Overhead door OverDrive User Manual
  1. Manuals
  2. Brands
  3. Overhead door Manuals
  4. Garage Door Opener
  5. OverDrive
  6. User manual
Overhead door OverDrive User Manual

Overhead door OverDrive User Manual

Complete with codedodger remote control and series ii electronics
Hide thumbs
Table of Contents

Advertisement

Quick Links

TABLE OF CONTENTS

SECTION
PRE-INSTALLATION CHECKLIST . . . . . . . . . . . . . . . . . . . 2-3
PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
OPERATOR ASSEMBLY & INSTALLATION . . . . . . . . . . . 8-16
OPERATOR ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
OPERATOR INSTALLATION. . . . . . . . . . . . . . . . . . . . . 12-16
®
SYSTEM INSTALLATION. . . . . . . . . . . 17-18
WALL CONTROL INSTALLATION . . . . . . . . . . . . . . . . . . . . . . 19
CONNECTING POWER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
FORCE ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
LIMIT SWITCH ADJUSTMENT. . . . . . . . . . . . . . . . . . . . . . 22
CONTACT REVERSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
WIRELESS CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-26
BATTERY / VISOR CLIP INSTALLATION . . . . . . . . . . . . . 23
PROGRAMMING REMOTE CONTROLS . . . . . . . . . 23-24
WIRELESS KEYPAD INSTALLATION . . . . . . . . . . . . . . . . . 24
PROGRAMMING WIRELESS KEYPAD . . . . . . . . . . . 25-26
OPERATING SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . 26
OPERATIONAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . 27
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-30
PERIODIC MAINTENANCE . . . . . . . . . . . . . . . . . . . . . 27-28
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . 28-29
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A
SERVICE INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
The Genuine. The Original.
Complete
with
PAGE
Remote Control
and
SERIES II Electronics
Included Wall Control MUST be installed prior
to Operation of this Garage Door Operator.
Safe-T-Beam
be Installed and the Force Controls Must be
Properly Set to close door.
This Equipment meets or exceeds all Federal,
State and UL 325 Safety Requirements.
*
Will not operate twice as fast
on a one-piece door.
NEED HELP?
Please call us if you are having difficulty, for any reason.
We would like to help you.
Call: 1.800.929.3667
Web: www.overheaddoor.com
®
Safety Reverse System Must
3505735581

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OverDrive and is the answer not in the manual?

Questions and answers

Related Manuals for Overhead door OverDrive

Summary of Contents for Overhead door OverDrive

  • Page 1: Table Of Contents

    The Genuine. The Original. Complete with TABLE OF CONTENTS SECTION PAGE Remote Control PRE-INSTALLATION CHECKLIST ....2-3 PARTS IDENTIFICATION ......4-6 SAFETY INFORMATION &...

  • Page 2: Pre-Installation Checklist

    PRE-INSTALLATION CHECK LIST FOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM Things to consider if you are planning to “do-it-yourself.” In many cases you will be replacing an existing door operator with a new one. However, if this will be the first operator installed there are some pre-installation issues which need to be addressed.
  • Page 3 TYPICAL SECTIONAL DOOR INSTALLATION TYPICAL ADDED SUPPORT HEADER BRACKET BRACKET MOUNTING BOARD BRACES 36” POWER CORD 120V GROUNDED OUTLET EXTENSION SPRING TORSION SPRING SAFE-T-BEAM ® TYPICAL (TRACKLESS) 1-PIECE DOOR INSTALLATION TYPICAL (TRACK GUIDED) 1-PIECE DOOR INSTALLATION ONE-PIECE DOOR SECTIONAL DOOR...

  • Page 4: Parts Identification

    PARTS IDENTIFICATION FOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM PQRS WXYZ NUSTBSENDSENS-1 NOTE: Accessories vary by Model . FASTENERS - Shown Full Size. See Parts List for description. 1/4"-20 Shoulder Bolt Clevis Pin #10-16 x 1-1/4" Phillips Hex Head Screw Cotter Pin 1/4"-20 Nut Wire Clip Rubber Bumper 3/8"-16 x 7/8"...
  • Page 5 1-PIECE BOOM HARDWARE EXPLODED VIEW “PRO” ONLY [ 3 ] NOTE: The Operator will not function unless the Safe-T-Beam ® System is installed and the Force Controls are properly set. Assembly for 10' or 12' door includes: 1. Special “Close” Limit Switch with longer wires.
  • Page 6 PARTS LIST POWER HEAD EXPLODED VIEW [ 1 ] Item Part Name Parts Required 1 Power Head Assembly (main carton) 2 1/4"-20 Hex Head Shoulder Bolt (blue bag) 3 Boom Assembly (1 piece)(packaged separately) 8 1/4"-20 Hex Serrated Flange Nut (blue bag) 11 5/16"-18 Hex Serrated Flange Nut (blue &...

