Burstner T-Modell 2005 Instruction Manual
  1. Manuals
  2. Brands
  3. Burstner Manuals
  4. Motorhomes
  5. T-Modell 2005
  6. Instruction manual
Burstner T-Modell 2005 Instruction Manual

Burstner T-Modell 2005 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction Manual
Dear Reader ...
1
Instruction Manual
We would like to congratulate you on your purchase of a new Bürstner motorhome. You have se-
lected a top-quality motorhome which will afford you many years of enjoyment.
To enable you to always use and operate your motorhome properly and easily, your Bürstner dealer
will first provide you detailed instructions for all important functions when you take delivery.
This manual, the operating instructions from the base vehicle manufacturer, and the operating in-
structions from the appliance manufacturer will always be at hand to answer any questions you may
have regarding your motorhome.
Before your first journey
Please familiarise yourself with this manual rather than relying on it strictly for reference.
Fill in the warranty cards for the appliances and special equipment in the individual instructions and
send these cards to the respective manufacturers. This ensures your warranty claim for each appli-
ance.
T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T-Modell 2005 and is the answer not in the manual?

Questions and answers

Robert Marrett
April 5, 2025

I'm looking to find the Instruction Manual for a 2002 Burstner T625 Harmony in english . Any help would be greatly appreciated

0

Related Manuals for Burstner T-Modell 2005

Summary of Contents for Burstner T-Modell 2005

  • Page 1 Instruction Manual Dear Reader ... Instruction Manual We would like to congratulate you on your purchase of a new Bürstner motorhome. You have se- lected a top-quality motorhome which will afford you many years of enjoyment. To enable you to always use and operate your motorhome properly and easily, your Bürstner dealer will first provide you detailed instructions for all important functions when you take delivery.
  • Page 2 Instruction Manual T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 3: Table Of Contents

    Contents Introduction ....7 4.6.4 Adjusting the Armrest ..34 Contents General ..... . 8 Seating Arrangement .
  • Page 4 Contents 6.6.6 Roman Shades for Windscreen, Panel (IT 991) ....91 Driver’s Window and Front 8.6.1 V/Tank Gauge for Battery Passenger’s Window ... 60 Voltage and Water or Waste Skylights .
  • Page 5 Contents 9.5.2 Refrigerator (Model RM 7361 12.5 Alde Hot-Water Heater ..162 and RM 7401) ....128 12.5.1 Checking the Fluid Level ..163 9.5.3 Refrigerator 12.5.2...
  • Page 6 Contents 14.6.2 Oxycom ....189 Helpful Notes ....215 14.7 Water Supply .

  • Page 7: Introduction

    Introduction Please read this instruction manual completely before using the vehicle for the first time! Introduction Always keep this instruction manual in the motorhome. Also inform all other users of the safety reg- ulations. The non-observance of this symbol can lead to personal injury. The non-observance of this symbol can lead to damage being caused to, or inside the vehicle.

  • Page 8: General

    Introduction General The motorhome is constructed in accordance with the latest technology and the recognised safety regulations. Nevertheless, personal injury may result and the motorhome may be damaged if the safety instructions in this instruction manual are not followed. Only use the motorhome in a technically impeccable condition. Follow the instructions in the instruc- tion manual.

  • Page 9: Environmental Tips

    Introduction Environmental Tips Be considerate of the environment. Remember that: all kinds of waste water and household waste are not to be disposed of in drains or in the open countryside. Only empty the waste water tank and Thetford cassette at disposal stations, at camp- ing sites or in disposal points which are especially provided for this purpose.
  • Page 10 Introduction T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 11: Safety

    Safety Chapter Overview Safety This chapter contains important safety instructions. The safety instructions are for the protection of persons and property. The instructions address the following topics: fire prevention and what to do in case of fire general care of the motorhome road safety of the motorhome towing gas system of the motorhome...

  • Page 12: General

    Safety General Ensure that there is sufficient ventilation. Never cover or block forced ventilations (skylights) with objects as e. g. a winter mat. Keep forced ventilations clear of snow and leaves. There is a danger of suffocation due to increased CO levels.

  • Page 13: Towing

    Safety Factory-set three-point seat belts must be used when attaching children’s seats. The base vehicle is a commercial vehicle (small truck). Adjust your driving technique accordingly. When driving through underpasses, tunnels, etc. observe the overall height of the motorhome (refer to the technical data in the vehicle documents). In winter, the roof must be free of snow and ice prior to the commencement of the journey.

  • Page 14: Gas Fittings

    Safety Gas Fittings 2.5.1 General Instructions Before commencing the journey, close all gas isolator taps and the regulator tap. Ex- ception: If you plan to use the living area heater during the journey, leave the "Heater" gas isolator tap and the regulator tap open. Have the gas fittings repaired or altered by an authorised workshop only.

  • Page 15: Gas Bottles

    Safety The regulator tap on the gas bottle must be accessible. Only connect gas-operated devices (e. g. gas barbecue) which have been designed for a gas pressure of 30 mbar. The exhaust pipe must be fitted tightly to the heating system and to the chimney and must be sealed.

  • Page 16: Water System

    Safety Water System If the vehicle is not heated when there is risk of frost, empty the entire water system. Leave the water taps on in central position. Leave all drain cocks open. This will avoid frost damage to appliances and to the vehicle. Water left standing in the water tank or in the water pipes becomes undrinkable after a short period.

  • Page 17: Before The Journey

    Before the Journey Chapter Overview Before the Journey This chapter contains important instructions which have to be noted before commencing your jour- ney or carrying out any tasks before the journey. The instructions address the following topics: keys registration calculating the payload correct loading of the motorhome and bike rack towing retracting and extending the entrance step...

  • Page 18: Payload

    Before the Journey Payload Excessive payload and wrong tyre pressure can cause tyre burst. You can lose con- trol over the motorhome. The maximum permissible gross weight stated in the vehicle documents is not to be exceeded by the payload. Built-in accessories, special equipment, the full water tank and the gas bottles all re- duce the payload.

  • Page 19: Calculating The Payload

    Before the Journey 3.3.1 Calculating the Payload Payload calculation is based on part on all-inclusive weights. For safety reasons, the maximum permissible gross weight in a laden condition must not be exceeded. For your own safety, Bürstner recommends to have your completely laden mo- torhome weighed on a public weighbridge before you set out on your journey.
  • Page 20 Before the Journey Example for calculating the basic equipment: Water tank with 120 l 120 kg Gas bottles (2 x 11 kg + 2 x 14 kg + 50 kg bottles Boiler with 12 l + 12 kg 230 V power cable + 4 kg Installation kit for additional battery + 20 kg...
  • Page 21 Before the Journey (3.3) Personal equipment Personal equipment includes all items in the motorhome which do not appear in the list above. These include: - Foodstuffs - Crockery - Television - Radio - Clothes - Bedding - Toys - Books - Toiletries No matter where kept, personal equipment also includes: - Animals...

  • Page 22: Loading The Motorhome Correctly

    Before the Journey 3.3.2 Loading the Motorhome Correctly Distribute the payload evenly between the left-hand and right-hand sides of the vehi- cle. Distribute the payload evenly over both axles, in compliance with the axle loads spec- ified in the vehicle documents. Observe the permissable bearing capacity of the tyres (see chapter 13).

  • Page 23: Roof Rail And Ladder (Partially Special Equipment)

    Before the Journey The weight of the load on the front axle or the rear axle can be calculated with a simple rule of three: The decisive relation is the distance "A" (in cm) from the front axle to each individual payload weight "G"...

  • Page 24: Rear Garage/Rear Storage Space

    Before the Journey Climbing the roof rail: ³ Open the strap (Fig. 1,1) on the ladder at the rear of the vehicle. ³ Fold out the guard rail (Fig. 1,2). ³ Extend the ladder downward. ³ Place guard rail with the rubber knobs (Fig.

  • Page 25: Bike Rack (Special Equipment)

    Before the Journey 3.3.6 Bike Rack (Special Equipment) During the journey, check the secure attachment of the bicycles on the bicycle rack after the first 10 km and then at each break in the journey. The bike rack is only to be loaded with bicycles (max. three pcs.). Driving with a folded out bike rack without bicycles is not permitted.

  • Page 26: Entrance Step

    Before the Journey Entrance Step 3.5.1 Mechanical Entrance Step Make sure that the entrance step (Fig. 3,2) stands on secure and level ground. This will prevent the entrance step from toppling over. Do not step on the edges of the entrance step. Danger of slipping. Secure the entrance step to the ground, for example, with tent pegs.

  • Page 27: Electrically Operated Entrance Step (T-Star, T-Delfin)

    Before the Journey 3.5.2 Electrically Operated Entrance Step (T-Star, T-Delfin) Before commencing the journey, ensure that the entrance step is completely retract- Do not stand in the direct range of the entrance step while it is being retracted or ex- tended.

  • Page 28: Before The Journey

    Before the Journey Extending: ³ Press the switch (Fig. 5,1) situated in the entrance area downwards. Retracting: ³ Press the switch (Fig. 5,1) situated in the entrance area upwards. Follow the warning notice on the entrance step (Fig. 6). Fig. 5 Switch Fig.

