Page 1
Water Works With Otterbine CONCEPT Owner's Manual A Guide to More Dependable Water Quality Management With Otterbine Barebo Inc.'s 1, 2, 3 & 5 Horsepower Surface Spray Aerating Fountain...
• If the power cord is damaged, it must be replaced by a special cord or assembly available from Otterbine/ Barebo, Inc. or an authorized Otterbine/Barebo, Inc. sales and service center. • Avant d'entrer, pataugeant dans ou en nageant dans l'eau dans laquelle Aérateurs Otterbine ou fontaines sont installées, assurez-vous qu'ils sont physiquement déconnectés de leur source d'alimentation électrique.
• Si le cordon d'alimentation est endommagé, il doit être remplacé par un cordon spécial ou de montage disponible à partir Otterbine / Barebo, Inc ou une autorisation Otterbine / Barebo, les ventes Inc et centre de service. INSPECT AERATOR EQUIPMENT Immediately report any shipping damage to the carrier that delivered your aerator.
OVERALL DIMENSION MOUNTING HOLE LAYOUT C. PCC Mounting 1. To prevent damage to the enclosure mount the enclosure using all four (4) mounting holes. 2. Whenever possible do not mount the PCC in direct sun light. D. PCC Cables & Connections 1.
*Genesis Pump Chamber; The Float MUST be mounted before the Genesis Throat Assembly (Shown on page 20). (The unit will be received with the pumping chamber already mounted) *5HP "Open Throat" Units (Sunburst, Gemini, Saturn); If applicable, the Supplemental Float must be mounted to the Main Float before installing on Unit (See Below).
Page 8
C. Mounting the Stabilizers (Comet Spray Pattern Only) 1. Mount each of the four stabilizer plates to the top side of a bracket using a hex bolt, a fender washer, and a nylon locknut as shown below. 2. Mount each of the four stabilizer plate assemblies from Step C1 to the top side of an outer hole in the float using an eyebolt, a fender washer, and a nylon locknut as shown.
PHYSICAL INSTALLATION WARNING: DISCONNECT POWER BEFORE INSTALLING, REMOVING, OR SERVICING UNIT Concept 3 Otterbine aerators require a minimum 30"/75cm (40"/100cm w/ lights) of water depth. A. Attach your Otterbine power cable to the aerator. 1. Align the keyway on the cable pigtail connector to the key on the aerator bulkhead connector and plug together.
SYSTEM STARTUP DO NOT ALLOW THE AERATOR TO OPERATE “DRY” OUT OF THE WATER IMPORTANT: Otterbine aerators are designed to run in a Counterclockwise direction facing the top impeller end. Current unbalance for three phase systems shall not exceed 5%. IMPORTANT: Aérateurs Otterbine sont conçus pour fonctionner dans le sens antihoraire regardant l'extrémité...
PHOENIX, TRI-STAR, CONSTELLATION, COMET, GENESIS, EQUINOX, and OMEGA. The GEMINI, SATURN, and SUNBURST pump higher volumes of water which helps to keep the water around the aerator from freezing and 24 hour a day operation will further decrease the opportunity for the unit to freeze-in, although during...
6. Place an O-ring on the top of the Throat Assembly. 7. Mount the Sunburst Ring to the Throat Assembly using (4) M5x50 S/S Hex Screws, (4) M5 S/S Flat Washers, and (4) M5 S/S Split Lock Washers. Tighten the screws evenly in...
GEMINI PUMP CHAMBER Gemini Assembly Instructions 1. Mount the Standoff Strainer Assembly to the power unit using (4) M5x50 S/S Hex Screws, (4) M5 S/S Flat Washers, (4) M5 S/S Split Lock Washers, and (4) M5 S/S Hex Nylon Locknuts. Tighten the screws evenly. NOTE: Standoff Strainer Assembly is not part of the Pump Chamber Assembly.
