Motorola MC65 Quick Start Manual

MC65
Note: Remove protective shipping film that covers the touch screen, exit window and camera window
before using.
Quick Start Guide
12
13
1
2
3
4 (Note 1)
14
15
16
17
18
19
20
Note 1: To reset the MC65, simultaneously press the 1 key, 9 key and Power button.
9
3 3 3 3
10
2
2
11 2 4 3 3
4
5 1
1
1 Scan/Action Button 4
2 Up/Down Buttons
3 Microphone 8 6
8 4 Power Buttons
10
9
5 I/O Connector
10
6 Keypad 7
7
7 Scan/Action Button
8 Touch Screen
8
(with screen protector)
9 Scan/Decode LED
10 Charging/Battery
Alpha-Numeric Keypad
Numeric Keypad
Status LED
6 11 WAN Radio Status LED
12 Phone Speaker 1 Talk 6 Orange Key
13 Light Sensor 2 Navigation 7 Backlight
14 Handstrap 3 Soft Key 8 Blue Key
15 Battery 4 Scan/Action Button 9 OK
5 End 10 Start Menu
16 Battery Latch
17 Camera Flash (optional)
18 Camera (optional)
Blue Key Blue Key
19 Exit Window
5 (see Data Capture Options) Use this key to access function keys shown on the keypad Use this key to access function keys shown on the keypad
20 Tether in blue. in blue.
21 Scan/Action Button > Press the Blue key once to activate this state, followed by > Press the Blue key once to activate this state temporarily,
22 Action Button another key. followed by another key.
>
23 Stylus Press the Blue key twice to lock this state.
Orange Key
>
24 Speaker Press the Blue key a third time to unlock.
Use this key to access the secondary layer of characters.
Orange Key
>
Press the Orange key once to lock the keypad into
Use this key to access the secondary layer of characters
Alpha state.
and actions.
>
Press the Orange key a second time to return to the
> Press the Orange key once to activate this state
normal state.
temporarily, followed by another key.
> Press the Orange key twice to lock this state.
> Press the Orange key a third time to unlock.
24
Notifications
23
Data Capture LED:
WAN Radio Status LED:
Red: Scanning active
Green: RF active
Green: Good Decode
Data Capture
22 Message Notification
Charging/Battery Status
Charging/Battery Status LED:
21 WAN Radio Status
Slow blinking amber: Battery charging
Solid amber: Fully charged
Fast blinking amber: Charging error
MicroSD Card Installation Install the Battery
(Optional)
microSD Card Holder
1. Remove the handstrap. 1. Insert the battery, bottom first, into the battery compartment.
2
2. Lift the rubber access door. 2. Press down on the battery until the battery latch snaps
5
3. Slide the SIM card holder up to into place.
SIM Card Holder
unlock. 3. Replace the
handstrap.
4. Lift the SIM card holder.
9
5. Carefully lift the microSD card holder.
6. Insert the microSD card into the
card holder.
Rubber Access Door
6
7
NOTE :
Proper position of the microSD card — the
card connector (i.e., gold contacts) should be
facing out as shown.
Remove the Battery
7. Gently lower the microSD card holder
1. Press and hold the Power button for
until it snaps into place.
approximately 10 seconds.
2. Release the Power button. The Data
SIM Card Installation
(Optional)
Capture LED lights red.
8. Insert the SIM card into the SIM holder. 3. When the LED turns off, remove the
handstrap.
NOTE : 4. Slide the battery latch to the right. The
The proper position of the SIM card—the card battery ejects slightly.
connector (i.e., gold area) should be facing outward 5. Grasp the battery and lift from the MC65.
with the beveled corner facing away.
9. Lower the SIM card holder.
10. Slide the SIM card holder down to lock into place.
11. Close the rubber access door.
2
12. Install the battery.
3
Charge the MC65
Before using the MC65, ensure that the
battery is fully charged.
Use the Single-slot USB cradle,
or Four-slot cradles (Charge Only or
Ethernet) to charge the battery in the MC65.
You can also use the Charge Only and
2
USB/Charging cables to charge the MC65.
1
Charge a spare battery using the
Single-slot cradle.
Charging/Battery Status LED
Slow Blinking Amber = Charging
Solid Amber = Fully charged
Fast Blinking Amber = Charging error
1
Charge the Battery
Use the Four-slot Battery Charger
to charge batteries separately.
2
Note: The 3600 mAh battery charges in less than six hours.
GSM/UMTS Activation
Press the Power button to turn on the MC65.
If a SIM card from a supported carrier is installed, the MC65 detects the installed
activated SIM card and activates on the GSM/UMTS network and configures the
data connections.
If a SIM card from an unsupported carrier is installed, the MC65 detects the
installed activated SIM card and activates on the GSM/UMTS network, but the
data connection and the MMS connection information must be manually
configured.
Refer to the MC65 Integrator Guide for more information.
To activate the MC65 on a CDMA network:
1. Press the Power button to turn on the MC65.
2. Tap Start > Settings > Connections > Phone Network Setup.
3. On the CDMA tab, select a carrier from the preferred network option.
4. Tap the Start Activation button.
5. Tap Yes to activate.
6. Call the carrier from an existing phone to request over-the-air activation.
7. When instructed by the operator press Activate Now button.
For detailed information on activating the MC65, refer to the MC65 Integrator Guide.