Table of Contents
Advertisement
Owner's Manual & Safety Instructions
Save This Manual
inspection, maintenance and cleaning procedures. Write the product's serial number in the back of the manual
near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and
the receipt in a safe and dry place for future reference.
280cc
Saw Mill
using an engine indoors
Can Kill YOu in minuteS.
engine exhaust contains carbon monoxide.
this is a poison you cannot see or smell.
neveR use inside
a home or garage,
even iF doors and
windows are open.
When unpacking, make sure that the product is intact and undamaged.
If any engine parts are missing or broken,
please call 1‑800‑520‑0882 (engine parts) or
1‑800‑444‑3353 (other parts) as soon as possible.
©
Copyright
2013 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly, operating,
Only use OutSiDe
and far away from
windows, doors,
and vents.
visit our website at: http://www.harborfreight.com
email our technical support at: tech@harborfreight.com
or engine technical support at: predator@harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
Save thiS manual.
ITEM 61712
Advertisement
Table of Contents
Related Manuals for Central Machinery 61712
Summary of Contents for Central Machinery 61712
- Page 1 No portion of this manual or any artwork contained herein may be reproduced in Failure to do so can result in serious injury. any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing Save thiS manual.
-
Page 2: Table Of Contents
Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. Page 2 For technical questions, please call 1-800-520-0882. ITEM 61712... -
Page 3: Safety
Caution is necessary when near the engine's magneto or recoil starter. 7. Use only accessories that are recommended by Harbor Freight Tools for your model. Only use OUTSIDE and far away from windows, Accessories that may be suitable for one doors, and vents. - Page 4 23. Use the correct equipment for the application. (California Health & Safety code § 25249.5, et seq.) Do not modify the equipment and do not use the equipment for a purpose for which it is not intended. Page 4 For technical questions, please call 1-800-520-0882. ITEM 61712...
-
Page 5: Save These Instructions
These carry important information. d. Refuel in a well‑ventilated area only. If unreadable or missing, contact Harbor Freight Tools for a replacement. Save theSe inStRuCtiOnS. ITEM 61712 For technical questions, please call 1-800-520-0882. -
Page 6: Specifications
2. Secure Wheels (1) onto Left Wheel Frame (3a) with two Hex Bolts M20x100 (6) and Hex Nuts M20 (2). Then attach Left Wheel Frame, Square Post (48) and Square Clamp (4) Page 6 For technical questions, please call 1-800-520-0882. ITEM 61712... - Page 7 5. Lay out the Track sections (78, 92) as shown below. of the Track must be 30.315″ + 0.04″ Saw mill finishes cut Figure e: track assembly at this end. ITEM 61712 For technical questions, please call 1-800-520-0882. Page 7...
- Page 8 Allow for no more than 1/4″ - 1/2″ movement up or down (“give”) on the Blade. The 1/4″ - 1/2″ give indicates proper Blade tension. Figure j: Water tank tray and external tube Page 8 For technical questions, please call 1-800-520-0882. ITEM 61712...
- Page 9 Blade and the top of the Middle Support (81a) are the same. nOte: Adjust Blade again after replacement. nOte: Use a tape measure to verify distances match. ITEM 61712 For technical questions, please call 1-800-520-0882. Page 9...
-
Page 10: Operation
Clamp is below the level of the blade. 10. Tighten all Bolts and T‑Handles on the Log Clamp (89) and the Log Supports (82, 91). Verify that they are securely in place before proceeding. Page 10 For technical questions, please call 1-800-520-0882. ITEM 61712... - Page 11 Figure t: Direction of Cut then store the equipment out of children's reach according to the Storage instructions in this manual. ITEM 61712 For technical questions, please call 1-800-520-0882. Page 11...
-
Page 12: Maintenance
3. Apply a thin coat of rust preventive oil to all uncoated metal parts. Page 12 For technical questions, please call 1-800-520-0882. ITEM 61712... - Page 13 Remove stray branches that prevent proper positioning. 4. Teeth filled with debris. 4. Clean debris off blade. Follow all safety precautions whenever diagnosing or servicing the equipment or engine. ITEM 61712 For technical questions, please call 1-800-520-0882. Page 13...
-
Page 14: Parts List And Diagrams
Cable Anchor Bolt Water Tube Hex Nut M10 Spring Washer 10 Square Post Hex Nut M10 Hex Bolt M12×65 Blade Roller Bearing Blade Guard Top Frame Brace Hex Bolt M12×45 Page 14 For technical questions, please call 1-800-520-0882. ITEM 61712... -
Page 15: Assembly Diagram
Diagram ITEM 61712 For technical questions, please call 1-800-520-0882. Page 15... - Page 16 Diagram (continued) Page 16 For technical questions, please call 1-800-520-0882. ITEM 61712...
- Page 17 Diagram (continued) ITEM 61712 For technical questions, please call 1-800-520-0882. Page 17...
- Page 18 If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 18 For technical questions, please call 1-800-520-0882. ITEM 61712...
-
Page 19: Warranty
90 Day Warranty Harbor Freight Tools Co. makes every effort to assure To take advantage of this warranty, the product or part that its products meet high quality and durability must be returned to us with transportation charges standards, and warrants to the original purchaser prepaid. - Page 20 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 520-0882...
Need help?
Do you have a question about the 61712 and is the answer not in the manual?
Questions and answers
lock handle bolt right side has broken need replacement
To replace the broken lock handle bolt on a Central Machinery 61712:
1. Identify the lock handle that needs replacement:
- Left Lock Handle (54) or Right Lock Handle (59).
2. Obtain the correct replacement bolt:
- Left Lock Handle uses a Hex Bolt M8×45.
- Right Lock Handle may use a similar bolt.
3. Loosen and remove the broken bolt using appropriate tools.
4. Insert the new Hex Bolt M8×45 into the lock handle.
5. Tighten the bolt securely to ensure proper function.
If additional parts are damaged, contact the provided support numbers for replacements.
This answer is automatically generated