Clay Paky A.LEDA WASH K5 Instruction Manual
  1. Manuals
  2. Brands
  3. Clay Paky Manuals
  4. Flood Light
  5. A.LEDA WASH K5
  6. Instruction manual

Clay Paky A.LEDA WASH K5 Instruction Manual

Hide thumbs Also See for A.LEDA WASH K5:
Table of Contents

Advertisement

Quick Links

Download this manual
INDEX
Page
Contents
2
Safety information
3
Unpacking and preparation
4
Installation and start-up
5
Control panel
7
Menu setting
14
Maintenance
16
Optional accessories
19
Technical information
19
Cause and solution of problems
20
Channel functions
A LEDA WASH K5
A LEDA WASH K10
A LEDA WASH K20
INSTRUCTION MANUAL
Congratulations on choosing a Clay Paky product
We thank you for your custom.
Please note that this product, as all the others in the rich Clay
Paky range, has been designed and made with total quality to
ensure excellent performance and best meet your expectations
and requirements.
Carefully read this instruction manual in its entirety and keep it
safe for future reference. It is essential to know the information
and comply with the instructions given in this manual to ensure
the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting
or to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this
instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the
characteristics stated in this instruction manual at any time and
without prior notice.
1
C61401
C61405
C61410

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the A.LEDA WASH K5 and is the answer not in the manual?

Questions and answers

Related Manuals for Clay Paky A.LEDA WASH K5

Summary of Contents for Clay Paky A.LEDA WASH K5

  • Page 1 Menu setting CLAY PAKY S.p.A. disclaims all liability for damage to the fitting Maintenance or to other property or persons deriving from installation, use and...

  • Page 2: Safety Information

    SAFETY INFORMATION • Installation Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible.

  • Page 3: Unpacking And Preparation

    UNPACKING AND PREPARATION IST004/001 2 x 183102/805 Packing contents - Fig. 1 UNLOCKED LOCKED PAN Mechanism Lock and Release (every 90°) - Fig. 2 A LEDA WASH...

  • Page 4: Installation And Start-Up

    INSTALLATION AND START-UP Installing the projector - Fig. 3 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.

  • Page 5: Control Panel

    CONTROL PANEL Mains NB: connecting one “A.leda Wash K5” to the mains, it is possible to connect up to a maximum of 11 “A.leda Wash K5” in parallel at the same time. Connecting to the mains supply - Fig. 5 DMX 512 5 PIN SCREEN...
  • Page 6 Reversal of the display - Fig. 8 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512).

  • Page 7: Menu Setting

    MENU SETTING Invert System Set Up Option Pan / Tilt Information Address Errors Invert Channel Fixture Tilt Mode Hours Swap Pan-Tilt Fixture ID Energy Tot Encoder Pan-Tilt Ethernet System Interface Version P/T Homing mode Board Option Pan Home Diagnost. Def Pos Tilt Home Information Def Pos...
  • Page 8 NOTE: On grey the default options SET UP MENU DMX ADDRESS NOTE: without the DMX signal the Address (XXX) flashing Set Up Address xxx Allows you to select the DMX ADDRESS. Address 1) Press - the current DMX Adress appear on the display. 2) Use the UP and DOWN , RIGHT...
  • Page 9 OPTIONS MENU PAN / TILT Invert pan Invert Option Pan / Tilt Used for reversing Pan movement. 1) Press - the current settings appear on the display (On or Off). 2) Use the UP and DOWN keys to enable (On) or disable (Off) PAN inversion.
  • Page 10 SILENT MODE Silent Option Standard mode It lets you select the “Silent Mode” from the two available. 1) Press the current setting appears on the display. 2) Use the UP and DOWN keys to select one of the following Quiet settings: Standard: Maximum speed and consequently maximum effects noise level.

  • Page 11: Information Menu

    SETTING Default Reset To Option Setting Used to save 3 different settings of the items in the options menu and Preset Dafault relative submenus. Go Back 1) Press - “Default preset” appears on the display. 2) Use the UP and DOWN keys to select one of the following User Load...

  • Page 12: Manual Control

    SYSTEM VERSION System Board Revis. Hw.rv. Information Version CPU brd x.x.x Used for displaying the software and hardware version of each board com.dev installed in the projector. 0: PT-3f 1: Ld - Kxx CPU brd (CPU board) 0: PT-3f (Scheda Pan / Tilt) 1: Ld - Kxx (Scheda LED) BOARD DIAGNOSTIC Board...
  • Page 13 ADVANCED MENU To enable the "Advanced Menu" set up the "Access code" (1234) using the Code Advanced , DOWN , RIGHT keys. 1234 Press - "Menu advanced" appears on the display UP LOAD FIRMWARE Transfer the firmware on all the connected fixtures ? Upload Allows you to transfer the firmware from 1 fixture to all the connected fixtures.
  • Page 14 Battery removal - Fig. 9 This product contains a rechargeable lead-acid battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. LiFePO4 A LEDA WASH...

  • Page 15: Maintenance

    MAINTENANCE Opening the covers - Fig. 10 Removing/Assembling the lens unit - Fig. 11 NB: Apply Loctite 222 (p/n COL002) to the threads of the 3 screws (1) before tightening them. A torque of 0.3N is recommended in order to avoid damaging the zoom movement actuators.
  • Page 16 DIM002/001 Replacing the line actuator - Fig. 12 NB: It is highly recommended to use the DIM002/001 (1) template whenever it is necessary to replace one of the three Zoom movement line actuators. DIM002/001 ensures the actuator group is centred correctly on the lens plate before tightening the 2 screws (2) that fasten the actuator in place. A LEDA WASH...

