Clarke WOODWORKER CWL1000CF Operating And Maintenance Instructions Manual
40 (1000mm) wood lathe with copy function
Hide thumbs
Also See for WOODWORKER CWL1000CF:
- Operation & maintenance instructions manual (25 pages)
Related Manuals for Clarke WOODWORKER CWL1000CF
Summary of Contents for Clarke WOODWORKER CWL1000CF
- Page 1 40”(1000mm) WOOD LATHE WITH COPY FUNCTION Model No CWL1000CF Part No 6501670 OPERATING & MAINTENANCE OPERATING & MAINTENANCE INSTRUCTIONS INSTRUCTIONS GC0710...
-
Page 2: Introduction
GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase. -
Page 3: Table Of Contents
CONTENTS Introduction .................... 2 Guarantee ....................2 Environmental Protection ..............2 Parts & Service Contacts ............... 2 General Safety Rules ................4 Electrical Connections ................7 Main Components ................. 8 Unpacking & Assembly ................. 9 Operation ..................... 13 Maintenance ..................15 Troubleshooting .................. -
Page 4: General Safety Rules
GENERAL SAFETY RULES Important Note: Although the operation manual contains extensive instruction on safe working with power tools, every power tool involves a certain residual risk which cannot be completely excluded. Power tools must therefore always be operated with caution. WORK AREA SAFETY 1. - Page 5 before connecting to power source and/or battery pack, picking up or carrying the tool. 4. Remove any adjusting key or wrench before turning the power tool on . A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
- Page 6 ADDITIONAL SAFETY RULES FOR WOODLATHES 1. IMPORTANT: You should not operate this machine unless you are thoroughly familiar with woodlathes and turning techniques. If there is any doubt whatsoever you should consult a qualified person. 2. ALWAYS store chisels safety when you have finished with the machine. 3.
-
Page 7: Electrical Connections
ELECTRICAL CONNECTIONS WARNING! Read these electrical safety instructions thoroughly before connecting the product to the mains supply. Before switching the product on, make sure that the voltage of your electric- ity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. -
Page 8: Main Components
MAIN COMPONENTS ON/OFF Switch Tail-stock Body Speed Control Tail-stock Advancing Handle Headstock Centre Spur Tool Rest Support Tool Rest Faceplate Tool Rest Locking Lever Open Wrench Tool Holder T-Spanner Copy Tension Adjuster Drift Rod Copy Follower Cutting Tool(s) Tail-stock Spur Assembly Leadscrew Handles... -
Page 9: Unpacking & Assembly
UNPACKING & ASSEMBLY When unpacking, check for damage or omissions etc. Any found should be reported to your CLARKE dealer where the lathe was originally purchased. Do not discard the packaging until the lathe is assembled. WARNING: DUE TO THE WEIGHT OF THE LATHE BED ASSEMBLY, IT IS ESSENTIAL THAT TWO PEOPLE PERFORM THE UNPACKING, ASSEMBLY AND POSITIONING. - Page 10 ASSEMBLY OF THE STAND 1. Assemble the front & rear legs, supports and top plates using the coachbolts, nuts and washers as shown in Fig 1. 2. Assemble the stand loosely before tightening all the fixings together. 3. With the help of an assistant, position the lathe over the top plates and align the holes in the lathe bed with the holes in the...
- Page 11 4. Fit the leadscrew hub (79) onto the leadscrew axle (78) and secure with a grub-screw (50). If not already fitted, screw the leadscrew handles (113) into the leadscrew hub (79) and tighten by hand as much as possible. Fig 4 ASSEMBLY OF THE COPY FOLLOWER If the copy system is to be used Fig 5...
- Page 12 ASSEMBLING THE COPY TOOL 1. Install the copy toolholder rack Fig 7 (64) into the hole in the copy follower body (53) and drive it through using the handwheel (1) and the pinion gear (71) inside the copy follower body. 2.
-
Page 13: Operation
OPERATION 1. Ensure the cutting tool, tool rests and tailstock are securely locked in position before starting work. 2. Always rotate the workpiece by hand and check it does not strike the tool/tool rest before switching on the motor. 3. To turn the lathe ON, press the green push-button. Press the red button to stop. - Page 14 COPY TURNING 1. Take the template object which is to be copied and mark diagonal lines on each end in order to show the centre point before installing it in the copy stock position. Pierce the template with the copy spindle spur (8) and then tighten both ends equally to hold the template as shown in Fig 11.
-
Page 15: Maintenance
In case of problems refer to TROUBLESHOOTING on page 16. If you are unable to rectify any faults, please contact your local dealer or Clarke International Service Department on 0208 988 7400 for assistance. -
Page 16: Troubleshooting
TROUBLESHOOTING l l i . r i . r i , t i . r i f i l . t i f i l . y l l l i . r i . s r . t i s l i . -
Page 17: Technical Specification
" 4 s l i Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. -
Page 18: Parts List And Diagrams
PARTS LIST t f i s l i s l i s l i s l i i r r... -
Page 19: Parts Diagram
PARTS DIAGRAM When requesting spare parts, please quote the reference DDCWL1000 followed by the number (1-118) on the following parts lists. - Page 20 PARTS LIST ) t f t f i...
- Page 21 PARTS DIAGRAM When requesting spare parts, please quote the reference DDCWL1000 followed by the number (1-118) on the accompanying parts lists.
-
Page 22: Accessories
When requesting spare parts, please quote the reference DDCWL1000 followed by the number (1-118) on the following parts lists. ACCESSORIES The following range of accessories is also available from your Clarke dealer: 8-Piece Chisel Set Part No: 6500649 4-Jaw Independent Lathe Chuck Part No: 6500645 1/2”... -
Page 23: Declaration Of Conformity
DECLARATION OF CONFORMITY...
Need help?
Do you have a question about the WOODWORKER CWL1000CF and is the answer not in the manual?
Questions and answers