Related Manuals for Husqvarna 326HD60
Summary of Contents for Husqvarna 326HD60
- Page 1 Operator's manual (CARB II, EPA II) 326HD60 326HD75 Please read these instructions carefully and make sure you understand them before using the machine. X-series X-series English...
-
Page 2: Symbols
SYMBOL EXPLANATION Symbols WARNING! The hedge trimmer can be dangerous! Careless or incorrect use can result in serious, even fatal injury. Read through the Operator‘s Manual carefully and understand the content before using the hedge trimmer. Always use • Ear protection •... -
Page 3: Table Of Contents
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual. -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS Personal protective eqipment IMPORTANT INFORMATION • Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand this manual. - Page 5 SAFETY INSTRUCTIONS 4. Vibration damping system The hedge trimmer is equipped with a vibration damping system, which is designed to give as vibra- tion-free and comfortable use as possible. The hedge trimmer’s vibration damping system reduces the transfer of vibrations between the engine unit/blades and the hedge trimmer’s handles.
-
Page 6: Control, Maintenance And Service Of The Hedge Trimmer's Protective Equipment
Control, maintenance and service of the hedge trimmer’s protective equipment IMPORTANT INFORMATION • All service and repairs to the machine require special training. • This applies especially to the machine‘s safety equipment. If the machine does not meet any of he controls listed below you should contact your service workshop. - Page 7 • Check that the blade guard is not damaged or distorted. • Replace the blade guard if it is bent or damaged. 8. Gearbox • The gearbox gets hot when the hedge trimmer is in use. To avoid burning yourself do not touch the gearbox. English –...
-
Page 8: General Safety Instructions
Contact your local petrol station to find out how to dispose of excess fuel. • The blades transport guard should always be fitted when transporting or storing the hedge trimmer. WARNING! Exercise great care when handling fuel. -
Page 9: General Working Instructions For Hedge Trimmer
Safety instructions when using the hedge trimmer WARNING! The hedge trimmer can cause serious personal injury. Read the safety instructions carefully. Learn how to use the machine. WARNING! Cutting tool. Do not touch the tool without first switching off the engine. -
Page 10: Basic Working Techniques
• Only use original spare parts when carrying out repairs. Basic working techniques • The hedge trimmer’s rear handle can be set in three positions by pulling out the catch. See figure. When the handle is adjusted the hedge trimmer should be idling or not running. -
Page 11: What Is What
What is what on the hedge trimmer? 1. Operator’s Manual 2. Grease filler cap 3. Gearbox 4. Blades 5. Blade guard 6. Loop handle 7. Cylinder cover 8. Starter handle 9. Stop switch 10. Throttle trigger lock 11. Adjustable handle 12. -
Page 12: Fuel Handling
Two-stroke oil • For the best results use HUSQVARNA two-stroke oil, which has been specially developed for HUSQVARNA’s small, two-stroke engines. Mixing ratio 1:50 (2%). • Never use two-stroke oil intended for water cooled outboard motors, so-called outboard motor oil. -
Page 13: Start And Stop
Always move the hedge trimmer about 3 metres from the filling position before starting. Place the machine on a flat surface. Bear in mind that the blades start to move when the engine is started. -
Page 14: Maintenance
Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. To ensure that your unit is at peak performance and... -
Page 15: Muffler
Muffler NOTE! Some mufflers are fitted with a catalytic converter. See “Technical data” to see whether you clearing saw is fitted with a catalytic converter. The muffler is designed to dampen the noise level and to direct the exhaust fumes away from the user. -
Page 16: Air Filter
Therefore it is necessary to replace the filter from time to time with a new filter. A damaged air filter must always be replaced. Oiling the air filter Always use HUSQVARNA filter oil, order no. 503 47 73-01. The filter oil contains a solvent to make it spread evenly through the filter. -
Page 17: Maintenance Schedule
Maintenance schedule Below you will find some general maintenance instructions. Daily maintenance • Check throttle trigger and throttle trigger lockout function. • Check stop switch function. • Check that the blades do not rotate while idling or when the choke is in the start position. •... -
Page 18: Technical Data
Note 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. – English TECHNICAL DATA 326HD60 326HD75 1,55/25,4 1,55/25,4... -
Page 19: Your Warranty Rights And Obligations
REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest &... - Page 20 – English...
- Page 21 English –...
- Page 22 ´+H!Q¶3r¨...
- Page 23 English –...
- Page 24 114 00 14-93 ´+H!Q¶3r¨ 2002W02...