Intel 845GV User Manual
  1. Manuals
  2. Brands
  3. Intel Manuals
  4. Motherboard
  5. 845GV
  6. User manual
Intel 845GV User Manual

Intel 845GV User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

CONTENTS
JUMPER SETTING AND SLOT...........................................
4.1
CPU INSTALLATION.......................................................
4.2
MEMORY INSTALLATION...............................................
4.3
IDE DEVICES INSTALLATION..........................................
4.4
OTHER DEVICE INSTALLATION.......................................
4.5
CHAPTER 5
5.1
INSTALLATION DIRECTORY...........................................
5.2
INTEL CHIPSET SOFTWARE SETUP...................................
5.3
5.4
SOUND DRIVER SETUP....................................................
5.5
USB 2.0 DRIVER SETUP...................................................
6.1
MAIN MENU..................................................................
6.2
STANDARD CMOS FEATURES..........................................
6.3
ADVANCED BIOS FEATURES............................................
6.4
ADVANCED CHIPSET FEATURES.......................................
6.5
INTEGRATED PERIPHERALS.............................................
6.6
POWER MANAGEMENT SETUP..........................................
6.7
PNP/PCI CONFIGURATIONS...............................................
6.8
FREQUENCY/VOLTAGE CONTROL.....................................
6.9
LOAD FAIL-SAFE DEFAULTS.............................................
6.10
LOAD OPTIMIZED DEFAULTS............................................
6.11
CHANGE PASSWORD........................................................
6.12
SAVE EXIT & WITHOUT SAVE EXIT SETUP..........................
Intel845GL/GV Main board
User's Manual
Rev: 1.0/1.2
PCB: M248
PACKAGE CONTENTS...........................................
INTRODUCTION....................................................
MAIN BOARD LOCATIONS.....................................
INSTALLATION....................................................
DRIVE INSTALLATION..........................................
BIOS SETUP.........................................................

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 845GV and is the answer not in the manual?

Questions and answers

Related Manuals for Intel 845GV

Summary of Contents for Intel 845GV

  • Page 1: Table Of Contents

    MEMORY INSTALLATION……………………………………….. IDE DEVICES INSTALLATION…………………………………... OTHER DEVICE INSTALLATION………………………………... CHAPTER 5 DRIVE INSTALLATION…………………………………… INSTALLATION DIRECTORY……………………………………. INTEL CHIPSET SOFTWARE SETUP…………………………….. IAA (INTEL APPLICATION ACCELERATOR) SETUP………….. SOUND DRIVER SETUP………………...…………………………. USB 2.0 DRIVER SETUP…………………………………………… CHAPTER 6 BIOS SETUP………………………………………………… MAIN MENU………………………………………………………… STANDARD CMOS FEATURES…………………………………… ADVANCED BIOS FEATURES……………………………………..

  • Page 2: Chapter 1 Package Contents

    This main board has the Intel 845GL/GV chipset that contains Intel 82845GL/GV Memory Controller Hub and Intel 82801DB I/O Controller Hub. This main board has a Socket-478 support for Intel Pentium 4 processors with front-side bus (FSB) speeds up to...
  • Page 3 -Integrated display function technologies without extend VGA card Integrated 2D/3D Graphics Controller -USB Ports Six USB ports Supports compliant with Universal Serial Bus Specification Revision 2.0 -BIOS Supports Supports Plug and Play Supports Advanced Power Management Interface -IDE Port Provides two channel connecting four IDE drives Supports Ultra ATA66/100 synchronous DMA modes -I/O Ports One Floppy port support format 360k/720k/1.2M/1.44M/2.88M disk driver...

  • Page 4: Chapter 3 Main Board Locations

    Chapter 3 Main board Locations...

  • Page 5: Chapter 4 Installation

    Chapter 4 Installation 4.1 Jumper Setting and Slot FSB CPU Frequency Jumper Setting JUMPER AUTO (Default) OPEN JP3: Clear CMOS Jumper Setting 1-2 (Default) Normal Clear CMOS Audio: Front panel Jumper setting Function Function MIC+ Ground Vbias AuD_Vcc (AVCC) AuD_R_Out AuD_R_Out Back N.C.

  • Page 6: Cpu Installation

    Connectors PS/2 (Bottom) PS/2 Keyboard (Down Purple) PS/2 (Top) PS/2 Mouse Header (Up Green) USB 0/1 USB 0/1 Connector Port USB 2/3 USB 2/3 Connector Port Printer Connector Port VGA Display Connector Port COM1 Serial Ports COM1 Connector Port GAME/MIDI Game/MIDI Port LINE OUT/LINE IN/MIC Audio Output/Audio Input/Microphone...