  • Page 29: Television (Special Equipment)

    Before the Journey Television (Special Equipment) Before commencing the journey, always store the television in the TV cabinet or re- move it from the support and store it securely. Further information on the TV cabinet can be obtained from chapter 6. Snow Chains (Special Equipment) The use of snow chains is subject the legal regulations of the country you are travelling in.
  • Page 30 Before the Journey Checks Checked Refrigerator set to 12 V operation Children’s seats mounted to seats with three-point seat belts Base vehicle Tyres in proper condition Vehicle lighting, brake lights and reversing lights function Oil levels for engine, gearbox and power steering control- Coolant and fluid for windscreen washers filled up Brakes function Brakes react evenly...

  • Page 31: During The Journey

    During the Journey Chapter Overview During the Journey This chapter contains instructions on how to drive the motorhome. The instructions address the following topics: driving speed brakes seat belts seats and headrests seating arrangement filling the tank Driving the Motorhome At the beginning of every journey and after short interruptions, ensure that the en- trance step is completely retracted.

  • Page 32: Driving Speed

    During the Journey Driving Speed Your motorhome is equipped with a powerful motor, which will provide you with suffi- cient reserves in difficult driving situations. This high power enables a high maximum speed and requires above-average driving ability. Observe the following when driving the motorhome: - The motorhome provides a large contact surface for wind.

  • Page 33: Seat Belts

    During the Journey Seat Belts The motorhome’s living area is equipped with automatic three-point belts. National regulations apply seat-belt fastening. Fasten your seat belts before the beginning of the journey and keep them fastened during the journey. Do not damage or trap belts. Have damaged seat belts changed by an authorised specialist workshop.

  • Page 34: Pilot Seats For The Driver's And Front Passenger's Seats (Partially Special Equipment)

    During the Journey Pilot Seats for the Driver’s and Front Passenger’s Seats (Partially Special Equipment) Before the start of any journey rotate the driver’s seat and the front passenger’s seat so they are facing the direction of vehicle travel and lock them in position. The seats must remain fixed in position during the journey and are not to be rotated.

  • Page 35: Seating Arrangement

    During the Journey Seating Arrangement During the journey, persons are only to be in the prescribed seats. The authorised number of seats is stipulated in the vehicle documents. In seats which are fitted with seat belts, you have to observe seat belt laws.
  • Page 36 During the Journey T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 37: Pitching The Motorhome

    Pitching the Motorhome Chapter Overview Pitching the Motorhome This chapter contains instructions on how to pitch the motorhome. The instructions address the following topics: handbrake wheel chocks entrance step 230 V external connection refrigerator operation of the steady legs Pitch the motorhome so that it is as horizontal as possible. Secure the vehicle to pre- vent it from rolling.

  • Page 38: Steady Legs (Partially Special Equipment)

    Pitching the Motorhome Steady Legs (Partially Special Equipment) Do not use the fitted steady legs as a vehicle jack. The steady legs are only for stabil- ising the pitched motorhome. When pitching, ensure that the steady legs are evenly loaded. Before driving away, wind up the steady legs as far as they can go, fully retract and se- cure them.

  • Page 39: Living

    Living Chapter Overview Living This chapter contains instructions about living in the motorhome. The instructions address the following topics: opening and closing the doors and flaps light switches ventilation of the motorhome opening and closing the windows opening and closing the skylights modifying the table surfaces converting tables use of the beds...

  • Page 40: Conversion Door, Inside (Variant 1)

    Living 6.1.2 Conversion Door, Inside (Variant 1) Opening: ³ Turn the knob in an anticlockwise direction (Fig. 13,1). The lock is unlatched. Locking: ³ Turn the door knob approx. 45° in a clock- wise direction and leave in this position (Fig.

  • Page 41: Conversion Door, Outside (Variant 2)

    Living 6.1.3 Conversion Door, Outside (Variant 2) Opening: ³ Insert into locking cylinder (Fig. 15,1) and turn in an anticlockwise di- rection until the lock is unlatched. ³ Return the key to the central position and remove it. ³ Open the door by pulling on the handle (Fig.

  • Page 42: Window Conversion Door

    Living 6.1.5 Window Conversion Door Depending on the model, the conversion door window is fitted with an insect screen and blind. Opening the window: ³ Press the safety knob (Fig. 17,2) and turn the locking handle (Fig. 17,1) inward. ³ Open all locks.

  • Page 43: External Flaps

    Living External Flaps Before commencing the journey, close all external flaps and lock them. When leaving the motorhome, close all external flaps. Always return the locking cylinder to the initial position. The external flaps fitted to the motorhome are all fitted with identical locking cylinders. Therefore, all locks can be opened with a single key.

  • Page 44: Flap Lock (Variant 2)

    Living 6.2.2 Flap Lock (Variant 2) During rain, water can penetrate the opened flap lock. Therefore close the lock handle (Fig. 20,2) as shown in Fig. 20. Opening: ³ Insert key into locking cylinder (Fig. 20,1) and turn a quarter turn in an anticlockwise direction.

  • Page 45: Flap Lock (Variant 3)

    Living 6.2.3 Flap Lock (Variant 3) Opening: ³ Push the push-button lock (Fig. 21,2). ³ Swing the external flap (Fig. 21,1) upwards. Closing: ³ Swivel the external flap (Fig. 21,1) down- wards and press it shut. Fig. 21 Flap lock (variant 3) 6.2.4 Flap Lock (Variant 4) Opening:...

  • Page 46: Cap For The Fresh Water Filler Neck

    Living 6.2.5 Cap for the Fresh Water Fill- er Neck The fresh water filler neck is la- belled with the word "WASSER" (water) (Fig. 23,1). Opening: ³ Insert key into locking cylinder (Fig. 23,2) and turn it in an anticlockwise direction. ³...

  • Page 47: Furniture Flaps With Handle

    Living 6.3.2 Furniture Flaps with Handle Opening: ³ Pull handle (Fig. 25) until furniture flap is open. Closing: ³ Push down furniture flap until flap hinge per- ceptibly closes. Fig. 25 Furniture flap with handle 6.3.3 Cupboard with Roller Shutter for Flat Screen The cupboard with the roller shutter is in the driver’s cabin on the ceiling.

  • Page 48: Tv Cabinet (Variant 1 And 2)

    Living 6.3.4 TV Cabinet (Variant 1 and 2) Before commencing the journey, always lock the television in the TV cabinet. The television console can be brought into the desired position and fixed there. Positioning: ³ Open TV cabinet. ³ Release the knob (Fig. 27,1 or Fig. 28,1). Fig.

  • Page 49: Tv Cabinet (Variant 3)

    Living 6.3.5 TV Cabinet (Variant 3) Before commencing the journey, always lock the television in the TV cabinet. Positioning: ³ Open TV cabinet. ³ Press latch (Fig. 29,2) and use handle (Fig. 29,1) to pull out extension. ³ Move the swivel console to the desired posi- tion.

  • Page 50: Light Switch

    Living Light Switch 6.4.1 Entrance Area The light switches have different layouts according to the model. The entrance area has light switches for the fol- lowing lighting: Seating group lighting (Fig. 30,1) Awning light (Fig. 30,2, Fig. 30,3 Fig. 31) (partially special equipment) For models without the light Fig.

  • Page 51: Interior

    Living 6.4.2 Interior The light switch for the toilet compartment light- ing is located directly on the corresponding lighting, beneath the mirror (Fig. 32,1) or the toi- let compartment (Fig. 33,1) or in the lower area next to the door (Fig. 34,1). Fig.
  • Page 52 Living The light switches in the living area are located directly on the corresponding lighting (Fig. 35,1 and Fig. 36,1) or in the seating group or the bed area (Fig. 37,1). Fig. 35 Halogen spotlight (variant 1) Fig. 36 Halogen spotlight (variant 2) Fig.

  • Page 53: Ventilation

    Living Ventilation The oxygen in the vehicle interior is used up by breathing or the use of the gas cooker etc. and must therefore be continuously replaced. For this reason the motorhome features forced ventilations (skylights). Never cover or block forced ventilations with objects as e.

  • Page 54: Hinged Window With Rotary Hinges

    Living 6.6.1 Hinged Window with Rotary Hinges When opening the hinged win- dows, ensure that there are no torsional forces. Open and close the hinged windows evenly. If the catch lever is equipped with a safety knob, press the safety knob when operating the catch le- ver.
  • Page 55 Living Continuous ventilation: With the catch lever, the hinged window can be placed in 2 positions: Continuous ventilation (Fig. 41 or Fig. 42) firmly closed. To place the hinged window into the "continu- ous ventilation" position: ³ necessary, press safety knob (Fig.

  • Page 56: Hinged Window With Automatic Hinges

    Living 6.6.2 Hinged Window with Auto- matic Hinges Windows with engaging struts must be opened completely in or- der to release the lock. If the lock- ing device is not released and the window is closed nevertheless, there is the danger of the window being torn due to the massive counter-pressure.

  • Page 57: Sliding Window

    Living Continuous ventilation: With the catch lever, the hinged window can be placed in two positions: Continuous ventilation (Fig. 46 or Fig. 47) firmly closed. To place the hinged window into the "continu- ous ventilation" position: ³ necessary, press safety knob (Fig.