  • Page 7: Safety Information & Safety Features

    SAFETY INFORMATION OPERATOR INSTALLATION IMPORTANT OVERVIEW OF INSTALLATION POTENTIAL HAZARDS INSTRUCTIONS Garage Doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of WARNING others depend on you reading the information in this manual.

  • Page 8: Operator Assembly & Installation

    OPERATOR ASSEMBLY & INSTALLATION FOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM Record your Model Number and Serial Number now on page 11 in the center of this manual. OPERATOR ASSEMBLY OPEN BLUE PARTS BAG NOTE: 3 piece operator assembly is for doors up to 7 feet 6 inches high.
  • Page 9 CAUTION Drive screw section and boom liner can slide out of boom sections. Keep boom sections level until operator is fully assembled 3. On 1 piece boom assembly go to step 11. 4. Arrange arrows on boom sections (Fig. 1-4). •...
  • Page 10 9. Install carriage and carriage stop (Fig. 1-9). • Slide carriage stop into railand along the length Release position of the rail to the power head. • Point arrow on side of carriage toward door. Engaged position • Place carriage lever in release position. •...
  • Page 11 14. Bundle excess limit switch wires (Fig. 1-13). • Leave just enough wire to easily reach the terminals on back of power head. • Hold the ends of the wires out beyond the back of the power head as you flip the unit upside-down again.

  • Page 12: Operator Installation

    OPERATOR INSTALLATION TRACK GUIDED WHAT TYPE OF DOOR DO YOU HAVE? Look at the photos on the right. Door type determines Track which of the remaining installation steps apply to you. NOTE: Will Not Operate twice as fast on a one-piece door.
  • Page 13 FOR TRACKLESS DOORS Centerline (“C”) 2. Find center of door and header (Fig. 1-21). • Close door. • Measure door width. – Mark a vertical line (“C”) in the center on the inside door and header. 3. Find header bracket position. Fig.
  • Page 14 5. Attach boom at header bracket (Fig. 1-25). • Place threaded end of boom strap through hole on header bracket. • Finger tighten nut [11] on threads. [ 11 ] 5/16"-18 Flange Nut Fig. 1-25 finger tight 6. Find power head position. •...
  • Page 15 FOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM OPEN BEAM CEILING Fig. 1-29 Mounting Methods Perforated Angle Iron Mounting Straps [30] [30] [11] [11] [55] [55] FINISHED CEILING NOTE: Materials may vary. NOTE: Read all instructions completely. Locate the ceiling joists or Garage constructions differ, so it may be trusses using a stud finder required to supply extra material and or similar device.

  • Page 16: Safe-T-Beam ® System Installation

    ® SAFE-T-BEAM SYSTEM INSTALLATION FOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM WARNING There should be no electrical power to the operator while installing Safe-T-Beam System wires. If you ® have plugged in the power cord–UNPLUG IT NOW. NOTE: Operator will not close door automatically unless the Safe-T-Beam System is installed.
  • Page 17 OPEN YELLOW PARTS BAG SECTIONAL 12. Install door arms (Fig. 1-32). FOR SECTIONAL DOORS – Attach straight arm to carriage. As short as – Secure with clevis [32] and cotter pin [33]. possible – Attach curved arm to door bracket. –...
  • Page 18 3. Wiring (cont’). • Securely fasten wires to wall as you go. – Use insulated staples (included). ≈ 1/2" [ 38 ] ≈ 1-1/4" to 1-1/2" FIG. 2-6 Splitting and stripping – Staples should be snug only. CAUTION Staples which are too tight can cut or pinch wires. Cut or pinched wires can cause the “STB”...

  • Page 19: Wall Control Installation

    WALL CONTROL INSTALLATION FOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM WHITE WIRE WARNING Verify there is no power to the operator before STRIPED installing wall control wires. CAUTION Use of any wall control other than the type supplied will prevent the light from working and could cause the door to operate on its own.

