Extron electronics DTP HDMI 230 User Manual
Hdmi twisted pair extender
Hide thumbs
Also See for DTP HDMI 230:
- Setup manual (2 pages) ,
- Setup manual (2 pages) ,
- Setup manual (2 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Setup Manual
Advertisement
Table of Contents
Related Manuals for Extron electronics DTP HDMI 230
Summary of Contents for Extron electronics DTP HDMI 230
- Page 1 User Guide HDMI & DVI Extenders DTP HDMI 230 HDMI Twisted Pair Extender 68-2244-01 Rev. A 04 13...
-
Page 2: Safety Instructions
Safety Instructions Safety Instructions • English Chinese Simplified （简体中文） WARNING: This symbol, , when used on the product, is intended 警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 to alert the user of the presence of uninsulated dangerous voltage 电压， 有触电危险。 within the product’s enclosure that may present a risk of electric shock. - Page 3 Attention indicates a situation that may damage or destroy the product or associated equipment. NOTE: A note draws attention to important information. Copyright © 2013 Extron Electronics. All rights reserved. Trademarks All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks...
-
Page 5: Table Of Contents
Installation and Operation ........3 Mounting the Units ..........3 Connections ............4 Transmitter Connections ......... 4 Receiver Connections ........5 Connector and Cable Details ......7 Operation ............10 DTP HDMI 230 Tx/Rx Transmitter and Receiver • Table of Contents... - Page 6 DTP HDMI 230 Tx/Rx Transmitter and Receiver • Introduction...
-
Page 7: Introduction
This guide describes the Extron DTP HDMI 230 Long Distance High Definition Multimedia Interface (HDMI) Twisted Pair Extender, which consists of a DTP HDMI 230 Tx transmitter and a DTP HDMI 230 Rx receiver. This guide describes how to install, operate, and configure the transmitter and receiver. -
Page 8: Tp Cable Advantages
The DTP HDMI 230 Tx/Rx units are housed in quarter rack width metal enclosures. They can be set on a tabletop or mounted in a rack, under or through furniture. The receiver can also be mounted on a projector bracket. -
Page 9: Installation And Operation
Installation and Operation This section describes the installation and the operation of the DTP HDMI 230 Tx/Rx Extender, including: • Mounting the Units • Connections • Operation Mounting the Units Mounting instructions and the can be found in Mounting the Transmitter or Receiver page 11. -
Page 10: Connections
HDMI input (transmitter) or any valid signal on the DTP In connector (receiver). Link LED — This LED lights when a valid link is established between the units on the DTP input and output cable. DTP HDMI 230 Tx/Rx Transmitter and Receiver • Installation and Operation... -
Page 11: Receiver Connections
• If you have removed the ground jumpers (see Disconnecting the Ground on page 12) because of ground potential differences, one DTP HDMI 230 unit cannot remotely power the other unit. Each unit requires a local power supply. Receiver Connections... - Page 12 • If you have removed the ground jumpers (see Disconnecting the Ground page 12) because of ground potential differences, the DTP HDMI 230 cannot extend analog audio. No analog audio is output. • The length of exposed wires is critical. The ideal length is 3/16 inch (5 mm).
-
Page 13: Connector And Cable Details
Twisted pair recommendations Supported cables — The DTP HDMI 230 is compatible with CAT 5e, 6, 6a, and 7 shielded twisted pair (F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable. Cable recommendations — Extron recommends using the following practices to achieve full transmission distances up to 230 feet (70 m) and reduce transmission errors. - Page 14 (see figure 8). Crimped Connector Figure 8. Crimped RJ-45 Connector DTP HDMI 230 Tx/Rx Transmitter and Receiver • Installation and Operation...
-
Page 15: Power Supply Wiring
If you have removed the ground jumpers (see Disconnecting the Ground page 12) because of ground potential differences, one DTP HDMI 230 unit cannot remotely power the other unit. Each unit requires a local power supply. Figure 9 shows how to wire the connector. Use the supplied tie-wrap to strap the power cord to the extended tail of the connector. -
Page 16: Operation
If the other devices are not turned on before the video source, the image may not appear. DTP HDMI 230 Tx/Rx Transmitter and Receiver • Installation and Operation... -
Page 17: Reference Information
The 1-inch high, quarter rack width DTP HDMI 230 transmitter or receiver can be placed on a table, mounted in a rack, or mounted under a desk or table. The receiver can also be mounted on a projector bracket. -
Page 18: Ul Rack-Mounting Guidelines
If you cannot resolve a ground potential difference between the transmitter and receiver installation sites, remove the ground connection between the units as follows: NOTE: Once you have removed the ground jumpers, the DTP HDMI 230 cannot extend analog audio and one unit cannot remotely power the other. No analog audio is output and each unit requires a local power supply. - Page 19 Obtain a second 12 V power supply (one supply is provided with the transmitter and normally powers both units), and locally power both units (see Power supply wiring on page 9). DTP HDMI 230 Tx/Rx Transmitter and Receiver • Reference Information...
- Page 20 Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.
Need help?
Do you have a question about the DTP HDMI 230 and is the answer not in the manual?
Questions and answers