Advertisement
Advertisement
Table of Contents
Related Manuals for KIP 7100
Summary of Contents for KIP 7100
- Page 1 KIP 7100 ‐ User Manual Version A1...
- Page 2 Thank you for purchasing the Multi-Function Printer KIP 7100. This Hardware Operation Guide contains functional and operational explanations for the KIP 7100. Please read this Hardware Operation Guide carefully before using the printer. Please keep this Hardware Operation Guide for future reference.
-
Page 3: Installation Requirements
The equipment must be leveled and the floor strength must be ample to sustain the weight of the equipment. 30cm/12” or larger (Rear) KIP 7100 * L + R = 35cm/14” or larger (R must be larger than L) (L = 5cm/2” or larger... -
Page 4: Specifications
1. 4 Specifications 1. 4. 1 General Subject Specification Model KIP 7100 Configuration Console Power consumption 1,440W (US model) (Maximum) 1,680W (EU / Asia model) (scanner / controller included) Power consumption 30W or less (Low power mode) Acoustic noise Idling Max. -
Page 5: Printer Part
1. 4. 2 Printer part Subject Specification Printing method LED Array Electro photography Photoreceptor Organic Photoconductive Drum Print speed 80mm per second (Inch) 3.4ppm/E 5.8ppm/D Landscape (Metric) 3.3ppm/A0 5.6ppm/A1 Landscape Print head LED Array Resolution of print head 600dpi x 600dpi Print width Maximum 914mm / 36”... - Page 6 Subject Specification Media source 2 Roll Decks Manual Feeder (single cut sheet) Paper Tray (multiple cut sheet, option) Media (Recommended Media) US model: Bond 64g/m to 80g/m , US Bond (PB-20) Vellum US Vellum (XV-20) Film 4MIL (PF-4DDME) Europe/Asia model: Plain Paper 64g/m to 80g/m...
-
Page 7: Scanner Part
1. 4. 3 Scanner part Subject Specification Scanning method Contact Image Sensor (CIS) (5 pieces of A4 sized CIS) Light source LED (R/G/B) Setting of original Face up Starting point of scan Center Scan width Max: 914.4mm / 36” Min : 279.4mm Scan length Max:... -
Page 8: Turning On Kip 7100
In Europe : 220-240V plus 6% or minus 10%, 50/60Hz and 10A 2. Press “ | ” side the Power Switch on the right side of the printer to turn on the KIP 7100. Power Switch Press “ | “ side. - Page 9 Ready Indicator The UI screen may vary depending on your system configuration. (Shown with available options) 4. When Ready Indicator stops flashing, the KIP 7100 is ready for operation. NOTE It is impossible to make any prints while Ready Indicator is flashing in orange.
-
Page 10: Turning Off Kip 7100
” side. CAUTION The KIP 7100 print engine and UI appear to be shut down when you turn off KIP 7100. However, the controller PC embedded inside the KIP 7100 is still operating and will shutdown in approximately two minutes after Power Switch operation. -
Page 11: Canceling Sleep Mode
NOTE (1) It may take time for the machine to get ready. (2) Tapping on the UI screen can cancel the screensaver but the KIP 7100 needs to recover temperature on Fuser Unit. It may need another waiting time to start warming up for printing. -
Page 12: Dehumidifying Roll Media
Loss of image If the media is humidified; If the KIP 7100 is installed in such a condition, it is recommended to use the optional embedded “Dehumidify Heater”. Turn on the Dehumidify Heater if the room air has too much humidity (65% or higher) to prevent the above kinds of print defect.
Need help?
Do you have a question about the 7100 and is the answer not in the manual?
Questions and answers
Hello in the place of my employment we have an issue. We have a Kip7100 and when we accidentally may not press the right mailbox to go to a specific computer it's just stays on this blue default file called scans that says its on the mailbox but we cant acess those files in any computer. But the files are for sure scanned. How do we retrieve those files? Please help it's urgent!