Burstner Lyseo Harmony Line TD 590 Instruction Manual
  1. Manuals
  2. Brands
  3. Burstner Manuals
  4. Motorhomes
  5. Lyseo Harmony Line TD 590
  6. Instruction manual

Burstner Lyseo Harmony Line TD 590 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction manual
Dear Reader ...
Instruction manual
We would like to congratulate you on the purchase of your new motorhome. You have selected a top-quality
vehicle which will afford you many years of enjoyment.
To enable you to always use and operate your motorhome properly and easily, your Bürstner dealer will first
provide you detailed instructions for all important functions when you take delivery.
This manual, the instruction manuals from the base vehicle manufacturer as well as the instruction manuals
from the appliance manufacturer will always be at hand to answer any questions you may have regarding your
motorhome.
Before your first journey
Please familiarise yourself with this manual rather than relying on it strictly for reference.
Fill in the warranty cards for the appliances and special equipment in the individual instructions and send these
cards to the respective manufacturers. This ensures your warranty claim for each appliance.
© 2017 Bürstner GmbH & Co. KG Kehl
T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Lyseo Harmony Line TD 590 and is the answer not in the manual?

Questions and answers

Roy Godsell
January 16, 2025

Where do I find the MCB switch that appears to have tripped out

0

Related Manuals for Burstner Lyseo Harmony Line TD 590

Summary of Contents for Burstner Lyseo Harmony Line TD 590

  • Page 1 Instruction manual Dear Reader ... Instruction manual We would like to congratulate you on the purchase of your new motorhome. You have selected a top-quality vehicle which will afford you many years of enjoyment. To enable you to always use and operate your motorhome properly and easily, your Bürstner dealer will first provide you detailed instructions for all important functions when you take delivery.
  • Page 2 Instruction manual T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...

  • Page 3: Table Of Contents

    Contents Introduction Pilot seats for the driver's and ....7 front passenger's seats ... . 42 General .
  • Page 4 Contents 6.4.2 Furniture flaps with handle 6.14.6 Pull-down bed, and push button ....64 electrically operated 6.4.3 Furniture flaps with handle (Ixeo Time, Lyseo TD) ... . .96 and unlocking bar.
  • Page 5 Contents 8.4.4 Charging batteries via Cooker ......166 a 230 V power supply ... . 125 9.5.1 Gas cooker .
  • Page 6 Contents Troubleshooting 11.4 Extractor hood ....205 ... . .229 11.5 Air conditioning unit ....205 14.1 Air suspension (Goldschmitt) .

  • Page 7: Introduction

    Introduction Please read this instruction manual completely before 1Introduction using the vehicle for the first time! Always keep this instruction manual in the vehicle. Also inform all other users of the safety regulations. The non-observance of this symbol can lead to personal injury. The non-observance of this symbol can lead to damage being caused to, or inside the vehicle.

  • Page 8: General

    Introduction General The vehicle is constructed in accordance with the latest technology and the recognised safety regulations. Nevertheless, personal injury may result and the vehicle may be damaged if the safety instructions in this instruction manual are not followed. Before using the vehicle for the first time, equip it with the legally prescribed equipment (e.g.
  • Page 9 Introduction Use an environmentally-friendly WC chemical agent for the WC which can also be biologically degraded and only use small doses. When staying in towns and communities for long periods, search for parking areas which are specially reserved for motorhomes. Enquire at the town or community authority about parking spaces.
  • Page 10 Introduction T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...

  • Page 11: Safety

    Safety Chapter overview 2Safety This chapter contains important safety instructions. The safety instructions are for the protection of persons and property. Fire prevention 2.1.1 Avoidance of fire risks Never leave children in the vehicle unattended. Keep flammable materials clear of heating and cooking appliances. Halogen lamps can get very hot.

  • Page 12: General

    Safety General The oxygen in the vehicle interior is used up by breathing and the use of gas operated appliances. That is why the used air must be replaced per- manently. For this purpose, forced ventilation systems (e.g. skylights with forced ventilation, mushroom-shaped vents or floor vents) are installed in the vehicle.
  • Page 13 Safety Before commencing the journey, open, lock and secure the shades sit- uated on the windscreen and on the driver's and front passenger's win- dows. Before commencing the journey, rotate all swivel seats in the direction of travel and lock in position. During the journey, the swivel seats must remain locked in place in the direction of travel.

  • Page 14: Towing

    Safety Before commencing the journey, close all external flaps and lock them. Before commencing the journey, remove the external supports and retract the corner steadies or steady legs, which are fitted to the vehicle. Before commencing the journey, put the antenna in park position. During the initial journey and each time after changing a wheel, re-tighten the wheel bolts/wheel nuts after 50 km (30 miles).

  • Page 15: Gas Bottles

    Safety If the gas system is defective: Do not smoke; do not ignite any open flames, and do not operate electric switches (light switches etc.). Check the tightness of gas-conducting parts and lines with leakage search spray. Do not check with an open flame. Only the stipulated devices may be connected to internal connections.

  • Page 16: Electrical System

    Safety Connect the gas tube to the gas bottle without tension. If the gas bottles are not connected to the gas tube, always place the protective cap on top. Close the regulator tap on the gas bottle before the gas pressure regu- lator or gas tube are removed from the gas bottle.

  • Page 17: Before The Journey

    Before the journey Chapter overview 3Before the journey This chapter contains important information which has to be noted before com- mencing your journey or carrying out any tasks before the journey. At the end of the chapter there is a checklist which once again summarises the most important points.

  • Page 18: Terms

    Before the journey Description Load (kg) Maximum permitted Pull-down bed payloads Roof load Rear garage and rear storage space Pull-out in the rear storage space Bike rack, not lowerable Double/triple Bike rack, lowerable Double/triple Load rack (SAWIKO) 3.3.1 Terms Technically speaking, the term "mass" has now replaced the term "weight". However, "weight"...
  • Page 19 Before the journey Example for calculating Water tank in the ready-to-drive state with 20 l (overflow open) 20 kg the basic equipment Aluminium gas bottle + 11.5 kg Boiler with 20 l + 20 kg 230 V power cable + 4 kg Total = 55.5 kg The mass in ready-to-drive condition and the actual weight are shown in the...

  • Page 20: Calculating The Payload

    Before the journey No matter where kept, personal equipment also includes: Animals Bikes Boats Surfboards Sports equipment For the personal equipment, according to the applicable regulations, the man- ufacturer must use a minimum weight that is determined according to the fol- lowing formula: Formula Minimum weight M (kg) = 10 x N + 10 x L...

  • Page 21: Loading The Vehicle Correctly

    Before the journey The individual values give the current axle loads. These are important for the correct loading of the vehicle (see section 3.3.3). The sum of these values is the current weight of the vehicle. The actual payload is the difference between the maximum permissible gross weight in laden condition and the weighed vehicle weight.

  • Page 22: Rear Garage/Rear Storage Space

    Before the journey Measure the external distances horizontally from the centre of the front wheel to the centre of the storage space or to the centre of the back wheel. Calculating axle loads: Multiply the distance between storage space and front axle (A) with the weight of the load in the storage space (G) and divide the result by the wheelbase (R).

  • Page 23: Bike Rack (Special Equipment)

    Before the journey Depending on the vehicle equipment, clamping rails with clamping eyelets are mounted in the rear garage or in the rear storage space. Always secure loads onto the clamping eyelets. Always use tightening straps or lashing nets for securing the load, never rubber expanders. When clamping loads, always check that the clamping eyelets are placed tightly in the clamping rails.
  • Page 24 Before the journey Loading the bike rack with When loading the bike rack, observe the centre of gravity. The centre of gravity bicycles of the bicycles must be as close as possible to the rear wall of the vehicle. The bike rack should always be loaded from the inside to the outside.

  • Page 25: Load Rack Sawiko (Special Equipment)

    Before the journey Bike rack, lowerable Also read the manufacturer's instruction manual. Fig. 2 Bike rack, folded upwards Fig. 3 Bike rack, lowered The bike rack (Fig. 2) permits to easily transport 2 bicycles. Expansion for 3 bicycles is possible. A winding system can be used to lift and lower the bike rack.

  • Page 26: Towing

    Before the journey The load rack permits transport of a load weighing up to 130 kg. For the trans- port of the load different attachments are available. They are e.g. bike rack or a transport box. Our authorised dealers and service centres will be happy to advise you.

  • Page 27: Caravan Coupling (Special Equipment)

    Before the journey Depending on the model, different nose weights may apply for the caravan couplings. Refer to the following table for the respective permissible nose weight. Model Permissible nose weight SAWIKO MT019 75 kg SAWIKO (other) 100 kg Linnepe 100 kg AL-KO 80 kg...

  • Page 28: Electrically Operated Entrance Step (Partially Special Equipment)

    Before the journey Electrically operated entrance step (partially special equipment) Before commencing the journey and after short interruptions of the journey, ensure that the entrance step is completely retracted. Do not stand in the direct range of the entrance step while it is being retracted or extended.

  • Page 29: Tv Unit (Special Equipment)

    Before the journey Retracting: Press the rocker button (Fig. 10,1) up until the entrance step has retracted completely. Fig. 11 Indicator lamp When the ignition is switched on and the entrance step is extended, an indi- cator lamp (Fig. 11,1) is illuminated on the dashboard. TV unit (special equipment) Before commencing the journey, place and secure the flat screen and screen support in the initial position.

  • Page 30: Securing Add-On Parts

    Before the journey Securing add-on parts In the event of an accident or emergency braking, loose add-on parts could injure the occupants of the vehicle. Before setting off, secure loose add-on parts in the holders provided or stow them in a secure place inside the vehicle.

  • Page 31: Gas Regulator

    Before the journey Coffee table of the rear A movable coffee table is installed in the seat box of the rear seating group. seating group Fig. 17 Bench and coffee table Fig. 18 Coffee table lock Securing the coffee table: Lower the coffee table.

  • Page 32: Snow Chains (Special Equipment)

    Before the journey Fig. 19 Gas regulator with CPU and hose break guard Gas tube Crash protection unit (CPU) Knob for manual switching of the gas bottles Gas pressure regulator with reversing valve and indicator Hose break guard Regulator tap on the gas bottle Gas regulator with CPU If a gas regulator with crash protection unit (Fig.

  • Page 33: Road Safety

    Before the journey 3.12 Road safety Check tyre pressure before a journey or every 2 weeks. Wrong tyre pressure causes excessive wear and can lead to damage or even to tyre burst. You can lose control of the vehicle (see section 13.7). Before commencing the journey, work through the checklist: Checks Checked...
  • Page 34 Before the journey Checks Checked All doors secured Pull-down bed secured in top end position Children's seats mounted to seats with three-point safety belts Swivel seat locking device for driver's seat and front passen- ger's seat locked Shades in the driver's cabin opened and secured Gas system Gas bottles firmly fixed in the gas bottle compartment so that they are unable to turn...

