DeWalt DW744 Instruction Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Saw
  5. DW744
  6. Instruction manual

DeWalt DW744 Instruction Manual

Table saw
Hide thumbs Also See for DW744:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
DW744-XE/387486-01
5/1/02
3:43 PM
Page 2

INSTRUCTION MANUAL

TABLE SAW
MODEL DW744

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DW744

Summary of Contents for DeWalt DW744

  • Page 1: Instruction Manual

    DW744-XE/387486-01 5/1/02 3:43 PM Page 2 INSTRUCTION MANUAL TABLE SAW MODEL DW744...
  • Page 2 DW744-XE/387486-01 5/1/02 3:43 PM Page 3...
  • Page 3 DW744-XE/387486-01 5/1/02 3:44 PM Page 4...
  • Page 4 DW744-XE/387486-01 5/1/02 3:44 PM Page 6...

  • Page 5: Safety Instructions

    DW744-XE/387486-01 5/1/02 3:44 PM Page 5 Safety Instructions 15 Remove adjusting keys and wrenches. Always check that adjusting keys and wrenches are removed from the tool before operating the tool. When using power tools, always observe the safety regulations applicable in your 16 Use appropriate tool.
  • Page 6 DW744-XE/387486-01 5/1/02 3:44 PM Page 8 Description Fig. 2 4. Rear pinion bearing assembly Additional Safety Rules for Table Saw Figure 2 shows all the loose items and 5. Saw shown upside down for clarity WARNING: For your own safety, do not operate your saw until it is completely hardware packed with the saw.

  • Page 7: Extension Cords

    DW744-XE/387486-01 5/1/02 3:44 PM Page 9 • IF YOU STALL OR JAM the saw blade in the workpiece, turn saw OFF, remove including all through sawing. the workpiece from the saw blade, and check to see if the saw blade is parallel to •...

  • Page 8: Specifications

    DW744-XE/387486-01 5/1/02 3:44 PM Page 12 Specifications ATTACHING/REPLACING THE BLADE 1. THE SAW MUST BE UNPLUGGED BEFORE YOU MAKE ANY Table Size: 19 1/4” (489 mm) x 26 1/2” (673 mm) ADJUSTMENT TO THE BLADE. Mitre Angle: 30º L&R 2. Raise the saw blade arbor to its maximum height by turning the blade height Bevel Angle: 0°...

  • Page 9: Connecting Saw To Power Source

    DW744-XE/387486-01 5/1/02 3:44 PM Page 13 blade guard as shown in Fig. 11, ensuring the bolts fit into the slots on the blade 1. Centre the saw on a square piece of 1/2” (12.7 mm) plywood. The plywood must guard. The top of the slots must rest on the bolts. The bottom edge of the splitter have a 15”...

  • Page 10: Saw Blades

    DW744-XE/387486-01 5/1/02 3:44 PM Page 14 RIP SCALE POINTER FENCE PARALLEL ADJUSTMENT NOTE: The rip scale pointer will need to be readjusted whenever a thicker or thinner 1. Unlock rail lock lever. blade is installed. 2. Locate rear pinion bearing and loosen the two hex bolts just enough to allow side-to-side movement.

  • Page 11: Operation

    DW744-XE/387486-01 5/1/02 3:44 PM Page 11 feed direction. During kickback, the workpiece could be thrown back at the operator. It 2. Bevel angle lock knob is tight. can also drag the operator’s hand back into the blade if the operator’s hand is at the 3.

  • Page 12: Ripping Small Pieces

    DW744-XE/387486-01 5/1/02 3:44 PM Page 10 WARNING: Before connecting the table saw to the power source or operating the Mitreing saw, always inspect the guard and splitter for proper alignment and clearance with saw This operation is the same as crosscutting except the mitre gauge is locked at an blade.

  • Page 13: Dust Collection

    DW744-XE/387486-01 5/1/02 3:44 PM Page 7 Dust Collection WALT After-Sales Service Your table saw is equipped with a dust shroud and dust collection port. For best All D WALT power tools are thoroughly tested before leaving the factory. However, if results, connect a vacuum to the port at the rear of the saw.
  • Page 14 DW744-XE/387486-01 5/1/02 3:42 PM Page 1 NOTE: THIS INSTRUCTION MANUAL IS APPLICABLE FOR THE FOLLOWING SUB-CODES: -XE Form# 387486-01 WALT INDUSTRIAL TOOL COMPANY COPYRIGHT © 1998, 1999 PART NO: 569544-00...

Table of Contents