  • Page 58: Blind And Insect Screen (Variant 1)

    Living 6.6.4 Blind and Insect Screen (Variant 1) The windows in the motorhome are fitted with a blind and an insect screen. The blind and insect screen can be adjusted separately. Blind and insect screen are located in the top blind box. Blind Closing: ³...

  • Page 59: Blind And Insect Screen (Variant 2)

    Living 6.6.5 Blind and Insect Screen (Variant 2) The windows in the motorhome are fitted with a blind and an insect screen. The blind and insect screen can be adjusted separately. The insect screen is located in the top blind box, the blind is in the bottom blind box.

  • Page 60: Roman Shades For Windscreen, Driver's Window And Front Passenger's Window

    Living 6.6.6 Roman Shades for Wind- screen, Driver’s Window and Front Passenger’s Window Closing: ³ Pull the guide (Fig. 52,1) for the roman shade for the windscreen from the holder (Fig. 52,2) above the windscreen. ³ Grasp the handle of the Roman shades and draw carefully until the magnetic catch keeps the Roman shades closed.

  • Page 61: Skylights

    Living Skylights The apertures for forced ventilation must always be kept open. Never cover or block forced ventilations with objects as e. g. a winter mat. Keep forced ventilations clear of snow and leaves. The skylights are fitted with a Roman shade and an insect screen. After the latch has been released, the insect screen automatically springs back to the initial position by tensile force.

  • Page 62: Hinged Skylight

    Living 6.7.1 Hinged Skylight The hinged skylight may be opened on one side only. Three inclination angles may be used. An extension hook can be found in the entrance area. ³ In order to open the skylight (Fig. 54,3), rotate the lever anticlockwise one quarter-turn and use lever to press the hinged skylight upwards.

  • Page 63: Lift-Tilt Skylight

    Living 6.7.2 Lift-Tilt Skylight Do not stand on the acrylic glass of the lift-tilt skylight. Before commencing the journey, check that the lift-tilt skylight is closed and locked. The lift-tilt skylight is not to be opened or closed during the journey. The lift-tilt skylight can be opened using the manual crank.

  • Page 64: Tables

    Living Tables 6.8.1 Suspension Table (Variant 1) The suspension table may also be used as a bed foundation. Conversion to bed foundation: ³ Slightly lift the front of the table-top. ³ Move the locking device (Fig. 56,4) toward the table-top. ³...

  • Page 65: Suspension Table (Variant 2)

    Living 6.8.2 Suspension Table (Variant 2) The suspension table size can be enlarged by inserting a table-top extension. Extending: ³ Open catches (Fig. 59,1). ³ Slightly lift the front of the table-top (Fig. 58,2). ³ Pull out the table-top as far as it can go. ³...

  • Page 66: Swivel Table

    Living 6.8.3 Swivel Table Before commencing the journey, reduce the size of the swivel table and secure it. The swivel table size can be enlarged by un- folding the table-top extension. Extending: ³ Place lever (Fig. 61,1) in a vertical position. ³...

  • Page 67: Fixed Table

    Living 6.8.4 Fixed Table The fixed table cannot be used as a bed foun- dation. Extending: ³ Pull locking lever (Fig. 64,1) and swing out the table-top extension. Reducing size: ³ Swing back the table-top extension until the locking lever is engaged. Fig.

  • Page 68: Converting Seating Groups For Sleeping

    Living 6.10 Converting Seating Groups for Sleeping 6.10.1 Central Seating Group (Variant 1) ³ Convert the table (Fig. 66,3) into a bed foundation (see section 6.8). ³ Pull bedding extension (Fig. 66,5). Fig. 66 Prior to conversion ³ Place the back cushions (Fig. 66,1) and the seat cushions (Fig.

  • Page 69: Central Seating Group (Variant 2)

    Living 6.10.2 Central Seating Group (Variant 2) ³ Convert the table (Fig. 69,3) into a bed foundation (see section 6.8). Fig. 69 Prior to conversion ³ Pull the seat cushions (Fig. 70,2) into the centre. ³ Insert the back cushions (Fig. 70,1) be- tween the seat cushions and the wall.

  • Page 70: Central Seating Group With

    Living 6.10.3 Central Seating Group with Divan (Variant 1) ³ Convert the table (Fig. 71,3) into a bed foundation (see section 6.8). ³ Lay the back cushion (Fig. 71,1) aside. Fig. 71 Prior to conversion ³ Place the seat cushion (Fig. 72,2) on the ta- ble.

  • Page 71: Central Seating Group With Divan (Variant 2)

    Living 6.10.4 Central Seating Group with Divan (Variant 2) ³ Convert the table (Fig. 74,3) into a bed foundation (see section 6.8). ³ Lay the back cushion (Fig. 74,1) aside. Fig. 74 Prior to conversion ³ Place the seat cushion (Fig. 75,2) on the ta- ble.

  • Page 72: Central Seating Group With Divan (Variant 3)

    Living 6.10.5 Central Seating Group with Divan (Variant 3) ³ Convert the table (Fig. 77,3) into a bed foundation (see section 6.8). ³ Place the back cushion (Fig. 77,1) and the seat cushion (Fig. 77,2) to the side. Fig. 77 Prior to conversion ³...

  • Page 73: Central Seating Group With Divan (Variant 4)

    Living 6.10.6 Central Seating Group with Divan (Variant 4) ³ Convert the table (Fig. 80,3) into a bed foundation (see section 6.8). ³ Lay the back cushion (Fig. 80,1) aside. Fig. 80 Prior to conversion ³ Place the additional cushion (Fig. 81,7) on the table.
  • Page 74 Living T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 75: Gas Fittings

    Gas Fittings Chapter Overview Gas Fittings This chapter contains instructions regarding the gas fittings of the motorhome. The instructions address the following topics: safety changing the gas bottles gas isolator taps external gas connection Duomatic switching facility The operation of the gas operation appliances of the motorhome is described in chapter 9. General Before commencing the journey, close all gas isolator taps and the regulator tap.
  • Page 76 Gas Fittings Regularly inspect the gas tube fitted to the gas bottle connection for tightness. The gas tube must not have any tears and must not be porous. Have the gas tube re- placed in an authorised workshop no later than ten years after the manufacturing date.

  • Page 77: Gas Bottles

    Gas Fittings Gas Bottles Gas bottles are only to be transported within the designated gas bottle compartment. Secure gas bottles in the gas bottle compartment in a vertical position and so that they are unable to turn. Close the regulator tap on the gas bottle before the gas pressure regulator or gas tube are removed from the gas bottle.

  • Page 78: Changing Gas Bottles

    Gas Fittings Changing Gas Bottles When changing gas bottles, do not smoke or create any open fire. When you have changed the gas bottle, check whether gas escapes at the connec- tion points and unions. Use a leakage search spray to spray the relevant connection point or union.

  • Page 79: External Gas Connection (Special Equipment)

    Gas Fittings External Gas Connection (Special Equipment) If the external gas connection is not in use, always close the stopcock (Fig. 85,2). Only gas appliances with a suitable adapter should be connected to the external gas connection. Connect only external gas appliances which are designed for an operation pressure of 30 mbar.

  • Page 80: Duomatic Switching Facility (Special Equipment)

    Gas Fittings Duomatic Switching Facility (Special Equipment) Do not use the Duomatic switching facility in closed spaces. The Duomatic is an automatic switching facility with a remote display for a two-bottle gas system. The Duomatic switching facility automatically switches gas feed from the primary bottle to the re- serve bottle as soon as the primary bottle is either empty or no longer ready for operation.
  • Page 81 Gas Fittings Changing gas bottles When changing gas bottles, do not smoke or light any open flames! Always mount the regulator in such a way that the protective cap faces upwards. If an indicator lamp goes out during operation, this signifies that the corresponding gas bottle is emp- ty and must be replaced.
  • Page 82 Gas Fittings T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 83: Electrical Fittings

    Electrical Fittings Chapter Overview Electrical Fittings This chapter contains instructions regarding the electrical fittings of the motorhome. The instructions address the following topics: safety explanations of terms relating to the battery starter battery living area battery transformer/rectifier power pack connection to the 230 V power supply panel electrical wiring Operation of the electric appliances of the motorhome is described in chapter 9.

  • Page 84: Power Supply

    Electrical Fittings Capacity Capacity refers to the amount of electricity which can be stored in a battery. The capacity of a battery is given in ampere hours (Ah). If a battery possesses a capacity of 90 Ah, then the battery can dispense a current of 1 A for 90 hours or a current of 2 A for 45 hours. External influences such as temperature may alter the storage capacity of the battery.

  • Page 85: Living Area Battery

    Electrical Fittings The starter battery can only be fully charged with an external charger. If a 230 V power supply is used, the transformer/rectifier charges the starter battery with a float charge only. Even in mobile op- eration, the vehicle engine alternator is not capable of completely charging the starter battery. When charging the starter battery with an external charger, proceed as follows: ³...
  • Page 86 Electrical Fittings Do not run the engine with the living area battery disconnected. Danger of short circuit! Take note of the battery manufacturers users and maintenance instructions. Devices with a maximum of 10 A can be connected to the sockets of the 12 V power supply.

