on page 297. Ê Leave the TPM spacer on the system board when removing the defective TPM. 14.4.3.3 Installing the new TPM Ê...
Page 303: Replacing The System Board
System board and components 14.5 Replacing the system board Field Replaceable Unit Hardware: 50 minutes (FRU) Software: 10 minutes Tools: Replacing the system board: – Phillips PH2 / (+) No. 2 screw driver – Magnifying glass for inspecting processor socket springs (recommended) Replacing the TPM: –...
Page 304 System board and components – If the customer is using TPM functionality, remove the TPM from the old system board and install it on the new system board. Advise your contact persons that they must provide you with TPM backup copies. For security reasons, the TPM must be restored / re- saved by the customer.
Page 305: Preliminary Steps
System board and components 14.5.1 Preliminary steps "Disabling BitLocker functionality" on page 73 Ê "Disabling SVOM boot watchdog functionality" on page 74 Ê "Locating the defective server" on page 44 Ê "Shutting down the server" on page 52 Ê "Disconnecting power cords" on page 53 Ê...
Page 306 System board and components Figure 186: Screws system board Ê Remove eight screws from the system board (see circles). Upgrade and Maintenance Manual TX1320 M1...
Page 307 System board and components Figure 187: Detaching the system board Ê Slightly lift up the system board by the memory module ejectors and a PCI slot (1) in order to detach it from the centering bolts (C). Ê Carefully shift the system board towards the server front until the plug shells disengage from the cut-outs in the connector panel (2).
Page 308 System board and components Figure 188: Removing the system board Ê Hold the defective system board by the memory module ejectors and a PCI slot and at a slight angle lift it out of the chassis. Ê If applicable, remove the TPM as described in section "Removing the TPM"...
Page 309: Installing The New System Board
System board and components 14.5.3 Installing the new system board Figure 190: Installing the system board (A) Ê Hold the system board by the memory module ejectors and a PCI slot. CAUTION! – Do not lift or handle the system board by any of its heat sinks! –...
Page 310 System board and components Figure 191: Installing the system board (B) Ê Carefully shift the system board towards the server rear until the plug shells engage with the cut-outs in the connector panel. Ê Lower the system board onto the centering bolts (C). Ensure that the system board is properly seated on both centering bolts.
Page 311: Swapping The Processor
System board and components Figure 192: Installing the power cable clamp Ê Press down on the power cable clamp until it snaps into place. Ê Verify the settings on the new system board (see section "Onboard settings" on page 327). 14.5.4 Swapping the processor Figure 193: Unlatching the socket lever (new system board) Ê...
Page 312 System board and components Ê Fold back the socket lever to disengage the load plate (2). Ê Rotate the socket lever to lift the load plate. Ê Make sure that the load plate is in the fully open position. Figure 194: Removing the protective socket cover (new system board) Ê...
Page 313 System board and components Ê Carefully remove the processor from its socket on the defective system board as described in section "Removing the processor" on page 226. Ê Install the processor on the new system board as described in section "Installing the processor"...
Page 314 System board and components Figure 196: Installing the protective socket cover (defective system board) (B) Ê Lower the load plate over the processor while leaving the socket lever in the open position. Ê Lower the socket lever while making sure that the front edge of the load plate slides under the shoulder screw cap (see close-up) as the lever is lowered.
Page 315: Concluding Steps
System board and components 14.5.5 Concluding steps Ê Reconnect all cables to the system board. For a complete cabling overview, please refer to section "Cabling" on page 319. Ê Reinstall all remaining system board components as shown in the related sections: –...
