Page 1 Upgrade and Maintenance Manual - English FUJITSU Server PRIMERGY TX1320 M4 Upgrade and Maintenance Manual August 2019...
Page 2 – The contents of this manual may be revised without prior notice. – Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. – No part of this manual may be reproduced in any form without the prior written permission of Fujitsu.
Page 3 Before reading this manual For your safety This manual contains important information for safely and correctly using this product. Carefully read the manual before using this product. Pay particular attention to the accompanying manual "Safety Notes and Regulations" and ensure that these safety notes are understood before using the product.
Page 4 Please consult the sales staff of Fujitsu if intending to use this product for high safety use. Measures against momentary voltage drop This product may be affected by a momentary voltage drop in the power supply caused by lightning.
Page 5 HDD used. For more information on the usage and operation conditions of each available type of HDD, see the following internet address: http://jp.fujitsu.com/platform/server/primergy/harddisk/ Only for Japan: Shielded LAN cables should be used in this product.
Page 6 Version History Issue number Reason for update 1.0 / November 2018 Initial release 2.0 / August 2019 New text Chassis ID Prom Tool, new CPU types Upgrade and Maintenance Manual TX1320 M4...
Page 7: Table Of Contents
Contents Introduction ......21 Notational conventions ....22 Before you start .
Page 8 Contents Getting access to the component ....51 4.4.1 Removing the server cover ....52 4.4.2 Removing the accessible drive bay cover .
Page 9 Contents 5.2.10 Verifying the memory mode ....82 5.2.11 Verifying the system time settings ....83 5.2.12 Viewing and clearing the System Event Log (SEL) .
Page 10 Concluding steps ..... . 116 Fujitsu battery unit (FJBU) ....117 6.4.1...
Page 11 Contents Hard disk drives (HDD) and solid state drives (SSD) ..129 Basic information ..... . . 130 Handling HDDs or SSDs without installation frame .
Page 12 Contents 7.4.7 Replacing a 2.5-inch backplane ....151 7.4.7.1 Preliminary steps ..... . 151 7.4.7.2 Removing a 2.5-inch HDD/PCIe backplane .
Page 13 Contents Basic information ..... . . 172 Handling slot brackets ..... 173 9.2.1 Installing a slot bracket .
Page 14 Contents 9.5.2 Removing an FBU ..... . . 202 9.5.2.1 Preliminary steps ..... . 202 9.5.2.2 Removing the FBU from the tray .
Page 15 Contents 11.2.3 Removing the heat sink variant 2 ....220 11.2.4 Removing the CPU ..... . . 221 11.2.5 Installing the CPU .
Page 16 Contents 12.3 Backup drive (RDX) ..... . 251 12.3.1 Installing the RDX drive ..... 251 12.3.1.1 Preliminary steps .
Page 17 Contents 13.2.3 Replacing a front USB connector ....270 13.2.3.1 Preliminary steps ..... . . 270 13.2.3.2 Removing the front USB connector .
Page 18 Contents 14.4.3 Replacing the iRMC microSD card ....287 14.4.3.1 Preliminary steps ..... . 287 14.4.3.2 Replacing the iRMC microSD card .
Page 19 Contents 14.7 System board ......304 14.7.1 Replacing the system board ....304 14.7.1.1 Preliminary steps .
Page 20 Contents Upgrade and Maintenance Manual TX1320 M4...
Page 21: Introduction
Introduction This Upgrade and Maintenance Manual provides instructions for the following procedures: Upgrading the server configuration by adding optional hardware ● components Upgrading the server configuration by replacing existing hardware ● components with superior ones. Replacing defective hardware components ● This manual focuses on on-site maintenance tasks.
Page 22: Notational Conventions
Introduction Notational conventions The following notational conventions are used in this manual: Text in bold Indicates references to names of interface elements. Indicates commands and text to be entered by the user. Text in monospace "Quotation marks" Indicate names of chapters and terms that are being emphasized.
Page 23: Before You Start
The operating manual of your server gives an introduction to server features and provides an overview of available hardware options. Use the Fujitsu ServerView Suite management software and the iRMC web interface to prepare hardware expansions. ServerView Suite documentation is available online at http://manuals.ts.fujitsu.com.
Page 24 For Japan: http://www.fujitsu.com/jp/products/computing/servers/primergy/ Please contact your local Fujitsu customer service partner for details on how to order expansion kits or spare parts. Replacing a defective component The Global Error indicator on the front of the server reports defective hardware components that need to be replaced.
Page 25: Classification Of Procedures
At the beginning of each procedure, the involved unit type is indicated by one of the symbols introduced in this section. Please ask your local Fujitsu service center for more information. 2.1.1 Customer Replaceable Units (CRU)
Page 26: Upgrade And Repair Units (Uru)
(Repair Units). For Japan, customer allows only upgrade. For upgrade units as customer replaceable, see: http://www.fujitsu.com/jp/products/computing/servers/primergy/ Server management error messages and diagnostic indicators on the front panel and system board will report defective Upgrade and Repair Units as customer replaceable CSS components.
Page 27: Field Replaceable Units (Fru)
Maintenance procedures involving Field Replaceable Units must be performed exclusively by Fujitsu service personnel or technicians trained by Fujitsu. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. Components that are handled as Field Replaceable Units –...
Page 28: Average Task Duration
Before you start Average task duration Hardware: 10 minutes The average task duration including preliminary and concluding steps is indicated at the beginning of each procedure next to the procedure class. See the following table for an overview of steps taken into account for calculating the average task duration: Step included...
Page 29: Tools You Need At Hand
"Safety Notes and Regulations" Important safety information, available manual online, or as a printed copy " 安全上のご注意 " for Japan "FUJITSU Server PRIMERGY Information how to install, set up and TX1320 M4 Operating Manual" operate your server, available online "FUJITSU Server PRIMERGY...
Page 30 "Returning used devices" Recycling and contact information, manual available online at http://ts.fujitsu.com/recycling, or as a "Service Desk" leaflet printed copy " サポート＆サービス " for Japan Not applicable in Japan and other countries that have different regulations for recycling...
Page 31 Before you start Document Description Additional documentation RAID documentation, available online at http://manuals.ts.fujitsu.com under x86 Servers - Expansion Cards - Storage Adapters "NVMe User Guide", available online at http://manuals.ts.fujitsu.com under x86 Servers - Expansion Cards - PCIe SSD Devices - SSD PCie3 Main 2.5" H-P EP For Japan: http://www.fujitsu.com/jp/products/computi...
Page 32 Before you start Upgrade and Maintenance Manual TX1320 M4...
Page 33: Important Information
Important information Depending on your server or the installed options some information is not valid for your server. CAUTION! Before installing and starting up a server, please observe the safety instructions listed in the following section. This will help you to avoid making serious errors that could impair your health, damage the server and endanger the data base.
Page 34 Important information If the server is brought in from a cold environment, condensation may form ● both inside and on the outside of the server. Wait until the server has acclimatized to room temperature and is absolutely dry before starting it up. Material damage may be caused to the server if this requirement is not observed.
Page 35 Important information All data and signal cables must have sufficient shielding. The use of cable type S/FTP Cat5 or higher is recommended. Use of unshielded or badly shielded cables may lead to increased emission of interference and/or reduced fault-tolerance of the device. Ethernet cabling has to comply with EN 50173 and EN 50174-1/2 standards ●...
Page 36 Important information Only valid for non hot-plug components ● Before installing/removing internal components to/from the server, turn off the server, all peripheral devices, and any other connected devices. Also unplug all power cords from the power outlet. Failure to do so can cause electric shock or damage.
Page 37 Important information Replace the lithium battery on the system board in accordance with the ● instructions in the corresponding Upgrade and Maintenance Manual, chapter "System board and components" > "CMOS battery". All batteries containing pollutants are marked with a symbol (a crossed-out ●...
Page 38 Important information As a precaution, remove disks from the ODD when the drive is not to ● be used for a long time. Keep the ODD tray closed to prevent foreign matter, such as dust, from entering the ODD. Hold CDs/DVDs/BDs by their edges to avoid contact with the disk ●...
Page 39 Important information Laser information The ODD complies with IEC 60825-1 laser class 1. CAUTION! The ODD contains a light-emitting diode (LED), which under certain circumstances produces a laser beam stronger than laser class 1. Looking directly at this beam is dangerous. Never remove parts of the ODD casing! Modules with Electrostatic-Sensitive Devices (ESD modules) ESD modules are identified by the following sticker:...
Page 40 Important information Do not touch any connectors or conduction paths on an ESD module. ● Place all the components on a pad which is free of electrostatic charge. ● For a detailed description of how to handle ESD modules, see the relevant European or international standards (EN 61340-5-1, ANSI/ESD S20.20).
Page 41: Energy Star
Important information If the server/rack is intended for permanent connection to the mains ● only an authorized specialist (electrician) is allowed to work. Please follow the regulation of each country. If the server is integrated into an installation that draws power from an ●...
Page 42: Ce Conformity
Important information CE conformity The system complies with the requirements of European Regulations. Find the CE declaration on certificate portal: https://sp.ts.fujitsu.com/sites/certificates/default.aspx To open the CE declaration applicable for your system, proceed as follows: Ê Select Industry Standard Servers. Ê Select your model, e.g. Rack server.
Page 43: Fcc Class A Compliance Statement
Consult the dealer or an experienced radio/TV technician for help. ● Fujitsu is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.
Page 44: Environmental Protection
Important information Environmental protection Environmentally-friendly product design and development This product has been designed in accordance with the Fujitsu standard for "environmentally friendly product design and development". This means that key factors such as durability, selection and labeling of materials, emissions, packaging, ease of dismantling and recycling have been taken into account.
Page 45 More information can be found at: http://ts.fujitsu.com/recycling Details regarding the return and recycling of devices and consumables within Europe can also be found in the "Returning used devices" manual, via your local Fujitsu branch, or at: http://ts.fujitsu.com/recycling Upgrade and Maintenance Manual TX1320 M4...
Page 46 Important information Upgrade and Maintenance Manual TX1320 M4...
Page 47: Basic Hardware Procedures
Basic hardware procedures Using diagnostics information Use the Fujitsu ServerView Suite management software to plan the upgrade or replacement of hardware components: Ê In the ServerView Operations Manager Single System View select Maintenance from the Information/Operation menu. It is recommended to prepare local maintenance tasks using remote diagnostics procedures, see the "ServerView Suite Local Service Concept (LSC)"...
Page 48: Locating The Defective Component
Basic hardware procedures – Global Error (for non CSS components) events that need to be resolved by maintenance personnel – Customer Self Service (for CSS components) error events that may be resolved by operating personnel The Global Error indicator and the CSS indicator can be found on the front side and the rear side of the server.
Page 49: Shutting Down The Server
Basic hardware procedures Using the CSS button on the system board If the system has been powered off, the onboard indicators guides you to the faulty component. CAUTION It is mandatory to disconnect all power cords from the system in order to use the Indicate CSS functionality.
Page 50: Disconnecting The Power Cord
Basic hardware procedures Disconnecting the power cord Standard power supply Figure 2: Removing the power cord from the PSU cable tie Ê Pull out the locking lever on the PSU cable tie(s) (1) and loosen the loop (2). Ê Disconnect the power cord from the PSU and remove it from the cable tie. Upgrade and Maintenance Manual TX1320 M4...
Page 51: Getting Access To The Component
Basic hardware procedures Redundant power supply Figure 3: Unlocking the cable clamp of a PSU Ê Press the cable clamp down until it disengages (1). Ê Open the cable clamp (2). Ê Disconnect the power cord from the PSU and remove it from the cable clamp.
Page 52: Removing The Server Cover
Basic hardware procedures 4.4.1 Removing the server cover Ê Remove all external cables from the I/O panel and expansion cards. For more information, see section "Connectors and indicators" on page 319. Figure 4: Removing the ID card Ê Remove the ID card from the server. It may be necessary to pull out on the ID card rather firmly.
Page 53 Basic hardware procedures Figure 6: Removing the server cover Ê Open the locking lever up (1). Ê Slide the server cover towards the front as far as it will go (2). Ê Remove the server cover in a vertical motion (3). Upgrade and Maintenance Manual TX1320 M4...
