Harman Advance Pellet Stove Installation & Operating Manual
  1. Manuals
  2. Brands
  3. Harman Manuals
  4. Pellet stove
  5. Advance Pellet Stove
  6. Installation & operating manual

Harman Advance Pellet Stove Installation & Operating Manual

Pellet burning room heater
Hide thumbs Also See for Advance Pellet Stove:
Table of Contents

Advertisement

Quick Links

See also: Maintenance Manual
Installation & Operating manual
The harman Advance Pellet Stove
"Ce manuel est disponible en Français sur demande"
r22

SAFETY NOTICE

PlEASE rEAd ThIS ENTIrE mANuAl bEFOrE INSTAllATION ANd uSE OF ThIS PEllET FuEl-burNINg
rOOm hEATEr. FAIlurE TO FOllOw ThESE INSTruCTIONS COuld rESulT IN PrOPErTY dAmAgE, bOdIlY
INjurY, Or EvEN dEATh.
FOr uSE IN ThE u.S. ANd CANAdA. SuITAblE FOr INSTAllATION IN mObIlE hOmES
IF ThIS hArmAN STOvE IS NOT PrOPErlY INSTAllEd, A hOuSE FIrE mAY rESulT. FOr YOur SAFETY, FOllOw
INSTAllATION dIrECTIONS.
CONTACT lOCAl buIldINg Or FIrE OFFICIAlS AbOuT rESTrICTIONS ANd INSTAllATION INSPECTION
rEQuIrEmENTS IN YOur ArEA.
CONTACT YOur lOCAl AuThOrITY (SuCh AS muNICIPAl buIldINg dEPArTmENT, FIrE dEPArTmENT, FIrE
PrEvENTION burEAu, ETC.) TO dETErmINE ThE NEEd FOr A PErmIT.
CETTE guIdE d'uTIlISATION EST dISPONIblE EN FrANCAIS. ChEz vOTrE CONCESSIONNAIrE dE hArmAN
hOmE hEATINg.
SAvE ThESE INSTruCTIONS.
#3-90-09730

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Advance Pellet Stove and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Harman Advance Pellet Stove

Summary of Contents for Harman Advance Pellet Stove

  • Page 1: Safety Notice

    INjurY, Or EvEN dEATh. FOr uSE IN ThE u.S. ANd CANAdA. SuITAblE FOr INSTAllATION IN mObIlE hOmES IF ThIS hArmAN STOvE IS NOT PrOPErlY INSTAllEd, A hOuSE FIrE mAY rESulT. FOr YOur SAFETY, FOllOw INSTAllATION dIrECTIONS. CONTACT lOCAl buIldINg Or FIrE OFFICIAlS AbOuT rESTrICTIONS ANd INSTAllATION INSPECTION rEQuIrEmENTS IN YOur ArEA.
  • Page 3 The unit has an easy to clean combustion system with an ash pan that holds ash from 1 ton of burned premium pellets. Harman Advance Pellet Stove This unit is equipped with several different safety devices which will be explained later in this manual.
  • Page 4 Automatic Ignition/Operation The Advance pellet stove is more than just automatic ignition, it is also automatic temperature control. The automatic system will allow the fire size to be adjusted to match the heating needs and even put the fire out if necessary. If heat is needed after the fire is out, the Advance will automatically re-ignite and adjust the fire size to match the heating need.
  • Page 5 Automatic Start up Starting First Fire Igniter Switch to "AuTO" (up position) Make sure the unit is plugged into a 120 VAC, 60 HZ electrical source. The power light should be the only light lit. To avoid unwanted smoke, be sure there is no fuel or combustibles in the ash pan prior to lighting.
  • Page 6 Ignition/Operation The Advance Pellet Stove is capable of manual operation. This also allows the operator to manually control operation during an emergency (i.e. igniter failure.) The unit can be switched between "AUTO" and "MANUAL" at any time during operation.
  • Page 7 manual Start up Starting First Fire Igniter Switch to "mANuAl" (down Position) Fig. 4 Make sure the unit is plugged into a 120 VAC, 60 HZ electrical source. The power light should be the only light lit. To avoid unwanted smoke, be sure there is no fuel Fig.
  • Page 8 Fahrenheit. It also allows you to adjust the Requires special DDM monitor low side of each mode. stove temperature while in Stove Temp Mode using supplied to Harman Dealers the inner scale marked from 1 to 7. exclusively. Status light error messages:...
  • Page 9 178mm and follow-up inspections. Several issues must be addressed when selecting a suitable location for your Advance Pellet Stove. Observing required clearances to combustible materials, the proximity to a safe chimney or venting system, and the accessibility of electrical supply must all be considered. In addition,...
  • Page 10 removing Side doors for Installation removing Side doors Figure 9 Use hand hole to swing open side doors to at least Side Door Figure 10 Remove side doors by lifting upward on the door until the bottom pin is out of its hole. Move the bottom of Fig.