  • Page 87: Transformer/Rectifier (Ebl 99)

    Electrical Fittings Transformer/Rectifier (EBL 99) Do not cover the ventilation slots of the transformer/rectifier. Danger of overheating! Fig. 88 Transformer/rectifier (EBL 99) 1 Main supply socket 230 V~ 7 Output: block 6 - solar charge regulator (if fitted) 2 Output: block 1 - refrigerator 8 Output: block 7 - auxiliary charging unit 3 Output: block 2 - alternator D+ 9 Output: block 8 - consumer circuit 1, consumer...

  • Page 88: Battery Cut-Off Switch

    Electrical Fittings 8.4.1 Battery Cut-Off Switch The battery cut-off switch (Fig. 88,12) disconnects all the living area 12 V appliances, even the safe- ty/drainage valve. This prevents the living area battery from slowly discharging if the motorhome is not used for a longer period of time (e. g. temporary lay-up). The batteries can still be charged by the transformer/rectifier when the battery cut-off switch is turned off.

  • Page 89: Transformer/Rectifier (E-Box)

    Electrical Fittings Transformer/Rectifier (E-Box) Do not cover the ventilation slots of the transformer/rectifier. Danger of overheating! Duty of the transformer/rectifier The transformer/rectifier charges the living area battery. The transformer/rectifier charges the starter battery with a float charge only. The transformer/rectifier monitors the voltage in the living area battery. The transformer/rectifier distributes the current to the 12 V circuits and secures them.

  • Page 90: Main Switch

    Electrical Fittings 8.5.1 Main Switch The main switch (Fig. 89,4) disconnects all the living area 12 V appliances, even the safety/drainage valve. This prevents the living area battery from slowly discharging if the motorhome is not used for a longer period of time (e. g. temporary lay-up). The batteries can still be charged by the transformer/rectifier when the main switch is turned off.

  • Page 91: Panel (It 991)

    Electrical Fittings Panel (IT 991) Fig. 90 Panel (IT 991) 1 V/tank gauge 9 Setting the digital clock - minutes 2 Display digital clock/temperature 10 Setting the digital clock - hours 3 Current gauge 11 Rocker switch for digital clock on/off 4 Indicator lamp for the 12 V power supply 12 Rocker switch for calling up the level in the water or 5 12 V main switch...
  • Page 92 Electrical Fittings The table below will help you correctly interpret the displayed battery voltage of the living area bat- tery. Battery voltage Battery operation Mobile operation Power operation (values under vehicle stationary, vehicle moving, vehicle stationary, operation, not no 230 V connection no 230 V connection 230 V connection for off-load volt-...

  • Page 93: Display Digital Clock/Temperature

    Electrical Fittings Battery alarm for the living area battery The red ALARM warning light (Fig. 90,13) flashes as soon as the voltage of the living area battery falls below 11 V (measured under operation) and there is the threat of a total discharge. When the battery alarm comes on, switch off the appliances and completely charge the living area battery, either by mobile operation or by connection to a 230 V power supply.

  • Page 94: Current Gauge For Charging/Discharging The Living Area Battery

    Electrical Fittings Temperature display The temperature display is only operational when the digital clock display is switched on. After a reading, the respective temperature will be displayed for approx. 6 seconds. ³ Press the upper part of rocker switch °C (Fig. 90,8) : internal temperature is displayed.

  • Page 95: Main Switch

    Electrical Fittings 8.6.4 12 V Main Switch The 12 V main switch (Fig. 90,5) switches the 12 V power supply to the living area on and off. Exception: heating, basic light (lighting in the entrance area) entrance step and spare 4 on the trans- former/rectifier are always ready to operate.

  • Page 96: Docking Station

    Electrical Fittings 8.7.1 Docking Station If the panel is not connected to the docking station, a button cell sup- plies power for a short while (bat- tery type: Lithium-manganese, 3 V, 180 mA). Therefore never separate the panel from the dock- ing station for long periods.

  • Page 97: Lcd Display And Operation

    Electrical Fittings Turning on: ³ Press the rotary knob (Fig. 91,2): the 12 V living area power supply is switched on. The LCD dis- play shows the current condition data and is lit for approx. 15 seconds. Additionally, in the event of an alarm, the relevant alarm display appears.
  • Page 98 Electrical Fittings In the following table, the symbols, their meaning and their function are listed: Symbol Signification/menu Functions Light On, off, timer active Water pump On, off, timer active Starter battery Status call up Living area battery Status call up Water tank Level indicator Waste water tank...

  • Page 99: Power Supply

    Electrical Fittings 230 V Power Supply Only allow qualified personnel to work on the electrical fittings. Only replace defective fuses when the cause of the defect is known and has been remedied. The 230 V power supply provides electricity for: sockets with earth contact for appliances with maximum 16 A refrigerator transformer/rectifier...

  • Page 100: Power Cable For External 230 V Connection

    Electrical Fittings 8.8.2 Power Cable for External 230 V Connection Completely unwind the cable reels. Power cable: three-core (3 x 2.5 mm ) flexible rubber sheathed cable maximum 25 m in length 1 plug with earth contact 1 socket with earth contact For your power cable, Bürstner recommends using a CEE connection cable with a CEE plug and coupling.

  • Page 101: Fuses

    Electrical Fittings Fuses Only replace defective fuses when the cause of the defect is known and has been remedied. Never bridge or repair fuses. 8.9.1 Fuses 12 V The appliances connected to the 12 V power supply in the living area are fused individually. The fuses are accessible in the engine com- partment, in the driver’s cabin, at the living area Fig.
  • Page 102 Electrical Fittings Fuses on the transformer/rectifier (EBL 99) FuNo Function Value/colour Heater 5 A/brown Basic light/electrically operated entrance step/radio 25 A/white Spare 4 25 A/white Spare 3 25 A/white Spare 2 15 A/blue Spare 1 15 A/blue Solar 10 A/red Spare 5 15 A/blue Spare 6...

  • Page 103: Fuse 230 V

    Electrical Fittings Thetford cassette fuse The fuse (Fig. 99,1) is located on the left-hand locker wall of the Thetford cassette. Type of fuse: flat fuse 3 A/purple. To change the fuse, open the Thetford cassette flap on the outside and pull out the Thetford cassette completely.

  • Page 104: Circuit Diagram

    Electrical Fittings 8.10 Circuit Diagram 8.10.1 Circuit Diagram, Interior Fig. 101 Circuit diagram, interior (EBL 99) T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...
  • Page 105 Electrical Fittings Fig. 102 Circuit diagram, interior (E-Box) T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...
  • Page 106 Electrical Fittings Fig. 103 Circuit diagram, panel (IT 991) T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 107: Circuit Diagram, Exterior

    Electrical Fittings 8.10.2 Circuit Diagram, Exterior Fig. 104 Circuit diagram, exterior Side Colours Colours Colours Colours Connection Fiat/Citroen/Peugeot Mercedes-Benz Renault Bürstner Left Blue-black contact BL Black-yellow Grey Yellow Left direction indicator Grey-yellow contact S Grey-black Pink Blue Fog tail light Black contact 31 Brown Black...
  • Page 108 Electrical Fittings T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 109: Appliances

    Appliances Chapter Overview Appliances This chapter contains instructions regarding the appliances of the motorhome. The instructions refer exclusively to the operation of the appliances. Further information about the appliances can be found in the instruction manuals for the apliances, included separately with the vehicle. The instructions address the following topics: heater boiler...

  • Page 110: Heater

    Appliances Heater Never let gas escape unburned due to danger of explosion. When filling the fuel tank, on ferries or in the garage, the heater must be turned off. Danger of explosion! Models with waste gas vent on the right-hand side of the vehicle: if the awning is put up and the heater is switched on, exhaust gases from the heater may build up in the awning.

  • Page 111: Trumatic C Hot-Air Heater

    Appliances 9.2.2 Trumatic C Hot-Air Heater Empty the heating system when there is a danger of frost the heater is not in opera- tion. Do not use the space above and behind the Trumatic C hot-air heater for storage. The hot-air heater has two operating modes: Winter operation Summer operation Heating is only possible on "Winter"...

  • Page 112: Alde Hot-Water Heater (Special Equipment)

    Appliances Turning off: ³ Set rotary switch (Fig. 106,3) to "Off" (Fig. 106,4). ³ When not in use for an extended period, close the regulator tap on the gas bottle and the gas isolator tap "Heater/boiler". After switching off the heater, the circulating fan may still run for a moment to use up the residual heat.
  • Page 113 Appliances Gas operation Turning on: ³ Open the regulator tap on the gas bottle and the gas isolator tap "Heater/boiler". ³ Set sliding switch (Fig. 107,3) to gas operation. ³ Turn temperature control knob (Fig. 107,8) to the required heating level. ³...
  • Page 114 Appliances Alde heat exchanger (special equipment) The heat exchanger only works when the vehicle engine is run- ning. If the heat exchanger is not being used (as in the summer), the heat exchanger on the stop cock should be shut off. The heat exchanger can be used to heat the motorhome living area during travel without op- erating the hot-water heater in the living area.
  • Page 115 Appliances Alde auxiliary circulating pump (special equipment) The auxiliary circulating pump works only where a heat exchang- er has been installed and when the hot-water heater is running. The auxiliary circulating pump (Fig. 109,1) can be used to heat the motorhome engine when parked.