Page 54: Removing The Accessible Drive Bay Cover
Basic hardware procedures 4.4.2 Removing the accessible drive bay cover Figure 7: Removing the accessible drive bay cover Ê Open the accessible drive bay cover carefully in the direction of the arrow (2) until the cover is released and remove it. Upgrade and Maintenance Manual TX1320 M4...
Page 55 Basic hardware procedures Figure 8: Placing the accessible drive bay cover in front of the HDD bay cover Ê Place the accessible drive bay cover on the HDD bay cover (1). Ê Push the accessible drive bay cover in the direction of the arrow. When operating with tape drives: If the system is programmed to eject the media automatically, the accessible drives must not be obstructed.
Page 56: Removing The Hdd Bay Cover
Basic hardware procedures 4.4.3 Removing the HDD bay cover Figure 9: Removing the HDD bay cover Ê Turn the key counterclockwise (1) to unlock the accessible drive bay cover and remove the key. Ê Open the HDD bay cover in the direction of the arrow and remove it (2). Upgrade and Maintenance Manual TX1320 M4...
Page 57: Reassembling
Basic hardware procedures Reassembling CAUTION! Before attaching the covers, ensure that no unnecessary parts or ● tools are left inside the server. In order to comply with applicable EMC regulations (regulations on ● electromagnetic compatibility) and satisfy cooling requirements, the server must not run while the server cover is removed.
Page 58: Installing The Hdd Bay Cover
Basic hardware procedures 4.5.2 Installing the HDD bay cover Figure 11: Installing the HDD bay cover Ê Insert the HDD bay cover with the lower side into the server cover (1). Ê Close the HDD bay cover (2). Upgrade and Maintenance Manual TX1320 M4...
Page 59: Installing The Accessible Drive Bay Cover
Basic hardware procedures 4.5.3 Installing the accessible drive bay cover Figure 12: Installing accessible drive bay cover Ê Insert the accessible drive bay cover to the upper side of the server cover (1). Ê Close the accessible drive bay cover (2). Ê...
Page 60: Connecting The Power Cord
Basic hardware procedures Figure 13: Installing the ID card Ê Insert and slide the ID card into its slot until it locks in place. Connecting the power cord CAUTION! The server supports a mains voltage in the range of 100 V - 240 V. You may only operate the server if its rated voltage range corresponds to the local mains voltage.
Page 61 Basic hardware procedures Figure 14: Securing power cord Ê Thread the cable tie through the eye (1). Ê Pull the cable tie tight to secure the power cord (2). The insulated connector cannot now be disconnected from the server accidentally. You can loosen the cable tie by opening the small locking lever (2).
Page 62 Basic hardware procedures Redundant power supply Ê Connect the power cords to the PSUs. Ê If applicable, connect the mains plug to a grounded mains outlet in the in- house power supply network. To provide true phase redundancy, the second PSU should be connected to a different AC power source from the other PSU.
Page 63: Switching On The Server
Basic hardware procedures Switching on the server CAUTION! Before switching on the server, ensure that the server cover is closed. ● In order to comply with applicable EMC regulations (regulations on electromagnetic compatibility) and satisfy cooling requirements, the server must not run while the server cover is removed. For more information, see chapter "Important information"...
Page 64: Handling The 2.5-Inch Hdd Cage
Basic hardware procedures Handling the 2.5-inch HDD cage 4.8.1 Removing the 2.5-inch HDD cage Figure 16: Removing the HDD cage (A) Ê Remove the four screws (see circles). Ê Lift the cover from the HDD cage. Figure 17: Removing the HDD cage (B) Ê...
Page 65: Installing The 2.5-Inch Hdd Cage
Basic hardware procedures 4.8.2 Installing the 2.5-inch HDD cage Figure 18: Recesses for the HDD cage (A) Ê Note the designated recesses for the HDD cage (see circles). Figure 19: Installing the HDD cage (A) Ê Put the HDD cage with its rubber feet into the designated recesses (see arrow).
Page 66 Basic hardware procedures Figure 20: Installing the HDD cage (B) Ê Put the cover onto the HDD cage (see arrow). Ê Fasten the HDD cage with four screws and tighten them in a cross diagonal pattern (see circles). Upgrade and Maintenance Manual TX1320 M4...
Page 67: Basic Software Procedures
Basic software procedures Depending on your server and the installed features some information is not valid for your server. Starting the maintenance task 5.1.1 Suspending BitLocker functionality BitLocker Drive Encryption provides protection for operating system and data drives by encrypting the contents and requiring users to authenticate their credentials to access the information.
Page 68: Disabling The Boot Watchdog
For more information on how to suspend BitLocker drive encryption, see the Microsoft TechNet library at http://technet.microsoft.com/library/cc731549.aspx. For more information, see the Fujitsu web pages. 5.1.2 Disabling the boot watchdog The boot watchdog determines whether the operating system boots within a preset time frame.
Page 69: Removing Backup And Optical Disk Media
For Japan: Please contact Fujitsu support, if "forcible" tape ejection is necessary. Fujitsu does not assume responsibility for any damage to the tape drive, the data cartridge/tape or for the loss of any data resulting from manual tape extraction procedures.
Page 70: Verifying And Configuring The Backup Software Solution
For more information on suitable backup software solutions and related documentation, see the Fujitsu web pages. 5.1.5 Switching on the ID indicator For easy identification of the server, switch on the ID indicator, especially when working in a datacenter environment or a server room.
Page 71: Completing The Maintenance Task
After updating or recovering the BIOS and iRMC, enable the boot watchdog again, see section "Enabling the boot watchdog" on page Fujitsu does not assume responsibility for any damage done to the server or for the loss of any data resulting from BIOS updates. 5.2.1.1...
Page 72: Updating The Irmc Firmware
Basic software procedures 5.2.1.2 Updating the iRMC firmware Ê Enter the ServerView iRMC web interface. Ê Select the Tools menu. Ê Select Update to open the Update page. Ê Select iRMC Update. Ê In the iRMC Update group click Select to search the new firmware. Ê...
Page 73: Updating Expansion Card Firmware
"Local System Update for PRIMERGY Servers" user guide Using the flash tool The latest firmware files are available as ASPs (Autonomous Support Packages) for Windows or as DOS tools from the Fujitsu support web pages at: http://ts.fujitsu.com/support/ For Japan: http://www.fujitsu.com/jp/products/computing/servers/primergy/downloads/...
Page 74: Enabling Option Rom Scan
Ê Select Drivers & Downloads. Ê From the Select Product drop down lists, choose your PRIMERGY server Ê Select Server Ê Select Fujitsu Server Primergy Ê Select Product Group Ê Select Product Family or enter its serial or ident number into the search field.
Page 75: Reconfiguring The Backup Software Solution
More information on suitable backup software solutions and related documentation is available from the Fujitsu web pages. Re-enabling backup drives If a backup drive has been disabled or deleted from the backup software drive list as described in section "Verifying and configuring the backup software...
Page 76: Resetting The Boot Retry Counter
Basic software procedures 5.2.6 Resetting the boot retry counter The boot retry counter is decremented from its preset value every time the POST watchdog initiates a system reboot. When the value has reached ’0’, the system will shut down and power off. 5.2.6.1 Viewing the boot retry counter The current boot retry counter status is available in the BIOS:...
Page 77 Basic software procedures Resetting the boot retry counter using the ServerView Operations Manager Ê In the ServerView Operations Manager Administration view, select Server Configuration. Ê If more than one server is managed in SVOM, select the target server and click Next. Ê...
Page 78: Resetting The Error Status After Replacing Memory Modules Or Cpus
Using ServerView Maintenance Tools (Windows only) Ê Launch the ServerView Maintenance Tools: Start > Apps > Fujitsu > Maintenance Tools Ê Choose the Memory status tab. Ê Select the memory module which shows the pre-failure status. Ê Click on Reset Status.
Page 79: Cpus
Using ServerView Maintenance Tools (Windows only) Ê Launch the ServerView Maintenance Tools: Start > Apps > Fujitsu > Maintenance Tools Ê Choose the CPU status tab. Ê Select the CPU which shows the pre-failure status.
Page 80 Basic software procedures Using the command line (Linux only) Proceed as follows to reset the error counter of a specific CPU: Ê Log in as root. Ê Enter the command below, followed by [ENTER]: – For rack and floorstand servers (RX and TX server series): /usr/sbin/eecdcp -c oc=0609 oi=<CPU#>...
Page 81: Enabling The Boot Watchdog
Basic software procedures 5.2.8 Enabling the boot watchdog If the boot watchdog has been disabled for firmware upgrade purposes (see section "Disabling the boot watchdog" on page 68), it has to be re-enabled to complete the maintenance task. Timer settings can be configured in the BIOS or using the ServerView iRMC web interface.
Page 82: Enabling Replaced Components In The Bios
Basic software procedures 5.2.9 Enabling replaced components in the BIOS When a CPU, an expansion card, or a memory module fails, the defective component will be set to Disabled or Failed in the BIOS. The server will then reboot with only the intact hardware components remaining in the system configuration.
Page 83: Verifying The System Time Settings
Basic software procedures Ê Select Memory Status and verify that none of the memory modules are marked as Failed. Ê Select Memory Configuration to verify Memory Mode of Operation. Ê Save your changes (if applicable) and exit the BIOS. For more information on how to access the BIOS and modify settings, see the corresponding BIOS Setup Utility reference manual.
Page 84: Viewing And Clearing The System Event Log (Sel)
Basic software procedures 5.2.12 Viewing and clearing the System Event Log (SEL) 5.2.12.1 Viewing the SEL You can view the System Event Log (SEL) using the ServerView Operations Manager or the ServerView iRMC web interface: Viewing the SEL in ServerView Operations Manager Ê...
Page 85: Clearing The Sel
Basic software procedures All events concerning the system are displayed in a table in the Event Log Content group. Ê You can sort the table based on a column using the arrows in the header field. Ê You can also filter the table using the filter lists in the header of some columns.
Page 86: Updating The Nic Configuration File In A Linux And Vmware Environment
Basic software procedures 5.2.13 Updating the NIC configuration file in a Linux and VMware environment In order to prevent errors caused by changing network device names (eth<x>), it is recommended to store the MAC address (hardware address) of a network interface card in the related NIC configuration file of the Linux/VMware OS.
Page 87: Resuming Bitlocker Functionality
For more information on how to resume BitLocker drive encryption, see the Microsoft TechNet library at http://technet.microsoft.com/library/cc731549.aspx. For more information, see the Fujitsu web pages. 5.2.15 Performing a RAID array rebuild After replacing an HDD that has been combined into a RAID array, RAID rebuild will be performed completely unattended as a background process.
Page 88: Looking For Mac/Wwn/Guid And Sas Addresses
Basic software procedures Figure 21: Progress bar (RAID array rebuild) CAUTION! The system is now operational, however, data redundancy will not be available until the RAID array rebuild is complete. Depending on the HDD capacity the overall process can take up to several hours, in some cases even days.
Page 89: Looking For The Wwn Address Of A Fibre Channel Controller
Only network controllers supporting the Command Line Protocol (CLP) will be displayed. For add-in cards the vendors provide documentation and tools, offered on the Fujitsu support web pages: http://ts.fujitsu.com/support/ Select the server, select Downloads - More Details - Driver. Some vendors bundle the documentation together with the driver package.
Page 90: Looking For The Guid Address Of An Infiniband Or Omni-Path Controller
There are several possible locations where these addresses can be found. Ê Inform the customer about the new SAS address. The customer need the new SAS address, especially when the server is connected to a Fujitsu Storage ETERNUS system. Using ServerView RAID Manager Ê...
Page 91: Using The Chassis Id Prom Tool
Basic software procedures 5.2.17 Using the Chassis ID Prom Tool The front panel (front panel module, front panel board or front panel on QRL) contains the Chassis ID EPROM that stores the following system information: – server name and model –...
Page 92: Configuring Lan Teaming
– from rack model to floorstand model – from floorstand model to rack model Update your system information using the Chassis ID Prom tool. The tool and more information are available to maintenance personnel from the Fujitsu web pages: https://partners.ts.fujitsu.com/com/service/ps/Servers/PRIMERGY/ Ê...
Page 93: After Replacing/Upgrading Lan Controllers
Basic software procedures Ê The Network Interfaces (Summary) overview shows all configured LAN teams and their components. Choose a LAN team to display further details: – LAN Team Properties: Properties of the selected LAN team – LAN Team Statistics: Available statistics about the selected LAN team For more information, see the "ServerView Operations Manager - Server Management"...
Page 94: Performing A Fan Test
