Page 2
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
CDP-CX455 SECTION 1 SERVICE NOTE TABLE OF CONTENTS NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT 1. SERVICE NOTE ······························································· 3 The laser diode in the optical pick-up block may suffer electrostatic 2. GENERAL ·········································································· 6 break-down because of the potential difference generated by the charged electrostatic load, etc.
Page 4
CDP-CX455 CD-TEXT TEST DISC This unit is able to display the TEXT data (character information) written in the CD on its fluorescent indicator tube. The CD-TEXT TEST DISC (TGCS-313:J-2501-126-A) is used for checking the display. To check, perform the following procedure.
Page 5
CDP-CX455 Table 2: CD-TEXT TEST DISC Recorded Contents and Display (In this unit, some special characters cannot be displayed. This is no a fault.) TRACK Recorded contents Display ! ” # $ % & ´ (21h to 27h)1kHz 0dB L&R...
CDP-CX455 SECTION 3 DISASSEMBLY CASE MAIN BOARD FRONT PANEL ASSEMBLY TRANS BOARD BACK PANEL SECTION COVER (PT), JOG BOARD, CD MECHANISM, DISP BOARD, MAGNET ASSEMBLY TABLE (400) ASSEMBLY KEYBOARD BOARD LED BOARD, GUIDE (DOOR) DOOR SW BOARD LOADING SW BOARD,...
CDP-CX455 Note : Follow the disassembly procedure in the numerical order given. 3-1. Case 1 three screws (case 3 screw) 2 two screws (case 3 screw) 3 two screws (case 3 screw) 5 case 4 two screws (case 3 screw) 3-2.
CDP-CX455 3-16. LOADING SW Board, LOCK SW Board 2 screw (BVTP3 × 8) 1 rotate the pulley (400) in the direction of the arrow fully. 3 rotate the pulley (400) in the direction of the arrow fully. 7 gear (center)
CDP-CX455 SECTION 4 TEST MODE • This unit is provided with several test modes. Details are shown in the following tables. <Menu Method> Turn on the power and press TIME , MEGA CONTROL and 1/u buttons. Rotate the DISC/ALBUM/CHARACTER dial to select any of the following modes.
Page 21
CDP-CX455 SOFT WARE VERSION DISPLAY Special Aging Mode Functions • Software version can be displayed on the fluorescent indicator tube. The aging mode is provided with the following convenient func- tions Procedure: With the power ON, while pressing the TIME and MEGA CONTROL 1.Disc setting mode:...
Page 22
CDP-CX455 Error Display Error code 2 1. Disc sensor error Code number Contents Error during loading in NEXT DISC ART. TRACK GROUP ART. STEP Error during loading out 1 2 0 With no problem SHUFFLE REPEAT GROUP With no problem...
Page 23
CDP-CX455 SHIPMENT MODE ALL LIT MODE • This mode is used for setting the unit to the shipment state. • This mode is used for lighting the whole fluorescent indicator Do not execute it without a proper reason as it erases the tubes and LEDs.
Page 24
CDP-CX455 ADJ Mode Key and Display Check Mode Turn ON the power of the unit, set disc to disc table, and perform To set this mode, connect the test point (AFADJ) on the MAIN chucking. board to Ground, and connect the power supply plug to the outlet.
CDP-CX455 SECTION 5 ADJUSTMENTS Mechanical Adjustments Table Sensor Adjustment Enter the CDM Test mode and select “Mech Adjust” with the Pop Up Mechanism Adjustment JOG dial, and press the dial. Turn on the power and set the disc to number 24.
Page 26
CDP-CX455 Electrical Adjustment RF Level Check oscilloscope Note: BD board CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. TP (RFAC) Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. TP (DVC) Use an oscilloscope with more than 10MΩ impedance.
Page 27
CDP-CX455 Disc Sensor Adjustment Rotate the DISC/ALBUM/CHARACTER knob in the Be sure to perform this adjustment after sensor adjustment in counterclockwise direction and the disc table starts to rotate in MECHANICAL ADJUSTMENT. the same direction. Check that the waveform at this time is the same as that in step 4.
