Related Manuals for Baumatic BT6.3GL
Summary of Contents for Baumatic BT6.3GL
- Page 1 BT6.3GL/BT6.3BGL BT7.3GL/BT7.3BGL BT9.3GL/BT9.3BGL BT10.3GL/BT10.3BGL Glass chimney hood...
- Page 2 User Manual for your Baumatic BT6.3GL/BT6.3BGL BT7.3GL/BT7.3BGL BT9.3GL/BT9.3BGL BT10.3GL/BT10.3BGL Cooker Hood Glass chimney hood NOTE : This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference;...
-
Page 3: Table Of Contents
Specifications of your cooker hood 8 - 11 BT6.3GL / BT6.3BGL BT7.3GL / BT7.3BGL BT9.3GL / BT9.3BGL BT10.3GL / BT10.3BGL Using your Baumatic cooker hood 12 - 13 Before first use To use your cooker hood 12 – 13 Cleaning your Baumatic cooker hood 13 –... -
Page 4: Environmental Note
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. -
Page 5: Important Safety Information
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Customer Care Department. - Page 6 o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTER! o If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type.
- Page 7 o Remember that when in extraction mode, your cooker hood is removing air from your room. Ensure that proper ventilation measures are being observed. o Note that the cooker hood removes odours from your kitchen, not steam. o Warning - Always ensure that the cooker hood been disconnected...
-
Page 8: Specifications Of Your Cooker Hood
Specifications of your cooker hood BT6.3GL / BT6.3BGL Dimensions: Width (canopy): 600 mm Height (with chimney): 583 – 1063 mm Depth (canopy): 500 mm Dimensions of the chimney section: 303 mm x 276 mm Specifications: o High extraction tangential motor... -
Page 9: Bt7.3Gl / Bt7.3Bgl
1 x Washable metallic grease filter o 2 x Halogen lights o Extraction capacity: 500 m³/hr o Noise level min/max: 61 – 66 dB o Optional Extra: 1 x S1 pair of carbon filters for air recirculation mode (available from the Baumatic Spares Department). -
Page 10: Bt9.3Gl / Bt9.3Bgl
2 x Washable metallic grease filters o 2 x Halogen lights o Extraction capacity: 500 m³/hr o Noise level min/max: 61 – 66 dB o Optional Extra: 1 x S1 pair of carbon filters for air recirculation mode (available from the Baumatic Spares Department). -
Page 11: Bt10.3Gl / Bt10.3Bgl
2 x Washable metallic grease filters o 2 x Halogen lights o Extraction capacity: 500 m³/hr o Noise level min/max: 54 – 62 dB o Optional Extra: 1 x S1 pair of carbon filters for air recirculation mode (available from the Baumatic Spares Department). -
Page 12: Using Your Baumatic Cooker Hood
Using your Baumatic cooker hood Before first use IMPORTANT: THIS PROCESS MUST BE FOLLOWED BEFORE THE COOKER HOOD IS USED FOR THE FIRST TIME. o You should use a good quality stainless steel cleaner on ALL of the stainless steel areas of your cooker hood, before it is used for the first time. -
Page 13: Cleaning Your Baumatic Cooker Hood
OR AT THE VERY LEAST WHEN YOU BEGIN COOKING. YOU SHOULD ALSO RUN YOUR HOOD FOR TEN MINUTES AFTER YOU HAVE FINISHED COOKING. Cleaning your Baumatic cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, SET AT THE WALL FROM THE CABLE. -
Page 14: The Grease Filter
The grease filter o Your cooker hood includes a grease filter which helps to absorb grease particles to protect your kitchen & furniture from greasy residues. o The metallic filter may become flammable if it becomes saturated with this greasy residue. o To prevent this fire hazard, the filter should be cleaned regularly. -
Page 15: Changing A Light Bulb
o Refit the grease filter once it has dried. o IMPORTANT: Let the grease filter dry thoroughly before refitting it in the cooker hood. Changing a light bulb IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. -
Page 16: Fitting The Carbon Filters
o Use a screwdriver to remove the glass cover that sits over the bulb. Unscrew the light bulb that needs to be replaced and insert a new G4 20W (max) bulb. Then replace the glass cover. o IMPORTANT: Defective bulbs should be replaced immediately. o If the lights still do not work, make sure that the bulbs are fitted properly into their housings before you call for technical assistance. -
Page 17: Installation
3) Turn the carbon filter anticlockwise, until you feel it click into place. o Repeat this process for the second carbon filter. You need to place a carbon filter at either end of the motor. o Refit the grease filter. o The carbon filters should be replaced every three months, or if they show signs of damage. -
Page 18: Before Beginning Installation
o The cooker hood’s power cable must be fitted upstream from the electrical connection, using an omni-polar switch with a contact distance of at least 3 mm. THE FUSE MUST BE RATED AT 3 AMPS. WARNING: THIS APPLIANCE MUST BE EARTHED. It should only be connected by a competent person, using fixed wiring via a double pole switched fused spur outlet. -
Page 19: Installing Your Cooker Hood
o Check inside the product and ensure that there is no transit packaging or any other materials, such as packets of screws, guarantees etc. These should be removed and kept for future use. o If possible, disconnect and move freestanding or slot-in cookers from their position, to provide easier access to the rear wall and ceiling. - Page 20 2) Position the hood against the wall that you are intending to install it on and mark the position of the support holes that are to be drilled (as shown in the figure below). 2a) The support screw holes are indicated by figure A in this drawing and the anchoring screw holes are indicated by figure B.