Basic software procedures Using the ID button on the front panel Ê Press the ID button on the front panel to switch off the ID indicators. Using the ID icon in the RMC web interface Ê Log in to the iRMC S5 web interface. The icon that represents the ID indicator LED resides on the right of the menu bar.
Page 95 Ê After the fan test is complete, restore the time setting to its initial value and click Save Page. In case of maintenance done by Fujitsu engineers in Japan: Executing the fan test via Chassis ID Prom Tool Please follow the instructions provided separately.
Page 96 Basic software procedures Upgrade and Maintenance Manual TX1320 M4...
Page 97: Power Supply Unit (Psu)
Power supply unit (PSU) Safety notes CAUTION! Do not disassemble the PSU. Doing so may cause electric shock. ● Areas around the PSU may remain extremely hot after shutdown. ● After shutting down the server, wait for hot components to cool down before removing the PSU.
Page 98: Basic Information
(hot-plug). The second PSU can be installed during operation. – with one hot-plug PSU and a Fujitsu battery unit (FJBU) Besides the PSU, an FJBU can be installed optionally as a modular UPS. When power fail happened, the server can operate via FJBU for a while. The FJBU can be replaced during operation (hot-plug).
Page 99: Standard Power Supply
Power supply unit (PSU) Standard power supply 6.2.1 Replacing the standard PSU Field Replaceable Unit Hardware: 10 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 6.2.1.1 Preliminary steps You are advised to perform this routine with the server in a horizontal position.
Page 100 Power supply unit (PSU) Figure 23: Disconnecting the power cables Ê Disconnect the two power cables from the system board connectors "PC98" and "PWR MAIN" (see arrows). Upgrade and Maintenance Manual TX1320 M4...
Page 101 Power supply unit (PSU) Figure 24: Removing the standard PSU Ê Remove the four screws (see circles). Ê While pressing on the latch behind the PSU (see close-up 1) push the PSU a few centimeters toward the inside (2). Ê Take the PSU out upward (3). Upgrade and Maintenance Manual TX1320 M4...
Page 102: Installing The New Standard Psu
Power supply unit (PSU) 6.2.1.3 Installing the new standard PSU Figure 25: Hooks in the bottom of the chassis Ê Take note of the two hooks (see circles). Upgrade and Maintenance Manual TX1320 M4...
Page 103 Power supply unit (PSU) Figure 26: Installing the standard PSU Ê Insert the PSU into the chassis leaving a gap of about 3 cm to the rear chassis wall (1). Ê Ensure that the hooks on the chassis (see circles in figure 25) engages with the notch on the lower surface of the PSU.
Page 104: Concluding Steps
Power supply unit (PSU) Figure 27: Connecting the power cables Ê Connect the power cables to the system board: PSU power cable to connector "PWR MAIN". Power signal cable to connector "PC98". Figure 28: Power cable routing Ê Run the power signal cable between the two retainers (see arrows). 6.2.1.4 Concluding steps "Reassembling"...
Page 105: Redundant Power Supply
Power supply unit (PSU) "Resuming BitLocker functionality" on page 87 Ê "Performing a fan test" on page 94 Ê Redundant power supply PSU 2 PSU 1 Figure 29: PSU bays 6.3.1 Installing a hot-plug PSU Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 6.3.1.1...
Page 106: Removing The Dummy Cover
Power supply unit (PSU) 6.3.1.2 Removing the dummy cover Figure 30: Removing the dummy cover Ê Press in on both release latches (1) and remove the dummy cover (2). CAUTION! Keep the dummy cover for future use. If a PSU is removed and not immediately replaced by a new one, a dummy cover must be installed in the bay again to comply with applicable EMC regulations and satisfy cooling requirements.
Page 107 Power supply unit (PSU) Figure 32: Installing the PSU Ê Push the PSU into its bay (1) as far as it will go until the release latch snaps in place. Ê Fold down the handle on the PSU (2). Ensure that the PSU engages correctly in the bay and is locked in position.
Page 108: Concluding Steps
Power supply unit (PSU) 6.3.1.4 Concluding steps "Connecting the power cord" on page 60 Ê "Performing a fan test" on page 94 Ê 6.3.2 Removing a hot-plug PSU Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 6.3.2.1 Preliminary steps Ê...
Page 109: Removing A Hot-Plug Psu
Power supply unit (PSU) 6.3.2.2 Removing a hot-plug PSU Figure 34: Removing the PSU Ê Push the handle of the PSU halfway upward in the direction of the arrow (1). Ê Press in on the green locking latch (2). Ê While keeping the green locking latch pressed, pull the PSU out of its bay (3).
Page 110: Installing A Dummy Cover
Power supply unit (PSU) 6.3.2.3 Installing a dummy cover Figure 35: Installing the dummy cover Ê Insert the dummy cover into the empty bay with the impressed arrow symbol facing to the left (see circle). Ê Push the dummy cover into its bay until it locks in place. CAUTION! Always install dummy covers into unused bays to comply with applicable EMC regulations and satisfy cooling requirements.
Page 111: Replacing A Hot-Plug Psu
Power supply unit (PSU) 6.3.3 Replacing a hot-plug PSU Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less CAUTION! When replacing a hot-plug PSU in a non-redundant PSU ● configuration, the server must be switched off first. Replace the PSU after specifying the one that breaks down at work ●...
Page 112: Concluding Steps
Power supply unit (PSU) 6.3.3.4 Concluding steps Ê Connect the power cord to the new hot-plug PSU and secure it with a cable tie, see section "Connecting the power cord" on page Ê Only when replacing a hot-plug PSU in a non-redundant configuration: "Switching on the server"...
Page 113 Power supply unit (PSU) Figure 36: Disconnecting cables from the power distribution board Ê Disconnect all cables from the power distribution board (1, 2). Figure 37: Removing the power distribution board Ê Remove one screw through the empty bay (see circle). Ê...
Page 114: Installing The New Power Distribution Board
Power supply unit (PSU) 6.3.4.3 Installing the new power distribution board Figure 38: Recesses in the power distribution board Ê Take note of the four recesses (see ovals). Upgrade and Maintenance Manual TX1320 M4...
Page 115 Power supply unit (PSU) Figure 39: Installing the power distribution board (A) Ê Hook the power distribution board in the hooks at both sides of the PSU cage (see arrows). Ê Fasten the power distribution board through the empty drive bay with one screw (see circle).
Page 116: Concluding Steps
Power supply unit (PSU) Figure 40: Connecting the power distribution board Ê Connect the cables to the power distribution board: PSU signal cable PSU power cable For the cable plans, see chapter "Appendix B" on page 341. Ê Install the PSUs, see section "Installing a hot-plug PSU"...
Page 117: Fujitsu Battery Unit (Fjbu)
Power supply unit (PSU) Fujitsu battery unit (FJBU) 6.4.1 Installing an FJBU Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 6.4.1.1 Preliminary steps No steps needed. 6.4.1.2 Removing the dummy cover Ê Remove the dummy cover, see section "Removing the dummy cover" on page 106.
Page 118: Installing The Fjbu
Power supply unit (PSU) 6.4.1.3 Installing the FJBU Figure 41: Installing the FJBU Ê Push the FJBU into its bay (see arrow) as far as it will go until the locking latch snaps in place. CAUTION! Ensure that the FJBU properly engages in its bay and is locked in position in order to prevent it from sliding out of the chassis during transportation.
Page 119: Removing An Fjbu
Power supply unit (PSU) 6.4.2 Removing an FJBU Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 6.4.2.1 Preliminary steps Ê No steps needed. 6.4.2.2 Removing an FJBU Figure 42: Removing the FJBU Ê Press in on the green locking latch (1). Ê...
Page 120: Installing A Dummy Cover
Power supply unit (PSU) 6.4.2.3 Installing a dummy cover Ê Install the dummy cover, see section "Installing a dummy cover" on page 110. 6.4.3 Replacing an FJBU Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 6.4.3.1 Preliminary steps "Locating the defective server" on page 47 Ê...
Page 121: Preliminary Steps
Power supply unit (PSU) – PSU cage with power distribution board (incl. power cables) – one hot-plug PSU – dummy cover (if only one hot-plug PSU is installed, you have to install the dummy cover in the second bay) – several screws Field Replaceable Unit Hardware: 10 minutes (FRU)
Page 122 Power supply unit (PSU) Figure 43: Removing the standard PSU frame (A) Ê Remove the five screws (see circles). Upgrade and Maintenance Manual TX1320 M4...
Page 123 Power supply unit (PSU) Figure 44: Removing the standard PSU frame (B) Ê Remove the standard PSU frame in the direction of the arrow. Upgrade and Maintenance Manual TX1320 M4...
Page 124: Installing The Upgrade Kit
Power supply unit (PSU) 6.5.3 Installing the upgrade kit Figure 45: Installing the PSU cage (A) Ê Take note of the two hooks (see figure 25). Ê Insert the PSU cage into the chassis leaving a gap of about 3 cm to the rear chassis wall (1).
Page 125 Power supply unit (PSU) Figure 46: Installing the redundant PSU frame (A) Ê Install the redundant PSU frame at a slight angle. The hooks (see circles) must engage in the recesses. Figure 47: Installing the redundant PSU frame (B) Ê Fasten the redundant PSU frame with three screws (see circles). Upgrade and Maintenance Manual TX1320 M4...
Page 126 Power supply unit (PSU) Connecting the power distribution board Ê Connect the cables to the power distribution board (see figure 40). Figure 48: Connecting cables Ê Connect the cables to the system board: PSU power cable to connector "PWR MAIN". PSU signal cable to connector "P30".
Page 127: Concluding Steps
Power supply unit (PSU) 6.5.4 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê "Resuming BitLocker functionality" on page 87 Ê Upgrade and Maintenance Manual TX1320 M4...
Page 128 Power supply unit (PSU) Upgrade and Maintenance Manual TX1320 M4...
Page 129: Hard Disk Drives (Hdd) And Solid State Drives (Ssd)
Hard disk drives (HDD) and solid state drives (SSD) Safety notes CAUTION! Before removing several HDD/SSD modules, make sure that all ● HDD/SSD modules can be reinstalled into their original bay. Otherwise, data may be lost. Do not touch the circuitry on boards or soldered parts. Hold circuit ●...
Page 130: Basic Information
Hard disk drives (HDD) and solid state drives (SSD) Basic information The HDD or SSD and the installation frame together make up the HDD module or SSD module. The server is shipped with one of the following HDD or SSD subsystems: –...
Page 131: Handling Hdds Or Ssds Without Installation Frame
Hard disk drives (HDD) and solid state drives (SSD) Handling HDDs or SSDs without installation frame 7.2.1 2.5-inch HDD/SSD and 2.5-inch installation frame Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: Phillips PH1 / (+) No. 1 screw driver Installing a 2.5-inch HDD/SSD in a 2.5-inch installation frame Figure 49: Installing the 2.5-inch HDD/SSD in the 2.5-inch installation frame (A) Ê...
Page 132 Hard disk drives (HDD) and solid state drives (SSD) Figure 50: Installing the 2.5-inch HDD/SSD in the 2.5-inch installation frame (B) Ê Fasten the 2.5-inch HDD/SSD with four screws. Removing a 2.5-inch HDD/SSD from a 2.5-inch installation frame Ê Proceed in reversed order. Upgrade and Maintenance Manual TX1320 M4...
Page 133: Inch Hdd Configurations
Hard disk drives (HDD) and solid state drives (SSD) 3.5-inch HDD configurations 7.3.1 Configuration with up to two 3.5-inch HDDs Figure 51: Configuration with up to two 3.5-inch HDDs The HDD numbering as listed in the ServerView RAID Manager: Position Logical drive number ServerView RAID Manager display name Vendor Product (0) Vendor Product (1)
Page 134: Installing 3.5-Inch Non Hot-Plug Hdds
Hard disk drives (HDD) and solid state drives (SSD) 7.3.2 Installing 3.5-inch non hot-plug HDDs Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 7.3.2.1 Preliminary steps "Shutting down the server" on page 49 Ê "Disconnecting the power cord" on page 50 Ê...
Page 135 Hard disk drives (HDD) and solid state drives (SSD) Figure 53: Inserting the 3.5-inch non hot-plug HDD (B) Ê Tighten the two knurled screws (see circles). Upgrade and Maintenance Manual TX1320 M4...
Page 136 Hard disk drives (HDD) and solid state drives (SSD) Figure 54: Connecting the 3.5-inch non hot-plug HDD(s) Ê Connect the power cable(s) to the HDD(s): The last but one connector to the lower HDD The last connector to the upper HDD Ê...
Page 137: Concluding Steps
Hard disk drives (HDD) and solid state drives (SSD) 7.3.2.3 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê To configure the installed HDD, see your controller manual. 7.3.3 Removing 3.5-inch non hot-plug HDDs Upgrade and Repair Unit...
Page 138: Removing A 3.5-Inch Non Hot-Plug Hdd
Hard disk drives (HDD) and solid state drives (SSD) In order to permanently remove an operational HDD that is part of a RAID array from the server, you first need to delete the array using ServerView RAID Manager. CAUTION! All data on all HDDs in the array will be lost when deleting the RAID array! Be sure to back up your data before deleting a RAID array.
Page 139: Concluding Steps
Hard disk drives (HDD) and solid state drives (SSD) Figure 56: Removing the 3.5-inch non hot-plug HDD Ê Loosen the two knurled screws from the HDD to be removed (see circles). Ê Pull the non hot-plug HDD out of the bay. 7.3.3.3 Concluding steps "Reassembling"...
Page 140: Replacing A 3.5-Inch Non Hot-Plug Hdd
Hard disk drives (HDD) and solid state drives (SSD) 7.3.4 Replacing a 3.5-inch non hot-plug HDD Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: tool-less 7.3.4.1 Preliminary steps "Locating the defective server" on page 47 Ê "Locating the defective component" on page 48 Ê...
Page 141: Inch Hdd/Ssd Configurations
Hard disk drives (HDD) and solid state drives (SSD) 2.5-inch HDD/SSD configurations 7.4.1 Configuration with up to four HDD/SSD modules Figure 57: Configuration with up to four 2.5-inch HDDs/SSDs Position Logical drive number ServerView RAID Manager display name Vendor Product (0) Vendor Product (1) Vendor Product (2) Vendor Product (3)