  • Page 116: Auxiliary Heat Exchanger (Special Equipment)

    Appliances 9.2.4 Auxiliary Heat Exchanger (Special Equipment) The heat exchanger only works when the vehicle engine is running. If the heat exchanger is not being used (as in the summer), the heat exchanger on the control knob should be shut off. The auxiliary heat exchanger (Fig.

  • Page 117: Floor Heating (Special Equipment)

    Appliances 9.2.5 Floor Heating (Special Equipment) On models with floor heating, do not drill holes in the floor or screw in any screws. There is danger of a power cut or a short circuit due to damage to a heater wire. The floor heating only functions when the vehicle is connected to a 230 V power sup- ply.

  • Page 118: Boiler

    Appliances Boiler 9.3.1 Trumatic C Boiler Never let gas escape unburned due to danger of explosion. When filling the fuel tank, on ferries or in the garage, the boiler must be turned off. Danger of explosion! Models with waste gas vent on the right-hand side of the vehicle: if the awning is put up and the boiler is switched on, exhaust gases from the boiler may build up in the awning.
  • Page 119 Appliances Safety/drainage valve boiler The boiler is equipped with a safety/drainage valve (Fig. 117). The safety/drainage valve pre- vents water in the boiler from freezing, when there is frost and the heater is not switched on. When the safety/drainage valve is closed a small electrical power flows which puts an extra load on the battery of the living area.

  • Page 120: Alde Boiler (Special Equipment)

    Appliances Emptying: ³ Set the rotary switch (Fig. 116,2) on the operating unit (Fig. 116) to "OFF". ³ Open the safety/drainage valve (Fig. 117). Push the pull switch (Fig. 117,1) down. The boiler is drained to the outside by the safety/drainage valve. ³...
  • Page 121 Appliances Filling with water: ³ Close the drain cocks. Position the rocking lever (Fig. 119,1) horizontally. ³ Switch the 12 V power supply on. ³ Open all water taps and set to "Warm" posi- tion. Water pump is pumping water into the boiler.
  • Page 122 Appliances Gas and electrical operation Turning on: ³ Open the regulator tap on the gas bottle and the gas isolator tap "Heater/boiler". ³ Set sliding switch (Fig. 118,1) to electrical operation. ³ Set sliding switch (Fig. 118,3) to gas operation. ³...

  • Page 123: Cooker

    Appliances Cooker Never let gas escape unburned due to danger of explosion. Before using the cooker make sure that there is sufficient ventilation. Open windows or the skylight. Do not use gas cooker or gas oven for heating. Always protect your hands with cooking gloves or potholders when handling hot pots, pans and similar items.
  • Page 124 Appliances Turning on: ³ Open the regulator tap on the gas bottle and the gas isolator tap "Cooker". ³ Open the gas cooker lid (Fig. 120,3) and, depending on the model, open out the flame protection (Fig. 120,1). ³ Turn the control knob (Fig. 120,2) on the burner you wish to use to the ignition posi- tion (large flame).

  • Page 125: Gas Oven (Partially Special Equipment)

    Appliances 9.4.2 Gas Oven (Partially Special Equipment) Always keep ventilation apertures open. There must be no flammable objects near the gas oven when it is being lit. The oven flap must remain open when it is being lit. If ignition has not taken place, repeat the entire procedure. If necessary, check if there is gas/and or current in the gas oven.
  • Page 126 Appliances Lighting units which have a thermostat: The lighting position is reached by turning the control knob to a position between 1 and ³ Open oven door completely. ³ Lightly press control knob down, turn to the ignition position and hold for 5 to 10 seconds. ³...

  • Page 127: Microwave Oven (Special Equipment)

    Appliances 9.4.3 Microwave Oven (Special Equipment) Only qualified personnel may repair the microwave oven. Improper repairs can cause major risks to the user. The protection device against the escape of microwave energy should never be re- moved. Use the microwave oven only if it has been properly installed. Only use the microwave oven when the door seal is free of damage.

  • Page 128: Refrigerator

    Appliances Refrigerator While driving, only operate the refrigerator via the 12 V power supply. At temperatures above +40 °C full cooling power is not possible. When outside temperatures are high, full cooling pow- er of the cooling unit is only guaranteed by suf- ficient ventilation.
  • Page 129 Appliances Turning on: ³ Open the regulator tap on the gas bottle and the gas isolator tap "Refrigerator". ³ Set the energy selector switch (Fig. 125,1) to "GAS". ³ Set the control knob (Fig. 125,5) to maxi- mum power. Gas supply is open. Ignition will take place automatically.

  • Page 130: Refrigerator (Model Rm 7655)

    Appliances 9.5.3 Refrigerator (Model RM 7655) Volume Model RM 7655: 150 l Never let gas escape unburned due to danger of explosion. If the frame heater is switched on, it will always consume current. Therefore, switch off the frame heater if the vehicle engine is off and the vehicle is not connected to the 230 V power supply.
  • Page 131 Appliances Gas operation If the 230 V power supply is disconnected and the vehicle’s engine is not running the "AES" selects the gas supply. When selecting gas operation the ignition fuse is opened automatically so gas can get into the burner. At the same time the electronic ignition is activated. If the gas flame is extin- guished, e.

  • Page 132: Refrigerator Door Locking Mechanism

    Appliances 9.5.4 Refrigerator Door Locking Mechanism Opening and closing the refrigerator door (RM 7361 and RM 7401) There are two positions for locking the refrigerator door in place: closed refrigerator door during travel and when the refrigerator is in operation slightly opened refrigerator door as a ventilation position when the refrigerator is switched off Opening: ³...
  • Page 133 Appliances Opening and closing the refrigerator door/freezer compartment (RM 7655) During the journey, the refrigerator door/freezer compartment must always remain closed and locked. There are two positions for locking the refrigerator door in place: closed refrigerator door during travel and when the refrigerator is in operation slightly opened refrigerator door as a ventilation position when the refrigerator is switched off Opening: ³...
  • Page 134 Appliances T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 135: Sanitary Fittings

    Sanitary Fittings Chapter Overview Sanitary Fittings This chapter contains instructions regarding the sanitary fittings of the motorhome. The instructions address the following topics: water tank complete water system waste water tank waste water tank heater toilet compartment toilet 10.1 Water Supply, General Fill the water tank with fresh water only.

  • Page 136: Fresh Water Filler Neck

    Sanitary Fittings 10.2.2 Fresh Water Filler Neck The fresh water filler neck is on the right or left side of the motorhome, depending on the model. The fresh water filler neck is labelled with the word "WASSER" (water) (Fig. 131,1). The cap is open or closed using the key for the external flap locks.

  • Page 137: Filling The Water System

    Sanitary Fittings 10.3 Filling the Water System When filling the water tank, observe the maximum permissible gross weight of the motorhome. Never operate water pump without water. The Truma system (heater/boiler) has an electric safety/drainage valve and a drain cock (yellow) for emptying. The Alde system (heater/boiler) has two drain cocks (yellow) for emptying.

  • Page 138: Emptying The Water System

    Sanitary Fittings ³ Keep the taps op until the water flowing out of the taps has no bubbles in it. This is the only way to ensure that the boiler is also full of water. ³ Set all water taps to "Cold" and leave them on. This will fill the cold water pipes with water. ³...

  • Page 139: Waste Water Tank

    Sanitary Fittings 10.5 Waste Water Tank 10.5.1 All Models Except Delfin Performance In case of frost add so much anti-freeze (such as kitchen salt) to the waste water tank so that the waste water cannot freeze. Never pour boiling water directly into the sink outlet. Boiling water could cause defor- mation and leaks in the waste water pipe system.

  • Page 140: Delfin Performance

    Sanitary Fittings 10.5.2 Delfin Performance If the living area heater is out of order, the waste water tank no longer is sufficiently protected against frost. In case of frost add so much anti-freeze (such as kitchen salt) to the waste water tank so that the waste water cannot freeze. Never pour boiling water directly into the sink outlet.

  • Page 141: Waste Water Tank Heater

    Sanitary Fittings 10.6 Waste Water Tank Heater (Special Equipment) The waste water tank may be heated and is in- sulated. The integrated frost guard prevents waste water from freezing. A switch (Fig. 138,1) on the front of the bench seat or bed may be used to switch the frost guard on and off.

