Table of Contents
Advertisement
SAUNACORE
Installation Instructions FOR SAUNACORE KW SAUNA HEATING UNITS & CONTROLS
INSTALLATION
GUIDE &
OWNERS MANUAL
Saunacore Heaters
This Manual contains installation and operation instructions,
specifications, maintenance information, and warranty information
SAUNACORE
Technical Hotline 905-951-6662
www.saunacore.com
Advertisement
Table of Contents
Related Manuals for Saunacore Heaters
Summary of Contents for Saunacore Heaters
- Page 1 SAUNACORE INSTALLATION INSTRUCTIONS FOR SAUNACORE KW SAUNA HEATING UNITS & CONTROLS INSTALLATION GUIDE & OWNERS MANUAL Saunacore Heaters This Manual contains installation and operation instructions, specifications, maintenance information, and warranty information SAUNACORE Technical Hotline 905-951-6662 www.saunacore.com...
-
Page 2: Installation Instructions
Top View of SAUNACORE Heaters HEATING UNITS CORNER MOUNT SAUNACORE KW is installed in a corner of the Sauna room or on the straight wall by means of two mounting brackets (see illustration). The unit should be placed 2" inches (minimum) from the floor, and not closer than 45 inches to the ceiling. - Page 3 (applies to Canadian application) heater. Note: Warranty is void on Saunacore heaters and • Use only clean tap water on the sauna stones. Do not use controls if the installer or electrician fails to...
- Page 4 5 to 10 minutes and it may blink on-off to notify you that it is ready to shut down. Note: • All sauna heaters will automatically shut off in 30 minutes (may be set for 60 minutes). • If the sauna system is 600 volts, 450 volts, 380 volts, 240 volts, or 208 volts;...
- Page 5 Commander Controls Installation & Wiring Commander Controls Installation & Wiring Commander Controls Installation & Wiring Commander Controls Installation & Wiring SAUNACORE NACORE I\\\\\ UNACORE . For supply connections, use suitable AWG wires suitable for at least 90 C (190 F).
- Page 6 Commander Keypad Mounting Installation SAUNACORE Figure 5 5 Figure 6 6 Figure 7 7 Internal Commander Schematic...
- Page 7 SAUNACORE "MERCURI" Control Operating Instructions Display windows: Left Window “Minutes” Time Display Right Window “Degrees” Temperature Display Signaling LED’s: C - Temperature is displayed in deg C F - Temperature is displayed in deg F Heat - Flashing means heater is on...
- Page 8 Mercuri Digital Control SAUNACORE CAUTION: THE MANUAL RESET LIMIT SHALL BE WIRED IN THE CIRCUIT Figure 8 8 Mercuri Digital Controls (120v/240v 1Phase 30 Amps + Under) Eurpean Connection ( L2 = N - "Neutral") Power Supply For supply connections, use suitable...
- Page 9 Mercuri Digital Control SAUNACORE Mercuri control must be installed outside of the sauna room, into a 3 gang masonry electrical box. When a magnetic contactor is used, it also must be installed into an appropriate metal electrical enclosure box outside of the sauna.
- Page 10 Mechanical Controls—Wiring (wall or built-in) SAUNACORE CAUTION: THE MANUAL RESET LIMIT SHALL BE WIRED IN THE CIRCUIT. Figure 1 1 2 Mechanical Control Breaker Panel (120v/240v/1Phase 30 Amps and Under) European Connection ( L2 = N - "Neutral" ) For supply connections, use suitable...
- Page 11 Mechanical Controls—Wiring (wall or built-in) SAUNACORE Mechanical Control (240v/208v/1 or 3 Phase 50 Amps and over) (applies to Canadian application) Breaker Panel (Main Power Supply) Mercuri control must be installed outside of the sauna room, into a 3 gang masonry electrical box.
- Page 12 Commander Control For Emitters Power Supply SAUNACORE Figure 16 Note: All power supply wires from control box to stove European Connection must be protected by ( L2 = N - "Neutral" ) metal conduit. For supply connections, use suitable AWG wires suitable for at least 90 C (190 F).
-
Page 13: Heater Mounting
Heater Mounting SAUNACORE A non-metallic guard rail must be away from the residential sauna heater models by a minimum of 4 inches, and the residential heater models must be minimum 2 inches away from any vertical surface. There must be a minimum of 45 inches clearance above the heater to the ceiling and a minimum of 2 inches above the floor. -
Page 14: Components
Components SAUNACORE Standard, SE, & SV Figure 20 01- Bottom Connection Box 02- S/S Vaporizer Tank 03- Rear Body Panel w/conn box 04- Lowwer Heat Shield 05- Industrial Heating Element 06- FrontBody Panel 07- Body Heat Shield 08- Rock Grill... - Page 15 SAUNACORE Maintenance Instructions 1) Saunacore strongly recommends that the sauna floor is made of a material that is easily cleaned. Ceramic tile, concrete, marble, sheet vinyl, etc. are all suitable for use in a sauna. When the sauna floor is made of a non-porous material, it is easy to keep clean, sanitary and odour free.
- Page 16 So for energy efficient and service-free ALL HEATING UNITS ARE MANUFACTURED heaters, we feel you have made a good choice with us. Our heaters range TO MEET THE LATEST CSA, UL & CE SAFETY from 2000 watts to 21000 watts, and there are 4 physical sizes available: a REQUIREMENTS.
- Page 17 Sauna-Use Procedures SAUNACORE How to Enjoy the Best in Saunas... The Finnish Way Sauna material and wood thickness recommendation: Every sauna enthusiast will develop their own style once fully acquainted Materials recommendations for the sauna room and confident in the sauna process. There are no fixed rules to follow for should be a long lasting soft wood, such as cedar, red wood, etc.
- Page 18 Sauna-Use Procedures SAUNACORE The feet should be raised above the head level by using permanent footrests installed on the wall or by placing a portable footrest under the ankles. Portable back and headrests are ideal for greater levels of personal comfort and enjoyment.
-
Page 19: Limited Warranty
Warranty service can be obtained by sending your product to Saunacore (Call 905-951- 6662). Warranty repairs must be done only by Saunacore. Proof of purchase and a serial number of the product will be required before any services are performed.
Need help?
Do you have a question about the Heaters and is the answer not in the manual?
Questions and answers
What size wire to use from the controler to the heater (I.e. 14/2 )
The power supply wires from the Saunacore heater controller to the heater must use a suitable AWG wire rated for at least 90°C (190°F) and must be copper.
This answer is automatically generated