Page 142: Configuration With Up To Eight Hdd/Ssd Modules
Hard disk drives (HDD) and solid state drives (SSD) 7.4.2 Configuration with up to eight HDD/SSD modules Figure 58: Configuration with up to eight 2.5-inch HDDs/SSDs Position Logical drive number ServerView RAID Manager display name Vendor Product (0) Vendor Product (1) Vendor Product (2) Vendor Product (3) Vendor Product (4)
Page 143: Configuration With Up To Four Pcie Ssd Modules
Hard disk drives (HDD) and solid state drives (SSD) 7.4.3 Configuration with up to four PCIe SSD modules In the configuration with up to 8 HDD/SSD modules, the first four HDD bays can be equipped with PCIe SSD modules via onboard Oculink connection and a PCIe backplane.
Page 144: Installing 2.5-Inch Hdd/Ssd Modules
Hard disk drives (HDD) and solid state drives (SSD) 7.4.4 Installing 2.5-inch HDD/SSD modules Customer Replaceable Unit Hardware: 5 minutes (CRU) Tools: tool-less 7.4.4.1 Preliminary steps "Getting access to the component" on page 51 Ê Ê Locate the correct drive bay, see section "2.5-inch HDD/SSD configurations"...
Page 145: Installing A 2.5-Inch Hdd/Ssd Module
Hard disk drives (HDD) and solid state drives (SSD) 7.4.4.3 Installing a 2.5-inch HDD/SSD module Figure 61: Opening the locking lever Ê Pinch the green locking clips (1) and open the locking lever (2). Figure 62: Inserting the 2.5-inch HDD/SSD module Ê...
Page 146: Concluding Steps
Hard disk drives (HDD) and solid state drives (SSD) Configuring the RAID array, see the documentation of the RAID controller, used in your configuration, see section "Documentation overview" on page 7.4.4.4 Concluding steps "Reassembling" on page 57 Ê 7.4.5 Removing 2.5-inch HDD/SSD modules Customer Replaceable Unit Hardware: 5 minutes (CRU)
Page 147: Removing A 2.5-Inch Hdd/Ssd Module
Hard disk drives (HDD) and solid state drives (SSD) In order to permanently remove an operational HDD/SSD module that is part of a RAID array from the server, you first need to delete the array using ServerView RAID Manager. CAUTION! All data on all HDDs/SSDs in the array will be lost when deleting the RAID array! Be sure to back up your data before deleting a RAID array.
Page 148: Installing A 2.5-Inch Hdd/Ssd Dummy Module
Hard disk drives (HDD) and solid state drives (SSD) 7.4.5.3 Installing a 2.5-inch HDD/SSD dummy module CAUTION! If the removed HDD/SSD module is not replaced immediately, always replace a dummy module into the unused HDD/SSD bay to comply with applicable EMC regulations and satisfy cooling requirements. Figure 63: Installing the 2.5-inch HDD/SSD dummy module Ê...
Page 149: Replacing A 2.5-Inch Hdd/Ssd Module
Hard disk drives (HDD) and solid state drives (SSD) 7.4.6 Replacing a 2.5-inch HDD/SSD module Customer Replaceable Unit Hardware: 5 minutes (CRU) – Installation frame included: tool-less Tools: – Installation frame excluded: Phillips PH1 / (+) No. 1 screw driver CAUTION! Only remove an HDD/SSD module during operation if the drive is not ●...
Page 150: Preliminary Steps
Hard disk drives (HDD) and solid state drives (SSD) 7.4.6.1 Preliminary steps "Locating the defective server" on page 47 Ê "Getting access to the component" on page 51 Ê "Locating the defective component" on page 48 Ê 7.4.6.2 Removing the defective 2.5-inch HDD/SSD module Ê...
Page 151: Replacing A 2.5-Inch Backplane
Hard disk drives (HDD) and solid state drives (SSD) 7.4.7 Replacing a 2.5-inch backplane Field Replaceable Unit Hardware: 10 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 7.4.7.1 Preliminary steps The HDD backplane is mounted on the HDD cage. It is not necessary to remove the HDD cage before installing or removing the HDD backplane.
Page 152 Hard disk drives (HDD) and solid state drives (SSD) Configurations with up to eight 2.5-inch HDDs/SSDs, there are either two HDD backplanes or one PCIe backplane (backplane 1) and one HDD backplane (backplane 2). Ê If there are two backplanes, locate the defective backplane. Ê...
Page 153 Hard disk drives (HDD) and solid state drives (SSD) Figure 65: Example: Removing the HDD backplane 2 Ê Remove the two screws (see circles). Ê Lift the HDD backplane up (1) and remove it from the HDD cage (2). Upgrade and Maintenance Manual TX1320 M4...
Page 154: Installing A Hdd/Pcie Backplane
Hard disk drives (HDD) and solid state drives (SSD) 7.4.7.3 Installing a HDD/PCIe backplane Figure 66: Example: Installing the HDD backplane 2 Ê Insert the HDD backplane in the three hooks on the bottom of the HDD cage (see arrows). Ê...
Page 155: Connecting Cables
Hard disk drives (HDD) and solid state drives (SSD) 7.4.7.4 Connecting cables Example: Connecting a PCIe backplane (backplane 1) Figure 67: Example: Connecting cables - OOB and power to backplane 1 Ê Connect the cables to the backplane: If applicable, OOB cable Power cable Ê...
Page 156 Hard disk drives (HDD) and solid state drives (SSD) Figure 68: Example: Connecting cables - PCIe cable to backplane 1 Ê Connect the cables to the backplane: Oculink cable (red) to backplane connector "P3-X4" Oculink cable (yellow) to backplane connector "P2-X3" Oculink cable (green) to backplane connector "P1-X2"...
Page 157 Hard disk drives (HDD) and solid state drives (SSD) Example: Connecting an HDD backplane (backplane 2) Figure 69: Example: Connecting cables - OOB and power to backplane 2 Ê Connect the cables to the backplane: If applicable, OOB cable Power cable Ê...
Page 158: Concluding Steps
Hard disk drives (HDD) and solid state drives (SSD) Ê Run the OOB cable as shown. For the cable plan, see chapter "Appendix B" on page 341. 7.4.7.5 Concluding steps Ê Insert all HDD/SSD modules, see section "Installing 2.5-inch HDD/SSD modules"...
Page 159: Preliminary Steps
Hard disk drives (HDD) and solid state drives (SSD) 7.4.8.1 Preliminary steps The HDD backplane is mounted on the HDD cage. It is not necessary to remove the HDD cage before installing or removing the HDD backplane. "Shutting down the server" on page 49 Ê...
Page 160: Installing Additional Hdd/Ssd Modules
Hard disk drives (HDD) and solid state drives (SSD) 7.4.8.4 Installing additional HDD/SSD modules Figure 71: Removing the HDD cover Ê Press in on both release latches (1) and remove the HDD cover (2). Ê Insert additional HDD/SSD modules, see section "Installing 2.5-inch HDD/SSD modules"...
Page 161: Upgrading To 4X Pcie 2.5-Inch Ssd Configuration
Hard disk drives (HDD) and solid state drives (SSD) 7.4.9 Upgrading to 4x PCIe 2.5-inch SSD configuration A PCIe backplane can only be installed as the first backplane. Mixing of an HDD backplane and a PCIe SSD backplane is not allowed. A PCIe SSD backplane needs a PRAID EP5x0i, see section "Example PRAID EP5x0i"...
Page 162: Installing The Pcie Backplane
Hard disk drives (HDD) and solid state drives (SSD) 7.4.9.2 Installing the PCIe backplane Ê Break out the plastic flap of the HDD fan module by hand from the HDD fan module, see figure 74. Ê Install the PCIe backplane, see section "Installing a HDD/PCIe backplane"...
Page 163: Fans
"Important information" on ● page Basic information The PRIMERGY TX1320 M4 server features two different HDD fan modules. Since the system fan is not redundant, it has to be replaced immediately in case of defects or pre-failure events. Upgrade and Maintenance Manual...
Page 164: Hdd Fan Module 2.5-Inch Hdd Variant
Fans HDD fan module 2.5-inch HDD variant HDD fan 2 HDD fan 1 Figure 72: HDD fan position 8.2.1 Replacing the HDD fan module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 8.2.1.1 Preliminary steps "Locating the defective server" on page 47 Ê...
Page 165: Removing The Hdd Fan Module
Fans 8.2.1.2 Removing the HDD fan module Figure 73: Removing the HDD fan module fan module Ê Press on the green tab (1) and remove the HDD fan module from the HDD cage (2). Ê Disconnect the fan cable from system board (3). Upgrade and Maintenance Manual TX1320 M4...
Page 166: Breakout And Recess In The Hdd Fan Module
Fans 8.2.1.3 Breakout and recess in the HDD fan module Figure 74: HDD fan module - breakout and recess Breakout for the Oculink cables If using a PCIe backplane: Ê Break out the plastic flap of the HDD fan module by hand (see oval) so that the color-coded Oculink cables can be run through the breakout.
Page 167: Installing The Hdd Fan Module
Fans 8.2.1.4 Installing the HDD fan module Figure 75: Installing the HDD fan module (2.5-inch) Ê Connect the fan cable to system board connector "FAN2" (1). For the second HDD fan module use the system board connector "FAN4". Ê If applicable, run the SAS cable through the recess in the HDD fan, see figure 74 on page 166.
Page 168: Hdd Fan Module 3.5-Inch Hdd Variant
Fans HDD fan module 3.5-inch HDD variant 8.3.1 Replacing the HDD fan module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 8.3.1.1 Preliminary steps "Locating the defective server" on page 47 Ê "Shutting down the server" on page 49 Ê...
Page 169: Removing The Hdd Fan Module
Fans 8.3.1.2 Removing the HDD fan module Figure 76: Removing the HDD fan module (3.5-inch) Ê Disconnect the fan cable from system board (1). Ê Pull the locking lever away from the HDD cage to disengage the fan module (close-up 2). Ê...
Page 170: Installing The Hdd Fan Module
Fans 8.3.1.3 Installing the HDD fan module Figure 77: Installing the HDD fan module (3.5-inch) Ê Insert the HDD fan module into the chassis. Ê Engage the HDD fan at the rear of the HDD cage and slide it to the right (1) until it locks in place.
Page 171: Expansion Cards And Backup Units
Expansion cards and backup units Safety notes CAUTION! Do not damage or modify internal cables or devices. Doing so may ● cause a device failure, fire, or electric shock. Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.
Page 172: Basic Information
167,65 mm / Dedicated slot for PCIe (notched)(mech. X8) low profile graphics card For system relevant information, see the hardware configurator of your server available online at the following address: http://ts.fujitsu.com/products/standard_servers/index.html For Japan: http://www.fujitsu.com/jp/products/computing/servers/primergy/ Upgrade and Maintenance Manual TX1320 M4...
Page 173: Handling Slot Brackets
Expansion cards and backup units Handling slot brackets 9.2.1 Installing a slot bracket Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver Use the low profile bracket perforated for relevant controllers. Figure 79: Perforated and non-perforated slot brackets Full height bracket non-perforated Full height bracket perforated Low profile bracket perforated...
Page 174: Removing A Slot Bracket
Expansion cards and backup units Example: EP4x0i Figure 80: Placing the slot bracket Ê Place the controller on the slot bracket (see arrow). Ê Secure the slot bracket to the expansion card with two screws (see circles). 9.2.2 Removing a slot bracket Upgrade and Repair Unit Hardware: 5 minutes (URU)
Page 175: Handling Sfp+ Transceiver Modules
Expansion cards and backup units Handling SFP+ transceiver modules A network adapter is equipped with one or two SFP+ (small form-factor pluggable) transceiver modules. SFP+ transceiver modules are hot-pluggable. 9.3.1 Installing SFP+ transceiver modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less Preparing the SFP+ transceiver module...
Page 176 Expansion cards and backup units Figure 82: Unlatching the locking bail Ê Carefully unlatch and fold down the locking bail on the SFP+ transceiver module. Inserting the SFP+ transceiver module Figure 83: Inserting the SFP+ transceiver module Ê Insert and slide the SFP+ transceiver module into the socket connector as far as it will go.
Page 177 Expansion cards and backup units Figure 84: Latching the locking bail Ê Carefully fold up and latch the locking bail. Figure 85: Installing the protective cap Ê If the SFP+ transceiver module is not immediately connected to an LC connector, attach the protective cap to the SFP+ transceiver module. Upgrade and Maintenance Manual TX1320 M4...
Page 178: Removing An Sfp+ Transceiver Module
Expansion cards and backup units Installing the secondary SFP+ transceiver module Figure 86: Installing the secondary SFP+ transceiver module Ê If applicable, install the secondary SFP+ transceiver module accordingly. 9.3.2 Removing an SFP+ transceiver module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less A network adapter is equipped with one or two SFP+ (small form-factor...
Page 179 Expansion cards and backup units Figure 87: Removing the protective cap Ê If present, remove the protective cap from the SFP+ transceiver module. CAUTION! Keep the protective cap for future use. Figure 88: Unlatching the locking bail Ê Carefully unlatch and fold down the locking bail on the SFP+ transceiver module to eject the transceiver from the socket connector.
Page 180: Expansion Cards
Expansion cards and backup units Figure 89: Removing the SFP+ transceiver module Ê Pull the SFP+ transceiver module out of its socket connector. Ê Attach the protective cap to the SFP+ transceiver module. Place the removed SFP+ transceiver module in an antistatic bag or other protective environment.
Page 181: Removing A Pci Slot Cover
Expansion cards and backup units Ê If applicable, install the slot bracket, see section "Installing a slot bracket" on page 173. 9.4.1.2 Removing a PCI slot cover Figure 90: Removing the PCI slot cover Ê Fold up the PCI slot cover clamp (1). Ê...
Page 182 Expansion cards and backup units For further instructions regarding controller settings, see the accompanying documentation. Ê If applicable, attach the required slot bracket to the expansion card, see section "Installing a slot bracket" on page 173. Ê If applicable, connect internal cables to the expansion card. For the cable plan, see chapter "Appendix B"...
Page 183 Expansion cards and backup units Example PRAID EP5x0i Figure 92: Connecting cables - PRAID EP5x0ixi Ê Connect the cables to the PRAID EP5x0i: If applicable, FBU cable HDD LED cable Ê Install the PRAID EP5x0i in slot 3, see section "Installing expansion cards"...