5. Place an O-ring on the top of the Throat Assembly. 6. Mount the Sunburst Ring to the Throat Assembly using (4) M5x50 S/S Hex Screws, (4) M5 S/S Flat Washers, and (4) M5 S/S Split Lock Washers. Tighten the screws evenly in...
ROCKET PUMP CHAMBER Rocket Assembly Instructions 1. Mount the Standoff Strainer Assembly to the power unit using (4) M5x50 S/S Hex Screws, (4) M5 S/S Flat Washers, (4) M5 S/S Split Lock Washers, and (4) M5 S/S Hex Nylon Locknuts. Tighten the screws evenly. NOTE: Standoff Strainer Assembly is not part of the Pump Chamber Assembly.
PHOENIX PUMP CHAMBER Phoenix Assembly Instructions 1. Mount the Standoff Strainer Assembly to the power unit using (4) M5x50 S/S Hex Screws, (4) M5 S/S Flat Washers, (4) M5 S/S Split Lock Washers, and (4) M5 S/S Hex Nylon Locknuts. Tighten the screws evenly. NOTE: Standoff Strainer Assembly is not part of the Pump Chamber Assembly.
TRI-STAR PUMP CHAMBER Tri-Star Assembly Instructions 1. Mount the Standoff Strainer Assembly to the power unit using (4) M5x50 S/S Hex Screws, (4) M5 S/S Flat Washers, (4) M5 S/S Split Lock Washers, and (4) M5 S/S Hex Nylon Locknuts. Tighten the screws evenly. NOTE: Standoff Strainer Assembly is not part of the Pump Chamber Assembly.
CONSTELLATION PUMP CHAMBER Constellation Assembly Instructions 1. Mount the Standoff Strainer Assembly to the power unit using (4) M5x50 S/S Hex Screws, (4) M5 S/S Flat Washers, (4) M5 S/S Split Lock Washers, and (4) M5 S/S Hex Nylon Locknuts. Tighten the screws evenly. NOTE: Standoff Strainer Assembly is not part of the Pump Chamber Assembly.
COMET PUMP CHAMBER Comet Assembly Instructions 1. Mount the Standoff Strainer Assembly to the power unit using (4) M5x50 S/S Hex Screws, (4) M5 S/S Flat Washers, (4) M5 S/S Split Lock Washers, and (4) M5 S/S Hex Nylon Locknuts. Tighten the screws evenly. NOTE: Standoff Strainer Assembly is not part of the Pump Chamber Assembly.
GENESIS PUMP CHAMBER Genesis Assembly Instructions 1. Mount the Standoff Strainer Assembly to the power unit using (4) M5x50 S/S Hex Screws, (4) M5 S/S Flat Washers, (4) M5 S/S Split Lock Washers, and (4) M5 S/S Hex Nylon Locknuts. Tighten the screws evenly. NOTE: Standoff Strainer Assembly is not part of the Pump Chamber Assembly.
Limited 5 Year Warranty Otterbine® Product WARRANTY: Barebo, Inc 3840 Main Road East, Emmaus Pennsylvania 18049,U.S.A. hereby warrants, subject to the conditions herein below set forth, that should the OTTERBINE product prove defective by reason of improper workmanship or materials at any time during the warranty period the Purchaser at retail will be guarantee that BAREBO will repair or replace the said OTTERBINE product as may be necessary to restore it to satisfactory operating condition, without any charge for materials or labor necessarily incident to such repair or replacement, provided that:...
Page 24
MODEL (circle one): Sunburst Gemini Rocket Phoenix Tri-Star Saturn Comet Constellation Genesis Omega Equinox HORSEPOWER (circle one): VOLTAGE (circle one): 208-230 PHASE (circle one): Single Three HERTZ (circle one): CORD GAUGE & LENGTH_______________________________________________________ UNIT SERIAL NUMBER _________________________________________________________ PANEL SERIAL NUMBER _______________________________________________________...
Need help?
Do you have a question about the Sunburst and is the answer not in the manual?
Questions and answers