  • Page 35: During The Journey

    During the journey Chapter overview 4During the journey This chapter contains instructions on how to drive the motorhome. Driving the motorhome The base vehicle is a commercial vehicle (small truck). Adjust your driving technique accordingly. Before commencing the journey and after short interruptions of the journey, ensure that the entrance step is completely retracted.

  • Page 36: Reversing Camera (Special Equipment)

    During the journey Reversing camera (special equipment) Fig. 20 Reversing camera with infrared illumination A reversing camera (Fig. 20) is installed in the vehicle. When it is dark, the infrared LEDs of the reversing camera illuminate the field of view. The image of the reversing camera is fed into the central multimedia/naviga- tion system and shown on the existent LCD monitor.

  • Page 37: Brakes

    During the journey Brakes Have defects on the braking system immediately remedied by an author- ised specialist workshop. Before each journey Before each journey, check by means of a braking test: Do the brakes function? Do the brakes react evenly? Does the vehicle remain in the lane when braking? Air suspension Goldschmitt (special equipment) Make sure that no persons are staying underneath the vehicle or...

  • Page 38: Seat Belts

    During the journey Seat belts 4.6.1 General The vehicle is equipped with seat belts in the living area on the seats for which seat belts are compulsory by law. National regulations apply seat-belt fas- tening. Fasten your seat belts before the beginning of the journey and keep them fastened during the journey.

  • Page 39: Child Restraint Systems

    During the journey Child restraint systems When travelling, secure children under 13 years of age that are smaller than 150 cm, with a suitable and officially approved child restraint system. Only attach the child restraint system to seats that are specified for this purpose.
  • Page 40 During the journey Fig. 23 Child seats on bench Fig. 24 Child seat on L-shaped bench The arrow in Fig. 23 and Fig. 24 shows the direction of travel. On the L-shaped bench, the back cushion on the side wall must be removed when a child seat is fitted.

  • Page 41: Isofix Child Safety Seat Mounting System (Special Equipment)

    During the journey ISOFIX child safety seat mounting system (special equipment) Fig. 25 ISOFIX child safety seat mounting system If the vehicle is equipped with the ISOFIX child safety seat mounting system, the vehicle seats suitable for it are marked with the ISOFIX symbol. These vehicle seats have retaining brackets (Fig.

  • Page 42: Pilot Seats For The Driver's And Front Passenger's Seats

    During the journey Pilot seats for the driver's and front passenger's seats Before commencing the journey, rotate all swivel seats in the direction of travel and lock in position. The seats must remain fixed in position during the journey and are not to be rotated.

  • Page 43: Headrests

    During the journey 4.11 Headrests Fig. 27 Bench headrest, one-part Fig. 28 Bench headrest, two-part Before commencing the journey, adjust the headrest (Fig. 27,1 or Fig. 28,1) so that the back of the head is supported at approximately ear height. Push the headrests upwards or downwards by hand.

  • Page 44: Roman Shade In The Driver's Cabin

    During the journey 4.13 Roman shade in the driver's cabin 4.13.1 Pleated Roman shades When on the move, the Roman shades for the windscreen, driver's window and the front passenger's window respectively must be com- pletely removed. Fig. 30 Pleated Roman shades Removing the pleated Open the snap fasteners (Fig.

  • Page 45: Roman Shades, Remis (Partially Special Equipment)

    During the journey 4.13.2 Roman shades, Remis (partially special equipment) While travelling, the Roman shades for the windscreen, driver's window and front passenger's window must be open, in a fixed position and secured. Fig. 31 Roman shade for the wind- Fig.

  • Page 46: Topping Up Adblue ® (Citroen Base Vehicle)

    During the journey ® 4.15 Topping up AdBlue (Citroen base vehicle) ® ® Store AdBlue out of the reach of children. Do not store any AdBlue containers in the vehicle. ® If the AdBlue tank is empty, you cannot start the vehicle. If you have ®...

  • Page 47: Pitching The Motorhome

    Pitching the motorhome Chapter overview 5Pitching the motorhome This chapter contains instructions on how to pitch the vehicle. Pitch the vehicle so that it is as horizontal as possible. Use ramps where necessary. Otherwise, the water from the shower tray will not be able to drain properly.

  • Page 48: Supports

    Pitching the motorhome Supports 5.5.1 General instructions The steady legs must not be used to jack up the vehicle in order to work beneath it, e.g. to change a wheel or carry out maintenance work. Whilst the vehicle is in a jacked up position, persons must not lie down under it.

  • Page 49: Steady Legs (Al-Ko) (Special Equipment)

    Pitching the motorhome Retracting: Place the socket spanner on the hexagon nut (Fig. 34,1) and rotate until the steady leg is clear of the ground. If the length of the steady leg can be adjusted, remove the splint (Fig. 34,4) out of the support foot extension (Fig.

  • Page 50: Connection

    Pitching the motorhome 230 V connection The vehicle can be connected to a 230 V power supply (see chapter 8). Refrigerator If the refrigerator is set to 12 V operation, it will constantly consume cur- rent. Therefore, switch over to gas operation when the vehicle engine is not running, and the vehicle is not connected to the 230 V power supply.
  • Page 51 Pitching the motorhome 1 LED indicator of the selected satellite 2 On/Off button 3 Display 4 SAT button Fig. 36 Operating panel (TeleSat) Switching on the unit: Press the On/Off button (Fig. 36,2). The LED indicator of the selected sat- ellite (Fig.

  • Page 52: Satellite Unit With Automatic Antenna Alignment (Teleco)

    Pitching the motorhome 5.8.2 Satellite unit with automatic antenna alignment (Teleco) The satellite unit is equipped with an automatic advance unit. This automatic advance unit ensures that the antenna is aligned precisely. When switching on the unit, the antenna is extended automatically. When switching off the unit or when starting the vehicle engine, the antenna is retracted automatically.

  • Page 53: Satellite Unit With Automatic Antenna Alignment (Oyster Premium)

    Pitching the motorhome Switching off the unit: Press the AUTO button (Fig. 37,2 or Fig. 38,2). The antenna automatically moves into parking position. When reaching the parking position, this is displayed on the screen. The television and advance unit switch off after a few seconds. Operating the unit without Press the Television on/off button (Fig.
  • Page 54 Pitching the motorhome 1 Operating buttons on the back of the device 2 Standby mode/operation LED 3 ON/OFF flip switch Fig. 39 Operation on the flat screen POWER button Manual control of antenna EXIT button - exit menu without saving Programme selection button OK button - confirm selection or save setting...

  • Page 55: Awning (Special Equipment)

    Pitching the motorhome Operating the unit without Press the PARK button (Fig. 40,2). The antenna moves into parking posi- using the antenna: tion. Press the SOURCE button (Fig. 40,6) repeatedly until the desired signal source (e.g. DVD) has been selected. Switching off the unit: Press the POWER button (Fig.
  • Page 56 Pitching the motorhome T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...

  • Page 57: Living

    Living Chapter overview 6Living This chapter contains instructions about living in the vehicle. Central locking system (special equipment) The central locking mechanism locks the driver's door, the passenger's door and the conversion entrance door. The central locking system has no function, if the battery cut-off switch on the transformer/rectifier is switched off.

  • Page 58: Conversion Door

    Living Conversion door Only drive with locked doors. Locking the doors can prevent them from opening of their own accord, e.g. during an accident. Locked doors also prevent forced entry, e.g. when waiting at traffic lights. However, in an emergency, locked doors make it more difficult for helpers to enter the vehicle.

  • Page 59: Conversion Door, Outside

    Living 6.2.2 Conversion door, outside Fig. 45 Door lock of conversion door, outside Opening: Insert the key into locking cylinder (Fig. 45,1) and turn until the door lock is unlatched. Return the key to the central position and remove it. Pull upper part of the door handle (Fig.

  • Page 60: Window Of Conversion Door (Partially Special Equipment)

    Living 6.2.4 Window of conversion door (partially special equipment) The conversion door window is fitted with a Roman shade. Fig. 47 Roman shade Closing: Grip the Roman shade (Fig. 47,2) in the middle of the holding bar (Fig. 47,1), pull it upwards and then release it at the desired height. The Roman shade will stay at this height.

  • Page 61: External Flaps

    Living External flaps Before commencing the journey, close all external flaps and lock them. To open and close the external flap, open or close all locks that are fitted to the external flap. When leaving the vehicle, close all external flaps. The external flaps fitted to the vehicle are all fitted with identical locking cylin- ders.

  • Page 62: Garage Flap Emergency Release

    Living 6.3.2 Garage flap emergency release The garage flap can be opened from the interior using the emergency release. The emergency release is even possible if the garage flap has been locked with the key. Fig. 50 Garage flap emergency release Unlocking the garage flap: Pull both handles of the emergency release (Fig.

  • Page 63: Service Unit Flap Lock

    Living 6.3.4 Service unit flap lock Fig. 53 Flap lock, locked Fig. 54 Flap lock, open Opening: Insert the key into the locking cylinder and turn until the red ring (Fig. 54,1) is visible. The flap lock is unlatched. Remove the key. Turn the handle half a turn in an anticlockwise direction until the red area (Fig.

  • Page 64: Furniture Flaps With Handle And Push Button

    Living Closing: Press furniture flap shut. Press push button in until it locks. The furniture flap is closed correctly when the fastener locks into place. 6.4.2 Furniture flaps with handle and push button Fig. 57 Furniture flap with handle Fig. 58 Furniture flap with handle (example) (alternative)

  • Page 65: Furniture Flaps With Release Handle

    Living 6.4.4 Furniture flaps with release handle Fig. 60 Furniture flap with release handle Opening: Pull the release handle (Fig. 60,1) outwards. Pull the release handle until the furniture flap is open. Closing: Press the furniture flap down until you can feel the flap hinge close and hear the lock snap into place.

  • Page 66: Rotating Seats

    Living Rotating seats Before commencing the journey, rotate all swivel seats in the direction of travel and lock in position. During the journey, the swivel seats must remain locked in place in the direction of travel. Push the driver's seat into the central position before rotating it. If the driver's seat is in the very back or in the very front, there is a risk of colliding with the handbrake lever or the seating group when rotating the driver's seat.

  • Page 67: Interior

    Living 6.7.2 Interior The lamps shown in this section are examples. Not all lamps used in the vehicle are shown. The examples are intended to clarify the possible posi- tions for the light switches. The type and appearance of the light switches can deviate from those shown here.