Page 316 System board and components "Verifying the system time settings" on page 95 Ê "Looking up changed MAC / WWN addresses" on page 100 Ê "Updating the NIC configuration file in a Linux environment" on page 97 Ê "Enabling SVOM boot watchdog functionality" on page 92 Ê...
Page 317: Cables
Cables This chapter provides information on how to connect, disconnect and route cables. Safety notes CAUTION! Always hold cables by their connectors when disconnecting them. ● Never pull on the cable to disconnect cables. Ensure that none of the cables are scraped, strained or otherwise ●...
Page 318: Cabling Overview
Cables 15.1 Cabling overview 15.1.1 Overview of used cables Name Number Routing 2.5" 3.5" model model Front panel from front panel connector / USB 3.0 T26139-Y4015-V4 module to system cable board T26139-Y4012- from all drives to Power cable V501 system board T26139-Y3928- V205 from optical disk drive...
Page 319: Cabling
Cables 15.2 Cabling Figure 198: Cabling 2x 3.5-inch HDD (LFF) Figure 199: Cabling 4x 2.5-inch HDD (SFF) Upgrade and Maintenance Manual TX1320 M1...
Page 320 Cables Figure 200: Cabling with extension box Upgrade and Maintenance Manual TX1320 M1...
Page 321: Appendix
Appendix 16.1 Mechanical overview 16.1.1 Server front 2.5-inch HDD model Figure 201: PRIMERGY TX1320 M1 front - 2.5-inch HDD model Pos. Component Reference 2.5-inch hard disk drives / "Mounting order for 2.5-inch HDDs / dummy modules SSDs" on page 117...
Page 322: Server Rear
Appendix 16.1.2 Server rear Figure 202: PRIMERGY TX1320 M1 rear Pos. Component Reference Standard power supply "Replacing the standard power supply unit" unit on page 108 CSS / Global Error / ID "I/O panel indicators" on page 332 indicators Serial connector...
Page 323: Server Interior
Appendix 16.1.3 Server interior Figure 203: PRIMERGY TX1320 M1 interior (2.5-inch HDD / standard PSU model) Pos. Component Reference System fan "Replacing the system fan module" on page 152 Expansion card slots "Replacing expansion cards" on page 181 Processor / CPU heat "Upgrading or replacing the processor"...
Page 324: Configuration Tables
Appendix Pos. Component Reference Front panel module bay "Replacing expansion cards" on page 181 Accessible drive bay "Replacing the system fan module" on page 152 System board D3239 "Replacing the system board" on page 303 Memory modules "Replacing memory modules" on page 221 Standard power supply "Replacing the standard power supply unit"...
Page 325: Connectors And Indicators
Appendix 16.3 Connectors and indicators 16.3.1 Connectors and indicators on the system board 16.3.1.1 Onboard connectors FAN4SYS DIMM1B DIMM2B COM1 DIMM1A DIMM2A SATA POWER Service Management LAN/ USB 9/10 Intel FAN1 Shared LAN/ USB 7/8 i210 Standard LAN/ Intel USB 5/6 i217 FAN2SYS SATA1-4...
Page 326 Appendix No. Print Description PWR1 ATX power supply connector FAN4 SYS Connector for system fan Power distribution for SAS / SATA backplanes and SATA POWER accessible drives PC2009 Power management connector FRONTPANEL Front panel Power supply connector USB FRONT Connector for front USB FAN3 SYS Connector for system fan FAN1 SYS...
Page 327: Onboard Settings
Appendix 16.3.1.2 Onboard settings Default RCVR Slot 3 PCIe x8 Battery Slot 2 PCIe x4 Jumper SATA6 SATA5 Slot 1 PCIe x1 HDD ACTIVITY Figure 205: Jumper Setting Description Default Password skip disabled and recovery BIOS disabled RCVR Recovery BIOS enabled When the recovery BIOS is applied on a system board, the password set by customers disappears from system board.
Page 328: Onboard Indicators And Controls
Appendix 16.3.1.3 Onboard indicators and controls FAN4SYS DIMM1B DIMM2B COM1 DIMM1A DIMM2A SATA POWER Service Management LAN/ USB 9/10 Intel FAN1 Shared LAN/ USB 7/8 i210 Standard LAN/ Intel USB 5/6 i217 FAN2SYS SATA1-4 Micro Slot 4 PCIe x8 Indicate USB1AUX iRMC S4 Intel...
Page 329 Appendix Indicator Status Description no critical event (non CSS component) orange on prefailure detected (non CSS component) non CSS component failure Possible reasons: (Global Error orange LED) – sensors report overheating flashing – sensor is defective – CPU error – software reports an error no critical event (CSS component) yellow on prefailure detected (CSS component)
