Honeywell PRO TH4110D Installation Manual
Honeywell programmable thermostat installation guide
Hide thumbs
Also See for PRO TH4110D:
- Installation manual (24 pages) ,
- Operating manual (72 pages) ,
- Operating manual (48 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Honeywell PRO TH4110D
Summary of Contents for Honeywell PRO TH4110D
-
Page 1: Installation Guide
Installation Guide TH4110D Programmable Thermostat... -
Page 2: System Settings
If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal. Copyright © 2005 Honeywell International Inc. All rights reserved. Power Type • Battery power •... -
Page 3: Table Of Contents
Installer setup...8 Installer system test ...8 Installation tips Install the thermostat about 5 feet (1.5m) above the floor in an area with good air circulation at average temperature. Do not install in locations where the thermostat can be affected by: •... -
Page 4: Pre-Installation Checklist
Installation Guide Pre-installation checklist Package contents Check to make sure your package includes the following items: • PRO TH4110D digital thermostat (wallplate attached to back) • Operating manual • Wall anchors and mounting screws (2 each) • AA alkaline batteries (2) •... -
Page 5: Wallplate Installation
PRO TH4110D Programmable Thermostat Wallplate installation Grasp top and bottom of wallplate and pull to remove from thermostat. Drill 3/16” holes for drywall. Drill 7/32” holes for plaster. Wall anchors Remove the wallplate from the ther- mostat as shown at left, then follow directions below for mounting. -
Page 6: Wiring
If wiring to a heat pump, use a small piece of wire (not supplied) to connect terminals W and Y. C terminal The C (common wire) terminal is optional when thermostat is powered by batteries. Wire specifications Use 18- to 22-gauge thermostat wire. Shielded cable is not required. Wiring... -
Page 7: Wiring Diagrams
PRO TH4110D Programmable Thermostat Wiring diagrams Power supply. Provide disconnect means and overload protection as required. Factory-installed jumper. Remove for 2-transformer systems only. Use either O or B terminals for changeover valve. Use a small piece of wire (not supplied) to connect W and Y terminals. -
Page 8: Fan Operation Settings
(This setting is for systems that allow the thermostat to control the fan in a call for heat, if a fan wire is connected to the G G terminal.) -
Page 9: Power Options & Mounting
PRO TH4110D Programmable Thermostat Power options & mounting Connect common side of transformer to “C” terminal Install batteries in back of thermostat (optional if AC powered). AC Power The thermostat can be powered by 24 VAC power, or by batteries. -
Page 10: Installer Setup
Installation Guide Installer setup Follow the procedure below to configure the thermostat to match the installed heating/cooling system, and customize feature operation as desired. Press and hold both buttons To begin, press and hold the buttons until the display changes... - Page 11 PRO TH4110D Programmable Thermostat Installer system test Follow the procedure below to test the heating and cooling system. System switch 1 Set S S Y Y S S T T E E M M switch to Cool. 2 Press to turn on cooling system, then check system status (see table, below).
-
Page 12: Built-In Compressor Protection
Adaptive Intelligent Recovery Adaptive Intelligent Recovery eliminates guesswork when setting your schedule. It allows the thermostat to “learn” how long your furnace and air conditioner take to reach the temperature you want. Just set your program schedule to the time you want the house to reach your desired temperature.The thermostat then turns on the heating or cooling at just the... -
Page 13: Quick Reference To Controls
PRO TH4110D Programmable Thermostat Quick reference to controls Temperature adjustment Fan switch On: Fan runs continuously. Auto: Fan runs only when heating or cooling system is on. Quick reference to display screen Low battery warning Current inside temperature Current program period... -
Page 14: In Case Of Difficulty
Installation Guide In case of difficulty If you have difficulty with your thermostat, please try the suggestions below. Most problems can be corrected quickly and easily. Display is blank • Check circuit breaker and reset if necessary. • Make sure heating & cooling power switches are on. -
Page 15: Accessories
PRO TH4110D Programmable Thermostat Accessories Please contact your distributor to order accessories. Cover plate assembly ...Part Number 50002883-001 (Used to cover marks left by old thermostats.) Specifications Temperature Ranges • Heat: 40° to 90°F (4.5° to 32°C) • Cool: 50° to 99°F (10° to 37°C) Operating Ambient Temperature •... - Page 16 Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered Trademark. © 2005 Honeywell International Inc. Patents pending. All rights reserved. 69-1849 • 06-2005 Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Scarborough, Ontario M1V 4Z9...
Need help?
Do you have a question about the PRO TH4110D and is the answer not in the manual?
Questions and answers