SDM-S51 US Model SERVICE MANUAL Canadian Model AEP Model SPECIFICATIONS LCD panel Panel type: a-Si TFT Active Matrix Dimensions (width/height/depth) Picture size: 15.0 inch Display (upright): Input signal format RGB operating frequency* Approx. 387 330 175 mm Horizontal: 28 - 60 kHz...
Page 2
SAFETY CHECK-OUT LEAKAGE TEST After correcting the original service problem, perform the following safety checks before releasing the set to the customer: The AC leakage from any exposed metal part to earth ground and from all 1. Check the area of your repair for unsoldered or poorly-soldered exposed metal parts to any exposed metal part having a return to chassis, connections.
Page 3
REMPLACER QUE PAR UNE PIÈCE PORTANT LE NUMÉRO PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE SPECIFIÉ. LES RÉGLAGES DE CIRCUIT DONT L’IMPORTANCE EST THESE COMPONENTS WITH SONY PARTS WHOSE PART CRITIQUE POUR LA SÉCURITÉ DU FONCTIONNEMENT SONT NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN IDENTIFIÉS DANS LE PRÉSENT MANUEL.
TAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically reduce power consumption as shown below. SDM-S51 Po wer mode Po wer consumption (po wer) ind icat o r normal 25 W (max.)
AUTOMATIC PICTURE QUALITY ADJUSTMENT FUNCTION Consequently, the first time the monitor receives input signals When the monitor receives an input signal, it automatically that do not match one of the factory preset modes, the monitor matches the signal to one of the factory preset modes stored in the monitor , s memory to provide a high quality picture at the center may take a longer time than normal for displaying the picture on the screen.
ADJUSTMENTS 2-1. FUNCTIONAL ALIGNMENT (1) •Procedures of how to go to service mode. 1. Hold “C” and “B” key power on, SDM-S51 goes into service mode. 2. Press “MENU” key-----ODS display contigulation RGB Reset contigulation Color Temp. 3. Press “-” key to go to second page’s late icon.
2. Click on ‘Setup’ menu. e. Adjust ‘sub_brt_B’ to achieve color temperature. • Equipm ent 3. Select ‘Monitor’ type as ‘Sony SDM-S81 ’. Refer to table 2 for specification. 4. Select ‘COM PORT’ according to hardware connection. f. Click ‘Save this color’ for a 9300K color save.
2-4. TIMING SPECIFICATION PRESET MODE MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6 MODE 7 MODE 8 SIGNAL MODE VESA 60Hz MAC 13” VESA 75Hz VESA 85Hz VESA 70Hz VESA 60Hz VESA 75Hz VESA 85Hz RESOLUTION 640 X 480 640 X 480 640 X 480...
Page 16
PRESET MODE MODE 17 MODE 18 MODE 19 MODE 20 MODE 21 MODE 22 VESA 60Hz SIGNAL MODE VESA 85Hz VESA 60Hz VESA 75Hz VESA 85Hz 1280 X 1024 RESOLUTION 1152X 900 1280 X 960 1280 X 960 1280 X 1024 1280 X 1024 DOT CLOCK 105.590 MHz...
6. Adjust White Balance (9300K, 6500K & 5000K) and Luminance 9300K 6500K 5000K Tolerance (10 nits @ SONY CS-1000) by Sub-BRT 0.2838 0.3132 0.3450 }0.003 Remark: In normally, adjust G for Luminance (Y), adjust R for x and adjust B for y.
3 x 4 PVTP 3 x 10 4-087-931-01 STAND ASSY(BLACK) 4-087-919-01 COVER, REAR(WHITE) 4-087-920-01 COVER, REAR(BLACK) 4-087-926-01 CABINET ASSY(WHITE) B2.6 x 5 4-087-929-01 CABINET ASSY(BLACK) PSW4 x 10 PVTP4 x 12 K3 x 8 P4 x 10 PTP3 x 8 SDM-S51(E) 4-2...