  • Page 68: Wardrobe Light (Partially Special Equipment)

    Living 6.7.3 Wardrobe light (partially special equipment) The wardrobe light can be removed from its holder (Fig. 70,1) and used as a torch. When the wardrobe door is closed, the wardrobe light switches off auto- matically. A brightness sensor ensures that the wardrobe light comes on only when it is dark.

  • Page 69: Spotlight

    Living Spotlight Bulbs and light fittings can be extremely hot. Allow the light bulbs and lamp holders to cool down before touching them. If the light is switched on or still hot, there must always be a safety dis- tance of at least 30 cm between stores or curtains and flammable objects.

  • Page 70: Holder For Flat Screen

    Living Holder for flat screen Before commencing the journey, place and secure the flat screen and screen support in the initial position. If the screen holder is installed in a TV cabinet: Close TV cabinet. 6.9.1 Holder on the column The holder for the flat screen is attached to a column.

  • Page 71: Wall Holder

    Living 6.9.3 Wall holder The flat screen is fastened to a wall holder. Fig. 76 Wall holder Positioning: Pull down the release lever (Fig. 76,1) and turn the holder (Fig. 76,2) with the flat screen to the desired position. Storing away: Pull down the release lever and push back the flat screen until the holder engages.

  • Page 72: Holder, Rotatable

    Living 6.9.5 Holder, rotatable The flat screen is fastened to a holder with a rotatable joint. Fig. 78 Holder (rotatable) Positioning: Swivel the flat screen into the desired position. Removing flat screen: Press and hold latch (Fig. 78,1) to the right. Remove flat screen upwards.

  • Page 73: Windows

    Living 6.11 Windows The windows are fitted with a blind or Roman shade and with an insect screen or folding insect screen. After the latch has been released, the blind and insect screen automatically spring back to the initial position by tensile force.

  • Page 74: Hinged Window

    Living 6.11.1 Hinged window If windows with automatic hinges are fitted, open the window fully in order to release the lock. If the locking device is not released and the window is closed nevertheless, there is the danger of the window breaking due to the massive counter-pressure.
  • Page 75 Living Closing: Hinged window with rotary hinge: Turn knurled knob (Fig. 81,1) until the latch is released. Hinged window with automatic hinge: Open the hinged window as wide as is necessary to release the lock. Close the hinged window. Press and hold the security button (Fig. 79,1), if present. Turn the catch lever (Fig.

  • Page 76: Sliding Window With Pressure Lock

    Living 6.11.2 Sliding window with pressure lock Fig. 85 Sliding window, locked Fig. 86 Sliding window, unlocked Opening: Push the latch (Fig. 85,1) downwards. Open the window to the desired position. Closing: Close the window as far as it can go. Push the latch (Fig.

  • Page 77: Roman Shade And Insect Screen

    Living Opening: If the blind is completely closed: Press handle (Fig. 87,2) downwards and, at the same time, tilt it slightly inward. The blind can be taken out of the locking devices situated on both sides of the window frame. If the blind is in an intermediate position: Pull the handle (Fig.

  • Page 78: Roman Shades For Windscreen, Driver's Window And Front Passenger's Window

    Living 6.11.5 Roman shades for windscreen, driver's window and front passenger's window Depending on the model, the driver's cabin is shaded either with pleated shades or with Remis Roman shades (special equipment). Pleated shades The pleated shades are standard equipment on the vehicle. Fig.

  • Page 79: Skylights

    Living Driver's window and front passenger's window Fig. 92 Roman shade for driver's and passenger's window Shading: Press the release handles (Fig. 92,1) and hold them down. Using the handle (Fig. 92,2), draw the Roman shades for the driver's and passenger's window to the other side of the window and secure them to the magnetic strips.

  • Page 80: Skylight With Snap Latch

    Living Before commencing the journey, close the skylights. Before commencing the journey, check that the skylights are closed and locked. When leaving the vehicle, always close the skylights. 6.12.1 Skylight with snap latch Fig. 93 Skylight with snap latch Fig. 94 Handles with snap latches The skylight can be pushed upwards either from one side or from both sides.

  • Page 81: Heki Skylight (Mini And Midi) (Partially Special Equipment)

    Living Opening: Use handle (Fig. 93,1) to swing down the insect screen (Fig. 93,2). Release the retainer (Fig. 95,3) from the hook (Fig. 95,4) and, using the handle (Fig. 95,1), slowly return the blind (Fig. 95,2). Swing insect screen upwards until it latches in place. 6.12.2 Heki skylight (mini and midi) (partially special equipment) Fig.

  • Page 82: Omni-Vent Skylight With Fan (Special Equipment)

    Living Pull the bar in the guides (Fig. 97,2) to the desired position. Push the bar slightly upwards and into the selected guide (Fig. 98,1 or 2) and lock if necessary. Roman shade To close and open the Roman shade: Closing: Pull out Roman shade at the handle and release in the required position.
  • Page 83 Living Insect screen To close and open the insect screen: Closing: Using the handle (Fig. 100,4) pull the insect screen across to the other side of the frame. Opening: Press the handle of the insect screen together. The latch is released. Use handle to return the insect screen slowly to its initial position.

  • Page 84: Skyroof Skylight (Partially Special Equipment)

    Living 6.12.4 Skyroof skylight (partially special equipment) When opening the skylight, ensure that there are no torsional forces. Open and close the skylight evenly. If the catch lever is equipped with a safety knob, press the safety knob when operating the catch lever. Fig.
  • Page 85 Living Fig. 105 Catch lever with safety knob in Fig. 106 Catch lever in "continuous ven- "continuous ventilation" posi- tilation" position tion Continuous ventilation With the catch levers, the skylight can be placed in 2 different positions: "Continuous ventilation" (Fig. 105 and Fig. 106) "Firmly closed"...

  • Page 86: Tables

    Living Fig. 107 Skyroof skylight Roman shade The Roman shade is fitted in the frame, at the bottom. Closing: Hold the Roman shade in the centre of the bottom rod and carefully draw it upwards. Release the Roman shade at the desired position. The Roman shade will stay in that position.

  • Page 87: Fixed Table

    Living Depending on the model, the tables can be adjusted in one or more of the aforementioned ways. The tables' main operation is described below. The type and position of the operating controls may vary slightly. 6.13.1 Fixed table Table leg The table leg is screwed into the floor.

  • Page 88: Suspension Table

    Living 6.13.2 Suspension table Table leg The table leg can be set up at two different heights: Normal table height Decreased table height (when converting to a bed foundation) To lower the table, there are the following possibilities (depending on model): Replacing the long table leg with a short one Folding in one part of the table leg Removing one part of the table leg...

  • Page 89: Lift-Off Table

    Living 6.13.3 Lift-off table Table leg The table leg is screwed into the floor. The table can be lowered via a lifting mechanism to become a bed foundation. Adjusting the table top Depending on the model, the table top can be moved both lengthwise and crosswise.

  • Page 90: Lift-Off Table (Variant)

    Living 6.13.4 Lift-off table (variant) Table leg The table leg is screwed into the floor. The table can be lowered via a lifting mechanism to become a bed foundation. Adjusting the table top Depending on the model, the table top can be rotated and shifted both length- wise and crosswise.

  • Page 91: Coffee Table (Dependent On Model)

    Living 6.13.5 Coffee table (dependent on model) The coffee table can be lowered. The coffee table can be stored in the seat box. Fig. 114 Coffee table, stored Fig. 115 Coffee table, extended Extending the coffee table: Press the push buttons (Fig. 114,1) on the seat box panel. The push but- tons jump out.

  • Page 92: Fixed Bed

    Living 6.14.2 Fixed bed (adjustable head section) Do not let the slatted frame fall down when closing the bed! Fig. 117 Adjustable head section Depending on the configuration, the head section of the slatted frame can be adjusted in several stages. Raising the head section: Raise the head section (Fig.

  • Page 93: Fixed Bed, Height Adjustable Via Strap System (Special Equipment)

    Living Fig. 118 Crank in the rear garage Attach the crank (Fig. 118,2) onto the journal (Fig. 118,1). To lift the bed: Turn the crank clockwise. To lower the bed: Turn the crank anticlockwise. Remove the crank and store it. 6.14.4 Fixed bed, height adjustable via strap system (special equipment)

  • Page 94: Pull-Down Bed

    Living 6.14.5 Pull-down bed, electrically operated (Ixeo TL) The maximum permitted pull-down bed load is 200 kg. Do not reach into the area between the bed and the side wall when low- ering or raising. Danger of bruises! Do not lower or lift the bed when there are people using the pull-down bed.
  • Page 95 Living Lowering the pull-down bed: Removing any obstacles in the area into which the pull-down bed extends: Push the seats forwards and rotate, lower backrests, remove or fold cush- ions if necessary. Switch off the lamps underneath the pull-down bed. Turn the key in the key switch (Fig.

  • Page 96: Pull-Down Bed, Electrically Operated (Ixeo Time, Lyseo Td)

    Living Inserting the safety plates: Bring out the safety plates under the mattress and place them on the pull- down bed. Climb into the pull-down bed via the access ladder. Insert the safety plates (Fig. 122,1) between the mattress and the bed sur- round (Fig.
  • Page 97 Living Only lower the bed if the lowering area is clear. Only lower the pull-down bed so far that it does not lie on any obstacles such as headrests, cushions or anything similar. If possible, remove such obstacles before lowering. Do not allow children to play with the pull-down bed.
  • Page 98 Living Fig. 125 Pull-down bed complete with Fig. 126 Pull-down bed, completely low- applied safety net ered (dependent on model) Safety net The three safety nets (Fig. 125,2) with their retaining belts are located under- neath the mattress in the pull-down bed. Only use the safety nets if persons are already in the pull-down bed.

  • Page 99: Pull-Down Bed At The Rear, Electrically Operated (Lyseo Td) (Special Equipment)

    Living Fig. 129 Access to drive (Lyseo) Fig. 130 Mechanical operation, drive If the holder (Fig. 129,1) for the drive is installed in the wall-mounted cup- board: open the wall-mounted cupboard. Remove mattress from pull-down bed and reduce the load of the storage cupboards to a minimum.
  • Page 100 Living Fig. 131 Control unit Control unit The pull-down bed is raised or lowered using the buttons (Fig. 131,1 and 4) on the control unit (Fig. 131,3). The control unit is protected against unauthorized use with the key switch (Fig. 131,2). Fig.

  • Page 101: Converting Seating Groups For Sleeping

    Living Emergency operation If it is no longer possible to move the pull-down bed with the arrow keys (Fig. 131,1 and 4), first of all check the fuse in the rear wall-mounted cupboard (Fig. 134,1). If the fuse is okay and it is still not possible to move the pull-down bed, the pull-down bed can be operated manually.
  • Page 102 Living Model Seating group Table type Section Ixeo Time Edition 30 IT 590 L-seating group with Lift-off table Transverse 6.15.4 lateral bench IT 710 Individual bench with Suspension table Transverse 6.15.2 dinette lateral seat with rotating plat- form IT 710 L-seating group with Lift-off table Transverse...

