Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AT&T U-verse
Summary of Contents for AT&T U-verse
- Page 2 Your new remote control, along with the USB converter, provides you with the flexibility of no longer having to "point" your remote control at the U-verse Receiver in order to change channels or access any of the receiver features. Since this is a Universal Remote Control, you have the ability to program up to three additional devices, such as a TV or DVD player.
-
Page 3: Table Of Contents
Table of Contents Function Keys of Your RF Remote Control ..............3 Quick Setup Guide .........................4 How to activate the batteries .....................4 How to install the USB Converter ..................4 Setting up your Remote to control other devices (TV/DVD/etc) ......5 3A. Search for Device Codes ....................6 3B. -
Page 4: Function Keys Of Your Rf Remote Control
Function Keys of Your RF Remote Control POWER Key Mode Keys (AT&T TV DVD AUX) Ready to Learn (Green LED) SCAN BACK - FWD LEARN Key OK Key Select Key to Learn Backlit Group - (Red LED) Pause, Menu, Guide, Mute, Last FWD Key VOLUME UP / DOWN CHANNEL UP / DOWN... -
Page 5: Quick Setup Guide
Pairing Button STEP 2. Plug the USB Converter into the USB Power LED port on the front of your AT&T U-verse Receiver. Your port location may differ from the picture shown. The blue power LED on the USB Converter will... -
Page 6: Setting Up Your Remote To Control Other Devices (Tv/Dvd/Etc)
Quick Setup Guide NOTE: The USB Converter must be installed in the front USB port of the U-verse Receiver only. It will not operate if installed in the USB ports on the back of the receiver. NOTE: After installing the USB Converter, test the POWER, CHANNEL and VOLUME keys for proper operation. -
Page 7: Search For Device Codes
Quick Setup Guide 3A. Search for Device Codes The Search method will scan through all the IR codes to find one that works with your TV or other device. MODE KEYS STEP 1. Power on the device to be programmed. STEP 2. - Page 8 Quick Setup Guide Search for Device Codes (continued) NOTE: If the device does not turn off and you have searched all available codes, you will hear 8 beeps and the mode key will flash 8 times. If this happens, please start over at Step 2 or proceed to 3B, Learning Device Codes.
-
Page 9: Learning Device Codes
The other mode keys will stop flashing. The red LED SELECT KEY TO LEARN indicator on your U-verse remote will flash. STEP 3. Place the RF Remote Control head-to-head with your original remote (about 1” – 2” apart). - Page 10 Quick Setup Guide Learning Device Codes (continued) STEP 6. Press the next key you want to program on your RF Remote Control once (VOLUME or VOLUME or MUTE STEP 7. Press and hold the corresponding key you want programmed from the original remote until the RF Remote Control emits a 1”-2”...
-
Page 11: Advanced Features Setup
Volume controls (VOL+ or -, MUTE) will go to the TV, and the Channel controls (CH+ or -, LAST) will be sent to the U-verse Receiver. Once you have programmed a device to a mode key, you can send the volume commands to that device rather than the TV or U-verse Receiver (e.g. a home theatre receiver). - Page 12 Advanced Features Setup A2. Send Volume or Channel Commands only to the Device Mode Selected (e.g. in DVD mode, the DVD player controls the audio, but in TV mode the TV controls the audio) STEP 1. Press and hold both the AT&T and OK keys for one second, then release.
-
Page 13: Power Control Options
By factory default, the POWER key only operates the AT&T U-verse Receiver. Once you have programmed the TV mode key, both the TV and the AT&T U-verse Receiver will be powered ON and OFF at the same time. In normal operation, you can turn programmed devices ON or OFF individually by pressing the appropriate mode key, and then the POWER key. - Page 14 Advanced Features Setup B2. To Power Devices On and Off Independently STEP 1. Press and hold both the AT&T and OK keys for one second, then release. All the mode keys flash twice. STEP 2. Enter 9 7 7 using the numeric keypad. The AT&T key flashes twice.
-
Page 15: Backlight Cancellation Feature
Advanced Features Setup C. Backlight Cancellation Feature Your RF Remote Control has the ability to turn the keypad backlighting ON or OFF. If you wish to use this feature to extend battery life, follow these instructions. Turning the Keypad Backlighting OFF STEP 1. -
Page 16: Home Id
Advanced Features Setup Turning the Keypad Backlighting ON (continued) STEP 2. Enter 9 9 1 using the numeric keypad. The AT&T key will give a long flash and a long beep, indicating successful programming. The RF Remote Control then returns to its normal state. - Page 17 Advanced Features Setup Home ID (continued) NOTE: The USB converter will remain in programming mode for two minutes to receive the Home ID command from the RF Remote Control. If the blue LED light turns on, it means the USB converter timed out and you must start over. STEP 2.
-
Page 18: Change To Ir Control Only (Deactivate Rf Control)
E. Change to IR Control Only (deactivate RF Control) Your RF Remote Control is set to operate your AT&T U-verse Receiver using an RF (radio frequency) signal. The USB Converter allows the RF signal from your RF Remote Control to communicate with your U-verse IR receiver. -
Page 19: Restoring Factory Defaults
Advanced Features Setup F. Restoring Factory Defaults F1. Return all programmed codes to Factory Default (including “Learned” codes) STEP 1. Press and hold both the AT&T key and OK key for one second, then release. STEP 2. All the mode keys flash twice. STEP 3. -
Page 20: Troubleshooting
Check to be sure the batteries are installed properly (see above). Use only Alkaline batteries. Batteries may be weak and need to be replaced. Issue: My remote control does not control my U-verse receiver; I can’t change channels. Make sure the converter is properly installed and the blue LED is lit. - Page 21 To avoid interference from other RF remotes, See Section D: Home ID (Page 15). Issue: I programmed my TV and Home Theater system to come on with my U-Verse Receiver, but the Home Theater system turns off when I turn the others on.
-
Page 22: Care And Maintenance
Care and Maintenance 1. Keep the remote dry. If it gets wet, wipe it dry immediately. 2. Use and store the remote only in normal temperature environments. 3. Handle the remote gently and carefully. Don’t drop it. 4. Wipe the remote with a clean cloth occasionally to keep it looking new. 5. -
Page 23: Fcc Requirements
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using the AT&T U-verse TV Point Anywhere RF Remote Control. Note: This equipment has been tested and found to comply designed with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. - Page 24 FCC Requirements (continued) 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio / TV technician for help. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
-
Page 25: Customer Service Information
For a Spanish version of this manual visit: www.helpme.att.net/controlremoto One (1) Year Warranty AT&T guarantees from one (1) year of purchase this AT&T U-verse TV Point Anywhere RF Remote Control will properly perform its intended functions. This is a Limited Warranty that does not cover defects resulting from misuse, abuse, accident or negligence, including any failure to follow the instructions provided with the RF Remote Control. -
Page 26: Specifications & Notice
The AT&T U-verse TV Point Anywhere RF Remote Control is intended and sold for use only with AT&T's U-verse TV receivers. May not be compatible with all entertainment systems or capable of accepting every programming code for other devices.
Need help?
Do you have a question about the U-verse and is the answer not in the manual?
Questions and answers
New S30-S1B only turns tv on/off & volume up/dn. Will do nothing else!