Page 2
Read this manual prior to initial operation of the product! Dear Customer, We hope that your product, which has been manufactured in modern facilities and passed through a strict quality control procedure, will give you very good results. We advise you to read through this manual carefully before using your product and keep it for future reference.
Important safety information This section includes safety information or adaptors to connect the dryer to that will help protection from risks of power supply in order to decrease the personal injuries or materialistic damages. risk of electric shock. Failure to follow these instructions •...
• This product must be grounded. Turn off the machine, turn off and Grounding installation decreases the contact an authorised service agent. risk of electric shock by opening a path • Do not stop the dryer before the drying with low resistance for the electricity cycle comes to an end unless you will flow in case of a malfunction or failure.
Children’s safety • Electrical appliances are dangerous for the children. Keep children away from the machine when it is operating. Do not let them tamper with the machine. • Packaging materials are dangerous to children. Keep the packaging materials out of reach of children or dispose them by classifying according to waste directives.
Installation Refer to the nearest Authorised Service Agent for installation of your product. C Preparation of location and electrical installation for the product is under customer’s responsibility. BInstallation and electrical connections must be carried out by a qualified personnel. A Prior to installation, visually check if the product has any defects on it.
periodically draining the water collected in CNever unscrew the adjustable feet from the water tank. their housings. Connecting the water drain hose; Electrical connection Connect the machine to a grounded outlet protected by a fuse of suitable capacity as stated in the technical specifications table. Our company shall not be liable for any damages that will arise when the machine is used on a circuit without grounding.
Transportation of the machine 1. Unplug the machine from the mains. 2. Remove the water drain (if any) and chimney connections. 3. Drain water remained in the machine completely before transportation. Disposing of the old machine Dispose of your old machine in an environmentally friendly manner.
Initial preparations for drying Things to be done for energy A B C saving: • Make sure that you operate the product at its full capacity but pay attention to not exceeding it. • Spin your laundry at the highest speed possible when washing them.
alcohol, fuel oil, kerosene, stain remover, Consider the information in the turpentine, paraffin and paraffin removers "Programme Selection Table". Always start must be washed in hot water with plenty of the programme in accordance with the detergent before being dried in the dryer. maximum load capacity.
Loading the laundry 1. Open the loading door. 2. Place the laundry in the machine without compressing. 3. Push the loading door to close. Ensure that no items are caught in the door. 11 EN...
Selecting a Programme and Operating Your Machine Control panel Jeans Daily Shirts Xpress 35 Iron Dry Synthetics Wool Cupboard Refresh Spin / Time Iron Dry Cupboard Start/Pause Sport Cottons Babycare Extra Dry Time Delay On / Off Delicates Freshen Up Cancel Press &...
this programme. •Shirt •Timer programs This programme dries the shirts more sensitively and creases them less and thus, helps to iron them more easily. C There may be a little humidity on your shirts at the end of the programme. We recommend you not to leave the shirts in the dryer.
Auxiliary function Changing the contrast Audio Warning Contrast can be adjusted in order to make the symbols on the display appear clearer. It may particularly be necessary to change the contrast setting of the display Cancel Audio warning Audio warning Audio warning audio warning level 1...
Warning symbol turns on with certain set the desired time delay. intervals to remind that the condenser 3. Press “Start/Pause/Cancel” button. The needs cleaning. Time delay symbol lights up. Pause Door open symbol fades. Start symbol lights up. 4. The “:” in the middle of the displayed time delay will start flashing.
C Anti-creasing icon will light up at the Therefore, it is recommended to add end of the programme if anti-creasing laundry before the drying programme function is active. has started. C If you select a new programme by Changing the programme after the turning the programme selection knob programme has started while your machine is in standby,...
Ending the programme through canceling A new program can be selected and started after “Program cancel” is activated in order to change the drying program. To cancel any selected programme: Press “Start/Pause/Cancel” button for about 3 seconds. “Lint filter cleaning” and “Water tank”...
Maintenance and cleaning Filter Cartridge / Door Inner Surface Lint and fibres released from the laundry to the air during the drying cycle are collected in the “Filter Cartridge”. Sensor C Such fibre and lint are generally formed during wearing and washing. C Always clean the filter and the inner surfaces of the cover after each drying process.
Water tank; drying cycles or once a month. To clean the condenser: The moisture in the damp laundry is taken 1. If a drying process has been carried out, from the laundry and condens ed. Drain open the door of the machine and wait the water tank after each drying cycle or until it cools down.
Page 22
4. Clean the condenser by applying pressurized water with a shower armature and wait until the water drains. 5. Place the condenser in its housing. Fasten the 2 locks and make sure that they are seated securely. 6. Close the kick plate cover. 22 EN...
Suggested solutions for problems Drying process takes too much time • Meshes of the filter may be clogged. Wash with water. Laundry comes out wet at the end of drying. • Meshes of the filter may be clogged. Wash with water. •...
Page 24
“Condenser cleaning” symbol is on. • Filter drawer/Condenser might have not been cleaned. Clean the filters in the condenser/filter drawer under the kick plate. A Call an authorised service if the problem persists. 24 EN...
Need help?
Do you have a question about the DCU 7330 X and is the answer not in the manual?
Questions and answers