  • Page 103: Conversion Of Semi-Dinette Into Guest Bed

    Living Model Seating group Table type Section L-seating group with Lift-off table Transverse 6.15.3 L-SG lateral seat Individual bench with Suspension table Transverse 6.15.2 dinette lateral seat L-seating group with Lift-off table Transverse 6.15.3 L-SG lateral seat Individual bench with Suspension table Transverse 6.15.7...

  • Page 104: Conversion Semi-Dinette Into Transverse Bed (With Additional Cushion Table)

    Living 6.15.2 Conversion semi-dinette into transverse bed (with additional cushion table) Fig. 138 Prior to conversion Fig. 139 After conversion Convert the suspension table into a bed foundation (see section 6.13). Remove the back cushion of the bench and lay it aside. Push the cover of the lateral seat/lateral bench towards the centre of the vehicle as far as it will go.

  • Page 105: Conversion L-Seating Group Into Transverse Bed (Without Additional Cushion Table)

    Living Place the rectangular additional cushion on the table (between the seat cushions of the benches, see Fig. 141). Fully unfold the support underneath the additional cushion with reinforce- ment plate. Hook the hooks on the additional cushion with reinforcement plate into the holders on the bench seat and place the support on the floor.

  • Page 106: Conversion L-Seating Group Into Transverse Bed (Ixeo It 734)

    Living Fully unfold the support underneath the additional cushion with reinforce- ment plate. Hook the hooks on the additional cushion with reinforcement plate into the holders on the bench seat and place the support on the floor. 6.15.6 Conversion L-seating group into transverse bed (Ixeo IT 734) Fig.

  • Page 107: Conversion L-Seating Group Into Transverse Bed (Ixeo It 640)

    Living Fully unfold the support underneath the additional cushion with reinforce- ment plate. Hook the hooks on the additional cushion with reinforcement plate into the holders on the bench and place the support on the floor. 6.15.8 Conversion L-seating group into transverse bed (Ixeo IT 640) Fig.

  • Page 108: Shower Connection Point For External Shower (Special Equipment)

    Living 6.16 Shower connection point for external shower (special equipment) Only use the external shower if there is a gap of at least 1.20 m between the shower and the nearest electrical device or connection. Risk of elec- tric shock! If decommissioned for a longer time or if there is a risk of frost, drain the water system.

  • Page 109: Gas System

    Gas system Chapter overview 7Gas system This chapter contains instructions regarding the gas system of the vehicle. The operation of the gas operation appliances of the vehicle is described in chapter 9. General The operator of the gas system is responsible for the performance of recurring inspections and for complying with the maintenance intervals.
  • Page 110 Gas system If there are several gas devices, each gas device must have its own gas isolator tap. If individual gas devices are not in use, close the respective gas isolator tap. Ignition safety valves must close within 1 minute after the gas flame has extinguished.

  • Page 111: Gas Bottles

    Gas system Gas bottles Handle full or emptied gas bottles outside the vehicle only with closed regulator tap and attached protective cap. Gas bottles are only to be transported within the designated gas bottle compartment. Place the gas bottles in vertical position in the gas bottle compartment. Fasten the gas bottles so that they are unable to turn or tilt.

  • Page 112: Gas Isolator Taps

    Gas system Gas isolator taps 1 Cooker 2 Hot water 3 Refrigerator 4 Oven/grill 5 Heater 6 Hot water/heater HYW09219 Fig. 155 Possible symbols for the gas isolator taps A gas isolator tap (Fig. 155) for every gas device is built into the vehicle. The gas isolator taps are located in the vehicle at different positions, and can also be fitted separately.

  • Page 113: External Gas Connection (Special Equipment)

    Gas system External gas connection (special equipment) If the external gas connection is not in use, always close the gas isolator tap. Only gas appliances with a suitable adapter should be connected to the external gas connection. Connect only external gas appliances which are designed for an opera- tion pressure of 30 mbar.

  • Page 114: Gas Bottle Switching Facility (Special Equipment)

    Gas system Gas bottle switching facility (special equipment) If the vehicle is equipped with a gas bottle switching facility without Crash Protection Unit (CPU), it is not permitted to operate gas devices during the journey. Close the regulator taps on the gas bottles and the gas isolator taps before setting off.
  • Page 115 Gas system Facility with Crash The gas bottle switching facility consists of a combined gas pressure regulator Protection Unit (CPU) with reversing valve and indicator (Fig. 159,4), and an electrovalve (Fig. 159,2). The electrovalve blocks the gas supply to the vehicle in the event of a full braking, an accident, or an unusually great inclined position.
  • Page 116 Gas system Without remote display The indicator lamp on the operating unit shows the condition of the gas system. The system is okay when the indicator lamp (Fig. 160,1) lights up green. When the indicator lamp lights up or flashes red a fault has occurred. The gas supply is interrupted.

  • Page 117: Changing Gas Bottles

    Gas system Fix gas bottle in place with the fixing belts. Remove the protective cap from the gas bottle. Connect the full gas bottle to the gas tube. Open the regulator tap on the gas bottle. Press the hose break guard for 10 seconds. Turn the knob on the reversing valve to the changed bottle.
  • Page 118 Gas system T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...

  • Page 119: Electrical System

    Electrical system Chapter overview 8Electrical system This chapter contains instructions regarding the electrical system of the vehicle. The operation of the electrical appliances of the housing body is described in chapter 9. General safety instructions Only allow qualified personnel to work on the electrical system. All electronic devices (e.g.

  • Page 120: Usb Socket

    Electrical system Capacity Capacity refers to the amount of electricity which can be stored in a battery. The capacity of a battery is given in ampere hours (Ah). The so-called K20 value is normally used. The K20 value indicates how much current a battery is able to dispense over a time period of 20 hours without causing damage, or how much current is required to charge a flat battery within 20 hours.

  • Page 121: 12 V Power Supply

    Electrical system 12 V power supply Only connect devices with a maximum of 10 A to the sockets (Fig. 164,1) of the 12 V power supply. Fig. 164 12 V/10 A socket 8.4.1 Selector switch for radio (special equipment) Depending on the equipment level, a radio with integrated navigation device or a multimedia station will be present, referred to below simply as a "radio".

  • Page 122: Starter Battery

    Electrical system 8.4.2 Starter battery The starter battery serves for starting the engine and supplies the electrical appliances of the base vehicle with voltage. See the instruction manual of the base vehicle for the position of the starter battery. The radio device in the driver’s cabin is connected to the living area battery. Discharging This section contains information regarding the discharge of the starter bat- tery.

  • Page 123: Living Area Battery

    Electrical system When charging the starter battery with an external charger, proceed as fol- lows: Turn off the vehicle engine. Switch off the 12 V power supply on the panel. The indicator lamps or the displays on the panel go out. Switch off all gas appliances, all gas isolator taps and close the regulator tap on the gas bottle.
  • Page 124 Electrical system If the starter battery or living area battery are disconnected, do not apply the ignition. There is a danger of short circuit from exposed cable ends. Take note of the battery manufacturer's users and maintenance instruc- tions. If possible, begin the trip with a fully charged living area battery. Therefore, charge the living area battery before starting the trip.

  • Page 125: Charging Batteries Via A 230 V Power Supply

    Electrical system 8.4.4 Charging batteries via a 230 V power supply If the vehicle is connected to the 230 V power supply, the living area battery and the starter battery are automatically charged by the charger module on the transformer/rectifier. The starter battery is only charged with a float charge. The charging current is adapted to suit the charging condition of the battery.
  • Page 126 Electrical system Fig. 166 Transformer/rectifier (EBL 119) Main supply socket 230 V~ Output: Block 1 - refrigerator Input: Block 2 - control lines Output: Block 4 - heater, safety/drainage valve, basic light (lighting in the entrance area), entrance step Output: Block 3 - panel Output: Block 5 - solar cell (if fitted), spare 2, spare 3, spare 4 Output: Block 6 - solar charge regulator (if fitted) Output: Block 7 - auxiliary charging unit...

  • Page 127: Battery Cut-Off Switch

    Electrical system 8.5.1 Battery cut-off switch After switching the battery cut-off switch back on again: Put the basic light (lighting in the entrance area), entrance step, heater and spare 4 back into service (depending on the model). To do so, switch on the 12 V main switch briefly.

  • Page 128: Charging The Battery

    Electrical system 8.5.4 Charging the battery When the vehicle engine is running, a relay in the transformer/rectifier alter- nator switches on the living area battery and the starter battery together and recharges them with the vehicle generator. When the vehicle engine is switched off, the batteries are automatically disconnected from one another again by the transformer/rectifier.

  • Page 129: V/Tank Gauge For Battery Voltage And Water Or Waste Water Levels

    Electrical system 8.6.2 V/tank gauge for battery voltage and water or waste water levels Battery voltage The V/tank gauge is for the indication of the battery voltage of the starter bat- tery or the living area battery. With the V/tank gauge (Fig. 167,8), note the left scale. The gauge automati- cally lights up as soon as a button is pressed.

  • Page 130: Button For Water Pump

    Electrical system Measure the off-load voltage preferably several hours after the previous charging (e.g. in the morning) and not directly after a current drain. Volume of water/waste The V/tank gauge is for the indication of the quantity of water or waste water. water With the V/tank gauge (Fig.

  • Page 131: Indicator Lamp

    Electrical system 8.6.6 230 V indicator lamp The 230 V indicator lamp (Fig. 167,3) illuminates whenever line voltage is available at the transformer/rectifier input. Further information can be obtained in the manufacturer's instruction manual. Solar installation (special equipment) Protect the solar collectors (solar module) against mechanical overload. The solar installation supplies the most current under optimal sunlight con- ditions.

  • Page 132: 230 V Power Supply

    Electrical system 230 V power supply Only allow qualified personnel to work on the electrical system. Have the vehicle's electrical system checked by a qualified electrician at least once every 3 years. If the vehicle is used frequently, an annual check is recommended.
  • Page 133 Electrical system The vehicle can be connected to an external 230 V power supply. 1 Test button 2 Safety cut-out 3 Fuse box 4 Combined fault current protection switch / safety cut-out Fig. 169 230 V fuse box Connecting the vehicle: Check whether the power supply device is suitable regarding connection, voltage, frequency and current.