- Page 21 4) Insert rawl plugs into all of the holes that you have drilled. 5) Fasten the support screws halfway in, leaving them 10 mm out of the wall. 6) Hang the hood onto the support screws. 7) Fully tighten the support screws (A) and then screw the anchoring screws (B) through the relevant holes in the cooker hood.
-
Page 22: Connecting To External Ducting
Connecting to external ducting 8) Connect the coupling to the top of the cooker hood, and then connect a 125 mm ducting hose to the coupling (please note that the ducting hose is not supplied with the appliance). o The other end of the ducting hose should be connected to a discharge outlet that is suitable for cooking vapours. - Page 23 10) Lift chimney section D upwards until it reaches the ceiling. You must ensure that it is perpendicular to the hood. o Mark the side measurements of both sides of chimney section D on the wall with a pencil and then remove chimney section D. 11) Take the fixing bracket (E) and place it between the two pencil marks that you made in step 9.
- Page 24 12) Using an 8 mm drill bit, drill out two holes on the pencil markings that you made in step 11. Insert rawl plugs into the holes and then use a screwdriver to secure the fixing bracket to the wall. o Refit chimney section C to the hood and fix it onto the hood using the two screws that are supplied.
-
Page 25: Attaching The Glass Canopy
Attaching the glass canopy o The anchoring bolts (F) should be found with the other brackets and screws provided with the cooker hood. If you find them already attached to the cooker hood, then you should unscrew them. o Carefully place the glass section (Q) on the upper surface of the cooker hood and then slide it back towards the wall. -
Page 26: Completing The Installation
Completing the installation If you are setting the appliance to recirculation mode, then you should now fit the two carbon filters. See the “Fitting the carbon filters” section on pages 16 - 17. The electrical connection must correspond to the electrical requirement noted on the rating plate, which is placed inside the cooker hood. -
Page 27: Troubleshooting
Troubleshooting IMPORTANT: If your cooker hood appears not to be operating properly, before contacting the Baumatic Customer Care Department, please refer to the checklist below. My cooker hood will not start. o Check that the hood is connected to the electricity supply o Check that the fan speed control is set correctly. - Page 28 Or any installation other than the one specified by Baumatic Ltd. has been completed. Please refer to the conditions of guarantee that appear on the...
-
Page 29: Baumatic Consumables
BC005 Stainless Steel Cleaner and Protector (250 ml) o BC007 E-Cloth – General Purpose Cloth o BC008 Microwave Cover To order a Baumatic consumable product please call 0123 5437 244 and quote the product code. You can also order online from eshop.baumatic.co.uk... -
Page 30: Contact Details
Czech Republic Baumatic CR spol s.r.o. United Kingdom Lìpovà 665 Baumatic Ltd., 460 01 Liberec 4 Baumatic Buildings, Czech Republic 6 Bennet Road, Reading, Berkshire +420 483 577 200 RG2 0QX United Kingdom www.baumatic.cz Sales Telephone Slovakia (0118) 933 6900 Baumatic Slovakia, s.r.o.
Need help?
Do you have a question about the BT6.3GL and is the answer not in the manual?
Questions and answers