Page 184 Expansion cards and backup units Figure 93: Connecting HDD LED cable and SAS cables Ê Connect the cables of the PRAID EP5x0i: HDD LED cable to connector "HDD LED" on the system board If applicable, the SAS cables from the backplanes (depending on the configuration) Upgrade and Maintenance Manual TX1320 M4...
Page 185 Expansion cards and backup units Figure 94: Connecting Oculink cables Ê If applicable, connect the Oculink cables of the PRAID EP5x0i: Oculink cable (red) to connector "C0" Oculink cable (yellow) to connector "C1" Oculink cable (green) to connector "C2" Oculink cable (black) to connector "C3" For the cable plan, see chapter "Appendix B"...
Page 186: Concluding Steps
Expansion cards and backup units 9.4.1.4 Concluding steps "Reassembling" on page 57 Ê Ê If applicable, connect external cables to the expansion card. "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê "Updating expansion card firmware" on page 73 Ê...
Page 187: Removing Expansion Cards
Expansion cards and backup units 9.4.2 Removing expansion cards Upgrade and Repair Unit Hardware: 5 minutes (URU) Phillips PH2 / (+) No. 2 screw driver (only for removing the slot Tools: bracket) 9.4.2.1 Preliminary steps "Suspending BitLocker functionality" on page 67 Ê...
Page 188: Removing An Expansion Card
Expansion cards and backup units 9.4.2.3 Removing an expansion card Ê If applicable, remove SFP+ transceiver modules from the expansion card, see section "Removing an SFP+ transceiver module" on page 178. Ê If an EP5x0i is installed, disconnect the HDD LED cable from the system board.
Page 189: Concluding Steps
Expansion cards and backup units Figure 97: Installing a PCI slot cover Ê Insert a slot cover into the unused PCI slot opening (1). Ê Fold down slot bracket clamp until it locks in place (2). 9.4.2.5 Concluding steps "Reassembling" on page 57 Ê...
Page 190: Replacing Expansion Cards
Expansion cards and backup units 9.4.3 Replacing expansion cards Upgrade and Repair Unit Hardware: 5 minutes (URU) Software: 5 minutes Phillips PH2 / (+) No. 2 screw driver (only for replacing the slot Tools: bracket) Note on network settings recovery When replacing network controllers or the system board, network configuration settings in the operating system will be lost and replaced by default values.
Page 191: Installing An Expansion Card
Expansion cards and backup units 9.4.3.3 Installing an expansion card Ê If applicable, install the slot bracket, see section "Installing a slot bracket" on page 173. Ê Install the expansion card, see section "Installing the expansion card" on page 181. 9.4.3.4 Concluding steps "Reassembling"...
Page 192: Replacing Tfm
Expansion cards and backup units 9.4.4 Replacing TFM Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH1 / (+) No.1 screw driver 9.4.4.1 Preliminary steps "Locating the defective server" on page 47 Ê "Shutting down the server" on page 49 Ê...
Page 193 Expansion cards and backup units Figure 99: Removing the TFM Ê Remove the two screws (1). Ê Remove the TFM (2). Note for replacing the TFM: The two spacer bolts can remain on the RAID controller. Upgrade and Maintenance Manual TX1320 M4...
Page 194: Installing The New Tfm
Expansion cards and backup units 9.4.4.3 Installing the new TFM Example RAID controller Figure 100: Installing the TFM (A) Ê If no TFM has been installed before: fit the two spacer bolts on the RAID controller. Upgrade and Maintenance Manual TX1320 M4...
Page 195 Expansion cards and backup units Figure 101: Installing the TFM (B) Ê Fasten the TFM on the RAID controller with the two screws from the TFM kit. Upgrade and Maintenance Manual TX1320 M4...
Page 196: Concluding Steps
Expansion cards and backup units Figure 102: Connecting the FBU adapter cable Ê Connect the FBU adapter cable to the TFM. Ê Install the SAS RAID controller, see section "Installing expansion cards" on page 180. 9.4.4.4 Concluding steps "Reassembling" on page 57 Ê...
Page 197: Flash Backup Unit (Fbu)
Expansion cards and backup units Flash backup Unit (FBU) The FBU backs up the memory contents of the RAID controller in the event of a power failure. You can install one FBU. 9.5.1 Installing an FBU Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH1 / (+) No.1 screw driver (for installing the TFM)
Page 198: Preparing The Fbu
Expansion cards and backup units 9.5.1.2 Preparing the FBU Figure 103: Installing the FBU in the holder (A) Ê At a slight angle, fit the FBU under both retaining brackets of the holder. Ê Push in the FBU until it locks in place. Figure 104: Installing the FBU in the holder (B) Ê...
Page 199: Removing The Fbu Tray
Expansion cards and backup units Figure 105: Connecting the FBU adapter cable to the FBU Ê Connect the FBU cable to the FBU adapter cable. 9.5.1.3 Removing the FBU tray Figure 106: Removing the FBU holder Ê Press on the green tab (1 close-up) and push the FBU tray from inside of the chassis in order to take it out of the bay (2).
Page 200: Installing The Fbu Into The Fbu Tray
Expansion cards and backup units 9.5.1.4 Installing the FBU into the FBU tray Figure 107: Installing the FBU (A) Ê Insert the FBU into the FBU tray so that the three hooks rest in the tray and slide it in the direction of the arrow until it locks in place. Upgrade and Maintenance Manual TX1320 M4...
Page 201: Connecting The Fbu
Expansion cards and backup units Figure 108: Installing the FBU (B) Ê Insert the FBU tray into the corresponding bay and slide it into the bay as far as it will go (see arrow). 9.5.1.5 Connecting the FBU Ê If applicable, install the TFM, see section "Installing the new TFM"...
Page 202: Removing An Fbu
Expansion cards and backup units 9.5.2 Removing an FBU Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less CAUTION! Dispose of used battery properly. Keep away from children. ● Do not throw flash backup units into the trash can. Batteries must be ●...
Page 203: Disconnecting The Fbu Cable From The Fbu
Expansion cards and backup units Figure 109: Removing the FBU Ê Slide the FBU in the direction of the arrow and remove the FBU from the FBU tray. 9.5.2.3 Disconnecting the FBU cable from the FBU Figure 110: Disconnecting the FBU cable from the FBU Ê...
Page 204: Installing The Fbu Tray
Expansion cards and backup units 9.5.2.4 Installing the FBU tray Figure 111: Installing the FBU tray Ê Install the FBU tray into the corresponding bay and slide it into the bay as far as it will go (see arrow). 9.5.2.5 Concluding steps Ê...
Page 205: Replacing An Fbu
Expansion cards and backup units 9.5.3 Replacing an FBU Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: tool-less CAUTION! Dispose of used battery properly. Keep away from children. ● Do not throw flash backup units into the trash can. Batteries must be ●...
Page 206: Concluding Steps
Expansion cards and backup units Ê Connect the FBU, see section "Connecting the FBU" on page 201. 9.5.3.4 Concluding steps "Connecting the front USB connector" on page 267 Ê "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê...
Page 207: Main Memory
Main memory Safety notes CAUTION! Before removing several memory modules, make sure that all ● memory modules can be reinstalled into their original slots. Otherwise, data may be lost. Do not install unsupported third party memory modules. For more ● information on supported memory modules, see section "Basic information"...
Page 208: Basic Information
Main memory 10.1 Basic information PC98 FAN4 DIMM1B USB 1 DIMM2B DIMM1A Micro DIMM2A DIMM1B DIMM2B DIMM1A DIMM2A PWR MAIN USB 2 PWR1 Management iRMC LAN / USB 2.0 Shared LAN 1 / Intel i210 USB 2.0 PWD CLR LAN 1 RCVR LAN 2 / Figure 112: Slots of the main memory...
Page 209: Modes Of Operation
Main memory Channel Slot ID Table 3: Mounting order - dual channel mode and single channel mode: Single CPU 10.1.1.2 Modes of operation – The maximum performance can be achieved in a symmetric dual-channel configuration. Therefore both channels have to be populated with the same amount of memory.
Page 210: Installing A Memory Module
Main memory 10.2 Installing a memory module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 10.2.1 Preliminary steps "Suspending BitLocker functionality" on page 67 Ê "Shutting down the server" on page 49 Ê "Disconnecting the power cord" on page 50 Ê...
Page 211: Installing A Memory Module
Main memory 10.2.3 Installing a memory module Figure 113: Opening the securing clips Ê Press the securing clips on both sides of the memory slot concerned outward. Figure 114: Installing a memory module Ê Align the notch on the bottom of the module with the crossbar in the slot. Ê...
Page 212: Concluding Steps
Main memory Figure 115: Correct position of securing clips To improve the contact of the memory module perform the following steps: Ê Eject the memory module again by pressing out the securing clips at each end of the memory slot. Ê...
Page 213: Removing A Memory Module
Main memory 10.3 Removing a memory module Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 10.3.1 Preliminary steps "Suspending BitLocker functionality" on page 67 Ê "Shutting down the server" on page 49 Ê "Disconnecting the power cord" on page 50 Ê...
Page 214: Concluding Steps
Main memory 10.3.3 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê "Resuming BitLocker functionality" on page 87 Ê 10.4 Replacing memory modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Software: 5 minutes...
Page 215: Installing The New Memory Module
Main memory 10.4.3 Installing the new memory module Ê Install the memory module, see section "Installing a memory module" on page 211. 10.4.4 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê...
Page 216 Main memory Upgrade and Maintenance Manual TX1320 M4...
Page 217: Processor (Cpu)
CPU E-21xx, E-22xx, Pentium, or Core i3 up to 95W, up to 8 cores – one CPU socket LGA 1151 For system relevant information, see the hardware configurator of your server available online at the following address: http://ts.fujitsu.com/products/standard_servers/index.html For Japan: http://www.fujitsu.com/jp/products/computing/servers/primergy/ Upgrade and Maintenance Manual TX1320 M4...
Page 218: Upgrading Or Replacing The Cpu
Processor (CPU) 11.2 Upgrading or replacing the CPU Field Replaceable Unit Hardware: 15 minutes (FRU) Software: 5 minutes Tools: Phillips PH2 / (+) No. 2 screw driver CAUTION! CPUs are modules which are extremely sensitive to electro-static discharges and therefore must always be handled with care. After a CPU has been removed from its protective sleeve or from its socket, place it with its smooth side down on a non-conducting, antistatic surface.
Page 219: Removing The Heat Sink Variant 1
Processor (CPU) 11.2.2 Removing the heat sink variant 1 Figure 118: Removing the heat sink variant 1 Ê Disconnect the CPU fan cable from the system board (see arrow). Ê Loosen the four captive screws on the heat sink in a crossover pattern (1-4). Ê...
Page 220: Removing The Heat Sink Variant 2
Processor (CPU) This may be necessary due to the adhesive quality of the thermal paste located between the heat sink and CPU. CAUTION! Pay special attention not to damage any system board components surrounding the CPU socket. Ê Lift the heat sink out of the chassis. Ê...
Page 221: Removing The Cpu
Processor (CPU) Ê Disconnect the CPU fan cable from the system board (see arrow). Ê Loosen the four captive screws on the heat sink in a crossover pattern (1-4). Ê Carefully twist the heat sink back and forth to detach it from the CPU. This may be necessary due to the adhesive quality of the thermal paste located between the heat sink and CPU.
Page 222 Processor (CPU) Figure 121: Opening the load plate Ê Rotate the socket lever to lift the load plate away from the socket. Ê Ensure that the load plate is in the fully open position. Upgrade and Maintenance Manual TX1320 M4...
Page 223 Processor (CPU) Figure 122: Removing the CPU Ê Carefully remove the CPU from its socket in a vertical motion. CAUTION! Be careful not to touch or bend the spring contacts on the CPU socket. Upgrade and Maintenance Manual TX1320 M4...
Page 224: Installing The Cpu
Processor (CPU) 11.2.5 Installing the CPU Ê Confirm that the CPU model number printed on the top of the CPU fits with the requirements. Ê If applicable, remove the protective cap from the bottom side of the CPU. Figure 123: Installing the CPU Ê...
Page 225 Processor (CPU) Figure 124: Closing the load plate (A) Ê Lower the load plate over the CPU while leaving the socket lever in the open position. Upgrade and Maintenance Manual TX1320 M4...
Page 226 Processor (CPU) Figure 125: Closing the load plate (B) Ê Lower the socket lever while making sure that the front edge of the load plate slides under the shoulder screw cap (see close-up) as the lever is lowered. Figure 126: Closing the socket release lever Ê...
Page 227: Applying Thermal Paste
Processor (CPU) 11.2.6 Applying thermal paste For Japan, the service engineer must follow the instruction provided separately. If the CPU upgrade or replacement kit contains a new heat sink, a thin layer of thermal compound has already been pre-applied to its lower surface.
Page 228 Processor (CPU) Figure 128: Applying thermal paste Ê Apply a small point-shaped amount of thermal paste (1.0 gram, see description above) to the center of the CPU surface as shown. CAUTION! Do not mix different types of thermal paste. Upgrade and Maintenance Manual TX1320 M4...
Page 229: Installing The Heat Sink Variant 1
Processor (CPU) 11.2.7 Installing the heat sink variant 1 Figure 129: Installing the heat sink variant 1 Ê Carefully seat the heat sink on the four threaded holes as shown. CAUTION! – Ensure that the screws on the heat sink are properly seated on the threaded holes.
Page 230: Installing The Heat Sink Variant 2