  • Page 134: Fuses

    Electrical system Unplug the plug connector from the connection (Fig. 170,1) of the vehicle and remove the connecting cable. Press the seal (Fig. 170,2) of the cable feedthrough into the recess of the service flap gasket. Close the service flap. Fuses Only replace defective fuses when the cause of the defect is known and has been remedied.
  • Page 135 Electrical system Fuses on the living area The fuses are fitted next to the living area battery. battery 1 Jumbo flat fuse 50 A/red (for the transformer/rectifier) 2 Flat fuse 2 A/grey (for battery sensor, living area bat- tery) Fig. 173 Fuses on the living area battery Fuses on the relay box A relay box (AD01) is installed in one of the two seat consoles.
  • Page 136 Electrical system Fuse for the Thetford The fuse is located in the locker wall of the Thetford cassette. toilet (swivel toilet) 1 Flat fuse 3 A/purple Fig. 174 Fuse for the Thetford toilet Changing: Open the flap for the Thetford cassette on the outside of the vehicle. Pull out the Thetford cassette completely.
  • Page 137 Electrical system Model Pull-down bed fuse Overview of electrical Ixeo TL Fuse Spare 3 (25 A) on the transformer/ rectifier pull-down bed fuses Ixeo Time Fuse Spare 3 (25 A) on the transformer/ rectifier and 20 A/2 A fuses in proximity of the pull-down bed motor Lyseo TD front bed Fuse Spare 3 (25 A) on the transformer/...
  • Page 138 Electrical system Changing fuses Lower the pull-down bed with the crank to window height (for emergency (Ixeo Time IT 590): operation, see 6.14.6). Open the window next to the seating group. Remove the cover (Fig. 178,1). Replace fuse. Close the cover. Lift the pull-down bed to the parked position.

  • Page 139: 230 V Fuse

    Electrical system 8.9.2 230 V fuse Check the fault current protection switch for each connection to the 230 V power supply, at least once every 6 months. In international language usage, the fault current protection switch is also denominated RCD (Residual Current Device). Fig.

  • Page 140: External Socket (Special Equipment)

    Electrical system 8.10 External socket (special equipment) 1 TV socket 2 12 V socket 3 SAT socket 4 230 V socket Fig. 182 External socket The 230 V socket and the 12 V socket can be used to power electrical devices in the awning.

  • Page 141: Circuit Diagrams

    Electrical system 8.11 Circuit diagrams 8.11.1 Circuit diagrams, interior Fig. 185 Circuit diagram, interior (EBL 119) T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...
  • Page 142 Electrical system Fig. 186 Connection diagram, panel (LT 96) 2 x AMP flat pins 4.8 x 0.8 Pump + 12 V Lumberg MSFQ 5-pin Full Base waste water tank Lumberg MSFQ 6-pin Full Base water tank n. c. Lumberg MSFQ 9-pin 12 V indicator 12 V main button off 12 V main button on...

  • Page 143: Circuit Diagram, Exterior

    Electrical system 8.11.2 Circuit diagram, exterior Fig. 187 Circuit diagram, exterior Colour of con- Signal ductor X1 Central connector (MCP 12-pole) Tail light, left Tail light, right Direction indicator lamp, left Direction indicator lamp, right Brake light, left Brake light, right Third brake light Fog tail light, left Right fog tail lights...
  • Page 144 Electrical system Colour of con- Colour of con- Signal ductors of wiring ductors of tail harness light Connector for Tail light, left (Superseal 6-pole) Reverse light Fog tail light Direction indicator light Brake light Tail light Connector for Tail light, right (Superseal 6-pole) Reverse light Fog tail light...

  • Page 145: Appliances

    Appliances Chapter overview 9Appliances This chapter contains instructions regarding the appliances of the vehicle. The instructions refer exclusively to the operation of the appliances. Further information about the appliances can be found in the instruction man- uals for the appliances, included separately with the vehicle. General For safety reasons, spare parts for pieces of heating appliances must cor- respond with manufacturer's instructions and be permitted by the manufac-...

  • Page 146: Heater And Boiler

    Appliances Heater and boiler The heater can both heat up the vehicle interior (heating the room air) and heat up the domestic water (boiler function). The following instructions are also valid if the heater is only used as boiler. Never let gas escape unburned due to danger of explosion. Never run the heater in gas operation when refuelling, on ferries or in the garage.

  • Page 147: To Heat Properly

    Appliances 9.2.2 To heat properly Fig. 189 Air outlet nozzle (hot-air heater) Hot air distribution Several air outlet nozzles (Fig. 189) are built into the vehicle. Pipes conduct the warm air to the air outlet nozzles. Turn the air outlet nozzles in a suitable position so the air can escape as required.
  • Page 148 Appliances 1 Display 2 Rotary push button 3 Back button Fig. 190 Operating unit (hot-air heater and boiler) After being switched on, the most recently set values/operating parameters are activated. If no button is pressed, the operating unit switches to stand-by mode after a few minutes.
  • Page 149 Appliances Display area (Fig. 191,8) Lower menu line (Fig. 191,5) Switching operating unit Press and hold the rotary push button (Fig. 191,6) for approx. 3 seconds. on/off: Both menu lines (Fig. 191,3 and Fig. 191,5) are displayed. The first symbol flashes.
  • Page 150 Appliances Turn rotary push button until the required value is displayed: OFF: Hot water production is switched off. 40°: Hot water is heated to 40 °C. 60°: Hot water is heated to 60 °C. BOOST: Fast heating of hot water (boiler priority) for max. 40 minutes. The water temperature is then held at a higher level for two reheating cycles (approximately 62 °C).
  • Page 151 Appliances Keep the water taps open until the water flowing out of the water taps has no bubbles in it. This is the only way to ensure that the boiler is full of water. Close all water taps. Emptying the boiler: Switch off hot water production.

  • Page 152: Alde Hot-Water Heater And Boiler (Special Equipment)

    Appliances Setting the timer: Turn rotary push button (Fig. 191,6) until the timer menu symbol (Fig. 192,9) flashes. Press rotary push button. The start time is displayed and the hour display flashes. Turn rotary push button until the hour of the selected start time is displayed. Press rotary push button.
  • Page 153 Appliances 1 Display (touch screen) 2 "Menu" button 3 "On/Off" button Fig. 194 Operating unit (hot-water heater) When no button is pressed, the operating unit automatically switches to home position after two minutes. Changes to the settings are saved automatically after 10 seconds. Operating buttons The operating buttons have the following functions: Pos.
  • Page 154 Appliances Symbol Signification This symbol appears when a voltage of 230 V is present at the heater The internal temperature is displayed next to this symbol The external temperature is displayed next to this symbol if an external sensor is fitted Adjustment menu The "MENU"...
  • Page 155 Appliances Selecting the operating The hot-water heater can be operated with the following energy sources: mode Gas operation 230 V electrical operation Gas and 230 V electrical operation The operating mode is selected from the operating unit. Selecting gas operation: Press "...
  • Page 156 Appliances Setting the rotational speed of the circulating pump The hot-water heater is equipped with a very powerful pump. In smaller vehicles, the pump can only be operated at full power if the pipes are bled. Otherwise, this will increase wear; loud operating noises are the result. Fig.
  • Page 157 Appliances Alde heat exchanger (special equipment) The heat exchanger only works when the vehicle engine is running. If the heat exchanger is not being used (as in the summer), the heat exchanger on the stopcock should be shut off. The heat exchanger can be used to heat the living area of the vehicle during travel without operating the hot-water heater in the living area.
  • Page 158 Appliances Fig. 200 Auxiliary circulating pump The auxiliary circulating pump (Fig. 200,1) can be used to heat the vehicle engine when parked. The auxiliary circulating pump is connected to the vehicle engine's cooling cir- cuit and thus functions as an engine heater. Fig.

  • Page 159: Wall Flue

    Appliances Set all the water taps to "Hot" and open them. The water pump is turned on. The warm water pipes are filled with water. Keep the taps open until the water flowing out of the taps has no bubbles in it.

  • Page 160: Electrical Floor Warming Unit (Special Equipment)

    Appliances 9.2.6 Electrical floor warming unit (special equipment) On models with electrical floor warming unit, never drill holes in the floor or screw in any screws. Careful with sharp objects. There is danger of a power cut or a short circuit due to damage to a heater wire. Do not cover the transformer.
  • Page 161 Appliances Do not drive on any gradients or inclines greater than 8 % when the air con- ditioning unit is in operation. Otherwise the compressor could be damaged. Do not operate the unit in cooling mode for extended periods when the vehicle is on an incline.
  • Page 162 Appliances Switching off: Press the On/Off button (Fig. 207,2). The lighting can continue to be oper- ated. 1 Air distribution right/left 2 Air distribution ceiling/floor 3 IR receiver, function display, manual on/off 4 Air distribution front/rear Fig. 208 Function display and air distri- bution (air conditioning unit) Operation and display on Certain functions can be operated directly on the unit.
  • Page 163 Appliances When the room temperature set on the remote control is reached, the com- pressor switches itself off and the yellow LED in the IR receiver goes out. The circulation fan continues to run. When the room temperature falls below the set temperature, the unit automat- ically switches itself back to heating mode.

  • Page 164: Telair

    Appliances Dimming the lighting: Press the light button (Fig. 209,5) and keep it pressed until the desired brightness is reached. Switching off the lighting: Press the light button (Fig. 209,5). The Setup button (Fig. 209,4) is used to connect the remote control with the air conditioning unit during first set-up.

  • Page 165: Controlling Truma Appliances With Mobile Terminal (Special Equipment)

    Appliances Switching on: Press the "ON/OFF" button (Fig. 210,7). Press the "Mode" button (Fig. 210,10) as often as required until the required operating mode (Fig. 210,1, 2 or 3) is indicated on the display. The corresponding indicator lamp on the diffusor display (Fig. 211,3) lights up. Use the temperature increase button (Fig.

  • Page 166: Cooker

    Appliances Start Truma app and select the menu items "SETTINGS – Setup Truma iNet-Box – Configure Bluetooth". The individual steps are described in detail in the Truma app. Press the BLUETOOTH button (Fig. 212,1) on the iNet-Box for 1 second. The Truma iNet-Box will be visible in the mobile terminal for approx.

  • Page 167: Gas Cooker

    Appliances 9.5.1 Gas cooker During activation and operation of the gas cooker, no flammable objects or highly inflammable objects such as dishcloths, napkins etc. must be near the gas cooker. Fire hazard! The process of ignition must be visible from above and must not be cov- ered by cooking pans placed on the cooker.