Page 330 Appendix Using the Indicate CSS button Ê Shut down and power off the server. Ê Disconnect the AC power cord from the system. It is mandatory to disconnect power cords in order to use the Indicate CSS functionality. Ê Press the Indicate CSS button to highlight defective components. Component LEDs LEDs A, B and C are visible from the outside on the server rear.
Page 331: I/O Panel Connectors
Appendix Indicator Status Description PCI card operational PCI card orange on PCI card failure AUX power yellow on AUX voltages are within range green iRMC S4 management controller is iRMC flashing operational 16.3.1.4 I/O panel connectors 1 Management LAN connector, for iRMC S4 server management function 2 Shared LAN connector (LAN1) 3 Standard LAN connector (LAN2) 4 USB 3.0 connectors...
Page 332: I/O Panel Indicators
Depending on BIOS settings, the shared LAN connector may also be used as a management LAN connector. For further information, please refer to the "D3239 BIOS Setup Utility for FUJITSU Server PRIMERGY TX1320 M1 S3 Reference Manual". The serial connector COM1 can be used as default interface or to communicate with the iRMC S4.
Page 333 Appendix Note on the onboard LAN controller The system board is equipped with a Gigabit Ethernet Controller that supports transfer rates of 10 Mbit/s, 100 Mbit/s and 1 Gbit/s. The separate management LAN connector is used as a management interface (iRMC S4) and is prepared for operation with the Remote Management.
Page 334 Appendix Figure 208: Indicators on the connector panel: CSS, Global Error and ID indicators Indicator Status Description no critical event (non CSS component) prefailure detected (non CSS Global error orange on component) indicator orange non CSS component failure flashing no critical event (CSS component) yellow on prefailure detected (CSS component) CSS indicator...
Page 335: Connectors And Indicators On The Front Panel
Appendix 16.3.2 Connectors and indicators on the front panel 16.3.2.1 Front panel controls and indicators Figure 209: Front side (indicators and controls) Local diagnostic indicators Pos. Indicator Status Description HDD error HDD / SSD, SAS / SATA backplane or yellow on indicator RAID controller failure detected PSU error...
Page 336 Appendix In addition to local diagnostic indicators, CSS or Global Error LEDs indicate, if the defective component is a customer replaceable unit or if a service technician needs to be dispatched to replace the part. Status indicators Pos. Indicator Status Description blue on Localizes the server...
Page 337 Appendix Pos. Indicator Status Description iRMC booting After connecting the server to the mains (power cord plugged in / yellow / after mains failure) the iRMC will orange boot. The system cannot be flashing switched on, until the iRMC boot sequence is complete.
Page 338 Appendix Buttons Pos. Button Function This button highlights the ID indicator on the front and ID button I/O panels for easy server identification. This button is used to reboot the system. It can be pressed using the end of a paper clip. Reset button CAUTION! Risk of data loss!
Page 339: Minimum Startup Configuration
Appendix 16.4 Minimum startup configuration Field Replaceable Units (FRU) If the server does not start up or other problems occur, it may be necessary to take the system down to its most basic configuration in order to isolate the defective component. The minimum startup configuration consists of the following components and cables: Component...
Page 340 Appendix Ê Connect a keyboard, mouse and display to the server. Ê Switch on the server as described in section "Switching on the server" on page CAUTION! Since the fan module is not included in the minimum startup configuration, the server must be shut down immediately after the diagnostic process is complete (POST phase has been passed).

Fujitsu PRIMERGY TX1320 M1 Upgrade And Maintenance Manual

1 Introduction

2 Before You Start

3 Important Information

4 Basic Hardware Procedures

5 Basic Software Procedures

6 Power Supply

7 Hard Disk Drives / Solid State Drives

8 System Fan and HDD Fan

9 Expansion Cards and Backup Units

10 Main Memory

11 Processors

12 Accessible Drives

13 Front Panel

Quick Links

Related Manuals for Fujitsu PRIMERGY TX1320 M1

Summary of Contents for Fujitsu PRIMERGY TX1320 M1