Table of Contents
Advertisement
22.1.3 TX Delay Time
TX Delay Time is a duration between the time when the
transmission ends due to the expiration of the TX Interval
Time, the changing channel, or the deactivation of the
CW ID Override function and the time when TKR-750/
850/751/851 resumes transmitting in order to send the
CW ID. TKR-750/850/751/851 sends the CW ID after the
CW Mod. Delay Time expires.
Delay Time (CW ID).)
Note: TX Delay Time function is not applicable when sending the
CW ID with the CW ID On function.
! Configuration of KPG-91D
" Configuring the TX Delay Time (Refer to FPRG
6.3.3 TX Delay Time.)
22.1.4 CW Speed (CW ID)
CW Speed is a speed in WPM (word per minute) to send
the CW ID.
! Configuration of KPG-91D
" Configuring the CW Speed (Refer to FPRG 6.3.4
CW Speed.)
22.1.5 CW Mod. Delay Time (CW ID)
CW Mod. Delay Time is a duration between the time
when the TKR-750/850/751/851 starts transmitting and it
sends the CW ID.
! Configuration of KPG-91D
" Configuring the CW Mod. Delay Time (Refer to
FPRG 6.3.5 CW Mod. Delay Time.)
22.1.6 Audio Frequency (CW ID)
Audio Frequency is a CW Tone frequency to send the CW
ID. The CW Tone frequency can be configured within 400
Hz and 2000 Hz.
! Configuration of KPG-91D
" Configuring the Audio Frequency (Refer to FPRG
6.3.6 Audio Frequency.)
22.1.7 TX Required in Interval
TX Required in Interval is used to send a CW ID with the
configured interval when TKR-750/850/751/851 tries to
transmit during the TX Interval Time.
Interval Time.)
Version: 1.01 USA
(Refer to 22.1.5 CW Mod.
(Refer to 22.1.2 TX
Function Reference (FUNC)
Note: The TX Required in Interval function is not applicable when
sending the CW ID with the CW ID On function since you
can only configure the interval with this function.
! Configuration of KPG-91D
" Configuring the TX Required in Interval (Refer to
FPRG 6.3.7 TX Required in Interval.)
22.1.8 CW ID Override
CW ID Override function is used to send a CW ID with the
audio signal when the TX Interval Time expires during the
transmission.
Note:
# When sending the CW ID configured with CW ID Override On,
the QT/DQT code configured to the channel is encoded
regardless of the Encode with QT/DQT configuration.
22.1.11 Encode with QT/DQT (CW ID).)
# TKR-750/850/751/851 does not send the CW ID even when the
CW ID On function is enabled during transmission while the CW
ID Override function is disabled.
! Configuration of KPG-91D
" Configuring the CW ID Override function (Refer to
FPRG 6.3.8 CW ID Override.)
22.1.9 Send CW ID to RA
Send CW ID to RA is used to monitor the CW ID sounds
when sending the CW ID from TKR-750/850/751/851, the
RA line, and the front speaker. TKR-750/850/751/851
transmits the audio signals with the CW ID during the
reception.
Note: The CW ID is only sent to RA line when the channel is in
Simplex mode. In this case, the CW ID is not sent to the
speaker.
! Configuration of KPG-91D
" Configuring the Send CW ID to RA (Refer to FPRG
6.3.9 Send CW ID to RA.)
22.1.10CW ID on Channel change
CW ID on Channel Change is used to send a CW ID
when the channel is selected or changed. TKR-750/850/
751/851 sends the CW ID regardless of the configuration
of the CW Mod. Delay Time and the TX Interval Time.
! Configuration of KPG-91D
" Configuring the CW ID on Channel Change (Refer
to FPRG 6.3.1 CW ID on Channel change.)
22 CW ID/CW MESSAGE
(Refer to
54
Advertisement
Table of Contents
