Related Manuals for RTI XP-3
Summary of Contents for RTI XP-3
- Page 1 It’s Under Control ® It’s Under Control ® XP-3 Remote Control Processor 70-210093-22 V1.0...
- Page 2 XP-3 Remote Control Processor Copyright © 2011 Remote Technologies Incorporated All rights reserved.
-
Page 3: Federal Communications Commission Notice
This device must accept any interference received including interference that may cause undesired operation. FCC ID: MMURTI1900 IC (Canada): 3166A-RTI1900 N27917 DECLARATION OF CONFORMITY (DOC) The Declaration of Conformity for this product can be found on the RTI website at: www.rticorp.com/declaration... -
Page 4: Safety Suggestions
XP-3 Remote Control Processor SAFETY SUGGESTIONS Read Instructions. Read all safety and operating instructions before operating the unit. Retain Instructions. Keep the safety and operating instructions for future reference. Heed Warnings. Adhere to all warnings on the unit and in the operating instructions. -
Page 5: Limited Warranty
Remote Technologies Incorporated’s liability for any defective product is limited to repair or replacement of the product, at our option. If your XP-3 Remote Control Processor needs service, please contact Remote Technologies Incorporated by telephone, fax or E-mail for return information. -
Page 6: Disclaimer
Microsoft Corporation in the United States and other countries. ZigBee is a registered trademark of the ZigBee Alliance. XP-3, Integration Designer, and the RTI logo are registered trademarks of Remote Technologies Incorporated. Other brands and their products are trademarks or registered trademarks... -
Page 7: Table Of Contents
Mounting ............... 13 Power ..............14 Connections (Antennas, IR, Modules, etc.) ....14 RS-232 Cabling/Pinouts ........... 16 Programming the XP-3 ..........17 Status LED reference ..........17 Setting the Zone Code ..........17 Connection Diagrams ..........18 Chapter 4 - Specifications ........... 21 Chapter 5 - Troubleshooting ........ - Page 8 XP-3 Remote Control Processor...
-
Page 9: Chapter 1 - Welcome
Avoid installing the XP-3 in a location where it can come in contact with direct sunlight. Do not let the XP-3 get wet. It should not be handled with wet hands or placed in an area where it could get wet. -
Page 10: Product Contents, Unpacking
• One (1) XP-3 Mounting Plate with screws UNPACKING AND INSPECTION After unpacking your new XP-3 Remote Control Processor, save all of the packing materials in case you ever have to ship the unit. Thoroughly inspect the XP-3 and packing materials for signs of damage. -
Page 11: Chapter 2 - Features
It’s Under Control ® CHAPTER 2 | FEATURES The XP-3 provides superior quality and reliability as well as these specific features: Powerful 32bit, 533MHz CPU. 128Mb of non-volatile Flash memory stores your system configuration even when power is not present. -
Page 12: Diagram
+12VDC - Port 1 = MPIO Power - Ports 2 & 3 = IR only Supply Relays (2) Sense inputs (2) NOTE: Sense input #1 can also be configured as an input for RTI RM-433 antennas or RTI in-wall controllers. -
Page 13: Chapter 3 - Installation And Operation
Communication Module are used, the distance limitation is usually 50 feet depending on baud rate. MOUNTING INSTRUCTIONS To mount the XP-3 to a wall, shelf, or cabinet you must use the enclosed mounting plate. • Level and anchor XP-3 mounting plate to desired wall, shelf, or cabinet by screwing appropriate wall, shelf, or cabinet fasteners (not included with the XP-3) through the mounting plate fastener holes. -
Page 14: Power
The included AC adapter should be connected to the POWER jack on the XP-3 or the 12VDC/Ground terminals (see below). The power LED will turn- on. Use only the supplied AC adapter to power the XP-3. Using a different power adapter could result in damage to the XP-3 or poor performance. - Page 15 The IR output gain can be separately adjusted for each of the three output ports. The XP-3 is shipped with the IR gain set to the optimum level for most equipment, and it should only need to be adjusted if the attached equipment is not responding reliably.