  • Page 142: Swivel Toilet

    Sanitary Fittings 10.8.1 Swivel Toilet Preparing toilet: ³ Open flap for the Thetford cassette and pull retaining clip upwards to remove Thetford cassette. The Thetford cassette may only be removed when the sliding trap is closed. Fig. 139 Pulling the retaining clip ³...
  • Page 143 Sanitary Fittings Never put the sanitary liquid di- rectly in the toilet bowl. ³ Fill the Thetford cassette with the specified quantity of sanitary liquid. ³ Then add enough water to completely cover the bottom of the Thetford cassette. ³ Close the drainage neck with the cap.
  • Page 144 Sanitary Fittings Use: ³ Move the toilet bowl into a convenient posi- tion. Fig. 145 Rotating the toilet bowl ³ Fill the toilet bowl with some water. Press the flush button. Flushing continues as long as the button is pressed. ³...
  • Page 145 Sanitary Fittings ³ Flush the toilet. Press the flush button. ³ After flushing close the sliding trap again. Fig. 148 Operating the flush Cassette C-200 E: ³ Open the sliding trap. To do this, press the left side of the sliding trap button. Fig.
  • Page 146 Sanitary Fittings Emptying the Thetford cassette: ³ Open flap for the Thetford cassette and pull retaining clip upwards to remove Thetford cassette. The Thetford cassette may only be removed when the sliding trap is closed. ³ Pull out the Thetford cassette as far as it can go.

  • Page 147: Toilet With Fixed Seat

    Sanitary Fittings 10.8.2 Toilet with Fixed Seat Preparing toilet: ³ Open flap for the Thetford cassette and press securing clip downwards to remove Thetford cassette. Fig. 154 Releasing securing clip ³ Pull out the Thetford cassette as far as it can go.
  • Page 148 Sanitary Fittings Never put the sanitary liquid di- rectly in the toilet bowl. ³ Fill the Thetford cassette with the specified quantity of sanitary liquid. ³ Then add enough water to completely cover the bottom of the Thetford cassette. ³ Close the drainage neck with the cap.
  • Page 149 Sanitary Fittings ³ Rinse the toilet bowl with water. To do so, press flush button and at the same time ro- tate in an anticlockwise direction. The rotary movement causes the sliding trap to open. The toilet bowl is rinsed out thoroughly. ³...
  • Page 150 Sanitary Fittings Emptying the Thetford cassette: ³ Open flap for the Thetford cassette and press securing clip downwards to remove Thetford cassette. ³ Pull out the Thetford cassette as far as it can go. ³ Tip the Thetford cassette slightly and then pull it out completely.
  • Page 151 Sanitary Fittings ³ Return the Thetford cassette to its original location. As you do so, push the Thetford cassette in until the securing clip holds the Thetford cassette in place. ³ Reclose the flap for the Thetford cassette. Fig. 166 Inserting the Thetford cassette T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...
  • Page 152 Sanitary Fittings T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 153: Care

    Care Chapter Overview Care This chapter contains instructions regarding the care of the motorhome. The maintenance instructions address the following topics: exterior of the motorhome interior winter operation At the end of the chapter there is a checklist of measures you must carry out if you are not going to use the motorhome for an extended period of time.

  • Page 154: Windows Of Acrylic Glass

    Care 11.1.2 Windows of Acrylic Glass Acrylic glass windows are delicate and require very careful handling. Never rub when dry as dust particles might damage the surface! Only clean with plenty of warm water, dish washing liquid and soft cloth. Never use glass cleaning agents with chemical, abrasive or alcohol-containing addi- tives.

  • Page 155: Waste Water Tank

    Care 11.1.5 Waste Water Tank Clean the waste water tank after every use of the motorhome. ³ Open the cleaning opening on the waste water tank and the drain cock. ³ Rinse thoroughly with fresh water. 11.1.6 Entrance Step If the entrance step is lubricated, coarse particles of dirt can settle on the lubricant during the journey and cause damage to the operating mechanism of the entrance step.

  • Page 156: Winter Care

    Care ³ Brush Roman shades with a soft brush or vacuum with the brush attachment of the vacuum cleaner. ³ Brush blinds on windows with a soft brush. Grease or stubborn dirt may be removed with a mild soap at 30 °C (curd soap). ³...

  • Page 157: Lay-Up

    Care 11.4 Lay-Up 11.4.1 Temporary Lay-Up After the vehicle has been standing for a longer period (approx. 10 months) have the braking and gas systems checked by an authorised specialist workshop. Take into consideration that water is undrinkable after only a short time. Before laying up the vehicle, go through the following check list: Activities Done...

  • Page 158: Winter Lay-Up

    Care 11.4.2 Winter Lay-Up Additional measures are required if laying up the vehicle over winter: Activities Done Base vehicle Clean body and underbody thoroughly and spray with hot wax or protect with varnish Fill fuel tank with winter diesel Check antifreeze in the cooling water Rectify damage to the paintwork Body Keep the forced ventilation open...

  • Page 159: Starting Up The Vehicle After A Temporary Lay-Up Or After Lay-Up Over Winter

    Care 11.4.3 Starting Up the Vehicle after a Temporary Lay-Up or after Lay-Up over Winter Go through the following check list before start-up: Activities Done Base vehicle Check the tyre pressure on all tyres Check the tyre pressure of the spare wheel Body Clean the pivot bearing of the entrance step Check the functioning of the fitted steady legs...
  • Page 160 Care T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 161: Maintenance

    Maintenance Chapter Overview Maintenance This chapter contains instructions about inspection and maintenance work concerning the vehicle. The maintenance instructions address the following topics: doors living area battery Alde hot-water heater Oxycom air conditioning unit replacing light bulbs At the end of the chapter you will find important instructions on how to obtain spare parts. 12.1 Inspection Work Like any technical appliance, the vehicle must be inspected at regular intervals.

  • Page 162: Living Area Battery

    Maintenance 12.4 Living Area Battery When replacing the battery, only use the same type of battery (same capacity and voltage, cycle stability). Never use conventional car batteries (starter batteries). A lead acid battery must not be replaced by a lead gel battery. Do not use so-called improvers.

  • Page 163: Checking The Fluid Level

    Maintenance 12.5.1 Checking the Fluid Level ³ Check to see if the hot-water heater can be switched off and cooled. ³ Check if the fluid level is between the marks "MIN" and "MAX" on the compensator reservoir (Fig. 167). 12.5.2 Topping up Heating Fluid Place the vehicle in a horizontal position to avoid the formation of bubbles.

  • Page 164: Oxycom Air Conditioning Unit

    Maintenance 12.6 Oxycom Air Conditioning Unit 12.6.1 Replacing the Air Filter ³ Push the lattice frame (Fig. 169,3) in the di- rection of the operating panel (Fig. 169,4) and pull down. ³ Remove lattice frame. ³ Remove filter brackets. ³ Remove filter.

  • Page 165: Replacing Bulbs, External

    Maintenance 12.7 Replacing Bulbs, External Bulbs and light fittings can be extremely hot. Therefore, allow lights to cool down be- fore changing bulbs. Store bulbs in a safe place inaccessible to children. Do not use any bulb that has been dropped or which shows scratches in its glass. The bulb might burst.

  • Page 166: Side Lights

    Maintenance Variant 2 ³ Use a suitable tool to remove the inner sec- tion of the screw covers (Fig. 173,1). ³ Remove the screw underneath the cover. ³ Completely remove lamp holder (Fig. 173,3). As you do so, pay attention to the cable connections.

  • Page 167: Types Of Bulbs For Exterior Lighting

    Maintenance 12.7.4 Types of Bulbs for Exterior Lighting Exterior lighting Type of bulb Rear Brake light/rear light Ba15d 12 V 21/5 W Direction indicator Ba15s 12 V 21 W Fog tail light Ba15s 12 V 21 W Licence plate light Soffitte 12 V 5 W Reversing light Ba15s 12 V 21 W...

  • Page 168: Halogen Spotlights (Variant 1)

    Maintenance 12.8.2 Halogen Spotlights (Variant 1) Halogen bulb 12 V/10 W The halogen spotlights (Fig. 177,1) are in- stalled flush with the panel. Fig. 177 Halogen spotlight (variant 1) Changing bulbs: ³ Use a screw driver to remove the inner cov- er ring (Fig.

  • Page 169: Halogen Spotlights (Variant 2)

    Maintenance 12.8.3 Halogen Spotlights (Variant 2) Halogen bulb 12 V/10 W Halogen spotlights are available as individual lights and as combinations in various styles. Changing bulbs: ³ Remove the bulb holder from the bracket. ³ Remove halogen bulb. ³ Put in a new halogen bulb. ³...

  • Page 170: Spare Parts

    Maintenance 12.9 Spare Parts Every alteration of the original condition of the vehicle can jeopardize road safety. The special equipment and original spare parts recommended by Bürstner have been specially developed and supplied for your vehicle. Your Bürstner dealer carries these products.

  • Page 171: Vehicle Identification Plate

    Maintenance 12.10 Vehicle Identification Plate The vehicle identification plate (Fig. 182) with the chassis number is mounted on the right hand side on the front. Do not remove the vehicle identification plate. The vehicle identification plate: identifies the vehicle helps with the procurement of spare parts together with the vehicle documents identi- Fig.
  • Page 172 Maintenance T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 173: Wheels And Tyres

    Wheels and Tyres Chapter Overview Wheels and Tyres This chapter contains instructions about the tyres of the motorhome. The instructions address the following topics: tyre selection handling of tyres changing a wheel spare wheel support At the end of the chapter there is a table you can use to find the correct tyre pressure for your mo- torhome.