  • Page 168: Gas Oven (Dometic) (Special Equipment)

    Appliances Press the rocker switch (Fig. 213,2 or Fig. 214,1). Ignition sparks are gen- erated at the burner. Once the flame is burning, the control knob must be held down for 10 to 15 seconds, until the thermocouple automatically keeps the gas supply open.
  • Page 169 Appliances Fig. 215 Gas oven (Dometic TecTower) Fig. 216 Gas oven (Dometic) The meaning of the symbols on the control knobs (Fig. 215,1 and Fig. 216,1) of the two gas ovens is identical: stand for the oven stand for the grill. Switching on the oven: Open the regulator tap on the gas bottle and the gas isolator tap "Oven".

  • Page 170: Microwave Oven (Special Equipment)

    Appliances 9.5.3 Microwave oven (special equipment) Only qualified personnel may repair the microwave oven. Improper repairs can cause major risks to the user. The protection device against the escape of microwave energy should never be removed. Use the microwave oven only if it has been properly installed. Only use the microwave oven when the door seal is free of damage.

  • Page 171: Extractor Hood (Special Equipment)

    Appliances 9.5.4 Extractor hood (special equipment) Depending on the equipment, the cooker is equipped with an extractor hood (vented or recirculating). Fig. 218 Vented extractor hood Fig. 219 Recirculating extractor hood Vented extractor hood The kitchen fumes are aspirated above the cooker, cleaned with the aid of a metal grease filter, and blown directly to the outside.

  • Page 172: Refrigerator Ventilation Grill

    Appliances 9.6.1 Refrigerator ventilation grill At high external temperatures, the full cooling power of the cooling unit is only guaranteed if the refrigerator is ventilated sufficiently. In order to achieve a better ventilation the refrigerator ventilation grill can be removed. Fig.

  • Page 173: Dometic Mes/Aes

    Appliances The table below shows the temperature ranges in which the winter cover or the insulated winter cover may be used. Temperature Cover Below 10 °C Winter cover (for refrigerators with capacity below 130 litres: fit only on the lower ventilation grill) Below -5 °C Insulated winter cover (fit only on the lower ventilation grill) If the temperatures are higher than the indicated values, it is absolutely...
  • Page 174 Appliances Gas operation The refrigerator is operated with gas from a connected gas bottle. If LPG is used, the gas burner must be cleaned more frequently. Change-over between During change-over between the different energy sources, intended delays energy sources are installed in the automatic mode (only AES version). This means, that after a change-over to a new energy source the refrigerator can not be operated immediately.
  • Page 175 Appliances If the refrigerator shall be operated with gas: Open the regulator tap on the gas bottle and the gas isolator tap "Refrigerator". Switching on: Press and hold the On/Off button (Fig. 225,1) for about 2 seconds. The refrigerator switches on and the previously set operating mode is dis- played.

  • Page 176: Thetford N3000 E/A

    Appliances The cooling level indicator (Fig. 225,8) shows the operating time of the frame heater for several seconds. Additional functions If, after switching on or after setting, no further button is pressed, the bright- ness of the display is reduced after a few seconds. When pressing a button, the display will light up again.
  • Page 177 Appliances Change-over between During change-over between the different energy sources, intended delays energy sources are installed in the version with automatic power selection. This means, that after a change-over to a new energy source the refrigerator can not be oper- ated immediately.
  • Page 178 Appliances Selecting operating mode: Press and hold the confirmation button (Fig. 226,3) for about 2 seconds. The operating mode symbols flash. Manual power selection: use the arrow keys (Fig. 226,2) to select the desired energy source. Automatic power selection (only version with automatic power selection): use the arrow keys (Fig.

  • Page 179: Thetford N97

    Appliances 9.6.4 Thetford N97 The refrigerator is equipped with a SES (Smart Energy System). It possesses an automatic and a manual power selection system, and an automatic ignition. Operating modes The refrigerator has 3 operating modes: 230 V operation 12 V operation Gas operation The refrigerator always requires a 12 V control voltage, regardless of which type of energy it is using.
  • Page 180 Appliances Operation 1 Operating mode button 2 Display 3 Operating indicator (blue LED) 4 On/Off button 5 Cooling level button Fig. 227 Thetford N97 refrigerator If the refrigerator shall be operated with gas: Open the regulator tap on the gas bottle and the gas isolator tap "Refrigerator". Switching on: Press the On/Off button (Fig.

  • Page 181: Refrigerator Door Locking Mechanism

    Appliances 9.6.5 Refrigerator door locking mechanism With some models, the refrigerator has a separate freezer compartment. The specifications in this section correspondingly also apply to the door of the freezer compartment. During the journey the refrigerator door must always be closed and locked in the closed position.
  • Page 182 Appliances Fig. 230 Locking device (normal posi- Fig. 231 Locking device (ventilation tion) position) Locking in the ventilation Open the refrigerator door. position: Press down the unlocking device (Fig. 230,2). Push locking device (Fig. 230,1) forwards (Fig. 231). If the refrigerator door is closed now, a gap will remain between the refrigerator door and the refrigerator.
  • Page 183 Appliances Thetford The refrigerator is opened and closed with the handle on the door. Opening: Press the handle to the side, keep it pressed and open the refrigerator door. Closing: Close the refrigerator door. The lock hook engages audibly. Ventilation position The refrigerator door may be locked in ventilation position with a swivelling bracket.
  • Page 184 Appliances T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...

  • Page 185: Sanitary Fittings

    Sanitary fittings Chapter overview 10Sanitary fittings This chapter contains instructions regarding the sanitary fittings of the vehicle. 10.1 Water supply, general Fill water tank from supply systems that have been verified to provide drinking water quality. Only use such hoses or containers when filling that have been approved for use with drinking water.

  • Page 186: Water System

    Sanitary fittings 10.2 Water system 10.2.1 Water tank The water tank has a capacity of 110 litres (Travel Van) or 120 litres (other models). In the ready-to-drive state however, the volume has been limited to 20 l (overflow installed) for payload reasons. The panel has not been adjusted to this volume.
  • Page 187 Sanitary fittings Fig. 238 Drain cock (with rocking lever) Fig. 239 Drain cock (with twist cap) Position the vehicle horizontally. Switch on 12 V power supply on the panel. If necessary, switch on the water pump on the panel. Clean or disinfect water system. Close all drain cocks.

  • Page 188: Topping Up The Water

    Sanitary fittings Fig. 241 Filling aid Plug the filling aid (Fig. 241,1) onto the drinking water filler neck. Fill the water tank with drinking water. Use a water hose, a water canister with a funnel or similar for filling. Set all the water taps to "Hot" and open them. The water pump is turned on.

  • Page 189: Closing/Opening The Overflow

    Sanitary fittings 10.2.5 Closing/opening the overflow When filling the water tank, observe the maximum permissible gross weight of the vehicle. Luggage must be reduced accordingly when the water tank is full. Fig. 242 Water tank (central supply unit) Closing: Turn the rotary handle (Fig. 242,1) on the water tank in a clockwise direc- tion as far as it will go.

  • Page 190: Emptying The Water System

    Sanitary fittings 10.2.7 Emptying the water system If the vehicle is not used for several days or if it is not heated when there is a risk of frost, empty the entire water system. Make certain that the water pump is switched off on the panel. Otherwise, the water pump will overheat and may get damaged.
  • Page 191 Sanitary fittings Fig. 246 Safety/drainage valve (Truma) Open the safety/drainage valve (Truma). To do this turn the knob (Fig. 246,1) parallel to the safety/drainage valve. The push button (Fig. 246,2) jumps out. Open the water tank drain. Open all water taps and set to the central position. Hang the shower handset up in the shower position.

  • Page 192: Waste Water Installation

    Sanitary fittings 10.3 Waste water installation Never pour boiling water directly into the sink outlet. Boiling water could cause deformation and leaks in the waste water pipe system. Only empty the waste water tank at disposal stations, camping sites or car- avan sites especially provided for this purpose.

  • Page 193: Heater For Waste Water Tank And Waste Water Pipes (Special Equipment)

    Sanitary fittings Fig. 249 Service flap with square spanner If the vehicle is equipped with a service unit, the square spanner (Fig. 249,1) is fastened on the inside of the service flap. 10.3.2 Heater for waste water tank and waste water pipes (special equipment) In order to prevent waste water fittings freezing up, the waste water tank and the waste water pipes can be electrically heated separately.

  • Page 194: Toilet Compartment

    Sanitary fittings Three LEDs (Fig. 251,1) indicate the status of the control unit for the waste water heating: LED HK 1 is lit Heating circuit 1 is active LED HK 2 is lit Heating circuit 2 is active LED HK 2 is flashing every The device is in the power saving mode 16 seconds LED ERR is flashing...

  • Page 195: Preparing Toilet

    Sanitary fittings 10.5.1 Preparing toilet The sewage tank (cassette) can only be taken out if the sliding trap is closed. Fig. 252 Flap for sewage tank Fig. 253 Sewage tank (example) Open the flap for the sewage tank on the outside of the vehicle. Insert the key into the locking cylinder of the push-button lock (Fig.

  • Page 196: Swivel Toilet

    Sanitary fittings 10.5.2 Swivel toilet The flushing of the Thetford toilet is fed directly from the water system of the vehicle. The toilet bowl can be moved into the optimal position. Fig. 256 Thetford toilet bowl, swivelling Fig. 257 Thetford toilet bowl, swivelling (alternative) The operating unit is located close to the toilet bowl.

  • Page 197: Toilet With Fixed Seat

    Sanitary fittings 10.5.3 Toilet with fixed seat The flushing of the toilet is fed from the water system of the vehicle. Fig. 260 Thetford toilet Fig. 261 Flush button/indicator lamp (Thetford toilet) Flushing: Before flushing open the sliding trap of the Thetford toilet. To do this, turn the slide lever (Fig.

  • Page 198: Emptying The Sewage Tank

    Sanitary fittings 10.5.4 Emptying the sewage tank The sewage tank can only be taken out if the sliding trap is closed. Fig. 262 Flap for the sewage tank Fig. 263 Sewage tank (example) Slide the slide lever on the toilet bowl in a clockwise direction. The sliding trap is closed.

  • Page 199: Care

    Care Chapter overview 11Care This chapter contains instructions regarding the care of the vehicle. At the end of the chapter there is a checklist of measures you must carry out if you are not going to use the vehicle for an extended period of time. The checklist address the following topics: temporary lay-up winter lay-up...

  • Page 200: Washing The Vehicle

    Care 11.1.3 Washing the vehicle Never clean the vehicle in the car wash. Water can penetrate the refriger- ator grills, the waste gas vent or the forced ventilations. The vehicle could be damaged. Wash the vehicle only on a washing site intended for this purpose. Avoid full sunshine.

  • Page 201: Air Suspension (Goldschmitt)

    Care 11.1.6 Air suspension (Goldschmitt) Check periodically whether you can see cracks or brittleness on the bel- lows. Conserve all metal parts of the air suspension system with a protective wax once a year. Remove coarse dirt on the bellows manually with a cloth. Approved cleaning agents are e.g.