Processor (CPU) Ê Connect the CPU fan cable to the connector "FAN1" on the system board (see arrow). 11.2.8 Installing the heat sink variant 2 Figure 130: Installing the heat sink variant 2 Ê Ensure that the heat sink cooling fins match the direction of the airflow! Ê...
Page 231: Concluding Steps
Processor (CPU) Ê Fasten the four captive screws on the heat sink in a crossover pattern (torque 6.0 Nm, not applicable for Japan) (1-4). Ê Connect the CPU fan cable to the connector "FAN1" on the system board (see arrow). 11.2.9 Concluding steps "Reassembling"...
Page 232: Replacing The Heat Sink
Processor (CPU) 11.3 Replacing the heat sink Field Replaceable Unit Hardware: 15 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 11.3.1 Preliminary steps "Locating the defective server" on page 47 Ê "Shutting down the server" on page 49 Ê...
Page 233: Concluding Steps
Processor (CPU) 11.3.4 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê "Performing a fan test" on page 94 Ê 11.4 Handling the protective cover 11.4.1 Installing the protective cover Figure 131: Attaching the protective socket cover Ê...
Page 234 Processor (CPU) Figure 132: Closing the load plate (A) Ê Lower the load plate over the CPU cover while leaving the socket lever in its open position. Upgrade and Maintenance Manual TX1320 M4...
Page 235 Processor (CPU) Figure 133: Closing the load plate (B) Ê Lower the socket lever while making sure that the front edge of the load plate slides under the shoulder screw cap (see close-up) as the lever is lowered. Figure 134: Latching the socket lever Ê...
Page 236: Removing The Protective Cover
Processor (CPU) 11.4.2 Removing the protective cover Figure 135: Opening socket release lever Ê Unlatch the socket release lever by pushing it down and away from the socket (1). Ê Fold back the socket release lever (2). Upgrade and Maintenance Manual TX1320 M4...
Page 237 Processor (CPU) Figure 136: Opening the load plate Ê Press down on the socket lever to lift the load plate away from the socket. Ê Fully open the load plate. Upgrade and Maintenance Manual TX1320 M4...
Page 238 Processor (CPU) Figure 137: Removing the protective cover Ê Remove the protective cover from the CPU socket. Proceed as follows: Ê Place your thumb against the front edge of the protective socket cover and rest your index finger on the rear grip. Ê...
Page 239: Accessible Drives
Accessible drives Safety notes CAUTION! Before installing an accessible drive, acquaint yourself with the ● drive's user documentation. When inserting an accessible drive into the server, ensure not to ● pinch or strain any connected cables. When installing an accessible drive, hold it by its sides. Applying force ●...
Page 240: Basic Information
Accessible drives 12.1 Basic information Mounting order for accessible drives PRIMERGY TX1320 M4 server offers a 5.25-inch slimline SATA ODD bay and 3.5-inch USB backup drive bay: Figure 138: Accessible drives mounting order Accessible drive Max. # 5.25-inch bay2 3.5-inch bay...
Page 241: Optical Disk Drive (Odd)
Accessible drives 12.2 Optical disk drive (ODD) 12.2.1 Installing the ODD Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: Phillips PH1 / (+) No. 1 screw driver 12.2.1.1 Preliminary steps "Suspending BitLocker functionality" on page 67 Ê "Shutting down the server" on page 49 Ê...
Page 242: Removing The Odd Filler Cover
Accessible drives 12.2.1.2 Removing the ODD filler cover Figure 139: Removing the ODD filler cover Ê Grip the green ODD latch of the ODD filler cover (see arrow), pull out the cover and remove it from its installation bay. CAUTION! Save the ODD filler cover for future use.
Page 243: Installing The Odd Latch
Accessible drives 12.2.1.3 Installing the ODD latch Figure 141: Installing the ODD latch on the ODD Ê Fasten the ODD latch with two screws to the rear side of the ODD (see circles). Upgrade and Maintenance Manual TX1320 M4...
Page 244 Accessible drives Figure 142: Installing the ODD (A) Ê Insert the ODD with the ODD latch first into its installation bay (see arrow) and push it until the small green latch is visible on the rear of the cage. Figure 143: Installing the ODD (B) Ê...
Page 245 Accessible drives Figure 144: Connecting cables to the ODD Ê Connect the connector "P5" of the power cable to the connector on the ODD (1). Ê Connect the SATA cable to the ODD (2) and to the system board connector "SATA ODD"...
Page 246: Concluding Steps
Accessible drives 12.2.1.4 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê "Resuming BitLocker functionality" on page 87 Ê For the cable plan, see chapter "Appendix B" on page 341.
Page 247 Accessible drives Figure 145: Unlocking the ODD Ê Press the ODD latch in direction of the arrow until it disengages Figure 146: Removing the ODD Ê Pull the ODD out of the bay (see arrow). Upgrade and Maintenance Manual TX1320 M4...
Page 248 Accessible drives Figure 147: Removing the ODD latch Ê Remove the two screws (see circles). Ê Remove the ODD latch. Ê If no new ODD will be installed: Ê Fasten the ODD latch with two screws to the ODD filler cover (see figure 140).
Page 249: Concluding Steps
Accessible drives Figure 148: Install the ODD filler cover Ê Install the ODD filler cover into the empty bay (see arrow). 12.2.2.3 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê...
Page 250: Replacing The Odd
Accessible drives 12.2.3 Replacing the ODD Field Replaceable Unit Hardware: 15 minutes (FRU) Tools: Phillips PH1 / (+) No. 1 screw driver 12.2.3.1 Preliminary steps "Locating the defective server" on page 47 Ê "Removing backup and optical disk media" on page 69 Ê...
Page 251: Backup Drive (Rdx)
Accessible drives 12.3 Backup drive (RDX) 12.3.1 Installing the RDX drive Upgrade and Repair Unit Hardware: 10minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver 12.3.1.1 Preliminary steps "Suspending BitLocker functionality" on page 67 Ê "Shutting down the server" on page 49 Ê...
Page 252 Accessible drives Figure 149: Removing the backup drive filler Ê Hold the backup drive filler cover by its two handle recesses (1) and pull it out of the installation bay (2). CAUTION! Keep the drive filler cover for future use. Always replace dummy modules into unused drive bays to comply with applicable EMC regulations and satisfy cooling requirements.
Page 253: Installing The Rdx Drive
Accessible drives 12.3.1.3 Installing the RDX drive Figure 150: Installing the RDX drive (A) Ê Insert the RDX drive into its installation bay. Ê Carefully push back until the backup drive cover plate is flush with the front panel. Upgrade and Maintenance Manual TX1320 M4...
Page 254 Accessible drives Figure 151: Installing the RDX drive (B) Ê Fasten the RDX drive to the drive cage with two screws. Use the screw hole marked "1st". Upgrade and Maintenance Manual TX1320 M4...
Page 255: Concluding Steps
Accessible drives Figure 152: Connecting cables to the RDX drive Ê Connect the connector "P4" of the power cable to the connector on the ODD (1). – Connect the USB cable to the RDX drive (2) and to the system board connector "USB 2"...
Page 256: Removing The Rdx Drive
Accessible drives 12.3.2 Removing the RDX drive Field Replaceable Unit Hardware: 10minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 12.3.2.1 Preliminary steps "Removing backup and optical disk media" on page 69 Ê "Suspending BitLocker functionality" on page 67 Ê...
Page 257 Accessible drives Figure 153: Removing the RDX drive (A) Ê Remove the two screws (see circles). Figure 154: Removing the RDX drive (B) Ê Pull the RDX drive out of its bay. Upgrade and Maintenance Manual TX1320 M4...
Page 258: Inserting The Drive Filler
Accessible drives 12.3.2.3 Inserting the drive filler Figure 155: Inserting the drive filler cover Ê Insert the drive filler cover (see arrow). Ê Install the HDD fan modules, see section "Installing the HDD fan module" on page 167. 12.3.2.4 Concluding steps "Reassembling"...
Page 259: Replacing The Rdx Drive
Accessible drives 12.3.3 Replacing the RDX drive Field Replaceable Unit Hardware: 10minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver 12.3.3.1 Preliminary steps "Locating the defective server" on page 47 Ê "Removing backup and optical disk media" on page 69 Ê...
Page 260 Accessible drives Upgrade and Maintenance Manual TX1320 M4...
Page 261: Front Panel
Front panel Safety notes CAUTION! When inserting the front panel module into the server, ensure not to ● pinch or strain any connected cables. Circuit boards and soldered parts of internal options are exposed and ● can be damaged by static electricity. Always discharge static build-up (e.g.
Page 262: Front Panel Module
Front panel 13.1 Front panel module 13.1.1 Replacing the front panel module Field Replaceable Unit Hardware: 10 minutes (FRU) Software: 5 minutes Tools: flat screw driver (for the retention hooks) Note on system information backup/restore The front panel (front panel module, front panel board or front panel on QRL) contains the Chassis ID EPROM that contains system information like server name and model, housing type, serial number and manufacturing data.
Page 263: Preliminary Steps
Front panel 13.1.1.1 Preliminary steps "Locating the defective server" on page 47 Ê "Suspending BitLocker functionality" on page 67 Ê "Shutting down the server" on page 49 Ê "Disconnecting the power cord" on page 50 Ê "Getting access to the component" on page 51 Ê...
Page 264: Installing The Front Panel Module
Front panel 13.1.1.3 Installing the front panel module Figure 157: Inserting the front panel module Ê Insert the front panel module as shown and carefully push in until it locks in place (see arrow). Ê Connect the front panel cable to the front panel module (1). Upgrade and Maintenance Manual TX1320 M4...
Page 265: Concluding Steps
Front panel 13.1.1.4 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê "Verifying system information backup/restore" on page 72 Ê "Using the Chassis ID Prom Tool" on page 91 Ê...
Page 266: Installing The Front Usb Connector
Front panel 13.2.1.3 Installing the front USB connector Figure 158: Installing the front USB connector Ê Place the front USB connector in the FBU tray and slide it in the direction of the arrow until it locks in place. Ê Fasten the USB front connector with two screws. Figure 159: Installing the front USB connector Ê...
Page 267: Connecting The Front Usb Connector
Front panel 13.2.1.4 Connecting the front USB connector Figure 160: Connecting front USB connector cable Ê Connect the front USB connector cable end to the connector "USB 3.1 FRONT" on the system board (1). Ê If applicable, connect the FBU adapter cable to the TFM, see section "Installing the new TFM"...
Page 268: Removing A Front Usb Connector
Front panel 13.2.2 Removing a Front USB connector Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver 13.2.2.1 Preliminary steps "Shutting down the server" on page 49 Ê "Disconnecting the power cord" on page 50 Ê...
Page 269: Removing The Front Usb Connector From Fbu Tray
Front panel 13.2.2.3 Removing the front USB connector from FBU tray Ê Remove the FBU tray, see section "Removing the FBU tray" on page 265. Figure 162: Removing the front USB connector Ê Remove the two screws. Ê Remove the front USB connector from the FBU tray (see arrow). 13.2.2.4 Installing the FBU tray Ê...
Page 270: Replacing A Front Usb Connector
Front panel 13.2.3 Replacing a front USB connector Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: Phillips PH2 / (+) No. 2 screw driver 13.2.3.1 Preliminary steps "Locating the defective server" on page 47 Ê "Shutting down the server" on page 49 Ê...
Page 271: System Board And Components
System board and components Safety notes CAUTION! Devices and components inside the server remain hot after ● shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options. Circuit boards and soldered parts of internal options are exposed and ●...
Page 272: Basic Information
System board and components 14.1 Basic information This section provides instructions for the system board and the following components: CMOS battery ● The real-time clock is powered by a lithium coin cell (CMOS battery) when mains get lost. This cell lasts up to five years, depending on ambient temperature and use.
Page 273: Cmos Battery
System board and components 14.2 CMOS battery 14.2.1 Replacing the CMOS battery Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less; recommended: tooth pick Safety notes CAUTION! The CMOS battery must be replaced with an identical battery or with ●...
Page 274: Replacing The Defective Cmos Battery
System board and components 14.2.1.2 Replacing the defective CMOS battery Figure 163: Replacing the CMOS battery Ê Press the locking spring into direction of the arrow (1), so that the CMOS battery jumps out of its socket. Ê Remove the CMOS battery (2). CAUTION! Sharp tools such as screw drivers might damage system board components in case of slipping.
Page 275: Trusted Platform Module (Tpm)
System board and components 14.3 Trusted Platform Module (TPM) Figure 164: TPM kit Special screw for TPM TPM spacer TPM bit insert for TPM special screw Upgrade and Maintenance Manual TX1320 M4...
Page 276: Installing The Tpm
System board and components 14.3.1 Installing the TPM Field Replaceable Unit Hardware: 5 minutes (FRU) Software: 5 minutes Tools: – Bit screw driver – TPM bit insert For Japan: – TPM module fixing tool (S26361-F3552-L909) 14.3.1.1 Preliminary steps "Suspending BitLocker functionality" on page 67 Ê...
Page 277: Concluding Steps
System board and components Figure 167: TPM bit insert Ê Attach the TPM bit insert or TPM module fixing tool (for Japan) to a bit screw driver. Figure 168: Installing the TPM Ê Connect the TPM to the system board (1). Ê...
Page 278: Removing The Tpm
System board and components Ê Enable TPM in the system board BIOS. Proceed as follows: Ê Switch on or restart your server. Ê As soon as the startup screen appears, enter the BIOS setup menu. Ê Select the Advanced menu. Ê...
Page 279: Preliminary Steps
