Related Manuals for DeWalt DCD985-XE
Summary of Contents for DeWalt DCD985-XE
- Page 1 INSTRUCTION MANUAL DCD985-XE 18 V HEAVY-DUTY 13 mm (1/2") CORDLESS HAMMERDRILL/DRILL/DRIVER...
-
Page 3: Definitions: Safety Guidelines
1) WORK AREA SAFETY Definitions: Safety Guidelines a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the The definitions below describe the level of severity for each signal presence of flammable liquids, gases or dust. -
Page 4: Electrical Safety
c) Prevent unintentional starting. Ensure the switch is in the off position g) Use the power tool, accessories and tool bits etc., in accordance with before plugging in. Carrying power tools with your finger on the switch or these instructions and in the manner intended for the particular type of plugging in power tools that have the switch on invites accidents. -
Page 5: Extension Cords
• Replacement of the supply cord. If the supply cord is damaged, it must be hands. Operating this tool with one hand will result in loss of control. Breaking replaced by the manufacturer or an authorised D WALT Service Centre in order through or encountering hard materials such as re-bar may be hazardous as well. -
Page 6: Important Safety Instructions For All Battery Packs
respiratory protection appropriate for the dust exposure. Direct particles away from • NEVER force the battery pack into the charger. DO NOT modify the battery face and body. pack in any way to fit into a non-compatible charger as battery pack may rupture causing serious personal injury. -
Page 7: Important Safety Instructions For All Battery Chargers
• If battery contents come into contact with the skin, immediately wash area • Pull by the plug rather than the cord when disconnecting the charger. This will with mild soap and water. If battery liquid gets into the eye, rinse water over the reduce the risk of damage to the electric plug and cord. -
Page 8: Charge Indicators
Charging Procedure (Fig. 1) FIG. 1 HOT/COLD DELAY This charger has a hot/cold delay feature: when the charger detects a battery that is 1. Plug the charger into an appropriate outlet hot, it automatically starts a delay, suspending charging until the battery has cooled. before inserting the battery pack. -
Page 9: Storage Recommendations
A. Trigger switch I. Battery pack c. Move the charger and battery pack to a location where the surrounding air temperature is approximately 18° – 24°C (65°F and 75°F); B. Forward/reverse control button J. Battery release button d. If charging problems persist, take the tool, battery pack and charger to your C. - Page 10 If model is not equipped with side handle, grip drill with one hand on the handle and one hand on the battery pack. NOTE: Side handle comes equipped on the DCD985-XE. Forward/Reverse Control Button (Fig. 2) A forward/reverse control button (B) determines the direction of the tool and also...
- Page 11 SCREWDRIVING (FIG. 4) WARNING: Always ensure the bit is secure before starting the tool. A loose bit Rotate the mode control collar (F) so the screw symbol is aligned with the arrow. may eject from tool causing possible personal injury. NOTE: The torque adjustment collar may be set to any number at any time.
-
Page 12: Operation
Drilling (Fig. 3) WARNING: To reduce the risk of serious personal injury, DO NOT suspend tool overhead or suspend objects from the belt hook. ONLY hang tool’s belt hook from a NOTICE: If drilling thin material, use a wood “back-up” block to prevent damage to the work belt. -
Page 13: Maintenance
Lubrication 2. Rotate the mode control collar (F) so the screw symbol is aligned with the arrow. 3. Make a few practice runs in scrap or unseen areas of the workpiece to determine Your power tool requires no additional lubrication. the proper position of the torque adjustment collar. - Page 14 MAXIMUM RECOMMENDED CAPACITIES DCD985-XE WOOD Auger 32 mm (1-1/4") Paddle 38 mm (1-1/2") Twist 13 mm (1/2") Self-feed 65 mm (2-9/16") Hole saw 100 mm (4") METAL Twist 13 mm (1/2") Hole saw 35 mm (1-3/8") MASONRY Carbide 13 mm (1/2")
- Page 16 The battery voltage is nominal, it can measure above or below depending on the state of charge. Stanley Black & Decker 701 East Joppa Road, Baltimore, MD 21286 • 82 Taryn Drive, Epping, VIC 3076 Australia (MAR11) Part No. N106260 DCD985-XE Copyright © 2011 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...