Advertisement
Quick Links
Advertisement
Related Manuals for mspa Blue Sea B110
Summary of Contents for mspa Blue Sea B110
-
Page 2: Safety Instructions Warning
SAFETY INSTRUCTIONS WARNING When installing and using this electrical equipment, basic safety precaution should always be followed, including the following: IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS. WARNING: RISK OF ELECTRIC SHOCK. Insert the plug only to a properly grounded socket. WARNING: The spa must be supplied by an isolating transformer or supplied through a ground-fault circuit interrupter (GFCI) having a rated residual operating current not exceeding 30mA. - Page 3 WARNING: TO REDUCE THE RISK OF INJURY: The water in a spa should never exceed . Water temperature between 38 (100 ) and 40 °C (104 °F) °C °F are considered safe for a healthy adult. Lower water temperature is recommended for 40 °C (104 °F) young children and when spa use exceeds 10 minutes.
-
Page 4: Specifications
SPECIFICATIONS Bubble Style No. B-110 Blue Sea B-130 Camaro B-140A/B Blue/brown (Elegance) A081027(blue) Item No. A081010 A081008 A081009(brown) Seating capacity Water capacity 1000L/265gallon 800L/211gallon 800L/211gallon Outer Diameter 1.88m/74" 1.8m/71" 1.8m/71" Inner Diameter 1.46m/58" 1.4m/55" 1.4m/55" Height 0.70m/28" 0.8m/32" 0.70m/28" Number of air jet Power rated 110~120V, 60Hz 110~120V, 60Hz... - Page 5 Site Requirements WARNING: The floor has to be capable of supporting the expected load. WARNING: An adequate drainage system has to be provided to deal with overflow water. IMPORTANT: Because of the combined weight of the spa, water, and users, it is extremely important that the base where the Spa is installed is smooth, flat, level and capable of uniformly supporting this weight for the entire time the spa is installed.
- Page 6 4 . Finally, press the “RESET” button again. The indicator light should turn red. The spa is ready for use. Assembly For B-130 and B-140 only Unfold the Spa pool from the packaging. Put the side leather cover on the spa tub. Spread the Spa and cover.
- Page 7 As previously outlined, test spa’s GFCI plug. Inflate the spa tub by pressing the “bubble” button Attention: Do not over inflate. Press the “bubble “ button to shut off the bubble function when the spa is properly inflated. Remove the inflation and Screw the valve tight Remove the inflation hose from the control panel and screw the valve tight Screw the filter cartridge onto the water inlet on the spa wall by turning it clockwise.
- Page 8 Note: For B-130, Open the air valve under the control panel device, then screw one end of air pipe on it. Unfold the top inflatable bladder. Open the air valve on the top inflatable bladder, Put the top leather cover on the top inflat- and screw the other end of air pipe on it.
- Page 9 Heat Button: Use this button to activate the heating system. The heater does not stop heating the Spa until the current water temperature reaches 1°C higher than the set temperature. After the current water temperature drops 2°C below the set point temperature the heating sys- tem will restart.
- Page 10 Drainage Turn off all the buttons on the control panel. Connect the hose with the outlet in the inner wall of the spa to drain, and the hose with the inlet to absorb water. Turn on the filter pump. Tilt the spa will allow the spa to thoroughly drain. Press the filter button once the spa is completely drained.
-
Page 11: Troubleshooting
Spa Repair If the Spa is torn or punctured use the provided Repair Patch. Dry the area to be repaired. apply the glue in the accessory bag to the repair patch and then attach it onto the damaged area. Smooth the surface to remove any air bubbles. -
Page 12: Safety & Announcements
Please contact your local community about collection points or ask your dealer. 2.This product contains valuable materials that can be recycled and contribute to a sustainable environment. 3.For recovery, recycling and dismantling information for this product, please visit us at www. the-mspa WATER PROTECTION LEVEL Warring: Water protection levels of Appliance at different product zones are different see the following scheme. - Page 13 Warranty Registration Card and mail it to the manufacturer within 15 days of date of receiving the purchase, or submit via our website at www.the- mspa.com. Transportation costs incurred to and from the manufacturer or authorized service center is the responsibil- ity of the purchaser.
- Page 14 Canada Warrantycare.com US- Consumers 888-521-6183 US-Dealers 888-661-6772 www.mspausa.com...
Need help?
Do you have a question about the Blue Sea B110 and is the answer not in the manual?
Questions and answers