  • Page 11: Low Draft Voltage Adjustment

    low draft voltage Adjustment Combustion Motor Speed Control Low draft only set point. The small straight screwdriver slot is plastic; therefore, the unit can be adjusted while in operation. draft Meter bolt hole location Fig.15 Fig.14 These units are pre-tested at the factory with A simple draft test should be performed after exactly 120 Volts A.C., 60 Hz.
  • Page 12 room Sensor and Air grill Installation room Sensor Installation Air grill Installation Fig. 16 Fig. 17 The room sensor is a small temperature sensor Insert the two tail end hooks of the Air grill on the end of a 60" gray or black wire. This sensor Assembly up under the stove top edge.
  • Page 13 Run the vent above the roof. Outside Air: • Avoid venting into alcove locations. harman home heating and hearth & home • Vents should not terminate under overhangs, decks Technologies recommend attaching outside air in or onto covered porches.
  • Page 14 Inlet Cover part# 1-10-08542 AN ATTIC, rOOF SPACE, ClOSET, FlOOr, Or CEIlINg. direct vent wall Passthrough The harman direct vent wall Passthrough (Part # 1-00- Outside Air 677077) makes installing your harman Pellet Stove Outside air is necessary in mobile homes and where with outside air much easier.
  • Page 15 venting #1 Preferred method This method provides excellent venting for normal operation and allows the stove to be installed closest to the wall. One inch from the wall is safe; however, two or three inches allows better access to remove the rear panel.
  • Page 16 venting #3 Installing into an existing chimney This method can be used for normal operation. This method also provides natural draft in the event of a power failure. If the chimney condition is questionable you may want to install a liner as in method #6. ThE ChImNEY muST bE OF A TYPE SuITAblE FOr SOlId-FuEl burNINg.
  • Page 17 venting #5 Installing into an existing fireplace chimney This method provides excellent venting for normal operation. This method also provides natural draft in the event of a power failure. In Canada and some places in the US it is required that the vent pipe extend all the way to the top of the chimney.
  • Page 18 venting #7 Installing through the ceiling vent minimum flue vent configuration Through the ceiling vent, follow PL vent manufacturer's It is recommended that outside air be installed with recommendations when using wall and ceiling pass this venting configuration. through. Storm collar 12"...
  • Page 19 venting requirements for Terminating the venting H. A vent must not be installed within 3 feet (90cm) WARNINg: Venting terminals must not be recessed above a gas meter/regulator assembly when measured into a wall or siding. from the horizontal center-line of the regulator. NOTE: Only "pellet"...
  • Page 20 Safety Information dO NOT INSTAll A FluE dAmPEr IN ThE wArNINg EXhAuST vENTINg SYSTEm OF ThIS uNIT. mObIlE hOmE rEgulATIONS dO NOT AllOw INSTAllATION IN A rOOm dESIgNATEd FOr SlEEPINg. dO NOT CONNECT ThIS uNIT TO A ChImNEY FluE SErvINg ANOThEr APPlIANCE. CAuTION INSTAll vENT AT ClEArANCES SPECIFIEd ThE STruCTurAl INTEgrITY OF ThE...
  • Page 21 maintenance - Emptying Ashes Ash Pan removal and reattachment CAuTION: Surfaces are hot while in operation, wear gloves to protect from burns. Figure 29 Open side doors. Figure 30 Release spring latches on the right and left side of the ash pan. Fig.
  • Page 22 To remove the view door from the stove, hold the door by the bottom and lift upward, off of the hinge pins. See Fig. 36. The glass in your Harman stove is a special ceramic glass. Fig. 36 dO NOT abuse the glass by striking or slamming shut.
  • Page 23 maintenance - burn Pot burn Pot Cleaning and maintenance 1. Scrape the top holed surface and sides of the burn pot. (Fig 38) It is not necessary to completely remove all material from the burn pot. The excess will be pushed out during the next use.
  • Page 24 maintenance - Flame guide and brick Panel Flame guide and brick Panel removal for Firebox Brick panel Cleaning Figure 41 Flame Guide/ Slide brick panel straight upward with both hands. Brick panel holder Figure 42 Burn pot While holding the brick panel up with one hand, remove the flame guide from the top of the burn pot.
  • Page 25 maintenance - Combustion Intake Cover Cover Retainer Handle Cleaning and maintenance for the Combustion Intake Cover You will need to remove the combustion intake cover, behind the ash pan, to clean the fan blades and rear flue tube. Figure 45 Rotate the retainer cover handle counter-clockwise upward as far as it will go (approximately 90 Figure 46...
  • Page 26 maintenance - heat Exchanger Cleaning the heat Exchanger System 1. Remove brick panel and flame guide. (See Pg 24.) 2. Remove the ash pan. See Page 21. Slot 3. Remove flue baffles located on each side of the burnpot, see Fig. 48 & 49. The baffle is held in place by inserting the tab into the slot (located toward the outside of the firebox) and resting it on the hook tab located beside the burnpot.