  • Page 202: Scratch-Resistant Surface (Kitchen Worktop And Table Top) (Special Equipment)

    Care Clean PVC-floor covering with a mild, soapy cleanser for PVC floors. Do not place carpet on wet PVC-floor covering. The carpet and the PVC-floor covering may stick together. Clean the sink cover manually using water and washing-up liquid. Do not clean the sink cover in the dishwasher.

  • Page 203: Water System

    Care 11.3 Water system 11.3.1 Cleaning the waste water tank Clean the waste water tank after every use. Fig. 264 Cleaning opening of the waste water tank Empty the waste water tank. Open the cleaning opening (Fig. 264,1) on the waste water tank and the drain cock.

  • Page 204: Cleaning The Water Pipes

    Care 11.3.3 Cleaning the water pipes Only use suitable cleaning agents as sold by the specialist trade. The cleaning agent must meet national regulations and be approved (if required). Collect any emerging mixture of water and cleaning agent for correct dis- posal.

  • Page 205: Extractor Hood

    Care 11.4 Extractor hood A metal grease filter is installed in the extractor hood which must be cleaned occasionally. How often cleaning is necessary depends on how often the extractor hood is used. Do not wait to clean the filter until the performance of the extractor hood has noticeably decreased.

  • Page 206: Telair

    Care 11.5.2 Telair Every now and then clean the filter and the ventilation grilles on the outside of the housing. How often cleaning is necessary depends on how often the air conditioning unit is used. Do not wait to clean the filter and the ventilation grill until the performance of the air conditioning unit has noticeably decreased.

  • Page 207: Preparations

    Care 11.6.1 Preparations Check the vehicle for paint and rust damage. Repair damage as neces- sary. Make certain that water cannot penetrate the automatic floor ventilation system and the heater. Use a wax-based rust inhibitor to protect the metal parts of the underbody. Use appropriate protection for external painted surfaces.
  • Page 208 Care Before laying up the vehicle, go through the following checklist: Activities Done Base vehicle Completely fill fuel tank. This prevents corrosion damage within the fuel tank system Jack up vehicle so that the wheels do not bear any load, or move ve- hicle every 4 weeks.

  • Page 209: Winter Lay-Up

    Care 11.7.2 Winter lay-up Additional measures are required if laying up the vehicle over winter: Activities Done Base vehicle Clean body and underbody thoroughly and spray with hot wax or protect with varnish Fill fuel tank with winter diesel Check antifreeze in the cooling water Rectify damage to the paintwork Fill in washer fluid with frost protection Body...

  • Page 210: Starting Up The Vehicle After A Temporary Lay-Up Or After Lay-Up Over Winter

    Care 11.7.3 Starting up the vehicle after a temporary lay-up or after lay-up over winter Go through the following checklist before start-up: Activities Done Base vehicle Check the tyre pressure on all tyres Check the tyre pressure of the spare wheel Body Clean the pivot bearing of the entrance step Check the functioning of the fitted supports...

  • Page 211: Maintenance

    Maintenance Chapter overview 12Maintenance This chapter contains instructions about inspection and maintenance work concerning the vehicle. At the end of the chapter you will find important instructions on how to obtain spare parts. 12.1 Inspection work Like any technical appliance, the vehicle must be inspected at regular inter- vals.

  • Page 212: Living Area Battery

    Maintenance 12.4 Living area battery Observe the following to extend battery life: Keep the battery surface clean and dry. Protect the battery poles and the terminals from corrosion. Check the charging condition periodically or use a charge conservation device. Always keep stored batteries in charged condition and in a cool place. 12.5 Extractor hood The active carbon filter in the recirculating extractor hood must be replaced...

  • Page 213: Checking The Fluid Level

    Maintenance 12.6.1 Checking the fluid level Fig. 265 Compensator reservoir without panel Switch off the hot-water heater and allow it to cool down. Check if the fluid level is between the marks "MIN" (Fig. 265,3) and "MAX" (Fig. 265,2) on the compensator reservoir (Fig. 265). 12.6.2 Topping up heating fluid Position the vehicle horizontally.

  • Page 214: Bleeding The Heating System

    Maintenance 12.6.3 Bleeding the heating system Fig. 266 Bleeding valve of hot-water heater The bleeding valves are built in nearby the radiators. Switch off the hot-water heater and allow it to cool down. Open bleeding valve (Fig. 266,1) and leave open until no more air escapes. Close bleeding valve.

  • Page 215: Front Lights

    Maintenance Types of bulbs Different types of bulbs are used in the vehicle. Below, we have described how to change the different types of bulbs. Fig. 267 Types of bulbs Pos. in Fixture type/bulb Changing Fig. 267 type Plug-in fixture To remove, pull out the bulb To mount, push the bulb into the socket with gentle pressure...

  • Page 216: Rear Lights

    Maintenance 12.7.2 Rear lights 1 Housing screws 2 Rear light 3 Brake light 4 Direction indicator 5 Reverse light 6 Fog tail light Fig. 268 Rear lights Undo the five housing screws (Fig. 268,1). Remove housing. Remove bulb. Put in a new bulb. Reassemble the lamp in the reverse order.

  • Page 217: Types Of Bulbs For Exterior Lighting

    Maintenance 12.7.4 Types of bulbs for exterior lighting Exterior lighting Type of bulb Rear Brake light Ba15s 12 V 21 W Rear light Ba15s 12 V 5 W Direction indicator Ba15s 12 V 21 W orange Fog tail light Ba15s 12 V 21 W Licence plate light Soffitte 12 V 5 W Reverse light...

  • Page 218: Spotlight (Movable)

    Maintenance 12.8.1 Spotlight (movable) Fig. 270 Spotlight (movable) LED 12 V/max. 10 W Changing bulbs: Turn the spotlight (Fig. 270,1) by 90° and remove from rail. Remove LED (Fig. 270,2) with a suction cup. Press a new LED into the holder. Insert spotlight into the rail.

  • Page 219: Spare Parts

    Maintenance 12.9 Spare parts Every alteration of the original condition of the vehicle can alter road behaviour and jeopardize road safety. The special equipment and original spare parts recommended by us have been specially developed and supplied for your vehicle. These products are available at the authorised dealer or service centre.

  • Page 220: Vehicle Identification Plate

    Maintenance 12.10 Vehicle identification plate 1 Chassis number Fig. 272 Vehicle identification plate The vehicle identification plate (Fig. 272) with the chassis number is located inside in the entrance area. Do not remove the vehicle identification plate. The vehicle identification plate: Identifies the vehicle Helps with the procurement of spare parts Together with the vehicle documents identifies the vehicle owner...

  • Page 221: Wheels And Tyres

    Wheels and tyres Chapter overview 13Wheels and tyres This chapter contains instructions regarding the tyres of the vehicle. At the end of the chapter there is a table you can use to find the correct tyre pressure for your vehicle. 13.1 General Check tyre pressure before a journey or every 2 weeks.

  • Page 222: Tyre Selection

    Wheels and tyres Fig. 273 Tighten the wheel nuts or wheel bolts cross-wise Check regularly that the wheel nuts or wheel bolts are firmly seated. Re-tighten the wheel nuts or wheel bolts of a changed wheel after 50 km (30 miles) (Fig. 273). See section 13.5.2 for tightening torque.

  • Page 223: Tyre Specifications

    Wheels and tyres 13.3 Tyre specifications Description Explanation 215/70 R 15C 109/107 Q Tyre width in mm (example) Height-to-width proportion in percent Tyre design (R = radial) Rim diameter in inches Commercial (transporter) Load index code for single tyres Load index code for twin tyres Speed index (Q = 160 km/h) 13.4 Handling of tyres...

  • Page 224: Changing Wheels

    Wheels and tyres 13.5 Changing wheels 13.5.1 General instructions The vehicle must be on level, firm ground, secure from slipping. Go into first gear. In the case of automatic transmission, change gear to "P" position. Before jacking up the vehicle firmly apply the handbrake. Prevent the vehicle from rolling away by blocking the opposite wheel with the wheel chocks.

  • Page 225: Tightening Torque

    Wheels and tyres 13.5.2 Tightening torque Depending on the wheel rim type and the wheel manufacturer, the wheels must be tightened with different tightening torques. Description Tightening torque Steel wheel rims 15" 160 Nm 16" Fiat/Citroen Light 160 Nm 16" Fiat/Citroen Heavy 180 Nm Fig.

  • Page 226: Changing A Wheel

    Wheels and tyres 13.5.3 Changing a wheel The footplate of the vehicle jack must be levelly positioned on the ground. Do not tilt the vehicle jack. The wheel you have replaced should be repaired immediately. Take note of the general instructions in this chapter. Fig.

  • Page 227: Spare Wheel Support (Special Equipment)

    Wheels and tyres 13.6 Spare wheel support (special equipment) The spare wheel support is built into the rear garage. Fig. 280 Spare wheel support in the rear garage Removing the spare wheel: Open external flap of the rear garage. Loosen and remove both fixing screws (Fig. 280,2) with the on-board tool set.
  • Page 228 Wheels and tyres The information on pressure levels is valid for cold tyres and loaded vehi- cles. Pressure in hot tyres must be 0.3 bar higher than in cold tyres. Recheck the pressure when the tyres are cold. Tyre pressures in bar. The tyre pressure tolerance is +/- 0.05 bar.

  • Page 229: Troubleshooting

    Troubleshooting Chapter overview 14Troubleshooting This chapter contains instructions about possible faults in your vehicle. The faults are listed with their possible causes and corresponding remedies. The specified faults can be remedied with relative ease and without a great deal of specialised knowledge. In the event that the remedies detailed in this instruction manual should not be successful, an authorised specialist work- shop must find and eliminate the cause of the fault.

  • Page 230: Electrical System

    Troubleshooting Fault Cause Remedy The satellite unit cannot The vehicle engine is Switch the vehicle engine be switched on running Remote control battery is Change the battery empty Fuse on the supply cable Replace fuse is damaged Further faults can occur, which are shown by an error code on the display of the operating panel.
  • Page 231 Troubleshooting Fault Cause Remedy Living area battery over- Battery selection switch Move position of battery loaded ("hot") set wrongly selection switch Defective load sensor or Contact customer service relay 12 V power supply does 12 V power supply is Switch 12 V power not work switched off supply on...

  • Page 232: Gas System

    Troubleshooting Fault Cause Remedy 12 V indicator lamp does 12 V power supply is Switch 12 V power not light up switched off supply on Battery cut-off switch on Set battery cut-off switch the transformer/rectifier is to on switched off Starter or living area Charge the starter or battery is not charged...