Page 28
CDP-CX455 Adjustment Location : [ BD BOARD ] – Conductor Side – IC 101 TP(RF AC) TP(DVC) IC 103 TP(FE1) [ MAIN BOARD ] – Component Side – – Conductor Side – RV501 DISC SENSOR ADJUSTMENT TP(AFADJ) TP(ADJ) IC504 IC501...
CDP-CX455 SECTION 6 DIAGRAMS 6-1. Circuit Boards Location Waveforms THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. IC104 yd XO (In addition to this, the necessary note is printed LED board in each block.) For schematic diagrams.
CDP-CX455 6-2. Block Diagrams – BD Section – OPTICAL PICK-UP BLOCK IC101 DIGITAL SERVO IC103 (KSM-213BFN) RF AMP DIGITAL SIGNAL PROC. IC901 DIGITAL J903 OPTICAL RF AC RFAC D OUT OPTICAL CD IN RFDCO RFDC IC104 Q324 D/A CONV, RFDCI...
CDP-CX455 6-4. Schematic Diagram – BD Board – • See page 29 for Waveforms. • See page 44, 45 for IC Block Diagrams. • See page 46 for IC Pin Function Description. IC B/D IC B/D...
CDP-CX455 6-17. IC Pin Function Descriptions • IC104 TC94A20F-CX4 D/A Converter, MP3 Decoder (BD Board) Pin No. Pin Name Description /RESET Reset input terminal “L”: reset MIMD Microcomputer interface mode selection input “H”: I2C, “L”: TSB (fixed at “H”) /MICS Microcomputer interface chip select signal input (fixed at “L”)
Page 47
CDP-CX455 Pin No. Pin Name Description VSSP – Ground for VCO circuit PLL phase error detection signal output VCOI VCO control voltage input VDDP – Power supply (2.5V) for VCO circuit External clock output VDDX – Power supply (2.5V) for oscillation circuit...
Page 48
CDP-CX455 • IC501 µPD703033AYGF-CX4-3BA System Control (MAIN Board) Pin No. Pin Name Description FLDATA Data signal output to the fluorescent indicator drivers amd LED driver FLCLK Clock signal output to the fluorescent indicator drivers and LED driver LEDLAT Latch signal output to the LED driver...
Page 49
CDP-CX455 Pin No. Pin Name Description 51 to 57 D1 to D7 SRAM data bus BVDD – Power supply (I/O port) BVSS – Ground (I/O port) 60, 61 A13, A14 SRAM address signal output SRAM address signal output 63 to 70...
CDP-CX455 SECTION 7 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • -XX, -X mean standardized parts, so they may The components identified by mark 0 or number in the exploded views are not supplied. dotted line with mark 0 are critical for safety.
CDP-CX455 7-9. Optical Pick-up Section (BU-K1BD46A) Ref. No. Part No. Description Remark The components identified by Les composants identifiés par mark 0 or dotted line with mark une marque 0 sont critiques 1-782-817-11 WIRE (FLAT TYPE) (16 CORE) 0 are critical for safety.
CDP-CX455 SECTION 8 ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in the parts • SEMICONDUCTORS The components identified by list may be different from the parts specified in the In each case, u: µ , for example: mark ! or dotted line with mark diagrams or the components used on the set.
Page 60
CDP-CX455 D.MOTOR D.SENS(IN) D.SENS(OUT) DISP Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks FB111 1-216-864-11 METAL CHIP 1/16W R232 1-216-817-11 METAL CHIP 1/16W FB251 1-414-594-11 FERRITE R233 1-216-817-11 METAL CHIP 1/16W FB291 1-216-864-11 METAL CHIP 1/16W...
Page 68
CDP-CX455 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...
Need help?
Do you have a question about the CDP-CX455 and is the answer not in the manual?
Questions and answers