For more information on how to disable BitLocker drive encryption, see the Microsoft Knowledge Base. For more information, see the Fujitsu web pages. Ê Disable TPM in the system board BIOS. Proceed as follows: Ê Switch on or restart your server.
Page 280: Removing The Tpm
System board and components "Shutting down the server" on page 49 Ê "Disconnecting the power cord" on page 50 Ê "Getting access to the component" on page 51 Ê 14.3.2.2 Removing the TPM Ê Remove the system board, see section "Removing the defective system board"...
Page 281: Concluding Steps
System board and components Otherwise the thin metal bar may break, rendering it impossible to loosen the screw. Ê Remove the TPM screw (3). Ê Remove the TPM on the upper side of the system board. Figure 170: Removing the TPM spacer Ê...
Page 282: Replacing The Tpm
System board and components 14.3.3 Replacing the TPM Field Replaceable Unit Hardware: 40 minutes (FRU) Tools: Removing the system board: – Phillips PH2 / (+) No. 2 screw driver Replacing the TPM: – Bit screw driver – TPM bit insert –...
Page 283: Removing The Defective Tpm
System board and components 14.3.3.2 Removing the defective TPM Ê Remove the TPM, see section "Removing the TPM" on page 278. Ê Leave the TPM spacer on the system board when removing the defective TPM. 14.3.3.3 Installing the new TPM The TPM spacer is already present on the system board.
Page 284: Irmc Microsd Card
System board and components 14.4 iRMC microSD card The iRMC microSD card is necessary for using the embedded Lifecycle Management (eLCM) functionality of the iRMC. It requires a valid eLCM license key, which is always purchased together with the iRMC microSD card and activated through the iRMC web interface.
Page 285: Concluding Steps
System board and components Figure 172: Installing the iRMC microSD card Ê With the label facing up, insert the iRMC microSD card into the microSD card slot (1) as far as it will go (2). The onboard position of the microSD card slot can be found in section "Connectors and indicators on the system board"...
Page 286: Removing The Irmc Microsd Card
System board and components 14.4.2 Removing the iRMC microSD card Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 14.4.2.1 Preliminary steps "Shutting down the server" on page 49 Ê "Disconnecting the power cord" on page 50 Ê "Getting access to the component" on page 51 Ê...
Page 287: Concluding Steps
System board and components 14.4.2.3 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê 14.4.3 Replacing the iRMC microSD card Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: a pair of side-cutting pliers 14.4.3.1 Preliminary steps...
Page 288: Concluding Steps
System board and components 14.4.3.3 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê 14.5 M.2 SSD The system board offers two M.2 slots (Key M) with support for 42 mm, 60 mm, 80 mm and 110 mm long M.2 SSDs.
Page 289: Installing The M.2 Ssd
System board and components 14.5.1.2 Installing the M.2 SSD Figure 174: Example M.2 SSD Figure 175: Slots for M.2 SSDs M.2 slot 1 M.2 slot 2 Upgrade and Maintenance Manual TX1320 M4...
Page 290 System board and components CAUTION! The M.2 slot 1 must be equipped first. An M.2 SSD in M.2 slot 2 is not recognized, if M.2 slot 1 is free. Each M.2 SSD needs one hexagon stand-off for fastening. To support different length of M.2 SSD, several nuts are on the system board indicating the positions for fastening the M.2 SSD.
Page 291: Concluding Steps
System board and components 14.5.1.3 Concluding steps Ê If applicable, connect the SATA cable of the ODD from the system board. Ê If applicable, connect the Oculink cables to the PCIe backplane. Ê If applicable, install the HDD fan module 2.5-inch HDD variant, see section "Replacing the HDD fan module"...
Page 292: Removing The M.2 Ssd
In order to setup the ESXi, see the corresponding version of the "VMware vSphere Software Description" from the following URL and reinstall ESXi to the M.2 SSD. http://jp.fujitsu.com/platform/server/primergy/software/vmware/manual/ 14.5.2 Removing the M.2 SSD Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: –...
Page 293: Removing The M.2 Ssd
System board and components 14.5.2.2 Removing the M.2 SSD Figure 178: Removing the M.2 SSD (A) Ê Remove the screw (see circle). Figure 179: Removing the M.2 SSD (B) Ê Pull the M.2 SSD out of its slot. Ê If no new M.2 SSD will be installed: Ê...
Page 294: Concluding Steps
System board and components 14.5.2.3 Concluding steps Ê If applicable, connect the SATA cable of the ODD from the system board. Ê If applicable, connect the Oculink cables to the PCIe backplane. Ê If applicable, "Installing expansion cards" on page 180.
Page 295: Replacing The M.2 Ssd
System board and components 14.5.3.2 Replacing the M.2 SSD Ê Remove the defective M.2 SSD, see section "Removing the M.2 SSD" on page 292. Ê Install the new M.2 SSD, see section "Installing an M.2 SSD" on page 288. 14.5.3.3 Concluding steps Ê...
Page 296: Dual Microsd 64Gb Enterprise
System board and components 14.6 Dual microSD 64GB Enterprise 14.6.1 Installing the Dual microSD 64GB Enterprise Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 14.6.1.1 Preliminary steps "Shutting down the server" on page 49 Ê "Disconnecting the power cord" on page 50 Ê...
Page 297 System board and components Figure 181: Connecting the cable to the Dual microSD 64GB Enterprise Ê Connect the cable to the Dual microSD 64GB Enterprise. Figure 182: Installing the Dual microSD 64GB Enterprise Ê Insert the Dual microSD 64GB Enterprise into the system board connector "USB 1"...
Page 298: Concluding Steps
System board and components 14.6.1.3 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Connecting the power cord" on page 60 Ê 14.6.1.4 Software configuration In order to install the ESXi to the Dual microSD 64GB Enterprise, the VMware ESXi installer CD is required.To obtain the ESXi installer CD by purchasing the OEM Media Kit, or downloading the ESXi Custom Image ISO file from VMware's website and burn the image to the CD.
Page 299: Removing The Dual Microsd 64Gb Enterprise
In order to setup the ESXi, see the corresponding version of the "VMware vSphere Software Description" from the following URL and reinstall ESXi to the Dual microSD 64GB Enterprise. http://jp.fujitsu.com/platform/server/primergy/software/vmware/manual/ 14.6.2 Removing the Dual microSD 64GB Enterprise Upgrade and Repair Unit...
Page 300: Concluding Steps
System board and components Figure 183: Removing the Dual microSD 64GB Enterprise Ê Pull the Dual microSD 64GB Enterprise out of its connector. 14.6.2.3 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê...
Page 301: Replacing The Dual Microsd 64Gb Enterprise
System board and components 14.6.3 Replacing the Dual microSD 64GB Enterprise Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less 14.6.3.1 Preliminary steps "Locating the defective server" on page 47 Ê "Shutting down the server" on page 49 Ê "Disconnecting the power cord"...
Page 302: Concluding Steps
System board and components Figure 185: Installing the microSD card Ê With the label facing up, insert the microSD card into the microSD slot on the controller (1) until it locks in place (2). Ê Install the new Dual microSD 64GB Enterprise, see section "Installing the Dual microSD 64GB Enterprise"...
Page 303: Replacing The Microsd Card
System board and components 14.6.4 Replacing the microSD card Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: a pair of side-cutting pliers 14.6.4.1 Preliminary steps "Locating the defective server" on page 47 Ê "Shutting down the server" on page 49 Ê...
Page 304: Concluding Steps
System board and components Ê Install the Dual microSD 64GB Enterprise, see section "Installing the Dual microSD 64GB Enterprise" on page 296. 14.6.4.3 Concluding steps "Reassembling" on page 57 Ê "Connecting the power cord" on page 60 Ê "Switching on the server" on page 63 Ê...
Page 305 System board and components Note on TPM The system board can be equipped with an optional TPM (Trusted Platform Module). This module enables third party programs to store key information (e. g. drive encryption using Windows Bitlocker Drive Encryption). If the customer is using TPM functionality, the TPM has to be removed from the defective system board and connected to the new system board.
Page 306: Preliminary Steps
System board and components Note on network settings recovery When replacing network controllers or the system board, network configuration settings in the operating system will be lost and replaced by default values. This applies to all static IP address and LAN teaming configurations.
Page 307: Removing The Defective System Board
System board and components 14.7.1.2 Removing the defective system board Ê Disconnect all cables from the system board. Ê If applicable, remove all HDDs, see section "Removing 2.5-inch HDD/SSD modules" on page 146. Ê If applicable, remove the HDD cage, see section "Removing the 2.5-inch HDD cage"...
Page 308 System board and components Figure 187: Removing the system board Ê Use both hands to lift the system board carefully out of the chassis in a slight angle. Thereby you pull the connectors out of the I/O panel (see arrows). CAUTION! Always take the system board with both hands! Never lift the system board one-sided or at a heat sink, because the...
Page 309: Installing The New System Board
System board and components 14.7.1.3 Installing the new system board Ê If applicable, install the iRMC microSD card, see section "Installing the iRMC microSD card" on page 284. Ê If applicable, install the TPM, see section "Installing the TPM" on page 276.
Page 310: Concluding Steps
System board and components 14.7.1.4 Concluding steps Ê Connect all cables to the system board. For the cable plan, see chapter "Appendix B" on page 341. Ê Install all remaining system board components as shown in the related sections: – M.2 SSD (if applicable): see section "Installing an M.2 SSD"...
Page 311 System board and components Ê As soon as the startup screen appears, press the [F2] function key to enter the BIOS. If a password is assigned, enter the password and press [Enter]. Ê Select the Save & Exit menu. Ê Select Save Changes and Exit or Save Changes and Reset. Ê...
Page 312 System board and components Upgrade and Maintenance Manual TX1320 M4...
Page 313: Mechanical Overview
Appendix A 15.1 Mechanical overview 15.1.1 Server front Figure 188: Front side 2.5-inch variant Pos. Component 4x 2.5-inch HDDs/SSDs SAS/SATA/PCIe ID card slot 4x 2.5-inch HDDs/SSDs SAS/SATA Backup drive USB connectors Front panel module Upgrade and Maintenance Manual TX1320 M4...
Page 314 Appendix A Figure 189: Front side 3.5-inch variant Pos. Component 3.5-inch HDDs SATA ID card slot Backup drive USB connectors Front panel module Upgrade and Maintenance Manual TX1320 M4...
Page 315: Server Rear
Appendix A 15.1.2 Server rear Figure 190: Rear side with standard power supply Pos. Component Management LAN connector Shared LAN connector (LAN1) Standard LAN connector (LAN2) 4x Optional expansion card 2x USB 3.1 Gen 1 connector 4x USB connector 2.0 VGA video connector Serial connector CSS / Global Error / ID indicators...
Page 316 Appendix A Figure 191: Rear side with redundant power supply Pos. Component Management LAN connector Shared LAN connector (LAN1) Standard LAN connector (LAN2) 4x Optional expansion card 2x USB 3.1 Gen 1 connector 4x USB connector 2.0 VGA video connector Serial connector CSS / Global Error / ID indicators Up to 2 PSUs / dummy cover...
Page 317: Server Interior
Appendix A 15.1.3 Server interior 86,026 Figure 192: Interior (2.5-inch HDD variant with redundant power supply) Pos. Component PSU bays Accessible drive bay Front panel module bay HDD/SSD/PCIe SSD bays HDD fans System board D3673 PCIe slots CPU / heat sink Memory modules Upgrade and Maintenance Manual TX1320 M4...
Page 318 Appendix A Figure 193: Interior (3.5-inch HDD variant with standard power supply) Pos. Component Standard PSU Accessible drive bay Front panel module bay HDD bays HDD fans System board D3673 PCIe slots CPU / heat sink Memory modules Upgrade and Maintenance Manual TX1320 M4...
Page 319: Connectors And Indicators
Appendix A 15.2 Connectors and indicators 15.2.1 Connectors and indicators on the system board 15.2.1.1 Onboard connectors PC98 FAN4 DIMM1B USB 1 DIMM2B DIMM1A Micro DIMM2A DIMM1B DIMM2B DIMM1A DIMM2A PWR MAIN USB 2 PWR1 Management iRMC LAN / USB 2.0 Shared LAN 1 / Intel i210...
Page 320 Appendix A No. Print Description PWR MAIN PSU connector USB 1 Connector for Dual microSD 64GB Enterprise Connector for Dual microSD 64GB Enterprise cable PC98 Data cable connector for standard PSU FAN4 Power connector for HDD fan 2 (2.5-inch HDD) MICRO SD iRMC microSD card FRONTPANEL...
Page 321: Onboard Indicators And Controls
Appendix A 15.2.1.2 Onboard indicators and controls PC98 FAN4 DIMM1B USB 1 DIMM2B DIMM1A Micro DIMM2A DIMM1B DIMM2B DIMM1A DIMM2A PWR MAIN USB 2 PWR1 Management iRMC LAN / USB 2.0 Shared LAN 1 / Intel i210 PWD CLR USB 2.0 LAN 1 RCVR LAN 2 /...
Page 322 Appendix A The LEDs have the following meaning: Indicator Status Description A - Identification blue on The server has been highlighted using ServerView Operations Manager, iRMC web interface or the ID button on the front panel for easy identification. blue flashing The server has been highlighted for easy identification using the iRMC (AVR) with disabled local VGA output.
Page 323: Server Front
Appendix A Indicator Status Description I - Fans system fan running orange on system fan failure K - Standby orange on All standby voltages ok Power O - M.2 SSD orange on M.2 SSD faulty 15.2.2 Server front 15.2.2.1 Indicators on the front panel Figure 196: Indicators on the front panel Pos.
Page 324 Appendix A Pos. Label Indicator Status Description No critical event detected (CSS component). Prefailure event detected (CSS component). orange [CSS] indicator For HDDs/SSDs, see also "HDD prefailure detection" on page 326. flashing CSS component failure detected. orange No critical event detected (non CSS component).