  • Page 174: Tyre Selection

    Wheels and Tyres ³ Check regularly that the wheel nuts or wheel bolts are firmly seated. Re-tighten the wheel nuts or wheel bolts of a changed wheel cross-wise after 50 km (30 miles) (Fig. 183). ³ When using new or newly painted rims, re- tighten the wheel nuts or wheel bolts once again after approx.

  • Page 175: Tyre Specifications

    Wheels and Tyres 13.3 Tyre Specifications 215/70 R 15C 109/107 Q Speed index (Q = 160 km/h) Load index code for twin tyres Load index code for single tyres Rim diameter in inches Tyre design (R = radial) Height-to-width proportion in percent Tyre width in mm 13.4 Handling of Tyres...

  • Page 176: Changing A Wheel

    Wheels and Tyres 13.5 Changing a Wheel 13.5.1 General Instructions The motorhome must be on level, firm ground, secure from slipping. Before jacking up the motorhome firmly apply the handbrake. Prevent the vehicle from rolling away with the wheel chocks. Under no circumstances jack the vehicle with the fitted steady legs.

  • Page 177: Tightening Torque

    Wheels and Tyres 13.5.2 Tightening Torque Type of Wheel rim Tightening vehicle torque Fiat Steel wheel rim 15" 160 Nm Steel wheel rim 16" 180 Nm Alloy wheel rim 130 Nm Mercedes- Steel wheel rim 180 Nm Benz Alloy wheel rim 180 Nm Renault Steel wheel rim...

  • Page 178: Spare Wheel Support

    Wheels and Tyres 13.5.4 Spare Wheel Support Due to its weight and fitted posi- tion, the spare wheel can be raised or lowered by a very strong person only (if working alone). Always get a second per- son to assist. Variant 1 and variant 2 The spare wheel can be found on the underside of the vehicle.

  • Page 179: Tyre Pressure

    Wheels and Tyres 13.6 Tyre Pressure Tyres overheat if the tyre pressure is too low. This can cause serious tyre damage. Approximately every two weeks and before long journeys, check the air pressure in all tyres, including the spare wheel. Only check the tyre pressure on cold tyres.
  • Page 180 Wheels and Tyres The information on pressure levels is valid for cold tyres and loaded vehicles. Chassis Types Tyre size Front air Rear air pressure pressure in bar in bar Fiat 11 All types 215/70 R 15 C (109/107) Q All types with tyres 215/70 R 15 C (109/107) Q "Michelin Camping"...

  • Page 181: Fault Search

    Fault Search Faults Chapter Overview Fault Search This chapter contains instructions about possible faults in the motorhome. The faults are listed with their possible causes and corresponding remedies. The instructions address the following topics: braking system electrical fittings gas fittings gas cooker gas oven microwave oven...

  • Page 182: Electrical Fittings

    Fault Search 14.2 Electrical Fittings A dryfill battery may only be replaced by a dryfill battery. Fault Cause Remedy Road light system does not Bulb is defective Unscrew cover of the relevant work fully light, replace bulb. Note volts and watts specifications Fuse on the transformer/recti- Replace fuse on the trans- fier is defective...
  • Page 183 Fault Search Fault Cause Remedy 12 V power supply does not 12 V power supply switched Switch 12 V power supply on work Battery cut-off switch or main Switch battery cut-off switch switch on the transformer/rec- or main switch on tifier is switched off Living area battery discharged Charge the living area battery...

  • Page 184: Gas Fittings

    Fault Search 14.3 Gas Fittings Fault Cause Remedy Gas odour, high rate of gas Leak in gas system Close regulator tap consumption on the gas bottle immediately. Open doors and win- dows and ventilate Do not smoke; do not ignite any open flames, and do not operate electric switches (starter,...

  • Page 185: Microwave Oven

    Fault Search 14.4.2 Microwave Oven Only qualified personnel may repair the microwave oven. Fault Cause Remedy Microwave appliance does not Fuse is defective Replace fuse cut in Door of the microwave oven is Remove foreign bodies stuck not properly closed in the door of the microwave oven and close door properly 14.5...
  • Page 186 Fault Search Fault Cause Remedy Boiler empties, safety/drain- Internal temperature below Heat inside age valve has opened 8 °C Battery cut-off switch or main Switch battery cut-off switch switch on the transformer/rec- or main switch on tifier is switched off Operating voltage below Charge or renew the living ar- 10.8 V...

  • Page 187: Alde Heater/Boiler

    Fault Search 14.5.2 Alde Heater/Boiler Fault Cause Remedy Red indicator lamp "Fault" is lit Air in the gas pipe system Switch off and on again. After two futile ignition attempts, wait for 10 minutes before try- ing again Lack of gas Open regulator tap and gas isolator tap Connect a full gas bottle...
  • Page 188 Fault Search Fault Cause Remedy In case of AES: Operating voltage of alternator Contact a specialist workshop Refrigerator does not switch is not present/too low to 12 V mode whilst in motion In case of AES: Lack of gas Open regulator tap and gas The refrigerator does not isolator tap switch on in gas operation,...

  • Page 189: Air Conditioning Unit

    Fault Search 14.6 Air Conditioning Unit 14.6.1 Dometic Fault Cause Remedy Air conditioning unit does not No 230 V power supply Connect 230 V power supply flash Temperature below 18 °C Temperature has been set in- Adjust the temperature correctly Thermostat defective Contact customer service Air conditioning unit does not...

  • Page 190: Water Supply

    Fault Search Fault Cause Remedy High water consumption Return pipe snapped off Re-align return pipe Pump in return system Replace pump defective No ventilation and no cooling Ventilator or controller defec- Contact customer service (LEDs light up) tive 14.7 Water Supply Fault Cause Remedy...

  • Page 191: Body

    Fault Search 14.8 Body Fault Cause Remedy Flap hinges/door hinges are Flap/door hinges are not suffi- Lubricate flap hinges/door difficult to operate ciently lubricated hinges with acid-free and res- in-free grease Hinges/joints in the bathroom Hinges/joints are not suffi- Lubricate hinges/joints with unit/toilet compartment are dif- ciently lubricated solvent-free and acid-free...
  • Page 192 Fault Search T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 193: Special Equipment

    Special Equipment Chapter Overview Special Equipment This chapter contains instructions about possible special equipment. The instructions address the following topics: bike rack motorcycle rack caravan coupling awning air conditioning unit satellite unit solar installation the gas alarm system At the end of the chapter there is a table listing the weights of special equipment. This chapter describes only selected special equipment.

  • Page 194: Bike Rack, Lowerable

    Special Equipment When loading the bike rack, observe the centre of gravity. The centre of gravity of the bicycles must be as close as possible to the rear wall of the motorhome. The bike rack should always be loaded from the inside to the outside. Loading the bike rack correctly: ³...

  • Page 195: Bike Rack, Not Lowerable

    Special Equipment 15.1.2 Bike Rack, Not Lowerable The bike rack (Fig. 191,2) permits the mo- torhome to easily transport 2 bicycles. Expan- sion for 3 bicycles is possible. Loading the bicycles: ³ Raise the telescopic swivel clip (Fig. 191,4). ³ Place the bicycles on top and secure them with quick straps (Fig.
  • Page 196 Special Equipment The motorcycle rack permits transport of a mo- torcycle or a motor scooter weighing up to 130 kg. Scope of delivery: Rack trough (Fig. 193,2) and retaining clip (Fig. 193,1) with quick closure (Fig. 192,1) Ramp (Fig. 194,2) Back-up lights and fog tail lights (Fig.

  • Page 197: Caravan Coupling

    Special Equipment 15.3 Caravan Coupling When mounting a caravan coupling, see the vehicle documents for information on maximum nose weight and caravan load. Retighten the caravan coupling fixing screws after 1000 operating hours. The caravan coupling and motorcycle rack may not be used simultaneously. An entry must be made in the vehicle documents in order to attach a caravan coupling.

  • Page 198: Air Conditioning Unit

    Special Equipment 15.5 Air Conditioning Unit 15.5.1 Dometic Operating modes: Automatic Ventilation, manual Cooling, manual Heating, manual The thermostat has a temperature range of 18 °C to 40 °C. Automatic mode: Fig. 197 Operating controls ³ Set the mains switch (Fig. 197,4) to "I". The 1 Button for manual adjustment of cooling fan speed set temperature is displayed.

  • Page 199: Oxycom

    Special Equipment 15.5.2 Oxycom Only operate the air conditioning unit over a longer period of time when the vehicle engine is run- ning or the vehicle is connected to the 230 V power supply. This pre- vents the battery from being dis- charged.
  • Page 200 Special Equipment Ventilation operation: ³ Press mains switch (Fig. 201,1). The air conditioning unit starts in the most recently selected function. The LED (Fig. 201,2) illu- minates. ³ Select ventilation level. To do this, press the ventilation button (Fig. 201,6) until the de- sired ventilation level has been reached (max.

  • Page 201: Satellite Unit

    Special Equipment 15.6 Satellite Unit 15.6.1 Equipment with Manual An- tenna Alignment Lower the mast before com- mencing your journey. This could be an accident hazard. Operation: ³ Switch on the TV set and receiver. ³ On the receiver, set a channel from the sat- ellite you want.