  • Page 8: Memory Installation

    4.3 Memory installation This main board supports DDR200/DDR266 DDR memory you may install 64/128/256/512MB 184 pin DDR memory. DDR SDROM uses additional power and ground lines and requires 184-pin 2.5V unbuffered DIMM module rather than the 168- pin 3.3V unbuffered DIMM used by SDRAM. Follow these instructions to install the Memory: 1.

  • Page 9: Other Device Installation

    4.5 Other Device Installation 4.5.1 Floppy Disk Drive Installation This main board ships with a floppy disk drive cable that can support one or two drives. Drives can be 3.5” or 5.25” wide, with capacities of 360K, 720K, 1.2MB, 1.44MB, or 2.88MB.

  • Page 10: Installation Directory

    Before installing audio driver, you must identify the mode of AC’ 97 codec. For example: If you use realtek serial codec, you need to enter into the realtek directory installing. 5.2 Intel Chipset Software Setup Insert the driver CD, running driver software CD, choose the directory: \CD- ROM:\INTEL\INF\XXX...
  • Page 11 Click “NEXT” to continue Select “YES” to continue...
  • Page 12 Select “NEXT” to continue Select “FINISH” completing the installation.

  • Page 13: Iaa (Intel Application Accelerator) Setup

    5.3 IAA (Intel Application Accelerator) Setup Insert the driver CD, running driver software CD, choose the directory: \CD-ROM:\INTEL\IAA\XXX Click “Next” to continue Select “Yes” to continue...
  • Page 14 Select “Next” to continue Select “Next” to Continue...

  • Page 15: Sound Driver Setup

    Select “Finish” to complete the installation 5.4 Sound Driver Setup 5.4.1 Sound driver setup (For Realtek series of WIN98 operation system) Insert the driver CD, running driver software CD, choose the Directory:\CD-ROM:\SOUND\REALTEK\SETUP.EXE Select “Next” to continue...

  • Page 16: Usb 2.0 Driver Setup

    Select “Finish” to complete the installation Channel Sound Output Support Please follow the steps below for operation (optional): 1. After install sound driver’ click “Sound effect”, “AC97 audio configuration” options; 2. Click “Sound configuration” select “6 Channel mode for 5.1 speakers output” options. 3.
  • Page 17 Select “Device manager” to continue Select “PCI Universal Serial Bus” and double click to continue...
  • Page 18 Select “Reinstall Driver” to continue Select “Next” to continue...
  • Page 19 Select “Next” to continue Select “Specify a location” and type “F:\INTEL\USB20\845\WIN98_ME” that...
  • Page 20 Select “Next” to continue Select “Next” to Continue...
  • Page 21 Select “Next” to Continue Select “Next” to Continue...
  • Page 22 Select “OK” to Continue Type “F:\INTEL\USB20\845\WIN98_ME” that Select “OK” to continue Select “Finish” continuing 5.5.2 Windows 2000/XP driver setup, new may run windows update to setup by internet.

  • Page 23: Chapter 6 Bios Setup

    Chapter 6 BIOS Setup The BIOS Setup Utility record settings and information of your computer, such as date and time, the type of hardware installed, and various configuration settings. Your computers applies those information to initialize all the component’s when booting up and basic function of coordination between system components.
  • Page 24 Setup BIOS provides function, for example virus, boot-strap induct Advanced Chipset Features Setup main board chipset parameter’ for example DRAM Timing Integrated Peripherals Setup include main board all peripherals drive Power Management Setup Setup CPU, Hard disk, Monitor drive power save mode PnP/PCI Configurations Setup PnP and PCI interface parameter PC Health Status...
  • Page 25 Boot Other Device If you enable this item, the system will also search for other boot devices if it fails to find an operating system from the first two locations. Swap Floppy Drive If you have two diskette drives installed and you enable this item, drive A becomes drive B and drive B becomes drive A.
  • Page 26 Init Display First When boot-start the first time detect device Default: PCI slot Onboard FDC Controller Setup onboard FDC controller Default: Enabled Onboard Serial Port ½ Setup onboard serial Port ½ Default: 3F8/IRQ4 UART Mode Select Setup UART mode select Default: Normal Onboard Parallel port Setup select parallel port...

  • Page 27: Frequency/Voltage Control

    6.8 Frequency/Voltage Control Auto Detect PCI CIK Setup auto detect PCI clock Default: Enabled CPU Clock Setup CPU BUS frequency Note: The main board auto detect CPU frequency ‘so you needn’t setup CPU frequency by yourself the CPU can display normal. 6.9 Load Fail-Safe Defaults If you select this item and press enter a dialog box appears.

This manual is also suitable for:

845gl

Table of Contents