Page 325 Appendix A Pos. Label Indicator Status Description – The server is switched off and connected to the mains (standby mode). – The server has been switched on but Power Cycle Delay settings delay it from turning on for a green on specified time.
Page 326: Indicator On The Odd
Appendix A HDD prefailure detection Depending on your hardware configuration HDD prefailure detection will be supported. The requirements are: – iRMC S5 Firmware 1.2 or later – supported OOB RAID system 15.2.2.2 Indicator on the ODD ODDs may have an indicator or not. Figure 197: Example: Indicator on the ODD Pos.
Page 327: Indicators On The Hot-Plug Hdd Module
Appendix A 15.2.2.3 Indicators on the hot-plug HDD module Figure 198: Indicators on the hot-plug HDD/SSD module Pos. Label Indicator Status Description The HDD/SSD is inactive. Access indicator green on The HDD/SSD being accessed No HDD/SSD error detected. An HDD/SSD error has been detected.
Page 328: Server Rear
Appendix A 15.2.3 Server rear 15.2.3.1 Connectors on the I/O panel Figure 199: Connectors on the I/O panel Management LAN connector for 4x USB 2.0 connectors iRMC server management function Shared LAN connector (LAN1) Video connector (VGA) Standard LAN connector (LAN2) Serial connector COM1* 2x USB 3.1 Gen 2 connectors The serial connector can be used as the standard interface or for...
Page 329: Indicators On The I/O Panel
Appendix A 15.2.3.2 Indicators on the I/O panel ID, CSS and Global Error indicators Figure 200: ID, CSS and Global Error indicators Pos. Label Indicator Status Description The server has been highlighted using ServerView Operations indicator, blue on Manager, iRMC web frontend or see also the ID button on the front panel for "iRMC-...
Page 330 Appendix A Pos. Label Indicator Status Description No critical event detected (non CSS component). orange Prefailure event detected (non Global CSS component). Error indicator, Non CSS component failure see also detected. "iRMC- Possible causes: related – System is out of the specified orange status range...
Page 331 Appendix A HDD prefailure detection Depending on your hardware configuration HDD prefailure detection will be supported. The requirements are: – iRMC S5 Firmware 1.2 or later – supported OOB RAID system LAN indicators Figure 201: LAN indicators Pos. Indicator Status Description A LAN connection has been green on...
Page 332 Appendix A Indication of LAN connection supporting Energy Efficient Ethernet (EEE mode) To configure the EEE mode, it is necessary that the on board LAN or an add in LAN card supports this mode and the connected switch supports this mode as well.
Page 333: Indicator On Hot-Plug Psu
Appendix A 15.2.3.3 Indicator on hot-plug PSU Figure 202: Indicator on hot-plug PSU Pos. Indicator Status Description flashing The server is switched off, but mains green voltage is present (standby mode). The server is switched on and operating green on properly.
Page 334: Indicator On Fjbu
Appendix A 15.2.3.4 Indicator on FJBU Figure 203: Indicator on FJBU Pos. Indicator Status Description flashing The battery unit is charging. green flashing green The battery unit is discharging. slowly FJBU status green on The battery unit is fully charged. indicator A battery unit failure has been detected.
Page 335: Acoustic Indicators
Appendix A 15.2.4 Acoustic indicators PEI Beep Codes Pre-EFI Initialization (PEI) - memory Initialization (bootblock) # of Description Action Beep Memory not installed Ê Check if the memory module is installed. Ê Check if the memory module is installed correctly. Recovery started Recovery procedure is initialized by jumper settings on the system board and announced...
Page 336 Appendix A # of Description Action Beep Flash update is failed A processing bar and an error message is displayed on the screen. This beep code is only an information. Platform PCI resource Ê Check the connection of your expansion requirements cannot card whether it is installed in a correct be met...
Page 337: Onboard Settings
Appendix A 15.3 Onboard settings PWR1 Management iRMC LAN / USB 2.0 Shared LAN 1 / Intel i210 USB 2.0 PWD CLR LAN 1 RCVR LAN 2 / SATA USB 3.1 Gen 2 Indicate FAN1 Slot 4 Intel Slot 3 i210 Battery Slot 2...
Page 338: Minimum Startup Configuration
Appendix A 15.4 Minimum startup configuration Field Replaceable Units (FRU) If the server does not start up or other problems occur, it may be necessary to take the system down to its most basic configuration in order to isolate the defective component.
Page 339 Appendix A "Switching on the server" on page Ê CAUTION! Since the fan module is not included in the minimum startup configuration, the server must be shut down immediately after the diagnostic process is complete (POST phase has been passed). The minimum startup configuration must be used exclusively for diagnostic purposes by maintenance personnel, never in daily operation!
Page 340 Appendix A Upgrade and Maintenance Manual TX1320 M4...
Page 341: Appendix B
Appendix B The following documents are available in this appendix: – "Cable plan for FUJITSU Server PRIMERGY TX1320 M4 Reference Manual" – "List of Released Adapters incl. Installation sequence and priority" – "List of all used screws for PRIMERGY Servers - Assembled in Germany and Japan"...
Page 342 Appendix B Upgrade and Maintenance Manual TX1320 M4...
Page 343 Reference Manual - English Cable Plan for FUJITSU Server PRIMERGY TX1320 M4 Reference Manual January 2019...
Page 344 Cable Plan Contents Frontpage Contents List of used cables SYS Board Connector D3673 Basic Cabling Basic_PDB_Std_PSU Basic_PDB_Red_PSU Cabling_Pwr_35inch_HDD Cabling_Pwr_25inch_HDD Cabling_Pwr_25inch_NVMe Cabling_ACC_Drv CablingData4/8x25inchSAS_HDD CablingData25inchSATA_HDD CablingData35inchSATA_HDD CablingData35inchSATA_HDD_EP4 CablingData35inchSATA_HDD_EP5 CablingEP5x0i_HDD_Signal CablingEP5x0i_NVME_Signal CablingEP5x0i_NVME_EP4x0i_SASSATA Cabling2xEP5x0i Dual_Micro_SD_64GB_Enterprise System FANs TX1320 M4...
Page 345: List Of Used Cables
Cable Plan List of used cables Ref. Name Number Routing Basic CBL_FRONTPANEL T26139-Y4015-V303 Basic Cabling CBL_USB_360 T26139-Y3999-V507 Basic Cabling CBL SATA ODD T26139-Y4028-V306 Cabling_ACC_Drv CBL_MoBo_DRV_Pw_35 T26139-Y4012-V505 CablingPower35inch_HDD CBL_MoBo_DRV_Pw_25 T26139-Y4012-V504 Cabling_Pwr_25inch_HDD; Cabling_Pwr_25inch_NVMe CablingData35inchSATA_HDD; CBL_SAS30_SATA_350 T26139-Y4040-V43 CablingData35inchSATA_HDD_EP4 CablingData35inchSATA_HDD_EP5 CablingData4/8x25inchSAS_HDD; CablingData25inchSATA_HDD; CBL_OOB_HDD_2BP T26139-Y4015-V608 CablingEP5x0i_NVME_EP4x0i_SASSATA Cabling2xEP5x0i CBL_PDB_MoBo_Pw...
Page 346: Sys Board Connector D3673
Cable Plan SYS Board Connector D3673 Systemboard D3673 FRONTPANEL USB 3.1 FRONT PC98 PWR MAIN PWR 1 SATA 0-3 SATA ODD USB 2 HDD LED INTR FAN 1 FAN 2 FAN 3 FAN 4 TX1320 M4...
Page 347: Basic Cabling
Cable Plan Basic Cabling Systemboard D3673 Front Panel Y4015-V303 Front Panel FRONTPANEL USB 3.1 FRONT PC98 Y3999-V507 Front Drawer PWR MAIN PWR 1 USB 3.1 Gen 1 SATA 0-3 SATA ODD USB 2 HDD LED INTR FAN 1 FAN 2 FAN 3 FAN 4 TX1320 M4...
Page 348: Basic_Pdb_Std_Psu
Cable Plan Basic_PDB_Std_PSU Systemboard D3673 FRONTPANEL Std PSU USB 3.1 FRONT PC98 Data PWR MAIN PWR 1 SATA 0-3 SATA ODD USB 2 HDD LED INTR FAN 1 FAN 2 FAN 3 FAN 4 TX1320 M4...
Page 349: Basic_Pdb_Red_Psu
Cable Plan Basic_PDB_Red_PSU Systemboard D3673 FRONTPANEL USB 3.1 FRONT Power Distribution Board PC98 Y3956-V4 Data PWR MAIN Y3952-V511 PWR 1 SATA 0-3 SATA ODD USB 2 HDD LED INTR FAN 1 FAN 2 FAN 3 FAN 4 TX1320 M4...
Page 350: Cabling_Pwr_35Inch_Hdd
Cable Plan Cabling_Pwr_35inch_HDD Systemboard D3673 AccDriveCage FRONTPANEL USB 3.1 FRONT PC98 SATA PWR MAIN Y4012-V505 PWR 1 SATA 0-3 HDD Cage 3.5" SATA ODD USB 2 HDD2 SATA HDD LED INTR HDD1 FAN 1 SATA FAN 2 FAN 3 FAN 4 TX1320 M4...
Page 351: Cabling_Pwr_25Inch_Hdd
Cable Plan Cabling_Pwr_25inch_HDD Systemboard D3673 AccDriveCage FRONTPANEL USB 3.1 FRONT PC98 SATA PWR MAIN PWR 1 Y4012-V504 SATA 0-3 HDD Cage 2.5" SATA ODD USB 2 BPL2 SATA HDD LED INTR BPL1 FAN 1 SATA FAN 2 FAN 3 FAN 4 TX1320 M4...
Page 352: Cabling_Pwr_25Inch_Nvme
Cable Plan Cabling_Pwr_25inch_NVMe Systemboard D3673 AccDriveCage FRONTPANEL USB 3.1 FRONT PC98 SATA PWR MAIN Y4012-V504 PWR 1 SATA 0-3 HDD Cage 2.5" SATA ODD USB 2 NVMe 4 HDD LED BPL1 NVMe 3 INTR NVMe 2 FAN 1 NVMe1 FAN 2 FAN 3 FAN 4 TX1320 M4...
Page 353: Cabling_Acc_Drv
Cable Plan Cabling_ACC_Drv Systemboard D3673 AccDriveCage FRONTPANEL USB 3.1 FRONT PC98 SATA PWR MAIN Y4028-V306 PWR 1 SATA 0-3 SATA ODD Y4039-A11 USB 2 HDD LED INTR FAN 1 FAN 2 FAN 3 FAN 4 TX1320 M4...
Page 354: Cablingdata4/8X25Inchsas_Hdd
Cable Plan CablingData4/8x25inchSAS_HDD HDD Cage 2.5" System Board D3673 Y4015-V608 BPL2 Y4040-V77 SATA BPL1 SATA Y4040-V77 MLC2 SAS RAID CP/EP4x0i Front Drawer MLC1 Y4031-V102 TX1320 M4...
Page 355: Cablingdata25Inchsata_Hdd
Cable Plan CablingData25inchSATA_HDD Systemboard D3673 FRONTPANEL USB 3.1 FRONT PC98 HDD Cage 2.5" PWR MAIN PWR 1 SATA 0-3 Y4040-V77 Y4015-V608 BPL1 SATA ODD SATA USB 2 HDD LED INTR FAN 1 FAN 2 FAN 3 FAN 4 TX1320 M4...
Page 356: Cablingdata35Inchsata_Hdd
Cable Plan CablingData35inchSATA_HDD Systemboard D3673 FRONTPANEL USB 3.1 FRONT PC98 HDD Cage 3.5" PWR MAIN PWR 1 HDD2 SATA 0-3 Y4040-V43 SATA SATA ODD HDD1 SATA USB 2 HDD LED INTR FAN 1 FAN 2 FAN 3 FAN 4 TX1320 M4...
Page 357: Cablingdata35Inchsata_Hdd_Ep4
Cable Plan CablingData35inchSATA_HDD_EP4 System Board D3673 HDD Cage 3.5" HDD2 SATA MLC2 SAS RAID HDD1 CP/EP4x0i Y4040-V43 MLC1 SATA Front Drawer Y4031-V102 TX1320 M4...
Page 358: Cablingdata35Inchsata_Hdd_Ep5
Cable Plan CablingData35inchSATA_HDD_EP5 System Board D3673 HDD Cage 3.5" HDD2 SATA SAS RAID HDD1 EP5x0i Y4040-V43 SATA Front Drawer Y4031-V107 TX1320 M4...
Page 359: Cablingep5X0I_Hdd_Signal
Cable Plan CablingEP5x0i_HDD_Signal HDD Cage 2.5" System Board D3673 Y4015-V608 BPL2 Y4040-V77 SATA BPL1 Y4040-V77 SATA SAS RAID EP5x0i Front Drawer Y4031-V107 TX1320 M4...
Page 360: Cablingep5X0I_Nvme_Signal
Cable Plan CablingEP5x0i_NVME_Signal System Board HDD Cage 2.5" Y4015-V608 Y4050-V25 P3_X4 BPL1 Y4050-V25 P2_X3 Y4050-V26 P1_X2 EP5x0i Y4050-V26 P0_X1 Y4031-V107 SCAP Front Drawer J10DAC Y2361-V103 HDD LED TX1320 M4...
Page 361: Cablingep5X0I_Nvme_Ep4X0I_Sassata
Cable Plan CablingEP5x0i_NVME_EP4x0i_SASSATA System Board HDD Cage 2.5" Y4015-V608 P3_X4 Y4050-V25 BPL1 P2_X3 Y4050-V25 P1_X2 Y4050-V26 EP5x0i P0_X1 Y4050-V26 Y4031-V107 SCAP J10DAC Front Drawer Y2361-V103 HDD LED HDD Cage 2.5" MLC2 SAS RAID BPL2 CP/EP4x0i Y4040-V77 MLC1 SATA TX1320 M4...
Page 362: Cabling2Xep5X0I
Cable Plan Cabling2xEP5x0i System Board HDD Cage 2.5" Y4015-V608 P3_X4 Y4050-V25 BPL1 P2_X3 Y4050-V25 P1_X2 Y4050-V26 EP5x0i P0_X1 Y4050-V26 SCAP Y4031-V107 J10DAC Front Drawer Y2361-V105 HDD LED EP5x0i HDD Cage 2.5" BPL2 SCAP Y4040-V77 SATA J10DAC TX1320 M4...
Page 363: Dual_Micro_Sd_64Gb_Enterprise
Cable Plan Dual_Micro_SD_64GB_Enterprise Systemboard D3673 FRONTPANEL USB 3.1 FRONT PC98 PWR MAIN PWR 1 SATA 0-3 SATA ODD USB 2 DUAL_MICRO_SD_ 64GB_Enterprise Y4018-V8 HDD LED INTR FAN 1 FAN 2 FAN 3 FAN 4 TX1320 M4...
Page 364: System Fans
Cable Plan System FANs Systemboard D3673 FRONTPANEL USB 3.1 FRONT PC98 PWR MAIN PWR 1 SATA 0-3 SATA ODD USB 2 FAN CPU HDD LED INTR FAN1 SYS FAN 1 2.5" HDD1-4 3.5" HDD1-2 FAN 2 FAN 3 FAN2 SYS FAN 4 2.5"...
Page 365 System Name: PRIMERGY TX1320 M4 CPU sockets: #PCIe Slots of system: Overview and properties of System PCI devices and slots List of Released Adapters incl. Installation sequence and priority System PCI Slot # M.2 SSD1 M.2 SSD2 PCI Slot attached CPU #...
Page 366 System PCI Slot # M.2 SSD1 M.2 SSD2 CPU1 CPU1 PCI Slot attached CPU # Riser Slot y/n Adapter Installation Sequence Order within Adapter Adapter Class Category Adapter Product Name Max # Category (Cluster) Description (Softwarepool) Adapter M.2 SSD1 M.2 SSD2 PLAN EP MCX4-LX 25Gb 2p SFP28 PLAN EP X710-DA2 2x10Gb SFP+ PLAN EP QL41132 2X 10G SFP+...
Page 367 List of all used screws for PRIMERGY Servers Assembled in Germany and Japan February 2019...
Page 368 / JIS 1012 type A3C40137316 / LSZ: L3-25419-01 hexagon head C26192-Y10-C151 M3 x 3.5 mm 5 mm / cross black 0.6 Nm S301 M3 x 5 mm F6-SW2N3-05121 with spring Phillips PH2 silver 0.6 Nm and washer Copyright 2019 FUJITSU LIMITED...
Page 369 M3 x 6 mm F6-SW2N3-06121 with spring Phillips PH2 silver 0.6 Nm and washer countersink C26192-Y10-C111 M3 x 6 mm silver 0.6 Nm Phillips PH2 S308 countersink F6-SSA3-06121 M3 x 6 mm silver 0.6 Nm Phillips PH2 Copyright 2019 FUJITSU LIMITED...
Page 370 0.6 Nm / JIS 1012 type CA32432-0170 6-32 x 4 mm Knurled screw S506 C26192-Y10-C211 Phillips PH1 black 0.2 Nm M3 x 4.5 mm Knurled screw S507 A3C40218449 Phillips PH1 silver 0.2 Nm M3 x 15 mm Copyright 2019 FUJITSU LIMITED...
Page 371 M2 x 3.5 mm silver 0.2 Nm PDUAL Phillips PH 0 AP200 kit) Denotation scheme S2xx : Screws M2x S3xx : Screws M3x S4xx : Screws M4x S5xx : Screws for special application S6xx : Bolts Copyright 2019 FUJITSU LIMITED...
Page 372 09. November 2018 Bolt and screw for M.2 on board Screw C26361-B443-C220 screw is part of PDUAL AP200 09. January 2019 C26361-Y10-C133 Flat head Kurled screw RAID controller 19. February 2019 : A3C40218449 and RX2530 M5 Copyright 2019 FUJITSU LIMITED...

Fujitsu PRIMERGY TX1320 M4 Upgrade And Maintenance Manual

Version History

1 Introduction

2 Before You Start

3 Important Information

4 Basic Hardware Procedures

5 Basic Software Procedures

6 Power Supply Unit (PSU)

7 Hard Disk Drives (HDD) and Solid State Drives (SSD)

8 Fans

9 Expansion Cards and Backup Units

10 Main Memory

11 Processor (CPU)

12 Accessible Drives

13 Front Panel

14 System Board and Components

Appendix A

Appendix B

Quick Links

Chapters

Related Manuals for Fujitsu PRIMERGY TX1320 M4

Summary of Contents for Fujitsu PRIMERGY TX1320 M4