  • Page 202: Equipment With Automatic Antenna Alignment

    Special Equipment 15.6.2 Equipment with Automatic Antenna Alignment Before commencing the journey, make certain the antenna is in park position. The vehicle must be still during the satellite search. Do not walk through the vehicle. The satellite equipment is equipped with an automatic positioning unit. This automatic positioning unit ensures that the antennas are precisely aligned to the desired satellites.

  • Page 203: Solar Installation

    Special Equipment 15.8 Solar Installation Protect the solar collectors (solar module) against mechanical overload. The solar equipment supplies the most current under optimal sunlight conditions. Provide the solar collectors (solar module) open access to sunlight. Sunlight is greater in the open air than under trees and bridges. Tarpaulins block out sunlight.

  • Page 204: Gas Alarm System

    Special Equipment 15.9 Gas Alarm System The gas alarm system has two functions: Alarm in the case of an attack with narcotic Alarm if there is a leak in the gas fittings The gas alarm system is ready for operation as soon as the 12 V power supply is supplied with power.
  • Page 205 Special Equipment Item Surplus weight (kg) Waste water tank, heated with heating coils Airbag (driver and front passenger) Airbag (front passenger) Alloy wheel rims Stabiliser Antenna mast (hinged mast) Dashboard upgrade Automatic transmission External shower Roof rail and ladder Extractor hood Duomatic switching facility DVD player Single-section conversion door...
  • Page 206 Special Equipment Item Surplus weight (kg) Awning 3.5 m Awning 4.0 m Motorcycle rack Motorcycle rack in the rear garage Navigation system Fog light Pilot seats/swivel seat (passenger’s seat may be swiveled) 2 cross beams and slip protection for roof racks Blaupunkt radio/CD player completely installed Radio preparation including antenna and loudspeakers Reversing camera...

  • Page 207: Technical Data

    Technical Data 16.1 View of Ground Plans Technical Data Explanations: (1) Fuse 230 V (2) Transformer/rectifier with 12 V fuses (3) Living area battery with main fuse (4) Water pump mounted in the tank area (5) Drain cock for waste water tank (6) Electric safety/drainage valve (7) Boiler/heater C 3402/6002 (8) Water drain cock - yellow...

  • Page 208: Technical Data

    Technical Data Fig. 207 Ground plan T-585 Fig. 208 Ground plan T-602 Fig. 209 Ground plan T-605 T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...
  • Page 209 Technical Data Fig. 210 Ground plan T-610 Delfin Performance (Renault) Fig. 211 Ground plan T-615 Fig. 212 Ground plan T-625 Delfin Performance (Renault) T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...
  • Page 210 Technical Data Fig. 213 Ground plan T-680 (Mercedes-Benz)/T-680 Delfin (Renault) Fig. 214 Ground plan T-686 Delfin (Renault) Fig. 215 Ground plan T-695 Delfin (Renault) T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...
  • Page 211 Technical Data Fig. 216 Ground plan T-695 (Mercedes-Benz) Fig. 217 Ground plan T-700 Delfin Performance (Renault) Fig. 218 Ground plan T-710 (Mercedes-Benz) T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 212: Table Of Linear Measures

    Technical Data 16.2 Table of Linear Measures T-585 4740 4680 2290 2170 1390 5990 3700 1720 1720 2720 T-602 5210 5150 2290 2170 1860 6460 3700 1720 1720 2720 T-605 5210 5150 2290 2170 1860 6460 3700 1720 1720 2720 T-610 5440 5380 2300 2180 2033 6365...

  • Page 213: Power Supply

    Technical Data 16.3 Power Supply Mains connection Protection class I 230 V (+ 10/- 15 %), 47 - 63 Hz Mains power rating 400 VA Appropriate batteries 6-cell lead acid and lead acid gel batteries from 55 Ah Charging characteristics IUoU Final charge voltage 14.4 V...
  • Page 214 Technical Data T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 215: Helpful Notes

    Helpful Notes Chapter Overview Helpful Notes This chapter contains helpful tips on how to travel with the motorhome. The tips cover the following topics: traffic rules in foreign countries road assistance in European countries traffic laws in European countries gas supply in European countries toll regulations in European countries safe ways to spend the night during travel camping in winter...

  • Page 216: Help On Europe's Roads

    Helpful Notes 17.2 Help on Europe’s Roads  Emergency Breakdown Service Country Services  Police  100 TCB Brussels 0 70 34 47 77 Belgium  101  150 UAB (02) 9 80 33 08 Bulgaria  166  112 Falck 79 42 42 42 Denmark free of charge...
  • Page 217 Helpful Notes  Emergency Breakdown Service Country Services  Police  999 PZM 96 37 Poland  997  112 ACP Lissab. (21) 9 42 91 03 Portugal  112 ACP Porto (22) 8 34 00 01  961 ACR 92 71 Romania ...

  • Page 218: Speed Limits And Permissible Dimensions

    Helpful Notes 17.3 Speed Limits and Permissible Dimensions When travelling abroad, note and do not exceed the varying speed limits. For your information the speed limits and the permissible dimensions in some of the most visited countries: Date 04/2004 Country Max.
  • Page 219 Helpful Notes Country Max. dimensions Gross In built- Outside Motorway in meters weight up areas built-up areas Width Length Austria 2.55 up to 3.5 t over 3.5 t Poland 2.50 up to 3.5 t over 3.5 t Portugal 2.50 up to 3.5 t 90/100 over 3.5 t 80/90...

  • Page 220: Driving With Low Beam In European Countries

    Helpful Notes 17.4 Driving with Low Beam in European Countries The following is a list of the European countries in which driving with low beam is required even dur- ing the day. Country Conditions Denmark All year; on all roads Estonia All year;...
  • Page 221 Helpful Notes Country Sleeping on Sleeping on Comments roads and privately fields owned lands Italy Observe the local regulations. Parking and staying overnight on free areas is prohibited. Croatia Permission from the local authorities must be obatined in order to stay overnight on privately owned land.

  • Page 222: Gas Supply In European Countries

    Helpful Notes 17.6 Gas Supply in European Countries In Europe, there are several different connection systems for gas bottles. It is not al- ways possible to fill or exchange your gas bottles in a foreign country. Get information about the connection system in the country you are travelling to before embarking on your journey, e.g.

  • Page 223: Tips For Winter Campers

    Helpful Notes 17.9 Tips for Winter Campers The following tips will help make your winter camping experience as agreeable as possible. Reserve your parking place in good time. Good winter camping sites are often booked up early. Do not start your trip without winter tyres. Bring snow chains.
  • Page 224 Helpful Notes Bathroom/sanitary items Object Object Object Toilet brush Toothbrush glass Towels Toilet paper Sanitary items Living area Object Object Object Gas bottle Rain clothes Dustbin Green insurance card First aid kit List of addresses Insect lamp Travel guides/parking Registration confirma- guide tion(s) Insect repellent...
  • Page 225 Helpful Notes Outside Object Object Object Camping table Lock Stay rope Luggage racks String Bellows Tent pegs/tightening Camping chairs ropes T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...
  • Page 226 Helpful Notes T-Modell - 04/05 - Ausgabe 08/04 - 201804286 - BUE-0006-04EN...

  • Page 227: Inspection Plan

    Inspection Plan 18.1 Inspection Plan Inspection Plan Item Component Activity Intervall Auxiliary support Lubrication Annually Joints, hinges Lubrication Annually Refrigerator, heater, boiler, cooker, light- Function check Annually ing, flap and door closures, toilet, seat belts Windows, skylights Function check, water ingress Annually test Upholstery, curtains, blinds...
  • Page 228 Inspection Plan Delivery __________ Item 1-10 Stamp of the Bürstner dealer Date Signature 1st year ____________Item 1-10 2nd year __________ Item 1-13 Stamp of the Stamp of the Bürstner dealer Bürstner dealer Date Signature Date Signature 3rd year __________ Item 1-10 4th year __________ Item 1-13 Stamp of the Stamp of the...

  • Page 229: Index

    Index 19.1 Index Index Basic equipment ..... 19 12 V main switch ..... 95 Battery alarm .
  • Page 230 Index Rear lights ..... . 165 Circuit diagram External ......107 Side lights .
  • Page 231 Index Doors Boiler (Trumatic C) ....185 Conversion door ....39 Braking system .
  • Page 232 Index Fuse 230 V ......103 Heat exchanger, heater, replacement ..109 Position ......207 Heater Air outlet nozzles, adjustment .
  • Page 233 Index Insect screen, cleaning ....155 Notes ......85 Insect screen, hinged skylight Position .
  • Page 234 Index Hot-air heater....111 Refrigerator door locking mechanism Hot-water heater ....112 Closing .
  • Page 235 Index Seat belts......33 Symbols Cleaning ..... . . 156 For notes .
  • Page 236 Index Travel check lists ....223 Waste water tank heater ....141 Travelling with low beam .

This manual is also suitable for:

T-585T-602T-605T-610 delfin performanceT-615T-625 delfin performance ... Show all

Table of Contents

Save PDF