  • Page 27 Damper Igniter Wire - Feeder Entry Location Advance Pellet Stove Safety devices The low draft Pressure Switch is a differential The Control board/ESP combination is responsible pressure switch that senses the negative pressure for all high limit safety control. There are 2 high limits, (draft) in the firebox.
  • Page 28 Trouble-Shooting STOvE dOES NOT FEEd SmOKE IS vISIblE COmINg OuT OF vENT 1. Air-fuel ratio is too rich. 1. No fuel in hopper. A. Feed rate too high. 2. Firebox draft may be too low for sensing switch in B. draft too low caused by a gasket leak. feeder circuit to operate.
  • Page 29 Fuel Specifications Fuel and Fuel Storage Size Pellet fuel quality can fluctuate from manufacturer to • Pellets are either 1/4 inch or 5/16 inch (6-8mm) in manufacturer, and even from bag to bag. diameter Hearth & Home Technologies recommends using only •...
  • Page 30 Specifications 20.5" 7.750" 5.250" 26.625" weight 250 lbs. blower 135 cfm hopper Capacity 60 lbs. Fuel wood Pellets or Corn/Pellet mix Outside Air Size 2 3/8 inches Fuse rating 6 amp bTu range 0 to 48,000 Feed rate 1.0 lbs./hr. on minimum 6 lbs./ hr.
  • Page 31 Advance wiring diagram...
  • Page 32 Hearth & Home Technologies Inc. LIMITED LIFETIME WARRANTY Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer. WARRANTY COVERAGE: HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance...
  • Page 33 WARRANTY CONDITIONS: • This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of HHT authorized dealers is available on the HHT branded websites. • This warranty is only valid while the HHT appliance remains at the site of original installation. •...
  • Page 34 Advance Service Parts Pellet Stove beginning manufacturing date: N/A 1-70-08730-1 (black) Ending manufacturing date: Active retired units 1-70-08730-2 (Charcoal) Ending Manufacturing date: June 2009) 1-70-08730-5 (Honey glo) (Ending Manufacturing date: June 2009) 1-70-08730-3 (goldenfi re) (Ending Manufacturing date: June 2009) 1-70-08730-10 (Mojave Red) (Ending Manufacturing date Jan 2010) 1-70-08730-4 (Metallic Blue) (Ending Manufacturing date Jan 2010) 1-70-08730-12 (Forest green) (Ending Manufacturing date Jan 2010...
  • Page 35 Advance Service Parts beginning manufacturing date: N/A Ending manufacturing date: Active #3 hopper lid Assembly IMPORTANT: THIS IS dATEd INFORMATION. When requesting service or replacement Stocked parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
  • Page 36 Advance Service Parts beginning manufacturing date: N/A Ending manufacturing date: Active IMPORTANT: THIS IS dATEd INFORMATION. When requesting service or replacement parts for Stocked your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer.
  • Page 37 Advance Service Parts beginning manufacturing date: N/A Ending manufacturing date: Active Pre Serial Number 008360001 24.1 Feeder Assembly 24.2 24.17 24.3 24.4 24.16 24.15 24.14 24.13 24.7 24.10 24.6 24.9 24.5 24.8 24.12 IMPORTANT: THIS IS dATEd INFORMATION. When requesting service or replacement Stocked parts for your appliance please provide model number and serial number.
  • Page 38 Advance Service Parts beginning manufacturing date: N/A Ending manufacturing date: Active Post Serial Number 008360001 Feeder Assembly 25.14 25.15 25.11 25.13 25.12 25.1 25.2 25.10 25.9 25.3 25.8 25.4 25.5 25.7 25.6 IMPORTANT: THIS IS dATEd INFORMATION. When requesting service or replacement Stocked parts for your appliance please provide model number and serial number.
  • Page 39 Advance Service Parts beginning manufacturing date: N/A Ending manufacturing date: Active IMPORTANT: THIS IS dATEd INFORMATION. When requesting service or replacement Stocked parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. at depot ITEm description...
  • Page 40 Addendum for Burning Corn and Pellet Fuel Mixture Harman pellet burning, free-standing stoves and inserts have been tested to ASTM E1509 for burning shelled corn in a mixture with wood pellets. The listing approves up to a 50% corn and 50% pellet mixture. Different mixtures of corn will have distinctively different burn characteristics depending upon moisture content and variety.
  • Page 41 Contact your dealer if you have questions about UPS compatibility with your appliance. harman Surefire 512h battery back-up The 512H connects to a 12 volt deep cycle battery that will run your appliance for up to eight (8) hours. It includes a trickle charge feature that keeps your battery charged when power is available.
  • Page 42 Service & maintenance log Date Of Service Performed By Description Of Service...
  • Page 44 At Harman, we build each product to a standard, not a price. This powerful heating appliance boasts uncompromising attention to detail and helps preserve our planet by using environmentally responsible fuels. (Signature of Boxer) Your premium quality hearth product designed and assembled by the experienced and skilled members at Harman in Halifax, PA, USA.

Table of Contents

Save PDF