-
Page 16: Rs-232 Cabling/Pinouts
CHAPTER 3 | INSTALLATION AND OPERATION RELAYS The two relays in the XP-3 can provide contact closure or switching control for loads up to 5A/30VDC each. Both relays are Normally Open when not energized, but they can be programmed to behave Normally Closed as long as power is applied to the XP-3. -
Page 17: Programming The Xp-3
The LED will stay on while the XP-3 is busy processing the action associated with the trigger code. The status LED will illuminate red and stay red to indicate if the XP-3 is in firmware update mode. This process is described in the firmware update wizard. -
Page 18: Connection Diagrams
XP-3 Remote Control Processor CHAPTER 3 | INSTALLATION AND OPERATION CONNECTION OPTIONS The following diagram illustrates some of the XP-3 connection options. Single or Dual Emitters Power Direct IR Supply To Source Equipment Television, Receiver, Lighting Systems, etc. NOTE: Each IR output can drive up to two flashing IR emitters or three non-flashing IR emitters directly. - Page 19 It’s Under Control ® CHAPTER 3 | INSTALLATION AND OPERATION CONNECTION OPTIONS The following diagram illustrates some of the alternative XP-3 connection options. Power Supply Power Supply RTI RM-433 RTI Keypad RF Receiver Power Supply Note: RTI Keypad needs a...
- Page 20 XP-3 Remote Control Processor CHAPTER 3 | INSTALLATION AND OPERATION CONNECTION OPTIONS (CONTINUED) XP-3 connection examples: Relays RS-232 Control (cat5) Voltage Sense Inputs Voltage source wired to Sense In 1 or 2 and Ground RJ-45>DB-9 Adapter Lighting, security, media server or other supported two-...
-
Page 21: Chapter 4 - Specifications
CHAPTER 4 | SPECIFICATIONS Power Supply +12VDC, 1A Multi-Purpose Output One, custom 3.5mm 4-conductor jack, designed Port for RTI modules (Sense input/RS-232 output) as well as industry standard IR emitters. Infrared Output Two, 3.5mm jacks, compatible with industry Ports standard IR emitters... - Page 22 XP-3 Remote Control Processor...
-
Page 23: Chapter 5 - Troubleshooting
XP-3 USB PROGRAMMING PORT DOES NOT WORK Verify that your PC is using Windows XP or higher and have the RTI USB driver installed. If you do not have the driver installed, the RTI USB driver installation file can be found in the drivers folder in the Integration Designer program folder. - Page 24 XP-3 Remote Control Processor XP-3 ETHERNET PROGRAMMING DOES NOT WORK Check the Net Link LED on top of the XP-3 for link and activity status. LIGHT ON = Valid Link LIGHT BLINKS = Activity Check Integration Designer to verify network settings are correct...
-
Page 25: Chapter 6 - Service And Support
Fax (952) 253-3131 info@rticorp.com RTI TECHNICAL SUPPORT At RTI, customer service and satisfaction is an utmost priority. If you are encountering any problems or have a question about your RTI product, please contact RTI Technical Support for assistance. RTI provides technical support by telephone, fax or e-mail. For the highest quality service, please have the following information ready, or provide it in your fax or e-mail. - Page 26 SERVICE AND SUPPORT Shipment of XP-3 for Service RTI will pay all labor and material expenses for all repairs covered by this product’s warranty. If necessary repairs are not covered by warranty, or if a unit is examined which is not in need of repair, you may be charged for the repairs or examination.
-
Page 27: Index
Mounting/Power ............14 Programming ..............17 Limited Warranty ..............5 Product Contents .............. 10 Safety Suggestions ............. 4 Service and Support ............25 Contact RTI ..............25 Shipment for Service ............. 26 Technical Support ............25 Specifications ..............21 Troubleshooting ..............23... - Page 28 XP-3 Remote Control Processor It’s Under Control ® Remote Technologies Incorporated 5775 12th Avenue East, Suite 180 Shakopee, MN 55379 Tel: 952-253-3100 Fax: 952-253-3131 www.rticorp.com © 2011 Remote Technologies Inc. All rights reserved. Printed in Taiwan.
Need help?
Do you have a question about the XP-3 and is the answer not in the manual?
Questions and answers