  • Page 20: Connecting Power

    CONNECTING POWER FOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM WARNING Safe-T-Beam ® Alignment Check To reduce the risk of electrical shock, this equipment has a grounding type plug that has a After turning the electrical power on, if the third (grounding) pin. This plug will only fit into a STB’s are not in proper alignment, the red grounding type outlet.

  • Page 21: Settings

    SETTINGS FOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM COARSE LIMIT SWITCH SET “CLOSE” LIMIT SWITCH—DOOR FULLY CLOSED 1. Setting “CLOSE” limit switch. • Check carriage disengaged. • With door fully closed, slide “CLOSE” limit switch until it is aligned with the carriage magnet. (Fig. 5- MAGNETS •...

  • Page 22: Force Adjustment

    CONTACT REVERSE FORCE ADJUSTMENT Limit switch adjustments must be completed WARNING before checking contact reverse. Door opens rapidly. 1. Check contact reverse. • Keep path clear. • Position ladder to the side of power head so • Open door using wall control. it is clear of all moving parts of operator •...

  • Page 23: Wireless Controls

    WIRELESS CONTROLS FOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM BATTERY / VISOR CLIP INSTALLATION 1. Install / replace battery (Fig. 6-1). • Using a pen or similar object, gently push in on tab. • Cover snaps open. Remove old battery. • Observe polarity markings (+,-) inside battery compartment.

  • Page 24: Wireless Keypad Installation

    3. Operate remote control. WIRELESS KEYPAD INSTALLATION • Point remote control at door. • Press button on remote control. NOT INCLUDED WITH ALL MODELS – Door moves. 1. Remove covers (Fig. 6-4). • Press button again. • Slide keypad cover up and remove. –...

  • Page 25: Programming Wireless Keypad

    4. Programming a second PIN PROGRAMMING WIRELESS KEYPAD • Open keypad cover fully–LED blinks one time (Fig. 6-6). CAUTION • Enter “1-5-9.” • Press “PROG”–LED blinks one time per second. Moving door can cause serious injury or death. • Enter desired PIN (up to 8 digits). •...

  • Page 26: Operating Safety Instructions

    7. Changing PIN (Fig. 6-5). • Open cover fully–LED blinks 1 time and IMPORTANT goes out. • Enter PIN you want to change. SAFETY INSTRUCTIONS • Press “PROG”–LED blinks 1 time and goes out. • Enter new PIN (up to 8 digits). •...

  • Page 27: Operational Features

    OPERATIONAL FEATURES FOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM ® INTELLICODE Access Security System. • Improves security of door operator by continuously changing the access code each Security time the remote control is used. Vacation • The door operator responds to each new code Switch only once.

  • Page 28: Troubleshooting Guide

    MAINTENANCE cont’ ..FOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM YEARLY Drive Screw CAUTION • Lubricate drive screw. Use only GLU4 lubricant, because other – Use GLU4 lubricant. lubricants may damage operator. TROUBLESHOOTING GUIDE SELF-DIAGNOSTIC TROUBLESHOOTING SOURCE ( RED LED ) SENSOR ( GREEN LED ) INDICATED CONDITION REQUIRED ACTION NORMAL OPERATION NONE REQUIRED...
  • Page 29 TROUBLESHOOTING GUIDE FOR HELP-1.800.929.3667 OR OVERHEADDOOR.COM CAUTION Use wall control supplied with operator. Any other Lights will • Disconnect and reconnect wires on wall control. Page 19. wall control can cause the operator to operate not go out. • Check wiring. •...

  • Page 30: Maintenance

    OPEN LIMIT MOTOR GREEN CLOSE LIMIT LIMITED WARRANTY Overhead Door Corporation (“ODC”) warrants to the original purchaser of the garage door opener as follows: THERE IS NO WARRANTY OF MERCHANTABILITY, Model 990 - Motor Lifetime* and all other parts 5 years.

  • Page 31: Accessories

    Mini télécommande à 2 fonctions avecCodeDodger 3-Function Wall Console with CodeDodger Consola de pared de 3 funciones con CodeDodger Console murale à trois fonctions avec CodeDodger OverHead Door Corp 22790 Lake Park Blvd. Alliance, Ohio 44601 Call: 1.800.929.3667 Web: www.overheaddoor.com...

Table of Contents

Save PDF