  • Page 233: Heater/Boiler

    Troubleshooting 14.6 Heater/boiler In the event of a defect contact the nearest customer service workshop of the relevant appliance manufacturer. The list of addresses is enclosed with the accompanying appliance documentation. Only authorised qualified personnel may repair the appliance. 14.6.1 Truma heater/boiler with CP plus digital operating unit Fault Cause...
  • Page 234 Troubleshooting Error code Cause Rectification Fault search # 17 Summer operation with empty Switch off the device and allow water container it to cool down. Fill the boiler instruction with water Warm air louvres blocked Check outlet openings Air circulation suction system Remove blocking of air circula- blocked tion suction system...

  • Page 235: Alde Heater/Boiler

    Troubleshooting 14.6.2 Alde heater/boiler If a fault occurs in the system, the cause is shown on the display. Fault Cause Remedy Heater does not ignite Lack of gas Open regulator tap and with gas operation gas isolator tap Connect a full gas bottle Heater does not ignite Battery voltage too low Charge battery.

  • Page 236: Air Conditioning Unit

    Troubleshooting 14.7 Air conditioning unit 14.7.1 Truma Fault Cause Remedy Air conditioning unit does No 230 V power supply Connect the vehicle to not start up the local power supply 230 V automatic circuit Switch on the 230 V breaker has triggered automatic circuit breaker Remote control is not Remote control batteries...

  • Page 237: Telair

    Troubleshooting 14.7.2 Telair Fault Cause Remedy Air conditioning unit does No 230 V power supply Connect 230 V power not start up supply 230 V automatic circuit Switch on the 230 V breaker has triggered automatic circuit breaker Remote control batteries Change batteries empty (2 x AAA)

  • Page 238: Microwave Oven

    Troubleshooting 14.8.2 Microwave oven Only qualified personnel may repair the microwave oven. Improper repairs can cause major risks to the user. Fault Cause Remedy Microwave oven does not Fuse is defective Replace fuse cut in Door of the microwave Remove foreign bodies oven is not properly stuck in the door of the closed...

  • Page 239: Dometic Mes/Aes

    Troubleshooting 14.9.2 Dometic MES/AES In the event of a fault, the illuminated Fault button will flash. Also, either one of the illuminated buttons for operating mode or the cooling level indicator will flash. In addition, a warning signal will sound. Fault Cause Remedy...

  • Page 240: Thetford N 3000

    Troubleshooting 14.9.3 Thetford N 3000 For certain faults, indicators also flash on the operating panel. Fault Cause Remedy LEDs for types of energy Refrigerator does not Switch refrigerator off and display of the tem- work and on again perature range flash Check availability of an energy source LED "...

  • Page 241: Water Supply

    Troubleshooting 14.10 Water supply Fault Cause Remedy Leakage water inside the A leak has occurred Identify leak, re-connect vehicle water pipes No water Water tank is empty Replenish drinking water Drain cock not closed Close drain cock 12 V power supply is Switch 12 V power switched off supply on...

  • Page 242: Body

    Troubleshooting Fault Cause Remedy Any change in the taste Tank filled with dirty Clean water system or odour of the water water mechanically and chemi- cally; then disinfect and rinse copiously with drinking water Fuel filled into the water Clean water system tank by mistake mechanically and chemi- cally;...

  • Page 243: Pull-Down Bed, Electrically Operated (Ixeo Tl)

    Troubleshooting Fault Cause Remedy Electric pull-down bed Fuse on the transformer/ Replace fuse does not move rectifier or on the pull- down bed drive motor faulty Living area battery is Charge the living area empty or the transformer/ battery rectifier has switched off due to insufficient voltage Drive is defective In an emergency, the...
  • Page 244 Troubleshooting Fault Cause Remedy Alarm LED and Pro- System fault The pull-down bed must gramme LED flash simul- be newly programmed. taneously every Contact customer service 0.5 seconds Alarm LED flashes every System fault Bring the pull-down bed 0.5 seconds and Pro- into the top end position;...

  • Page 245: Special Equipment

    Special equipment 15.1 Weight details for special equipment 15Special equipment The use of accessories, parts and fittings not supplied by us may cause damage to the vehicle and jeopardize road safety. Even if an expert's report, a general type approval or a design certification exists, there is no guarantee for the proper quality of the product.
  • Page 246 Special equipment Item designation Surplus weight (kg) CPU remote display Floor warming unit Gas oven/grill Gas bottle (11 kg) made of aluminium Gas alarm system Holder for flat screen Rear garage door, left Truma Combi 6 E heater Insect screen, door (full height) Driver's cabin air conditioning unit Air conditioning unit (Telair) Air conditioning unit (Truma)
  • Page 247 Special equipment Item designation Surplus weight (kg) Winter insulation mat, outside Conversion door central locking mechanism Auxiliary battery Engine variants The vehicle mass in a ready-to-drive state relates to the base vehicle. If a more powerful engine is fitted, the mass increases in a ready-to-drive state. Engine variant Surplus weight (kg) Fiat 2.3 Mjet...
  • Page 248 Special equipment T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...

  • Page 249: Technical Data

    * Access via service flap ** Beneath the vehicle Specifications without guarantee Lyseo TD Harmony Line Fig. 283 Ground plan Lyseo Harmony Line TD 590 Fig. 284 Ground plan Lyseo Harmony Line TD 690 T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...
  • Page 250 Technical data Fig. 285 Ground plan Lyseo Harmony Line TD 700 Fig. 286 Ground plan Lyseo Harmony Line TD 710 G Fig. 287 Ground plan Lyseo Harmony Line TD 728 G T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...
  • Page 251 Technical data Fig. 288 Ground plan Lyseo Harmony Line TD 734 Fig. 289 Ground plan Lyseo Harmony Line TD 744 Fig. 290 Ground plan Lyseo Harmony Line TD 745 T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...
  • Page 252 Technical data Travel Van Fig. 291 Ground plan Travel Van T 590 G Fig. 292 Ground plan Travel Van T 620 G Nexxo Time Fig. 293 Ground plan Nexxo Time T 569 T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...
  • Page 253 Technical data Fig. 294 Ground plan Nexxo Time T 660 Fig. 295 Ground plan Nexxo Time T 690 G Ixeo Time Fig. 296 Ground plan Ixeo Time IT 590 Fig. 297 Ground plan Ixeo Time IT 710 G T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...
  • Page 254 Technical data Fig. 298 Ground plan Ixeo Time IT 726 G Fig. 299 Ground plan Ixeo Time IT 734 Ixeo TL Fig. 300 Ground plan Ixeo TL IT 640 Fig. 301 Ground plan Ixeo TL IT 680 T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...
  • Page 255 Technical data Fig. 302 Ground plan Ixeo TL IT 728 G Fig. 303 Ground plan Ixeo TL IT 734 T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...

  • Page 256: Table Of Linear Measures

    Technical data 16.2 Table of linear measures Type Wheelbase in Length in cm Width in cm Height in cm Lyseo TD Harmony Line 710 G 728 G Travel Van T 590 G T 620 G Nexxo Time T 569 T 660 T 690 G Ixeo Time IT 590...

  • Page 257: Helpful Notes

    Helpful notes Chapter overview 17Helpful notes This chapter contains helpful tips for the journey. At the end of the chapter there is a checklist containing the most important equipment for the journey. 17.1 Traffic rules in foreign countries The vehicle driver is required to inform himself as to the traffic rules of the countries in which he plans to travel before beginning the trip.

  • Page 258: Gas Supply In European Countries

    Helpful notes 17.3 Gas supply in European countries In Europe, there are several different connection systems for gas bottles. It is not always possible to fill or exchange your gas bottles in a foreign country. Get information about the connection system in the country you are travelling to before embarking on your journey, e.g.

  • Page 259: Tips For Winter Campers

    Helpful notes When parking on open space keep emergency routes clear. The way to the driver's seat should be clear. The ignition key should always be within reach. Only take with you those valuables which are absolutely necessary for the journey.

  • Page 260: Travel Checklists

    Helpful notes 17.7 Travel checklists The following checklists will help that nothing important is left at home although not everything on the checklists might be necessary. Do not leave checking of documents (e.g. vehicle papers and information) as well as checking the condition of the vehicle until just before com- mencing the trip.
  • Page 261 Helpful notes Object Object Object Vehicle/tools Waste water con- Gas tube Snow chains (win- tainer ter) Adapter socket Fabric tape Screwdriver CEE adapter Watering can for Current-measuring drinking water instrument Wire Cable reel Step Spare wheel V-belt Wheel chocks Spare lamps Glue First-aid kit Spare fuses...
  • Page 262 Helpful notes T-Modell - 17/18 - Ausgabe 09/17 - 2891569 - BUE-0029-19EN...

  • Page 263: Inspection Plan

    Inspection plan 18Inspection plan Pos. Component Activity Interval Auxiliary support Lubrication Annually Tyres and wheel rims Air pressure check Annually (see section 13.7). Visual check for damage Outside lighting Function check Annually Joints, hinges Lubrication Annually Refrigerator, heater, boiler, cook- Function check Annually er, lighting, flap and door closures,...
  • Page 264 Inspection plan Delivery Pos. 1-14 Stamp of the Bürstner dealer Date Signature 1st year Pos. 1-14 2nd year Pos. 1-17 Stamp of the Bürstner dealer Stamp of the Bürstner dealer Date Signature Date Signature 3rd year Pos. 1-14 4th year Pos.
  • Page 265 Index 12 V fuses ......134 Switching on ......162 For Thetford toilet .
  • Page 266 Index Hot water production, switching on ..149 Roman shade ..... . .202 Operating modes ....151 Scratch-resistant surface .
  • Page 267 Index Conventional load ..... . . 19 Driving speed ......36 Conversion door .
  • Page 268 Index Fire prevention ......11 Heater for waste water pipes ...136 Fire risks, avoidance .
  • Page 269 Index Heater ....... 146 Operating modes ....155 Air outlet nozzles, adjustment .
  • Page 270 Index Leakage water inside the vehicle ... 241 Hot-water heater .....212 Leather covers, cleaning .
  • Page 271 Index Refrigerator door Button for water pump ....130 Closing ......183 Connection diagram .
  • Page 272 Index Road safety ......12 Insect screen ......86 Towing .
  • Page 273 Index Suspension table Travel cots suitable for children ..94 Conversion to bed foundation ... 88 Troubleshooting ......229 Extending .
  • Page 274 Index Water tank ......186 Cleaning ......203 Unladen weight .

This manual is also suitable for:

Lyseo harmony line td 700Lyseo harmony line td 710 gLyseo harmony line td 734Lyseo harmony line td 744Travel van t 590 gLyseo harmony line td 745 ... Show all

Table of Contents

Save PDF