Page 1
CALL MSPA AFTER SALES SERVICE CENTER FOR ANY PRODUCT QUESTIONS. CONTACT US AT info@the-mspa.com NE PAS RETOURNER LA MARCHANDISE DIRECTEMENT AU MAGASIN DE VENTE INITIAL. APPELER LE SERVICE APRÈS VENTE MSPA POUR TOUTE QUESTION SUR LE PRODUIT. NOUS CONTACTER AU info@the-mspa.com...
WARNING ! For your own safety and that of your equipment, make sure to take the following precautions. Failure to follow warning notices and instructions may result in property damage, serious injury or death. Improper installation or operation will void the warranty When install or use this equipment, basic safety precautious must be followed, including the following: IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS...
Page 3
WARNING: Do not expose spa under direct sunshine. WARNING – This product is provided with a ground-fault circuit-interrupter in the plug. The GFCI must be tested before each use. With the product operating, open the service door. When the product stops operating, this merely indicates that the door is equipped with an electrical interlock.
Page 4
A green coloured terminal or a terminal marked G, GR, Ground, Grounding, or the symbol* is located inside the supply terminal box or compartment. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying this equipment.
Page 5
The effects of hyperthermia include (a) unawareness of impending hazard; (b) failure to perceive heat; (c) failure to recognize the need to exit spa; (d) physical inability to exit spa; (e) fetal damage in pregnant women; and (f) unconsciousness and danger of drowning. WARNING: THE USE OF ALCOHOL OR DRUGS CAN GREATLY INCREASE THE RISK OF FATAL HYPERTHERMIA IN HOT TUBS AND SPAS WARNING: TO REDUCE THE RISK OF INJURY: Never pour water which higher than 40°C(104°F) into the spa pool...
Page 7
A. Site Requirements WARNING: The floor has to be capable of supporting the expected load. WARNING: An adequate drainage system has to be provided to deal with overflow water. IMPORTANT: Because of the combined weight of the spa, water and users, it is extremely important that the base where the spa is installed is smooth, flat, level and capable of uniformly supporting the weight for the entire time the spa is installed.
Page 8
It’s helpful to put temp barrier mat between spa and ground, or similar mat which is made of foam material or some material with temp barrier function. Don’t install Mspa onto the lawn as grass may cause air pump damped and rusted which could result the air pump works improperly and will void your warranty.
Page 9
3. Please reduce the air pressure to the yellow sector of manometer, to avoid over inflation due to warm weather or sunshine etc. after leaving Mspa for weeks inflated. Warning: to avoid function failure and damage to the control system, please do not...
l) Place the zipper cover onto the spa and then put the inflatable bladder onto the spa pool, Fasten the zip- per and lock the cover to the spa by using the digital lock in the accessory pack. Note: Please remember to test and adjust the air pressure inside of spa pool before each time of use.
5. Spa lid is not covered or improperly covered when heating 6. In order to conform to the safety regulations, MSpa control system uses double heating elements technology. When bubble+filter+heater functions are all on, only one heating element is working, which is of 675W only So you are recommended to fill spa with warm water for quick heating and energy...
Page 12
Special Notice on Water Treatment Please read about water quality and filter in user manual. Always shower before you enter your MSpa! Please use test strip to test your water chemistry before each use of the spa, no less than once per week.
Page 13
Spa checklist before unpack the unit and re-use for the new season: In order to have your MSpa runs smoothly and easily for another new season, make sure you do the follow: 1. Check if there is water in the air pipe. If any water is found, dry the air pipe before operating the spa tub.
Here are some helpful tips to help you to diagnose and rectify some common sources of trouble. *For any spare parts you need for replacement, please refer to the warranty policy for replacing details. *For any other unknown failures out of the list, please contact your national or regional MSpa service cen- ter.
Page 15
Transportation Prepaid, if requested. All The authorized selling dealer is responsible for all in-field service work carried out on your MSpa® prod- uct. ORPC will not be liable for results or cost of workmanship from unauthorized service persons or deal- ers.
Page 16
Any damage caused by clogged, dirty or calcified filters c. Any damage that are purely aesthetic and do not hinder the function of the MSpa d. Any damage to the exterior resulting from improper maintenance or any damage to the exterior attribut able to freight mishandling e.
Page 17
For Spa pool (body) problem – Picture of defect part need to be attached along with the mail-in warranty card and is MANDATORY to claim the warranty For electric part(s) or control box problem – Send the control box to your local MSpa Service Center. See the Service Center Contact List in the manual.
Need help?
Do you have a question about the B-090 B-091 Alpine and is the answer not in the manual?
Questions and answers
un mspa alpine delignt p90 accessoire nm series b0800015
The compatible accessories for the MSpa Alpine B-090 and B-091 models include:
- Spa cover inflatable bladder:
- B0301976 for B-090
- B0302010N for B-091
- Buckle spa cover:
- B9300688 for B-090
- B9300639 for B-091
- Ground mat set:
- B9300689 for B-090
- B9300707 for B-091
- Buckle spa cover and ground mat set:
- B-091 model compatible
Additional shared accessories (not model-specific):
- Inflation hose
- Manometer
- Filter cartridge (twin pack)
- Spa drain valve adaptor
- Repair kit
- Wrench
- Instruction DVD
- Digital cable cover and ST3*10 self-tapping screw
- Warning label
These parts may require matching the model number when ordering.
This answer is automatically generated