  • Page 17: Optional Accessories

    OPTIONAL ACCESSORIES A.LEDA WASH K5 C61452 C61453 Cover - Fig. 13 C61452 - Transparent cover C61453 - Frosted cover C61451 Transparent mask - Fig. 14 Continue A LEDA WASH...
  • Page 18 A.LEDA WASH K10 C61455 C61456 Cover - Fig. 15 C61455 - Transparent cover C61456 - Frosted cover C61454 Transparent mask - Fig. 16 A LEDA WASH...
  • Page 19 A.LEDA WASH K20 C61458 C61459 Cover - Fig. 17 C61458 - Transparent cove C61459 - Frosted cover C61457 Transparent mask - Fig. 18 Continue A LEDA WASH...

  • Page 20: Technical Information

    • K20 - 750VA • K10 - 450VA (9.65") • K5 - 170VA (14.72") Max 1800VA (with 11 A.leda Wash K5 connected in parallel) Total output K5 - Max 2100 lumens K10 - Max 5500 lumens K20 - Max 10500 lumens (15.00")

  • Page 21: Channel Functions

    CHANNEL FUNCTION A.LEDA WASH K5 STANDARD SHAPES EXTENDED EXTENDED RGBW CHAN- CHAN- CHAN- CHAN- CHANNEL MODE CHANNEL MODE CHANNEL MODE CHANNEL MODE Red fine Red fine Red fine Red fine Green Green Green Green Green fine Green fine Green fine...
  • Page 22 A.LEDA WASH K10 STANDARD SHAPES EXTENDED EXTENDED RGBW CHAN- CHAN- CHAN- CHAN- CHANNEL MODE CHANNEL MODE CHANNEL MODE CHANNEL MODE Red fine Red fine Red fine Red fine Green Green Green Green Green fine Green fine Green fine Green fine Blue Blue Blue...
  • Page 23 A.LEDA WASH K20 STANDARD SHAPES EXTENDED EXTENDED RGBW CHAN- CHAN- CHAN- CHAN- CHANNEL MODE CHANNEL MODE CHANNEL MODE CHANNEL MODE Red fine Red fine Red fine Red fine Green Green Green Green Green fine Green fine Green fine Green fine Blue Blue Blue...
  • Page 24 NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the Home position (Pan bit 128 - Tilt bit 128) all the others channels stay @ bit 0. • RED • MACRO COLOUR GREEN BLUE BIT VALUE...
  • Page 25 • STOP STROBE • PAN FINE Operation with option InvertPan (Tilt conventionally represented at 14% and option Invert Tilt Off) EFFECT 252 - 255 OPEN 239 - 251 RANDOM FAST STROBE 226 - 238 RANDOM MEDIUM STROBE RANDOM SLOW STROBE 213 - 225 208 - 212 OPEN...
  • Page 26 • RESET • TILT FINE Operation with option InvertPan EFFECT (Tilt conventionally represented at 14% and option Invert Tilt Off) COMPLETE RESET Complete reset is activated passing throug the unused range and staying 5 seconds in complete reset levels COMPLETE RESET PAN / TILT RESET Pan / Tilt reset is activated passing throug the unused range and staying 5 seconds in Pan / Tilt reset levels...
  • Page 27 SHAPE SELECTION - SHAPE SPEED - SHAPE OFFSET SHAPE Random MACRO NAME DESCRIPTION SHAPE SPEED SHAPE OFFSET SELECTION colors *1 N.a. N.a. N.a. Macro OFF Ring 1 Static effects. N.a. N.a. N.a. Ring 2 The ring or rings Ring 3 used by the Ring 4 macro are tur-...
  • Page 28 Macro Off DMX channel value: from 0 to 7. No shape effects activated. Turns off any previously selected shape. Static Rings DMX channel value: from 8 to 14. The ring or rings used by the macro are turned on with the foreground colour (Shape Red+Shape Green+Shape blue+Shape White). Avaliable combinations: Ring 1 On, Ring 2 On, Ring 3 On (Aleda K10, K20 only), Ring 4 On (Aleda K20 only),Ring 1+2 On, Ring 1+3 On (Aleda K10, K20 only), Ring 1+4 On (Aleda K20 only).
  • Page 29 • SHAPE FADE EFFECT 246-255 Smooth, fading curve with automatic gamma * Smooth, fading curve gamma 2 Smooth, fading curve gamma 1,986 Smooth, fading curve gamma 1,993 Smooth, fading curve gamma 0,513 Smooth, fading curve gamma 0,506 Smooth, fading curve gamma 0,5 0-15 Snap •...
  • Page 30 A.LEDA WASH K5 A.LEDA WASH K10 LED reference number for pixel mapping LED reference number for pixel mapping TILT: channel 16@ bit 200 TILT: channel 16 @ bit 200 A.LEDA WASH K20 LED reference number for pixel mapping TILT: channel 16 @ bit 200...
  • Page 31 A LEDA WASH...
  • Page 32 CLAY PAKY - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.it S.p.A.

This manual is also suitable for:

A.leda wash k10A.leda wash k20

Table of Contents